Search Documents

By Robert Sutton, Milan Sjaus

Conveyor pulleys are an important and integral component of a conveyor. Conveyors work in sequence to make up conveyor systems. Each conveyor system is only as reliable as its crudest component. If the pulley fails, then the whole material handling system stops. So what is the effect of this downtime? What are the costs of repair? How much are we willing to pay to solve the problem? What should we spend to prevent an unscheduled shutdown? Do we use the technological improvements at our disposal or do we ignore them to satisfy immediate cost savings? This study will focus on the cost of pulleys relative to the total conveyor cost, the cost of downtime, the maintenance costs and the costs for resolution of the problem. Some philosophic and design concepts are injected for illustration and discussion.

Jan 1, 2000

By Z. Hyder, A. Urquidez

"INTRODUCTION The Waste Isolation Pilot Plant (WIPP) is located approximately 26 miles southeast of Carlsbad, New Mexico and is the nation’s first underground geologic repository for transuranic (TRU) and TRU-mixed waste (see Figure 1). The WIPP facility was opened for operation in 1999 when the first TRU waste shipment arrived at the WIPP facility for disposal.WIPP facility does not employ typical production aspects of a conventional mine. Instead, the mining focus is on the quality of the excavation to ensure safe disposal of TRU and TRU-mixed waste (Walls, 1991). GEOLOGY WIPP underground repository is mined within a 2,000 feet-thick bedded-halite formation (Salado Formation) (see Figure 2). The WIPP underground repository is located approximately 2,150 feet beneath the surface near the center of the Salado Formation. Geologic criterion and site-selection factors evaluated for the selection of the repository included topography, depth, thickness, lateral extent, lithology, stratigraphy, structure, erosion, dissolution, subsidence, surface water, aquifers, hydrologic transport, climatic fluctuations, manmade penetrations (U.S. Department of Energy, 1980).FACILITY DESIGN Profit did not play a major role in the WIPP’s conception like in a conventional mine. This was due to the extensive amount of additional regulations and safety controls that had to be built into the WIPP facility. Since it is nuclear and hazardous waste disposal facility, it must meet certain federal and state requirements for TRU-mixed waste. One of the major regulatory drivers for the WIPP facility is defined in the WIPP Land Withdrawal Act (LWA). One of the requirements in the WIPP LWA requires the DOE to submit documentation of continued compliance with Title 40 CFR Part 191, Subparts B, and C. These standards are regulated by the Environmental Protection Agency (EPA). The DOE must submit documentation of continued compliance (recertification) with these regulations every five years. In addition to the LWA, the Resource Conservation and Recovery Act (RCRA) is another major regulatory driver for the WIPP facility. Since the WIPP facility is categorized as a “Miscellaneous Unit” under 40 CFR, it must meet extensive environmental performance standards. These standards are defined in the WIPP Hazardous Waste Facility Permit (HWFP). The HWFP defines the terms and conditions that the Secretary of the New Mexico Environment Department has determined necessary to protect human health and the environment (U.S. Department of Energy and Nuclear Waste Partnership LLC, 2015)."

Jan 1, 2017

By Emmanuel V. Manlapig

The variables involved in a complex process like flotation can be classified as follows: a. Disturbance variables - which are undesired properties of the process input which affect the value of the process output but which are not subject to adjustment. They are the result of changes in the properties of the feed, like changes in head grade, flow rate, fineness of grind, etc. b. Manipulated variables (sometimes referred to as process variables or control variables) -which are those that are adjusted - reagent addition, aeration, pulp level - in order to compensate for the disturbances in the properties of feed. c. Performance variables (sometimes referred to as controlled variables) -which are those whose values measure the performance of the process. They are properties of the process output such as grade and recovery. The function of a control system is to maintain the process performance equal to the control objective in spite of the disturbances by adjusting the manipulated variables. Attempts at developing automatic control systems for mineral processing operations date back to the thirties and in many of these attempts the results were not surprisingly poor and un-stable. The poor results brought indifference and suspicion towards automatic control on the part of operators and management. The reasons for the apparent failure of these attempts were two-fold: a. the lack of adequate understanding of the behavioural responses of the process from the control point of view, and b. the lack of reliable control instrumentation which could withstand the harsh environment in mineral dressing plants. Many operators had accepted the fact that control of mineral dressing could be best conducted manually. In the case of flotation circuits, control had been virtually based on the skill and experience of operators particularly their ability to identify and rectify poor flotation performance aided by results from the laboratory (chemical) analysis of regularly collected samples from strategic points in the circuit which are at best, hourly collected samples.

Jan 1, 1978

By Ossi V. I. Hintikka

There are several limestone deposits around the Lohja area in southern Finland. Raw material for cement rock is mined from some of them. The formations are geologically complicated, and therefore selective mining is used whenever possible. One of these mines is the Tytyri underground limestone mine, which is divided into two parts; Törmä and Solhem. In addition to the selective mining system hand sorting or picking must be used at the Tytyri mine to improve the overall grade of the blended limestone. Some means were needed in order to improve the quality and to increase the feed rate by the elimination of hand sorting. Sorting machines were considered and eventually a Sortex 811MW was pilot plant tested at the Ojamo mine near Tytyri. This machine now continues to be used on production.

Jan 1, 1971

By Hanguang Wu, V. Izaxon, Sukumar Bandopadhyay

This paper presents an analysis of the heat transfer process between the mine ventilation air and the frozen rockmass. The heat transfer model takes into account not only by the mutual change in air and rockmass temperatures, but also by the phase change of ice-water- ice. Based on the analysis presented here it is concluded that the mine thermal regime can be regulated by having the air enter the mine through mined-out excavations or development airways.

Jan 1, 1995

By T. W. Camm

"Search Amazon.com using the keyword “leadership,” and you are rewarded with a list of over 144,000 titles. There is no shortage of books and articles, many of them well written, with excellent ideas. So why is there still a constant cry for effective leadership in organizations? Often, the person in charge has personal blinders that prevent them from seeing or understanding how to implement the newest leadership idea or method. Either deliberately or subliminally, there is a disconnect from learning about leadership, and actually modelling and implementing what has been learned. Some current research in leadership theory can provide insight and tools to address this issue. INTRODUCTION Let’s start with a discussion of terms. Pseudo is defined by Webster (2015) as “Being apparently rather actually as stated.” Synonyms include affected, assumed, contrived, fake, false, phony, pretended, and artificial. Antonyms for pseudo provide additional clarity, especially when we consider terms normally associated with effective leadership: genuine, natural, unaffected, unforced. A similar type from my world of academia is a pseudointellectual, “A person exhibiting intellectual pretentions that have no basis in sound scholarship” (Dictionary.com, 2015). This is a person pretending to have an interest in intellectual activities for status; a fraudulent intellectuality. The thought of applying the term pseudo to leadership first occurred to me while reading Power and Innocence by Rollo May (1972). In discussing the dynamics of power, and how the innocent are often victims of the exercise of power, especially the more aggressive and destructive types of power, he saw two types of innocence. The first he called authentic innocence, which he described as a childlike clarity that carried into adulthood. The second type he called pseudoinnocence, a type of naïveté that makes a virtue of powerlessness, weakness, and helplessness; being more childish than childlike (p. 48-50). Just as there is the potential for pseudoinnocence and pseudointellectuals, it is also possible to experience pseudo leadership. (I hope the gentle reader is not troubled by my decision to use pseudo leadership as two separate words, in contrast to the use of compound words for pseudoinnocence and pseudointellectual cited above. Since there is no official definition of pseudo leadership, I have exercised my author’s prerogative to treat it as two words, both because I think in this particular application this makes the most sense, and also I think it is easier to read). As we will see, there are numerous theories applied to leadership. What is so troubling to many of us in organizations, there are a myriad of “leaders” in companies espousing pet theories, but very few instances where the actions of these individuals match their words. This is a particularly important problem when we look at the effect this has on the day to day operations of a mine, and where effective leadership (or its absence) can have a profound impact on both productivity and safety."

Jan 1, 2016

By C. Asgaard

Asset availability has been a longstanding objective in mining and mineral processing plants around the world. Enormous resources in both dollars and manpower are invested in improvement efforts to achieve higher asset availability. One dimension of asset availability is the time equipment is out of service for large scale planned maintenance activity: grinding mills, kilns, furnaces, mobile equipment, shovels and draglines are all regularly taken out of service for extended repairs and service. The speed, cost and quality of these planned outages provide an opportunity to increase asset availability. Equipment shutdowns are projects that are executed in a compressed time period. This paper will describe how the overall time and cost of equipment shutdowns were significantly reduced at Cliffs Natural Resources Michigan Operations (CNRMO) through the introduction of the Critical Chain Project Management techniques.

Jan 1, 2009

By P. D. Rao

Although phosphorus is a very important biogenic element, its concentration in coal is generally low. Phosphorus concentrations typically range from 0.001 % to 0.229% in raw coals of the contiguous 48 states. Some Alaskan coals in the Cook Inlet region contain horizons unusually high in phosphorus. A foot by foot analysis of deep drill core, containing 70 ft. of sub bituminous 'C' coal from the Beluga coal field, Alaska, showed certain increments contained as high as 17.03% P2O5 in the coal ash; 1.01 % P on a moisture-free coal basis. Crandallite has been identified by electron microprobe analyses as a phosphorus numeral in these coals. The authors could quantify calcium, barium, strontium and phosphorus concentrations from the coal attributable to crandallite. These high phosphorus coals provided a unique opportunity to study the association of phosphorus in coals using chemical fractionation for exchangeable cations and acid extractable elements. Since the source of high phosphorous horizons in Cook Inlet coals is attributed to volcanic ash, it is suggested that the profiles of acid extractable phosphorous concentration may be useful for coal seam correlations.

Jan 1, 1992

By Georges E. Vaillant

Air pollution control in primary aluminum smelter . Various processes are known for air pollution in electrolysis plants. Mainly two systems have to be taken into consideration: -Treatment of concentrated gases collected directly from hooded pots. This is normally achieved by either dry or wet process. This is not the object of this paper as these processes have been already described. -Treatment of low concentrated fumes. A certain amount of gaseous and solid fluoride (35 % of total fluor pollution) goes out of the hooded pot. Gases commonly called secondary fumes are generally treated by wet process. The object of 'this paper is to describe two plants with specific treatment for secondary fumes. 1/ A plant in operation in Vlissingen (Netherlands) for PECHINEY. 2/ Presentation of tests carried out by a specialized Company. The results of such tests have been used for the design of the scrubbers presently under construction for ALUMINIO ESPANOL San Ciprian (Spain).

Jan 1, 1978

By Donald Babbitt

In 1971, during the planning and design stages of a $300 million expansion, the Iron Ore Company of Canada Ltd. through its Engineers, Canadian Bechtel Ltd., came out with a preliminary request for two (2) 10,000 LTPH belt conveyor scale systems. These Systems were to provide weighing accuracies within 2.5% of the iron ore pellets and concentrates in transit on two (2) 72" wide conveyors from the stockpiles to the ships. Each conveyor system would be fed by a rail mounted bucket wheel reclaimer, with the conveyed material moving directly to the ship loaders with no inter- mediate surge and/or storage bins between the stockpiles and the ships. The bucket wheel reclaimer discharge rates would vary from 0-9600 LTPH in cyclic periods, with the periods varying from 1-5 minutes - dependent on the level of the reclaim buckets in relation to the stockpile as well as the slewing rate of the reclaimer. There would be frequent interruptions for bucket wheel repositioning (laterally and vertically), changing ship holds, and trimming ship holds. These frequent zero flow conditions, approximately 500 per 150,000 ton ship, could last 1-5 minutes. In addition, the conveyors on which the scales were to be mounted would be over the water and subject to the wind and cold of Northern Quebec. These Systems would be in use 350 working days of the year and would load 30,000,000 LT/yr. (An average of 90,000/working day).

Jan 1, 1975

By R. Edward Williams

The Spa1lation Process Because of the low thermal conductivity of many hard rocks, rapid heating of these rocks produces a thin surface layer in which the temperatures attain high values. Thermal expansion of this surface layer is constrained by the reminder of the still cool rock, and when stresses within the surface rock become high enough, the surface rock breaks away from the cooler rock behind it and flies or falls off as a thin flake called a spall. Then the next, newly exposed surface is heated, and the process continues. This process is the basis of spallation drilling. The hot gases from a jet burner provide the heat for spallation to occur, and their high velocity provides a scouring action that transfers heat to the rock and removes the spalls as rapidly as they form. Spallation is a process which works in very hard rock. It is dependent upon the thermal expansion coefficient and the thermal diffusivity of the rock but is also affected by any discontinuities in the rock. To date the efforts which have been made to evaluate the various rock according to their spallability has been minimal. As the success of this process is dependent upon the characteristics of rock it is expected that the study of rock mechanics will prove to be of greater value to this program than to the other mechanism for drilling and excavating rock. Commercial Uses of SPALLATION In the 19408s, the Linde Air Products Division of Union Carbide (UC 1 began developing spallation for use in mining taconite ore, which is presently the chief source of iron in the United States. In this work UC developed a jet-piercing tool that burned fuel oil with oxygen to produce spallation and contained mechanical cutters to remove rock that was not amenable to spallation. The UC jet-piercing machines have since produced about 40 million feet of shallow blast holes used for emplacing explosives in the taconite mines. During this work it was found that hole diameters could be increased by merely reducing the advance rate of the burners and that existing holes could be enlarged by making another pass through the hole with the same burner. The Browning Engineering Go. of Hanover, N.H., has developed a hand-held spallation burner to cut slots in granite. It has been used for a quarter of a century and is now standard equipment for quarrying granite throughout the world. This burner, which resembles a small jet engine oriented with its exhaust pointed downward, is the forerunner of a flame jet burner used to spall experimental holes in granite at maximum rates in excess of 100 ft/hr when operating in hard, competent granite. It uses No. 2 fuel oil, which is burned with compressed air. The system uses water to cool the burner and the exhaust gases. These gases, along with the steam produced from the cooling water, blow the spalls from the hole. Experimental Work Theoretical and experimental work has been accomplished by the Massachusetts Institute of Technology and the Los Alamos National Laboratory. This work is reported in Refs. (3) and (4). To verify the experimental results of this work laboratory scaled down field tests were conducted using two we1 1 characterized granites from quarries in Barre, VT and Westerby, RI, under defined heating conditions. In the laboratory tests a propane - oxygen heating torch was used to direct a flame at the granite surface and the spal 1 ing process was examined at various heating rates with a high-speed video taping system operated at 200 frame per second. This produced a time-lapse sequence where the onset of the spallation process was easily distinguished. Also the heat flux from the torch to a flat surface at various stand off distances and flows was measured. A similar set of tests was conducted using the more easily quantified and uniform heat source of a 1.5 kw GO2 laser. This allowed accurate

Jan 1, 1986

By D. Wallace Fields

Increasing public pressure and demands from various tiers of government have generated a legislative maze of statutory and administrative requirements facing industries involved in mineral extraction and processing. Each tier, of government has asserted concurrent jurisdiction and threats of harsh measures if industry does not satisfy all requirements. In the field of water pollution control, federal requirements have increased, carrying with them increasing techniques of enforcement - ranging from injunctions through criminal penalties. Federal laws have required that states formulate water quality standards as an adjunct to federal regulation. Florida has reacted with the Water Pollution Control Act of 1967. This act incorporates state water quality standards and permit requirements for any installation constituting a potential source of pollution, and provides for civil sanctions as well as injunctive relief. The federal government has utilized an 1899 law to require a permit for discharges into navigable waterbodies - a term which has been judicially defined to include any watercourse capable, after reasonable improvement, for use in the transportation of waterborne traffic. Failure to secure these permits can result in the issuance of an injunction or civil or criminal penalties. The Corps of Engineers will not issue these permits without the approval of the discharge by state, local and other federal agencies. Air pollution similarly is regulated by a multi-tiered network of laws and administrative standards. Federal regulation has increased from early research support in the 1950's through the development of Air Quality Standards and their enforcement by large fines, injunctions, administrative conferences and public hearings. Florida regulation, under the Florida Air Pollution Control Act of 1967, parallels federal law but grants concurrent regulations, requirements and enforcement tools to local and state agencies. Although previous state regulation was minimal, consisting only of three acts passed in 189 1, 1899, and 1911, in the future the mining industry will have to contend with this increasing network of ecological requirements. It is recommended that the industry take the initiative by involving Florida in the Interstate Mining Compact, as well as seeking the passage of a state reclamation law funded by a severance tax.

Jan 1, 1972

By A. L. de Vegt

Hydrogen sulfide is an expensive chemical used in nickel, zinc and copper mining and metallurgical operations for selective recovery and concentration of metals from leach water streams, acid plant blow down streams, refinery electrolyte bleeds and precious metal plant bleeds. Hydrogen sulfide is either produced on site by catalytic reduction of elemental sulfur or transported to the site as liquefied hydrogen sulfide (H2S) or as a sodium sulfide solution (NaHS). Biologically produced hydrogen sulfide has economically very interesting application possibilities in the mining and metallurgical industry. Converting sulfates from waste streams into usable hydrogen sulfide by biological reduction results in operational cost savings in existing lime treatment systems. H2S can be produced biologically for less than $500/ton S. For the past ten years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove sulfate and heavy metals. The hydrogen sulfide produced is used for recovery of metals, mainly zinc, from the ground water stream. The system has been operating since May 1992 treating a flow of 5000 m3/d. At Kennecott's Bingham Canyon Utah copper mine a pilot plant started operation in November 1995 to develop the process for selective recovery of copper from leach water using biologically produced hydrogen sulfide from sulfate containing groundwater. Other pilot plants are operated at DOE's Pittsburgh Research Center and at Cominco Research focusing on selective recovery of metals.

Jan 1, 1998

By Arthur S. Cornford

According to Arbiter (Reference 1), the ball mill was invented by Brückner in Germany in 1876 and was first used in the United States on ores about 1905. The basic concept was a simple rotating cylindrical drum in which the tumbling action of the charge of material and grinding media resulted in size reduction of the material. Despite the very low mechanical efficiency of this method a number of factors have caused the tumbling mill to remain, by far, the most widely used piece of equipment for mineral grinding. The principal factors influencing this situation have been simplicity of design, ease of manufacture, ready adaptability to familiar material handling layouts and the absence of practical alternatives acceptable to the industry. In the early mills, the material was ground in batches, the mills being charged and discharged through doors in the shell. The shell was supported by means of solid trunnion shafts resting in plain bearings and the drive was accomplished through one of these shafts. In some later batch mills, the mill shell was supported on rollers which were also used to drive the mill. At an early stage, continuous operation was made possible by feeding and discharging the mill through hollow trunnions, the method still in most widespread use. The mechanical and structural design of the early mills was not an onerous engineering task. Norse sense and good practical knowledge were key qualifications. The mill shells had to be heavy enough to withstand the physical abuse they would receive in the field and the bearings had to have low enough unit pressures and sufficient wear retol to ensure several months of operation before the need for replacement occurred. When these requirements were satisfied, stresses developed in the equipment during operation were insignificant and the majority of structural failures were probably due to the use of inferior materials in manufacture. Over the years, the ever present demand for increased productivity has resulted in a steady Increase in the size of units of production equipment, including grinding mills. Arguments have been presented elsewhere, for and against the Idea of a high throughput single line grinding operation as opposed

Jan 1, 1972

By H. Shafick Hanna

The beneficiation characteristics of low grade Birmingham red iron ores of the Big Seam and Ferruginous Sandstone seams were investigated using flotation and magnetic separation after reduction roasting. Samples of Bib Seam Ore responded more readily to concentration than the Ferruginous Sandstone ores. The impurities inherent with the iron oxide minerals limit the grade of concentrates recoverable from these ores to a maximum of about 61% Fe if reasonable iron recoveries are sought. Flotation concentrates assaying 60-61% Fe and about 0.1% P with attendant iron recoveries of about 63% were achieved from Big Seam ore charges while those obtained from the low phosphorus Ferruginous Sandstone samples analyzed 54-56% Fe. Reductive roasting and magnetic separation of ground charges of the two ore samples yielded concentrates assaying 60-61% Fe. Iron recoveries were better than those achieved by flotation, but the magnetic products of Big Seam ore were high in phosphorus (0.2-0.3% P).

Jan 1, 1983

By R. L. Miller

"Why should we care about diesel quality amidst the complexity of mining for minerals? Mining companies use a large amount of diesel fuel in their worldwide operations, both for moving ore from the mine to the processing mills or transportation hubs, and to generate power for onsite processing. This creates a large carbon footprint and poses both environmental risk with the production of emissions, and public perception of how those companies do their business as stewards of the environment while incurring a huge fuel expenditure. To improve diesel quality and create incremental value and greater environmental stewardship, the opportunity is broken down into several segments: 1. Mining industry diesel consumption 2. Fuel quality issues 3. Impacts on operations, economics, and emissions 4. Potential solutions 5. How improved fuel quality saves fuel expenditures 6. Economics of improved fuel quality 7. Recommended testing process 8. Fuel quality analysis checklist MINING INDUSTRY DIESEL CONSUMPTION The average grade of mined Australian ore bodies has halved, while the waste removed to access the minerals has more than doubled over the last 30 years, thus increasing energy consumption by 70%, (http://eex.gov.au/industry-sectors/mining/). Energy consumption and intensity in mining and mineral processing is rising at around 6% per annum. The mining industry is a huge consumer of diesel fuel worldwide, and the SRS Rocco Report of 4 August 2014 gives a better picture of recent trends. To better understand the reasons to reduce both fuel costs and consumption, we need to compare metrics on the amount of diesel consumed per each ounce of gold produced over the last decade. The rate of diesel consumption in gallons per each ounce of gold produced for the top five worldwide gold producers has doubled in the last 8 years from 12.7 gallons per ounce in 2005 to 25.8 in 2013 as shown in Figure 1 below.This is caused by 1) lower ore grades requiring more hauls to get same amount of finished gold product, and 2) haul trucks moving ore from deeper sources in open pit and underground mines. For one large multi-national gold mining company, the 2005 waste rock / production ratio was 52 metric tons/gold ounce; by 2013 that ratio had grown to 113 metric tons/gold ounce per the same SRSrocco 4 August 2014 report. Using the metrics above, the top 5 gold miners used over 591 million gallons of diesel fuel in 2013. The cost of diesel in dollars per ounce of gold has increased from $30.48 in 2005 to $101.14 in 2013, an annual appreciation of 16.2% as shown in Figure 2 below."

Jan 1, 2017

By Gerald H. Luttrell

The determination of mass balances is the first step in analyzing the performance of processing circuits. Although conceptually very simple, the mathematics associated with mass balances can be cumbersome when conflicting data sets and/or complex circuits are evaluated. Fortunately, many of the spreadsheet programs available today include powerful search routines which can be adapted to solve common mass balance problems. To demonstrate these capabilities, a generalized mass balance program has been developed using the Microsoft Excel? spreadsheet. Compared to commercial programs, the spreadsheet format is user-friendly, more versatile and easier to customize. This paper reviews the mass balance problem and describes how spreadsheet tools can be used to reconcile conflicting data.

Jan 1, 1996

When most people think of coal mining, they envision men in soot-covered clothes and hard hats digging at deposits in deep underground caverns. These mental images commonly include coal cars rumbling on rails as they emerge from the earth, filled to the brim with rocky ore. The world of modern, longwall coal mining is a far different place. Yes, it?s underground, the miners still wear hard hats and the environment is filled with soot. However, today?s mining operations are carefully monitored and the entire process is highly automated. Five kilometers (3 miles) underground, a sophisticated, high-powered mining machine moves steadily through a 2-m (6-ft) high tunnel at an average speed of 3.2 km/h (2 mph), carving out coal, then conveying it to a crusher and carrying it to the surface. Instead of digging out the ore, a longwall mining system slices it from the exposed tunnel face, using giant rotating shears. The shorn coal tumbles onto a conveyer below the shears and is conveyed to the stageloader, where it is crushed and dumped onto the main conveyer belt that eventually hauls it out of the mine. Integral to the longwall shear and conveyor is a moving metal roof that protects it from the thousand plus feet of ground above. The ceiling panels automatically advance above the shears, powered by hydraulic roof supports that stand on the other side of the tunnel, moving in a slow, sideways lock-step with the shears. This complex and massive machine makes longwall mining the most ef?cient and productive method for excavating coal. In fact, it produces 2.7 kt to 22.6 kt (3,000 to 25,000 st) of ore per shift, versus 544 to 907 st (600 to 1,000 st) for the conventional room-and-pillar mining. Using that method, miners develop one section of a mine at a time after carving out load-bearing columns of coal to support the roof above their heads. Longwall mining also is considered safer than the room-and-pillar method, largely because the process is mostly automated, requiring fewer workers. Still, longwall mining has its drawbacks: The equipment is expensive and the mining conditions are harsh. An entire longwall system can cost between $50 million and $100 million, while the electrical controls used to operate it can cost an additional $1 million to $2 million. These investments grind away all day, every day, in hot tunnels filled with coal dust.

By H. A. DeMirjian

Oil production rate and ultimate primary recovery from a heavy or viscous oil reservoir is usually limited to a very small fraction of the original oil in place. Typically, normal production rate is in the range of up to 10 barrels per day and expected ultimate cumulative production is up to 10% of in place values. Heavy oil reserves are not all alike. The physical properties of the rock, the liquid hydrocarbons, and depths of the deposits are so different that each reservoir poses a unique enhanced oil recovery problem. In some reservoirs thermal recovery by internal heat generation or external heat injection has been successfully exploited. In other reservoirs, mining the oil bearing formation for oil recovery by surface processing has been practiced. This paper will present an overview of the heavy oil recovery state of the art and discuss the critical factors leading to the decision for selection of a conventional hydrocarbon recovery or mining and extraction processes.

Jan 1, 1978

The National Institute for Occupational Safety and Health (NIOSH) conducted field tests to evaluate the effectiveness of a wet head continuous mining machine for reducing dust exposure for continuous miner operators. Wet head technology delivers water via sprays to the continuous miner?s cutter head as opposed to traditional standard sprays located on the boom and body of the mining machine. The sprays, positioned directly behind each bit on the cutterhead, deliver water at the point of attack, serving to cool the bits during mining to reduce the potential for frictional ignitions. The sprays also flood the coal with water to potentially suppress dust generation. Dust surveys were conducted at several mines to evaluate the wet head?s effectiveness to control respirable dust exposure at the continuous miner operator location and in the immediate return. Results show that the wet head miner generally improved air quality at both sampling locations to varying degrees in some, but not all, mines when compared to a continuous miner with a standard spray system.

Jan 1, 2010