Search Documents

By Ivano Andreis, Georgios Kalamaras, Mario Liti, Sebastiano Pelizza, Filippo Avesani

"THE SS640 AGRIGENTO-CALTANISSETTA PROJECT The Caltanissetta tunnel is part of the works for the construction of the second 28km-long maxi section of the SS 640 motorway of Porto Empedocle, from km 44 to the junction of Imera in Sicilian hinterland. Amongst other major infrastructure works, the €740 million ANAS (Italian national roads and highway administration agency) project consists of four twin tube tunnels three of which are being excavated by conventional means. The longest tunnel, underpasses the Caltanissetta city and has a length of 3.9km under a maximum overburden of 120m. The JV consisting of CMC of Ravenna and TECNIS SpA won the design & built tender in 2010. Construction started in early spring 2012 following the approval of detailed design and later on the approval of design for construction. THE CALTANISSETTA TUNNEL The Design Phase Tender design and detailed design foresaw the construction of 13.4m excavation diameter tunnels that were to be enlarged in a second phase to create, every 600m, 50m-long tunnel sections for emergency parking. During the design for construction project phase the JV proposed to replace the 13.4m tunnel with a 15.08 excavation diameter that incorporated apart from the two 3.75m wide lanes a 3.25m wide continuous emergency lane. This significant tunnel section modification was associated with better road safety conditions, simpler and safer construction procedures, better statics for the tunnel section while in terms of overall cost the solutions were equivalent.Geologic context The tunnel is located in the middle of the geologically known Caltanissetta basin that is intersected by various tectonic structures. The geologic context for the tunnel scale, was defined in collaboration with the University of Catania in early project phases. For almost its entire length the tunnel is excavated in the Terravecchia formation that represents the lower part of the stratigraphic sequence that was formed in the Tortoniano period of Miocene. The quite complex geological model is also characterized by the presence of the so-called Trubi formation that consists of clay and marl clay. Almost 90% of the tunnel traverses formations that are quite similar in terms of excavation behavior. Exception to this are thrust zones and a calcareous stretch of the alignment. This last segment has a length of 200m and was identified since the very beginning as a tunneling challenge due to the combination of very poor geotechnical properties and an important water load."

Jan 1, 2016

By O. K. Olawale, G. O. Edaogbogun, B. N. Ben‑Festus, F. Ben, F. R. Amodu

The environmental and health implications of artisanal gold mining activities at mining sites across Nigeria have rekindled research interest. This study aimed to assess the scalability of naturally occurring radioactive materials in gold mining sites in Iperindo, Nigeria. Soil samples were collected from three different mining sites and control locations and analyzed for natural radionuclides, mainly 238U, 232Th, and 40K, using gamma spectrometry having a sodium iodide detector. The average activity concentration values of 61.55 ± 3.71, 72.65 ± 4.45, and 1134.99 ± 38.12 Bqkg− 1 obtained from within the mining sites for 238U, 232Th, and 40K, respectively, were above the world permissible values of 33.0 Bqkg− 1 for 238U, 45.0 Bqkg− 1 for 232Th, and 420.0 Bqkg− 1 for 40K. The average activity concentration values of 15.26 ± 3.19, 21.46 ± 4.27, 381.04 ± 23.36 Bqkg− 1 estimated for 238U, 232Th, and 40K, respectively, for the control location were, however, lower than the global permissible values. The study also evaluated other radiological parameters such as radium equivalent, dose rate, annual effective dose rate, internal and external hazard indices, and alpha and gamma indices. The obtained values were 252.83 Bqkg− 1, 119.98 nGyh− 1, 147.15 mSvy− 1, 0.85 Bqkg− 1, 0.68 Bqkg− 1, 0.31 Bqkg− 1, and 1.89 Bqkg− 1 respectively. Except for radium equivalent, external and internal hazard risks, and alpha index, which were significantly lower than the recommended threshold, all other radiological parameters were higher than the recommended global limits. Moderate data reproducibility and a p-value of 0.000574 further reinforced the robustness and reliability of the results obtained in this study.

Feb 22, 2024

By Emily Sarver, Cigdem Keles, Jonathan Gonzalez, Nishan Pokhrel, Lizeth Jaramillo

This paper presents a case study of respirable dust characterization in a thin-seam coal mine in southern West Virginia. Samples were collected in various locations within the mine and analyzed using scanning electron microscopy with energy-dispersive X-ray (SEM-EDX), thermogravimetric analysis (TGA), and Fourier transform-infrared (FT-IR) spectroscopy. The study found high non-carbonate mineral content, particularly aluminosilicates and silica, in the dust. The results indicate that fine aluminosilicate particles may interfere with SEM-EDX analysis, leading to an underestimation of coal content. The findings highlight the importance of using multiple analytical methods to accurately characterize respirable coal mine dust.

May 5, 2022

By Mustafa Kumral, Samer Hmoud

Effective management of ore loss and dilution is essential for successful grade control and short-term mine planning due to their significant impact on the economic, environmental, and technical aspects of open-pit mining operations. Factors influencing ore loss and dilution fall into two categories: (i) controllable factors like mine equipment selectivity and blast design and (ii) uncontrollable factors such as spatial heterogeneity of ore and waste blocks on a bench. This paper focuses on the second category by applying spatial entropy concept to capture heterogeneity at the scale of selective mining units. In this paper, global spatial entropy is used to assess the impact of spatial heterogeneity between ore and waste blocks on the magnitude of ore loss and dilution, while the local spatial entropy can guide the allocation of blast movement monitoring balls pre-blast. High values of the global spatial entropy indicate increasing potential of ore loss and dilution, which reduce profit. Furthermore, the study investigates the relationship between spatial entropy, cut-off grades, blast movement, dig-limits optimization model running time, and profit through a number of case studies. The results show that changes in cut-off grade and blast movement can significantly affect spatial entropy post-blasting and increase ore loss, dilution, and profit reduction, revealing the need for controlled blasting at specific bench sections. Additionally, the results demonstrate an exponential increase in profit reduction due to ore loss and dilution with a rising global spatial entropy.

Nov 28, 2023

By William Gleason

"Sometimes it’s the smallest things that make the biggest difference. In the world of mining, erosion can lead to small cracks, which can then lead to bigger problems that, over time, can eventually lead to a catastrophic event. However, when managed correctly, as in the case of the Manefey Slide at the Bingham Canyon Mine in Utah, the damage can be minimized.Numerous industry conferences, technical papers, studies and resources are dedicated to these issues each year, but what is sometimes overlooked is how the erosion of personal ethics can also have life-changing effects.At the 2019 SME Minnesota Conference, April 15-17 in Duluth, MN, two inmates serving their respective prison sentences at the U.S. Federal Prison Camp in Duluth spoke to the conference about how small cracks in their ethical foundations grew over time, eventually leading each man to his new address at the minimum-security facility.The men’s full names were not released and they were introduced as Jeff and Tony. Other than the matching green uniforms, both middle-aged men could have fit in with the rest of the crowd. They are well-educated and articulate whose career paths eroded thanks to greed and careless decisions.Tony, a licensed professional engineer, enjoyed a successful career working in contract oversight for the U.S. Department of Defense. Jeff is a former senior vice president of investments who ran a well-respected investment management team. Both spoke openly about the mistakes they made and emphasized that their crimes were not flagrant violations of the black and white rules but grew from ethical violations that live in the gray area between black and white, and right and wrong.Working in contract oversight for the U.S. Department of Defense (DOD), Tony said he was befriended by a wealthy man who was generous with his money. As Tony told it, a few meals with this man led to a few trips to casinos and eventually to gifts of money. The donor did not ask for anything in return, and at the time, Tony said he did not think that he was doing anything wrong. He admits now that the perception of a high-ranking officer in the DOD accepting gifts is not a good one, as it could be construed as the donor might have been trying to gain favor for future contracts; which is how it was presented in court by the prosecution team."

Jun 1, 2019

By George W. Bain

Deposits of metals in only slightly disturbed strata have been attributed to sedimentation processes contemporary with deposition of the strata. Recently this origin has been extended' to a greater variety' of deposits and local enrichment has been attributed to selective remobilization of metallic minerals in the host stratum. Effects attending metallization and deformation, and exact age' of the metallization are compiled to establish the sequence of events in ore deposit histories in order to clarify importance of remobilization within a formation relative to introduction from an outside source into an fav¬orable host. The pertinence respectively of deposit; origin and geometry to the work of the mining geologist is reviewed. Dwarf faunas in the Clinton iron ore, Tully pyrite bed and Rammelsberg deposit, indicate abnormal metal ions in the sedimentary environment. Slight¬ly disturbed strata are host rocks in the Swedish Kolm, Timna, Kupferschieffer, and White Pine deposit; the latter two have ore only in conjunction with tectonic structures.

Jan 1, 1966

By T. P. Meloy

A methodology is presented for finding feasible or locally optimal designs in the class of homogeneous, countercurrent, processing networks performing two-component non-sharp separations. The advantage of the methodology developed here is that given a set of independent performance criteria (specifications such as network separation factor, beneficiation ratio or recovery), a feasible or locally optimal countercurrent network design meeting those criteria can be found in one step. In the methodology, graph-theory was used to explicitly obtain the exact network responses of specific countercurrent networks. These responses were used to formulate the linear recursion equations whose solution gives the expressions for the countercurrent network responses which are a function of the stage transfer functions for two-component, non-sharp separations. These expressions are also functions of the network variables n and c. These expressions, together with the set of independent design criteria, were solved simultaneously for n and c using the Levenberg-Marquardt algorithm for systems of constrained, non-linear equations. The network variables n and c embody the coded network design information which is used to find the feasible network design which satisfies the set of independent performance criteria.

Jan 1, 1994

By Richard G. Almes

Since the failure of a major coal refuse disposal embankment and impoundment in the Buffalo Creek watershed near Man, West Virginia in early 1972, there have been extensive changes in the design and construction requirements for coal refuse disposal facilities located throughout the United States. The primary emphasis has been on improving the safety of these facilities, particularly for impoundments which are capable of storing millions of gallons of process water and storm runoff. The Mine Safety and Health Administration (MSHA) of the U.S. Department of Labor (formerly the Mining Enforcement and Safety Administration, U.S. Department of interior) has been the lead federal agency in promulgating regulations pertaining to coal waste disposal. In 1974 and 1975, studies were undertaken by our firm under contract to the Mining Enforcement and Safety Administration to prepare a comprehensive engineering and design manual to be used by operators and engineers in the planning and design of coal refuse disposal facilities with the intent ion of avoiding any more Buffalo Creek failures. The resultant 800-page document addresses major subjects such as safety, environmental controls, and cost. Specific topics include characterization of coal refuse, classification of disposal facilities, project planning, geotechnical investigations, testing and design requirements, hydraulic and hydrologic design, environmental factors, operations, and monitoring, instrumentation, and maintenance.

Jan 1, 1980

By Jeanne A. Zimmer, Andrew B. Cecala, Edward D. Thimons

The Bureau of Mines performed a study to determine optimal locations for longwall face methane monitoring equipment. Longwall face ignitions continue to be a concern to the U. S. coal mining industry. Gains in ignition control technology have been somewhat negated by advances in longwall productivity. More reliable, heavy-duty longwall face systems generate higher production rates and increase methane liberation rates. These rates will likely continue to rise in the future as further coal production increases occur. Efforts will continue in the areas of methane drainage, methane containment, and methane dilution. In addition, more effective face methane monitoring is needed. As technology continues toward automated longwall panels, the importance of monitoring for methane at the shearer becomes even more significant. Since the primary face ignition source is the shearer mining machine, the Bureau ran tests to determine the best location to take methane readings on the shearer. This information, in conjunction with data obtained from field studies, provides a knowledge base for selecting optimum face methane monitoring locations. INTRODUCTION Face ignitions are a concern for many U. S. longwalls and will continue to be until better control technology can be developed or until reliable and accurate knowledge can be provided as to when an explosive concentration is present. Figure 1 shows the number of reported U. S. underground longwall ignitions from 1980 to 1990. The number of longwall panels have remained relatively constant over this time period with 89 reported in 1980, compared to 96 in 1990. In spite of technological improvements in mining over the past decade, no significant reduction in the number of longwall face ignitions has occurred. One factor contributing to this is that the U. S. coal industry is mining gassier seams causing methane liberation rates on the average to be higher (Trevits, 1991; Grau, 1987). Another factor is the development and implementation of more reliable, heavy-duty longwall face systems that are generating higher production rates and higher methane liberation rates. Additionally, the average panel width in 1991 was 714 ft; a 44 pct increase from 1980 when faces averaged a width of 495 ft (Merritt, 1992). Increases in panel width also impact total face methane emissions. [ ] There have been substantial advances in control technology in the areas of methane drainage, methane containment, and methane dilution. In some mines, efforts to drain methane in advance of mining have proven effective, but geological conditions often preclude this approach (McCall, 1984; Ely, 1989). In other cases, ventilation air quantities of over 100,000 ft3/min and face velocities of over 1,000 ft/min have been implemented on longwall panels. Other operations have implemented anti-ignition spray systems which use water sprays behind each cutting bit to quench the hot streaks created from cutting noncoal materials (Courtney, 1990). Other control techniques, such as the modified shearer clearer system and ventilated drum, have been used to increase the amount of turbulence and ventilation around the cutting drums, thus reducing methane levels (Cecala, 1986; Divers, 1987).

Jan 1, 1993

By Nick Hasenack

In the pelletizing plant of Hoogovens, Estel BV, a varying mixture of hematites and magnetites is used for the production of acid and (occasionally) fluxed pellets. Optimum results regarding productivity, quality and process control are obtained with mixtures containing 30-40 % magnetites. A decrease of the magnetite ratio or an increase of the basicity has a great influence on both productivity and heat and power consumption. Tests have been carried out to find the extent to which magnetite can be replaced by b.f. dust, mill-scale and coke breeze. Pilot plant tests show that about 80-100 % of the production loss due to a decrease in magnetite content or to the increase in basicity can be regained without damage to the quality by adding coke breeze. The amount of coke breeze should be limited tot 1,5 %; if this percen¬tage is chosen higher, the quality of the pellets deteriorates rapidly. The amount of coke breeze to be added should be about 30 % above the theoretical value, based on heat balance considerations. The results achieved by incorporating b.f. dust and mill-scale into the pelletmix were also encouraging, but as some types of mill-scale are very difficult to grind and the supply of b.f. dust is limited, the research has not been carried out extensively in this field. The pilot plant tests on replacement of magnetite by coke breeze have been followed by industrial tests, during which the breeze was added to the ore feed before the dry-grinding system.

Jan 1, 1977

By M. L. Harris

Coal dust produced during the mining process is a prime explosion hazard in underground coal mines. To inert the coal dust and prevent a catastrophic propagating dust explosion, rock dust is applied to the roof, ribs, and floor surfaces of mine entries. Currently, one determination of whether a mine is adequately protected from the coal dust explosion hazard is made by analyzing collected mine dust samples for percent total incombustible content (% TIC). A minimum of 80% TIC is required per 30 CFR 75.403. The as-received moisture of the dust sample is included in the % TIC. Moisture and humidity within a coal mine vary greatly with the seasons, with explosions occurring more frequently during dry winter months. This paper will discuss the fluctuations of the as-received moisture content of the mine dust samples collected by U.S. Mine Safety and Health Administration inspectors in 2010 and the observed fluctuations of the moisture content of rock dust within the U.S. National Institute for Occupational Safety and Health Office of Mining Safety and Health Research Bruceton Experimental Mine and the Safety Research Coal Mine over a one-year period.

By K. H. McDaniel, L. Griswold

The Waste Isolation Pilot Plant (WIPP) is adding a third fan to operate in parallel with, and supplement, its two existing main fans. An engineering analysis conducted in 1995 identified the need for improved system availability and efficiency. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) Carlsbad Area Office facility designed to permanently dispose of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Engineers at the WIPP performed a feasibility analysis for either modifying, supplementing, or replacing its two main mine fans. Since the centrifugal fans were installed in 1988, multiple operational and performance concerns have been identified. A comprehensive engineering study was conducted (McDaniel, et al., 1997) to: identify and quantify operational concerns, evaluate possible alternatives, and recommend an optimum solution. The study indicated that adding a third single-duty centrifugal fan similar to the two existing fans, and equipping that fan with Inlet Van Controls (IVCs) was the best choice. This alternative provided the most desirable combination of operational readiness, and improving system performance. The fan installation project accommodates several operational and scheduling constraints. WIPP is scheduled to receive waste in May 1998. This milestone is proceeded by an operational readiness review. Fan installation could not be allowed to compromise the WIPP's ability to declare facility readiness and had to minimize operational disruptions during the system tie-in. All engineering for the project is completed and physical modifications started in July 1997. The project was completed in 1998.

Jan 1, 1999

By N. L. Bingham

The mining industry's image is molded by what the general public knows, or thinks they know about mining. As we prepared for the production of Caterpillar's educational film, Common Ground, we first had to find out exactly what the public perceptions about mining were. Before we could educate people about mining, we had to find out what they already thought. As we broke down those perceptions, we were able to narrow our focus to relevant, realistic approaches for the film. We found out what people didn't know about mining. And most importantly, we singled out the facts they should know... facts that could create more favorable attitudes. This research was instrumental in our final direction for the Common Ground project.

Jan 1, 1994

By Deepak Malhotra, Robert Dorfler

Modern engineering mill design has been refined over the years to the point where detailed ore and process specification criteria can be developed In the engineering design phase of the project. The plant Is then built to the detailed criteria and performance acceptance tested by the owner to see if the as-built mill meets the criteria, This performance testing is critical to the owner; the test must be systematic with sample collection coordinated throughout the plant. Despite the availability of systematic approaches to plant development, the new plants often fall short of design criteria. This paper discusses the key Issues a Project Manager/Process Engineer should Implement to ensure that plants meet design criteria.

Jan 1, 1991

By H. B. Trinh, R. R. Srivastava

"Spent auto-catalyst is a potential secondary resource because of the higher concentration of valuable platinum group metals (PGMs) as compared to the primary ores. Despite the well-developed commercially tenable technologies, further researches are being carried out to extract the PGMs with high efficiency. It is however, critical in this context to reuse not only the PGMs but also other metals contained in the spent auto-catalyst particularly that of the cordierite substrate such as aluminum, magnesium and cerium oxide (CeO2). This is important in view of the fact that no recycling process has ever stressed upon the recovery of cordierite substrate and CeO2 since the main target metals are mostly the PGMs. In this study, a new hydrometallurgical approach has been proposed in order to recover the PGMs as well as cerium oxide and materials from the cordierite substrate by using sodium hydroxide roasting followed by sulfuric acid dissolution. Under the optimal conditions for roasting at above 600°C, and weight ratio of sample to NaOH of 1:1 for 60 min, the cordierite was converted to the soluble phases. Dissolution of the roasting products using H2SO4 solution (1M) at 25°C for 60 min enriched the PGMs and Cerium oxide contents in the residue. Subsequently, PGMs in solution after dissolution can be cemented using Al and Cerium oxide in residue can be recovered by hot digestion using concentrated H2SO4.. INTRODUCTION Auto-catalyst can significantly control the gaseous emission of automobiles, and has been considered as a potential secondary source of Platinum group metals (PGMs) after being decommissioned from the vehicles. The PGMs demand is continuously increasing to comply with the growing vehicle population and the tightening of emission standards all over the world; meanwhile the natural resources of these metals is facing the threat of depletion. Therefore, it is crucial to progressively substitute with an alternate resource to supply PGMs other than that of the primary ores. Nowadays, vehicular transportations worldwide are totally installed with the auto-catalysts. However, they should be replaced after reaching their service life. If there is no recycling of such resources, huge amount of valuable metals will be wasted. The quantity of PGMs that can be recovered from the spent auto-catalyst depends on the size of car, which averages to 1-2 grams for small cars and 12-15 grams for the big truck; this is significantly higher than that of the primary ores containing 2-10 grams PGMs per ton. Consequently, the recovery of PGMs from spent auto-catalyst becomes extremely favorable as compared to the primary resources due to higher concentration of PGMs, with much lower and simpler processing steps, and lesser pollution."

Jan 1, 2018

By R. L. Loofbourow

SEVERAL categories of storage are used depending on capacity. Operational storage, which is small in comparison with the market, facilitates handling surges of a few hours' or a few days' duration. Seasonal storage, usually larger, permits accumulation of product during sea- sons when demand is low, for delivery when demand is high. In producing areas, large storage may permit production at a uniform rate, without waste or distress sale. Near large markets such storage increases the efficiency of transportation, allows a more extensive or higher grade market to be served, and affords protection against interruption in delivery.

Jan 1, 1959

By A. W. Khair

This paper presents an analysis of the dynamics of bit wear on the productivity of the continuous miners. Two field surveys have been carried out. The first survey was to assess the impact of bit wear on productivity and production cost. The second survey was to study the wear characteristics of the cutting tool (i.e. magnitude, forms, and mechanisms of bit wear). Primary factors affecting bit wear is identified and laboratory experiments were carried out to study the effects of some of these primary factors on wear in detail. Results indicate that bit wear has a significant effect on the productivity of the continuous miners. Furthermore under the severe geologic conditions (i.e. cutting rock partings and roof and floor rocks) bit wear not only hampers the productivity, but also increases the production cost due to a higher number of bit consumption. This study also indicated that bit wear accelerates beyond 20% of the conical height loss which corresponds to 7% of the weight loss. This increase rate of wear is an indicative of higher abrasion between bit body and cutting material, resulting in a dustier environment.

Jan 1, 1993

By Khosrow Badiozamani

Operating mines in Wyoming and Montana, which are generally characterized by shallow overburden and thick coal seams, are faced with reclamation problems which are unique to this area. Unlike the eastern or midwestern mines, removal of thick coal seams and lack of sufficient overburden creates overburden deficiencies that require careful evaluation prior to mining to insure compliance with regulatory requirements. Computer models and computer graphics can assist in such evaluation where appropriate alternatives can be selected which satisfies both the regulatory requirements and minimizes cost. This paper presents one such model used in evaluation of backfill requirements for restoration of surface and ground water regimes, restoration of mined-out areas to the approximate original contour, and the blending of the mined-out areas to the surrounding topography.

Jan 1, 1981

By Thon T. Gin

The lithologic, mineralogic, and magnetic beneficiation characteristics of the iron formation at U. S. Steel's Atlantic City Ore Mine, Fremont County, Wyoming, have been determined. The iron formation averages about 30 percent Fe content, and varies from 125 feet to about 500 feet in thickness. It is composed of interbedded magnetite-rich quartzites, magnetite-quartz-amphibole schists, and amphibole-chlorite schists. Quartz, actinolite-tremolite, chlorite, and magnetite are the essential mineral constituents. These rocks are differentiated into four major ore types on the basis of their relative quartz and amphibole content. The iron content of the magnetic concentrate decreases and the silica content increases with decreasing grain size and increasing amphibole content in each ore type at the same fineness of grind. Criteria were developed to enable the mine operator to recognize the ore types and to blend them to produce a more uniform concentrator feed. This results in less variation in product quality and requires fewer changes in operating conditions-in the concentrator.

Jan 1, 1965

By Gordon A. Gross

Banded siliceous manganese-iron bearing sediments recognized as distinctive facies of Algoma type iron-formation constitute low grade resources of manganese in many countries. Manganiferous facies associated with oxide and carbonate facies of iron-formation have iron to manganese ratios ranging from 0.2 to 2 and commonly about one. Manganiferous facies up to 30 meters thick occurring separately or with other iron-formation facies are associated with cherts, carbonates, shales, turbidites, tuffs and lavas. Primary cherty manganiferous facies and their gondite metamorphic equivalents represent significant manganese resources and are protores for higher grade deposits derived by secondary enrichment processes.

Jan 1, 1982