Search Documents

By R. S. Jurani

Sunshine Mining Co.'s Kellogg operation is the primary silver producer in the US. Maintaining a comfortable working environment in this deep underground mine historically has been a complex and costly problem. To improve the ventilation and cooling systems at a time of declining and un-certain silver markets, it was proposed to optimize the performance of existing facilities at minimum cost. This paper discusses a two-year, $400,000 optimization program that resulted in increased total mine airflow, cooler ambient temperatures, reduced compressed air usage, and lower energy consumption by primary fans, air compressors, and refrigeration plants. This saved the company about $650,000 per year.

Jan 1, 1988

By Charles F. Stack

The A. P. Green Refractories Co. operates clay mines in ten states. Eight of these states have reclamation laws with which we have to comply and indications are that the U. S. Congress will pass a federal surface mining reclamation act in the near future. These regulations, in addition to the value of land in most areas, dictate that mining and reclamation be considered as a single operation. In many instances the land may be more valuable after properly planned mining and reclamation than before. Refractory clay, commonly called "fire clay" is defined as a siliceous clay rich in hydrous aluminum silicates, capable of withstanding high temperatures. It is deficient in iron, calcium, and alkalies and approaches kaolin on composition. Refractory clay is much more limited in occurrence and usage than common clay or shale. During 1971, common clays and shales were mined in 47 states with a total production of 45 million tons. Fire clay production was reported in 22 states with a total production of only slightly over 3 million tons.(1) Many of these producing areas are extremely limited in extent and production. Several are contained within a one or two county area. This reflects the unique geological conditions required for the formation or development of fire clay. The major fire clay producing areas in the United States are shown in Figure 1.

Jan 1, 1974

By Daryl R. Tweeton

The Bureau of Mines measured the geochemical changes as H2S04 was used for in situ uranium leaching by Rocky Mountain Energy Company near Casper, Wyoming. Cores and ground water were analyzed before leaching. Water samples were taken from observation wells located between injection and production wells as the leach solution was brought up to full strength in several steps. Measurements were made of pH, Eh, temperature, conductivity, total dissolved solids, dissolved oxygen, HC03, U, V, Na, K, Ca, Mg, SO4, C1, Mo, Mn, Fe, Al, Si, F, P, As, and Se. The data were gathered to assist in geochemical modeling of leaching and to study the potential environmental effects of acid leaching. Environmental considerations appear favorable. For example, the concentration of Se, a toxic element often found in uranium deposits, stayed below the EPA standard for drinking water.

Jan 1, 1979

By Earl Parker

The mining/mineral processing industry constantly faces the challenges of handling tons of material in a variety of processes such as crushing, milling, drying, belt transfer and loadout. These processes result in the production of high volumes of dust. A variety of dust detection and collection equipment is needed to properly manage these emissions to remain compliant with stringent air quality and safety requirements. Dust monitoring and bag leak detection can provide ways to reduce air pollutants, make work environments safer and remain compliant with requirements from the U.S. Environmental Protection Agency (EPA), U.S. Mine Safety and Health Administration (MSHA) and U.S. Occupational Safety and Health Administration (OSHA). There are several approaches to monitoring particulate emissions from dust collection equipment. These can include visual inspections, differential pressure gauges or bag leak detection systems. Bag leak detection and monitoring systems can be optical, light based or electrostatic/triboelectric. Recent developments have advanced the efficiency and reliability of electrostatic/triboelectric style monitors. New technological improvements have been developed that are based upon the principal of unifying dc (impaction) and ac (induction) signals and incorporating other proprietary circuit innovations. This higher signal resolution technology results in a more robust and stable measurement for detecting the presence of particulate in a dust collector emission duct or a flow process pipe.

By K. H. McDaniel, L. Griswold

The Waste Isolation Pilot Plant (WIPP) is adding a third fan to supplement its two existing main fans. The third fan will operate in parallel with the two existing fans. An engineering analysis conducted in 1995 identified the need for improved system availability and efficiency. The WIPP, located near Carlsbad, NM, is a US Department of Energy (DOE), Carlsbad Area Office, facility that is designed to permanently dispose of US defense-generated transuranic waste in a deep, bedded salt deposit. Engineers at the WIPP performed a feasibility analysis for modifying, supplementing or replacing its two main mine fans. Since the centrifugal fans were installed in 1988, multiple operational and performance concerns have been identified. A comprehensive engineering study was conducted (McDaniel et al., 1997) to identify and quantify operational concerns, evaluate possible alternatives and recommend an optimum solution. The study indicated that adding a third single-duty centrifugal fan similar to the two existing fans and equipping that fan with Inlet Van Controls (IVCs) was the best choice. This alternative provided the most desirable combination of operational readiness and improving system performance. The fan installation project accommodates several operational and scheduling con¬straints. WIPP was scheduled to receive waste in May 1998. This milestone is proceeded by an operational readiness review. Fan installation could not be allowed to compromise the WIPP 's ability to declare facility readiness. Therefore, operational disruptions during the system tie-in had to be minimized. All engineering for the project has been com¬pleted, and physical modifications were begun in July 1997. The project was completed in 1998.

Jan 1, 2000

By Daniel Brutto

"Environmental considerations are a key driver within marine mining consenting processes across different national and international legislative regimes and are critical in shaping the global public perception of the industry. As a result, it is vital that mining companies seeking to operate within marine environments establish a robust understanding of the sensitivities of the seabed environments in which they are active, the impacts of their activities and the ability of the environment to recover from these impacts. The significant risks of failing to do so include an inability to either obtain or maintain operating permits. At the individual project level, the environmental effects of any given development project are typically defined within the scope of an Environmental Impact Assessment (EIA). For well-established industries operating in well-studied environments this approach typically works well. However, where emerging industries or existing industries that are operating within new environments are concerned, there may be significant knowledge gaps pertaining to our understanding of how specific anthropogenic practices or activities interact with the marine environment. These knowledge gaps can cause significant uncertainties pertaining to the likely significant effects of a project. Such uncertainties may result in barriers to industry and economic progress, increased consenting risks, increased project costs to be borne by individual project developers through the acquisition of additional environmental data during the pre-consent or post-consent project phases, project delays and/or significant increases in environmental monitoring burdens with corresponding increases in project costs."

Sep 1, 2014

By Alessandro Navarra, Aldo Quelopana

For decades, open-pit mine planning algorithms have incorporated geological uncertainty and other elements or characteristics for increasingly realistic representations. Among these complexities is the detailing of downstream processes that occur inside processing plants. Previous studies have demonstrated that the strategic mine plan and mineral concentrator design are coupled, and should therefore be optimized simultaneously within the same quantitative framework. However, existing frameworks offer limited representation of operational modes. This work demonstrates an approach to resolving this gap, in an optimization based on a parallelized Variable Neighborhood Descent (VND). The resulting algorithm embeds mass-balancing linear programming (LP) using a DantzigWolfe decomposition. A case study of a Zn-Pb deposit is presented to show the performance reached.

Jun 25, 2023

By David E. Siskind

The Bureau of Mines has studied the problem of cracking in residential structure walls from vibrations produced by blasting in surface mines. Direct observations were made of blasting damage consisting primarily of cosmetic cracking in plaster and gypsum board walls. Measurements of structure response and also application of the response spectra analysis single-degree-of-freedom model were used to quantify the frequency dependence of the safe level criteria. An overall summary analysis was performed using the new Bureau of Mines damage observations and data obtained from nine previous studies, including the three analyzed earlier by the BuMines for Bulletin 656, published in 1971. Separate analysis of the high- and low-frequency damage cases, structural response, and two types of construction resulted in the establishment of safe vibration levels ranging from 12 mm/sec to 50 mm/sec (0.5 in/sec to 2.0 in/sec).

Jan 1, 1980

By Greg Sanders, Bill Lueck, Michael Gilbert, Mahmood Khwaja

"The city of Minneapolis contracted with CDM Smith to update and provide a conceptual design for improvements to mitigate surcharge flooding in the Central City Storm Water Tunnel System (CCSTS). As a part of the project, CDM Smith conducted a field survey and condition assessment of the existing tunnel system. Information from the survey was then used to update the existing XPSWMM model and develop system wide alternatives.The CCSTS provides storm-water runoff drainage for nearly the entire area of the city’s downtown commercial district. The system consists of deep storm-water tunnels constructed in the St. Peter Sandstone, approximately 21 m (70 ft) below the street’s surface. The primary tunnels comprising the Central City storm water tunnel system are located below Hennepin Avenue, Nicollet Mall, Lesalle Avenue, Marquette Avenue South, 2nd Avenue South, South 5th Street, Washington Avenue South, Portland Avenue South, 2nd Street South, and Chicago Avenue South, as shown in Fig. 1. This network of tunnels conveys the runoff from a 305-acre tributary area that is generally bound by Hennepin Avenue and 1st Avenue North to the east, 12th Street to the south, 4th Avenue South and 7th Avenue South to the west, and 2nd Street South. These tunnels were constructed between 1936 and 1940, except for the Marquette Avenue South tunnel, which was constructed between 1963 and 1964.The CCSTS operates as a gravity flow system. These tunnels were constructed within the St. Peter Sandstone layer of bedrock and emerge from the bedrock at the Mississippi River below St. Anthony Falls. The Central City and the adjacent Chicago Avenue tunnel system converge into a single outfall at the Mississippi River. The runoff discharges from the converged outfall to a side channel of the Mississippi River, called a tailrace, located near the Guthrie Theater. The Minneapolis Division of Surface Water and Sewers provided 32 historic plats detailing the plan and profile of the tunnel system.The tunnel plans show nine different cross-section configurations. Eight configurations within the overall system generally show the same geometric “cathedral” shape with the inside dimensions varying from 1.2 to 1.8 m (4 to 6 ft) in width and 1.8 to 2.4 m (6 to 8 ft) in height. For analysis, these eight configurations were reduced to three configurations with regards to tunnel liner, cross-sectional area and support. For simplicity, the three configurations are described according to the three types of tunnel support used during construction: none required, light timber and heavy timber"

Jun 1, 2019

By Robert Rennie, Taylor Davies, Ahsanul Rafi

Electric locomotives powered by extensive electrical cabling systems were prevalent in the mining industry in the early days of the 20th Century [1]. Since the movement of tethered electrical mining locomotives was limited, the advent of diesel-powered mobile mining equipment provided more flexibility. This led the mining industry to be dominated by diesel-powered locomotives for most of the 20th Century and the entire 21st Century, to date. However, diesel power has certain drawbacks. Diesel-powered vehicles produce tailpipe emissions such as diesel particulate matter, carbon dioxide, sulfur dioxide, and nitrogen oxide. Mine workers exposed to these emissions were, and continue to be, subject to health issues such as respiratory problems, increased risk of lung cancer, and cardiovascular disease. [2][3]. Extensive ventilation systems are required to dilute the diesel exhaust and dissipate the heat generated by these vehicles. Moreover, as mines are getting deeper due to depleting resources, ventilation costs in diesel-powered mines are becoming increasingly high. These factors, coupled with the trend towards greenhouse gas (GHG) reduction in mine operations, has allowed zero-emission electric locomotive systems to gain traction. As lithium-ion battery technology is becoming more advanced, battery-powered electric vehicles can now perform duty cycles comparable to those of diesel-powered vehicles. Although battery-electric vehicles (BEVs) are comparable to diesel-powered vehicles in terms of mobility, they have certain limitations. For instance, the amount of onboard energy is limited by the battery energy density and specific energy. The MT42 diesel haul truck from Epiroc, for example, has a fuel tank capacity of 580L, which is equivalent to around 1450 kWh of net electrical energy [4]. The electrified version of the MT42, on the other hand, has an onboard battery with 375 kWh of usable energy weighing around 4.9 metric tonnes [5]. Moreover, storing and refueling of diesel-powered vehicles is simple and quick, whereas battery energy storage and charging systems require extensive infrastructure development. Charging time is mostly limited by battery chemistry and design. Due to these limitations, the benefits of battery-powered mining vehicles are more likely to be realized with proper planning and optimization of the BEV fleet. This includes optimizing mining layouts for BEV use, charging infrastructure design, and management of onboard energy storage systems.

Jun 25, 2023

By D. R. Barker

The economic performance and competitiveness of a concentrator are dependent on the production of accurate real-time assay information and the manner in which it is utilized. Our paper describes the relative merits of on-and in-stream analysis techniques and the economic significance of Assay-Based control and Target Oriented Display Systems. At Outokumpu's pyhasalmi Concentrator, a Flotation Expert Display System aids the process operator to make better decisions and provides guidance on the most efficient method of achieving the desired control objectives.

Jan 1, 1989

By Jan K. Wolski

The PC computer program PCVENT, version 3.3, for the ventilation network analysis now incorporates a real-time fire simulator. Position of the fire or a source of contamination and the character of the event are input from the keyboard. There are several options of type of fire: heat only, contaminant only, or both with a constant burning rate or with oxygen as the only limiting factor. Airway resistances or fan characteristics can be modified during a fire simulation. This allows testing of various fire suppression strategies. Program application in the analysis of a real mine fire is presented.

Jan 1, 1991

By Graham A. Davis

?The ideas of economists and political philosophers, both when they are right and when they are wrong, are more powerful than is commonly understood. Indeed, the world is ruled by little else. Practical men, who believe themselves to be quite exempt from any intellectual influences, are usually the slaves of some defunct economist. Madmen in authority, who hear voices in the air, are distilling their frenzy from some academic scribbler of a few years back. I am sure that the power of vested interests is vastly exaggerated compared with the gradual encroachment of ideas. . . . But, soon or late, it is ideas, not vested interests, which are dangerous for good or evil.? John Maynard Keynes The General Theory (1936) Policy analysts, economists and others have tradition-ally considered mining and mineral wealth a boon, providing rich countries with the resources needed to sustain their modern industrial economies while helping poorer countries generate the foreign exchange, tax revenues and other assets necessary for economic growth and development. Nevertheless, this conventional view has always had its critics.

Jan 1, 2008

By Juan P. Camus

One of the most important decisions in mine development is the selection of the mining method. Open pit or underground methods are selected depending on the shape of the deposit, and its position with respect to the surface. When the decision is not clear or evident, then the common rule is to compare underground and open pit projects to choose the one which yields the maximum return. However, in some circumstances' the best alternative is to start-up the operation with an open pit until a point where mine operating costs make more convenient to employ an underground method. In this case, the final pit limit is not directly related with commodity prices and its position is a funtion of capital and operating costs associated with both methods. The goal of this paper is a mans of establishing the proper ultimate pit considering a potential underground mine. The methodology is quite simple and can be implemented to work with a variety of available routines for pit optimization, such as Lerchs-Grossmann, floating cone, network flow and the Lemieux moving cone optimizing algorithm, which is the tool used by the author.

Jan 1, 1992

By P. Kawahata

Newmont?s Twin Creeks Mine, located in northern Nevada, is producing gold ore from surface mining operations. The ore is currently processed at three different on-site facilities depending on ore type and grade. Processing facilities operate under stringent geochemical blending constraints that must be met from mine ore deliveries and off-site sourced ore. To analyze various strategic options, the technical team utilizes the mathematical optimization approach. However, due to the size and complexity of the operation, there are unique challenges in optimizing life-of-mine production scheduling. This paper describes those challenges and methods developed to take advantage of different scheduling software to effectively compensate each other and result in reasonable guidance. This paper also describes how those scheduling results are reflected in detailed mine plan and cost estimate work.

Jun 1, 2013

By and Heather E. Lawson, Mark K. Larson, Gabriel Walton

In this study, we evaluated the effects of different shapes and distribution densities of mineral grains in coal on failure mechanics using the numerical software 3DEC. The main aim of this study was to identify possible failure mechanisms influenced by mineral habit and frequency in coal. Exploring differences in failure mechanics associated with the mineral grains helped to determine the role of mineral character as a possible contributor to characterize burst-prone coals. To achieve the goal of this study, a series of numerical specimens were prepared in the 3DEC model as follows: first, the 3DEC modeling in conjunction with the DFNs (Discrete Fracture Networks) technique was performed to explicitly generate the discontinuities (i.e., cleats and bedding planes) in the numerical specimens based on the results of laboratory analyses. Then, the different realizations of mineral grains were embedded in the 3DEC model to simulate an unconfined compressive strength (UCS) test to assess the influence of the mineralogical characteristics on the UCS.

By J. Herhold, S. Plaum

"Current and future operational processes in the mining and underground construction sector are under the influence of the prevalent competition and the acute necessity of optimization approaches concerning corporate and project processes. Besides general construction procedures, especially underground construction procedures and procedures in the field of deep shaft construction are high-profile. Those processes describe high technical challenges as well as increased requirements to occupational safety and health. Therefor an occupational safety management, which should be adjustable to the company itself and adaptable to all kinds of projects, shall be created. The creation of such an occupational safety management would lead to an economically optimized and safe (within the scope of OSH law) implementation of internal activities for the performance of construction services underground and in the field of deep shaft construction. With this approach the satisfaction of the high safety request as well as the demand for process optimization, as part of keeping the own competitiveness, will be satisfied successfully at once. PROJECT BACKGROUND Introduction The health and safety protection as well as occupational safety look back on a long historical development, which had brought more important sectors and developments during the last years, not only in Germany but also on the European and international level. The accident insurance protected by law has already been reported in 1884, which is astonishing early. The launch time point is strongly connected with the on-going economic development in the end of the 18th century, but above all this increased in the 19th century. The progress of occupational safety and especially the interest in the integration and the concentrated consideration of occupational safety and the health and safety protection in the company process is strongly visible during the 19th century and directly connected to the industrial revolution. [9] The industrial revolution and with that the development of work places lead to changing demands in the field occupational safety and health and safety protection. Insufficient security precautions caused problems in the industrial revolution, such as personnel and material losses as well as serious injuries and their consequences. These and the fundamental economic endeavours of the entrepreneurs lead therefore to the important step to develop an occupational safety system. [9] The prevailing basic ideas seize the insufficient security precaution of work places as well as the economical and profitable ideas of the entrepreneurs and bring them together. From this the necessary entrepreneur’s task comes into being and that is bringing the work conditions to the way that life and health of employees are not in danger. [9]"

Jan 1, 2017

By Elżbieta Węglińska, Andrzej Leśniak

The earthquake locations are generally scattered mainly due to a simplified velocity model or seismic event picking errors. The aim of our research was to increase the resolution of the cloud of microseismic events recorded during mining activity in the Bobrek hard coal mine on the 3/503 coalface to delineate seismically active structures using unsupervised machine learning algorithms. We presented results of applying two completely different algorithms for reducing scatter in microseismic location to all events recorded during mining activity on the coalface - the collapsing (proposed by Jones and Stewart in 1997) and condensation (proposed by Kamer in 2015). The collapsing method simplifies the seismic cloud by shifting events inside their error ellipsoids towards local source densities. The error ellipsoids are determined by errors in the measured parameters and seismic network configuration. The advantage of the collapsing method is the partial elimination of blurring of the microseismic cloud. The condensation method reduces the size of the set of seismic events without changing the geometrical information. The reduction of the number of seismic events in the catalog takes place through the condensation of localized events with larger uncertainty into events with lower uncertainty. The spatio-temporal analysis of microseismic events was performed separately on two processed clouds – collapsed and condensed one. We examined how collapsing and condensation methods affect the automatic detection of clusters of microseismicity using density-based spatial clustering of application with noise algorithms. We compared structures detected by the machine learning algorithms in both seismic clouds first created by collapsing and second by the condensation. We identified structures created by mining activity and structures related to the local tectonics activated by mining. The presented results are essential for the prediction of future tremors induced by the mining operation and tectonics and thus ensuring safety in the mine.

Apr 26, 2022

By Robert Y. Lamarche

INTRODUCTION Production of chrysotile asbestos from the northern Appalachians has been going on for 100 years and, on the basis of known reserves and the present rates of mining, appears assured of continued production for at least another 25 to 30 years. In spite of this, mining companies and government agencies are showing an increasing interest in exploring for chrysotile asbestos throughout this region and elsewhere in the world, implying that increases in the rate of consumption are envisioned. This chapter describes the geologic and tectonic settings surrounding these important chrysotile deposits, with emphasis on those in southern Quebec that yield about 90% of the total production from the northern Appala- chians. Detailed descriptions of a few individual deposits are also given, along with exploration guidelines aimed at facilitating the discovery of additional chrysotile deposits. One section of this chapter deals with the origin and mode of formation of the chrysotile deposits in the light of modern day concepts of plate tectonics. The objectives of this chapter are to give a brief description of the geologic and tectonic settings of the ultramafic rocks in which the numerous chrysotile deposits of the northern Appalachians are found; to describe a few of the individual deposits; to give a few exploration guidelines for those interested in exploring for new asbestos deposits in similar geologic environments; and to propose a new model for asbestos genesis in light of the recently developed theories of global tectonics. As this chapter is based almost entirely on field and laboratory observations, rather than on the study of experimental laboratory models, most of our deductions and suggestions are empirical in nature and may be interpreted in more than one way. The interpretations we have selected seem to offer, we feel, the best explanation of observed geological phenomena (Lamarche and Wicks, 1975). This region had a production capability in 1979 of close to p.5 Mt of chrysotile asbestos with 92% of this tonnage being derived from the deposits of the Eastern Townships of Quebec. With known resources, which now stand at between 36 and 40 Mt of fibers, this production capability seems assured for the next few decades. In spite of all known reserves of chrysotile asbestos, which now stand at between 36 and 40 Mt of fiber in this region alone, mining companies and government agencies are still showing a good deal of interest in exploring for new sources throughout the world. GEOLOGICAL SETTING The asbestos deposits at Baie Verte in eastern Newfoundland, Thetford Mines, Black Lake, Asbestos in southern Quebec, and Belvidere Mountain in Vermont, all occur in partly serpentinized ultramafic rocks that are part of the Lower Paleozoic ophiolite complexes of the northern Appalachians [Cady, Albee, Chidester, 1963, Chidester, Albee, Cady, 1978, Lamarche, 1972,1973, Laurent, 1973,1975, Williams, Hibbard, Bursnall, 1977, Norman and Strong, 1975). The deposits to the northeast of Thetford Mines, on the other hand, are found in a more highly serpentinized ultramafic body known as the Pennington dike, whose spatial, genetic, and chronological links with the ophiolite masses proper have not as yet been adequately resolved. The Appalachian ophiolites are part of an ultramafic belt (or belts), that extends from northwestern Newfoundland, through Quebec and Vermont. Fig. 1, and southwestward as far as the

Jan 1, 1986

By R. Asamoah, P. Forson, W. Skinner, M. Zanin

Despite the seeming benefits decoupling pyrite and arsenopyrite minerals present in practice, little success has been achieved. The present study presents possible process routes for attaining selective flotation broadly capitalizing on differential oxidation between these minerals, and the use of a chelating collectors. The best performance was achieved with dithionocarbamate application following copper activation, yielding 81.4% arsenopyrite and 37% pyrite recovery. Preaeration followed by staged addition of xanthate produced 76% arsenopyrite and 31% pyrite recovery while reverse flotation of pyrite after H2O2 addition gave rise to rejection of 66% pyrite accompanied with 24% arsenopyrite.

Mar 2, 2022