Search Documents

By A. R. Laplante

A test to determine the amount of gravity recoverable gold (GRG) in an ore is described. Typical GRG results are given; an error analysis is detailed; possible uses are discussed. Of the 38 samples tested, the lowest GRG content was found to be 25% (most below 25 11m, or 600 mesh), and the highest 94% (most above 300 11m, or 50 mesh). The average GRG content was 63%, with a standard deviation of 19%. Error analysis shows the test to be reproducible within 5 to 10%, depending on the size distribution and grade of GRG, and the sample extraction protocol. When using the same primary sample, reproducibility improves, 2 to 5%, depending on the amount of gold coarser than 850 11m (20 mesh) and sample weight. The test has been applied to greenfield project and retrofit applications, to determine the suitability of gravity recovery. For existing circuits, it has been coupled with a model of gravity recovery for optimization studies.

Jan 1, 1996

By Darold Woodward, Stefan Haydn, Petr Pospisil

Most fatalities in tunnel fires are caused by the spread of toxic smoke. Controlling the spread of smoke is crucial to provide a survivable environment for emergency egress. A properly designed and tuned feedback control loop is required to achieve a target flow that is slow enough to allow pedestrians to escape under different boundary conditions. Feedback control loops are also helpful in optimizing energy consumption under moving traffic conditions. A reliable feedback flow control system requires sophisticated engineering knowhow and experience, careful selection of instruments and controlled variables, and thoughtful implementation from design through field testing and commissioning.

Dec 1, 2022

By Evan Dressel, Mark S. Diederichs, Kathy Kalenchuk

As hard rock mining develops deeper over time, there is an increasing need to predict the spatial and temporal distribution of adverse seismogenic rockmass reaction to mining. Real-time monitoring and feedback of mine data are used to tactically manage risk associated with induced-seismicity; however, strategic risk management requires reliable tools for forward predictions of seismic hazard. The forward prediction of seismic hazard is strengthened by understanding of potential seismic intensity, which often relies on well calibrated mine-wide numerical models. This paper uses a case study to explore how future seismogenic potential and the nature of future seismicity can be domained according to numerically predicted stress-strain paths at past seismic event locations. Delineation of high confinement seismogenic volumes vs. lower-confinement, high-strain seismogenic volumes at the mine-scale can be achieved, based on a loading and unloading stress path analogue, to refine understanding of seismic intensity. Practical qualitative and quantitative methods to achieve this delineation will be demonstrated. Once seismogenic mode (high-stress vs. high-strain) is identified, detailed analyses of seismic source parameters demonstrates change in seismic hazard between the domained volumes.

Apr 26, 2022

By Jaisen Kohmuench, Michael J. Mankosa

Flotation has long served as the foundation for sulfide mineral recovery. As ore grades decline, however, this traditional approach is being pushed to the limit. Nowhere is this more evident than in the challenge of recovering coarse, partially liberated particles — an area where conventional flotation systems typically underperform due to excessive turbulence. As a result, valuable coarse minerals are often lost to tailings. Fine grinding has become the default solution, although with the added burden of higher operating costs and more challenging tailings disposal. To address the challenge of coarse particle recovery, Eriez developed the HydroFloat, a technology that uses a novel fluidized-bed approach to extend the upper particle size range of flotation significantly. The HydroFloat can recover particles exceeding 0.5 mm in diameter with a sulfide surface expression as little as 2 percent. Coarse particle recovery allows for optimization of comminution circuits for coarse gangue rejection before fine grinding. A substantial increase in overall tailings particle size provides higher water recovery due to improved drainage and allows for consideration of a dry, stacked tailings option instead of a tailings dam/impoundment. The technology’s transformative potential has not gone unnoticed. In recognition of its impact, Eriez was honored with the 2024 Robert E. Murray Innovation Award, commonly referred to as the Murray Award, by the Society for Mining, Metallurgy & Exploration. This prestigious award was established in 2017 to recognize organizations that advance the mining industry through the implementation of technical innovation. The HydroFloat stands as a fitting example of how creative thinking and industry collaboration can solve long-standing technical challenges.

Oct 1, 2025

By Pei‑liang Xu, Jun Wang, Xi Zhang, Deng‑pan Qiao, Tian‑yu Yang

The surface backfill, serving as the operational platform for continuing mining in upward slicing and filling stopes, is required to possess sufficient strength and thickness. Currently, there are limited model methods for determining the strength and thickness of the surface fill body. By analyzing the mechanical actions on the surface backfill, it is determined that its stability is mainly influenced by the combined effects of normal and tangential uniform loads under full-load conditions of trackless equipment. Assuming a circular contact surface between the tire of the trackless equipment and the surface backfill, and utilizing solutions from elastic mechanics theories such as the Boussinesq and Cerruti solution, the stress and displacement distribution of the surface fill body were obtained. Based on the maximum vertical stress condition, where the surface backfill body undergoes maximum deformation while still in an elastic state, and considering the stress–strain relationship, a model for the strength and thickness of the surface backfill has been established. According to the research findings, the design for the strength and structural parameters of the surface backfill has been developed to meet the full-load operation of the Atlas ST7 scooptram, with a compressive strength of 1.32 MPa and a thickness of 0.5 m. Numerical simulation analysis results indicate that the stress and displacement of the surface backfill align with theoretical analysis results. Practical results from industrial application in the western section of the Dahongshan Copper Mine demonstrate that the designed strength and thickness of the surface backfill meet the operational requirements for trackless equipment, resulting in significant engineering application effects and economic benefits. The research findings hold significant importance for advancing the theory of backfill mining and have high applicability and promotional value for similar mines.

Mar 24, 2024

By Chiranjibi Santi, Amit Kumar Gorai, VIVEK KUMAR HIMANSHU

Air overpressure (AOp) and peak particle velocity (PPV) are the most undesirable effects of blasting in mines. It is an urgent need to design a predictor model for AOp and PPV for universal applications to minimize environmental effects and damages that occur due to blasting. The present study attempts to design an artificial neural network (ANN) model for the prediction of AOp and PPV in different conditions. In this study, the blast design parameters (number of holes, depth of the blast hole, stemming length, spacing, burden, distance of vibration monitoring location from the blast site, charge weight per delay) of two active mines (coal and iron ore) are considered in four different conditions for training and testing of the model for the prediction of AOp and PPV. The model was trained and tested in four different combinations of data (trained using data of one mine and tested using data of another mine, trained and tested using data of coal mine, trained and tested using data of an iron ore mine, trained and tested using combined data of both the mines) for examining the applicability in different conditions. The results indicate that R2 values are ranged from 0.886 to 0.908 and 0.8728 to 0.8959, respectively, in the prediction of PPV and AOp. A comparative study of the performances of the developed model with the other empirical model is also demonstrated. For this, the site constants of different empirical models were estimated individually for both the mines. The study results indicated that the ANN model performs much better than all the empirical models. It can be inferred from the results that blast vibration cannot be accurately predicted only from charge per delay and distance from the blast hole. The ANN model was considered many other factors and thus can predict the vibration level more accurately.

Jul 30, 2021

By J. A. Marts, R. C. Gilmore, S. Saki, J. F. Brune

El modelamiento de la dinámica de fluidos computacional (CFD por sus siglas en inglés) implica la creación de un dominio de cálculo llamado malla o rejilla para resolver las ecuaciones que definen la física del flujo de fluidos. Este proceso comprende a menudo emplear la mayor parte del tiempo en esfuerzos de modelamiento. En un proyecto patrocinado por el Instituto Nacional de Seguridad y Salud Ocupacional (NIOSH), los investigadores de la Escuela de Minas de Colorado utilizaron un enfoque innovador de mallas, el cual permite una fácil adaptación del modelo CFD para adaptarse a una variedad de geometrías de minado de tajos largos ventilados por canales (bleeders) y progresivamente sellados (referidos a menudo como bleederless en los Estados Unidos), con la porosidad y la permeabilidad de la cámara escalables en un amplio intervalo. En este trabajo se presenta la metodología del enfoque de enmallado y escalado junto con las recomendaciones para el uso de modelos CFD en aplicaciones de ventilación para las cámaras en tajos largos. La nueva técnica de enmallado se utilizó para evaluar la función de un retorno hacia atrás en una cámara progresivamente sellada y otra cámara ventilada por canales.

Jan 1, 2014

By J. A. Marts, R. C. Gilmore, S. Saki, J. F. Brune

Computational fluid dynamics (CFD) modeling involves the creation of a computation domain called a mesh or grid to solve the equations defining the physics of fluid flow. This process often comprises the majority of time spent in modeling efforts. In a project sponsored by the U.S. National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines used an innovative meshing approach, allowing easy adaptation of the CFD model to adjust to a variety of longwall bleeder-ventilated and progressively sealed (often referred to as bleederless in the United States) mining geometries, with gob porosity and permeability scalable over a wide range. This paper presents the methodology of the meshing and scaling approach along with recommendations for using CFD modeling in longwall gob ventilation applications. The new meshing technique was utilized to evaluate the function of a back return in a progressively sealed gob and a bleeder-ventilated gob.

Jan 1, 2014

By L. J. Buchanan

The relationship between hydrothermal ore deposits and hot spring systems has received intensive study in recent years, particularly as a consequence of interest in the energy potential of geothermal systems. Base and precious metal deposition in surface pools and at shallow depths in modern geothermal systems has been recorded in numerous publications (1, 2, 3) Theoretical studies of hydrothermal fluid flow at depth, connected to surficial hot springs systems, have been presented by White and others (1), Cathles (2) , Henley and McNabb (3). As a result of these and additional studies, numerous hydrothermal ore deposits are thought to have originated as genetic parts of larger geothermal systems. In particular, it appears that metal precipitation is greatly enhanced in zones of boiling where volatiles and steam are escaping (4). High grade, near surface concentrations of base and precious metals, deposited as a result of partial vaporization of rising fluids, are such a common aspect of modern not spring systems that ore deposition models are becoming based on what may be called a geothermal model. In its most general terms, this model requires an anomalously high thermal gradient which acts as the driving force behind a convecting hydrothermal system. The water may be entirely meteoric or may be In part at least of other origins. The water migrates towards the higher temperature area, becomes heated, and picks up alkalies and metals by dissolving minerals along the fluid path. As water exits to the surface above the heat source, a mass balance requires the incoming hot water to rise to replace the lost water. As the water rises past the elevation where the hydrostatic pressure is insufficient to prevent boiling, then boiling will occur. Depending on the salinity and the temperature of the water, boiling can occur anywhere from great depths to near surface. Boiling results in a loss of volatiles, a pH rise in the fluid phase, cooling of the remaining fluid, a rise in oxygen fugacity, a concentration of salts in the remaining liquid, and precipitation of ore and gangue minerals.

Jan 1, 1980

By P. Lopez, E. Wellman, N. Risso, A. Anani

Current machine learning models used for roof fall hazard prediction are mounted on expensive sensors, computationally expensive, or lack the robustness for accurate prediction in the underground mining environment. This research aims to provide a design methodology for a robust, low-cost, deep learning-based algorithm for underground mine roof fall hazard prediction. A data sampling plan is developed to ensure the replicability and robustness of the developed model. In addition, feature engineering and transformation methods are described to identify relevant features for hazard identification. The methodology described here will be used in model development, tested, and implemented as a real-time mobile device application. The new tool will be expected to detect roof fall hazards in real-time and contribute to a crowdsourcing approach for underground hazard detection.

Feb 1, 2023

By Robert W. Greene

Next month, American Commercial Barge Line Company will begin moving coal from mines on the old Camp Breckinridge property in Western Kentucky to TVA's new 2600 MW steam plant at Cumberland City, Tennessee. By April of 1973, this movement will reach a level of 7,000,000 tons per year. TVA bought the coal rights to this property from the General Services Administration in 1965 for approximately $7 million. The reserve contains about 120 million tons of recoverable No.9 coal, and about the same recover-able amount of No. 11 coal. TVA then contracted through competitive bidding with Peabody Coal Company to mine the No.9 seam through two slope shafts. The mines are about 300 feet deep and are separated by the one major fault on this property. The mine portals are approximately 3-1/2 miles apart, with the northern portal being over nine miles distant from the Ohio River (see Figure No.1). In 1969 TV A took bids on alternate methods for transporting 120 million tons of coal to Cumberland City at seven million tons per year. These alter-natives included overland transportation to the Ohio River by rail or conveyor, water transportation from Union County, Kentucky to Cumberland City, and total transportation packages from Camp Breckinridge to Cumberland City. The latter could be a joint land/water package, or all land (rail). Ultimately American Commercial Barge Line was awarded an $88 million package transportation contract to convey the coal from Camp Breckinridge to Uniontown, Kentucky; to store it at Uniontown in a quantity sufficient to allow ratable delivery to the steam plant; and to barge from Uniontown to Cumberland City via the Ohio and Cumberland Rivers.

Jan 1, 1971

Traction of mining vehicles is well understood for a variety of unfrozen road surfaces, allowing optimal design of mine access and haulage roads. However, no such characterizations exist for the frozen or partially frozen surfaces typically encountered in Northern regions. Recent work by U. S. Army researchers suggests methods for characterizing roadway traction for any vehicle on the basis of test measurements made with a standard test vehicle. Such a test vehicle was designed, and several sets of test data were recorded at the onset of winter in Fairbanks, Alaska. This work suggests methods for future research and possibilities for the use of such research in designing drive systems, tires, and mine roads for Arctic and sub-Arctic mines.

Jan 1, 1995

By Patrick J. Ryan, Johann F. Kerl, Angelos N. Findikakis

Introduction Tailings disposal methods used by the mining industry include the use of on-land impoundments, surface and underground mine backfill and marine disposal. The latter method, where applicable and under certain circumstances, can be the most economical and best environmental option. The term marine disposal is used to describe deposition of tailings in the open ocean, coastal waters, fjords and inland lakes. A major element in planning and designing a marine outfall is the assessment of its potential environmental impacts. The nature of the disposed tailings, and the physical, chemical, and biological characteristics of the receiving water body must be carefully assessed prior to deciding whether marine disposal is an acceptable option for a particular project. During the last decade, the North American mining industry has demonstrated a commitment to studying potential adverse environmental impacts of marine tailings disposal and to continue monitoring of the receiving waters. Extensive monitoring programs have been undertaken by Canadian mines. Marine tailings disposal is not used in the United States today. One of the largest U.S. mines proposing to use this option is the Quartz Hill mine of U.S. Borax in Southeastern Alaska. To assure the regulatory agencies and the public of the viability and acceptability of this option, U.S. Borax undertook an extensive program of environmental studies aimed at assessing the impact of marine tailings disposal. This program was part of the feasibility and environmental permitting studies conducted by Bechtel Civil & Minerals, Inc, on behalf of U.S. Borax. Due to the unique nature of the proposed tailings disposal system, a Board of Consultants was established. The Board assisted in planning the modeling and field program and reviewed ongoing work. This paper outlines the basic elements of the marine tailings disposal study program which can be viewed as a prototype for similar studies elsewhere. Background The Quartz Hill molybdenum deposit is located on a knoll in an elevated valley in a mountainous region of southeast Alaska, about 45 miles east of Ketchikan (Figure 1).

Jan 1, 1986

By M. Younis, E. Comis

"The success of a tunnel project relies on many factors, but one of the most important is also the most overlooked: coordination by all parties involved during the design stages. This is particularly true of segment design and TBM design. Tunnel lining with segmental rings is usually designed according to the standards of reinforced concrete construction based on a given GBR. However, for TBM tunneling, the determination of loads during ring erection, advance of the TBM, earth pressure, and bedding of the articulated ring are all part of the tunnel lining design as well. TBM design can be heavily affected by the segment arrangement, dimension, and weight, but these are usually given as a fixed input to the TBM manufacturer—a process that can cause unnecessary complications. The authors propose that the industry evaluate the process as it stands. In order to find the optimum balance between lining design and TBM cost and operational workflow, both designs should be finalized concurrently. This requires coordination between the TBM manufacturer and segment designer from the early stages. The aim of this paper is to evaluate the influence of the segment lining design on TBM cost and performance, and to provide commentary on existing design guidelines to optimize lining and TBM procurement. INTRODUCTION The conventional project setup for tunnel lining design and the design and manufacture of the tunnel boring machine (TBM) should be coordinated in a timelier manner. It is widely acknowledged that the design of segments must consider the forces exerted by TBM rams during tunnel construction, but other inputs are most frequently provided to the TBM manufacturer as fixed parameters to design around. This paper describes other important factors in TBM design that impact not only the interaction with the segments, but also the construction of the tunnel in terms of overall production and even safety. For example, the segment width and tapering have direct influence on shield body length and thrust cylinder size. Furthermore, TBM geometry can also affect the backup (trailing gear) layout and length."

Jan 1, 2016

By Garland R. Dever

Limestone resources for industrial, constructional, and agricultural uses occur on the surface and at minable depths in several areas along the Ohio River and its navigable tributaries in Kentucky. Operable thicknesses of high-calcium and high-carbonate limestones suitable for use in cement and lime production, steel manufacture, environmental-control measures, and other special uses are documented in Ordovician and Mississippian formations by analysis of 0.3-meter (foot-by-foot) samples. Active and potential mine and quarry sites afford access to water transportation and proximity to a number of industrial and metropolitan centers. Geologic factors affecting the distribution of deposits include the Cincinnati arch, regional dip into the Appalachian and Eastern Interior basins, complex faulting in and near the Western Kentucky fluorspar mining district, and late Paleozoic erosional unconformities in northeastern Kentucky.

Jan 1, 1977

By R. J. Sheets

In 2009 the Gold Quarry open pit mine, located 11 km northwest of Carlin, Nevada, USA, experienced multiple large-scale slope instabilities of the upper east highwall that reduced gold ore extraction for nearly 18 months. The slope instabilities occurred within a weak, consolidated sedimentary sequence that exhibits strength characteristics that are transitional between soil and rock. Instability initiated as mining exposed the lower clay-rich sub-units of the Carlin Formation (Fm.). This deformation created preferential flow paths that allowed groundwater from the upper sandy sub-units to infiltrate low permeability clay-rich sub-units, thereby enhancing deformation of the slope toe which in turn destabilized the upper portion of the highwall. The outcome was a 160 m high slope instability that had a lateral run-out of 850 m. The effort to return the pit to ore production required both the geotechnical and hydrogeological investigations and the preliminary remediation mining activity to be concurrent. This approach required the development of detailed safety procedures and a requirement to modify the remediation design as new results were obtained. An initial challenge was to mitigate a near vertical, 90 m headscarp with blast induced, localized slope failures. Back-analyses applying numerical modeling indicated that the failure surface did not coincide with initial interpretations based on field observations; drilling results eventually confirmed this alternative failure geometry. The final remediation design incorporated shallower slope geometries and an approximately 3 Mt buttress along the base of the Carlin Formation and bedrock contact to reinforce the lower clay-rich sub-units. The outcome is a stable highwall within the Carlin Fm. following nearly ten years of repeated slope instability, and an example of the necessity to conduct appropriate geotechnical and hydrogeological studies during the early stages of a new layback evaluation or new open pit development.

Feb 23, 2014

By J. Sidhom, W. Fourie

"As the mining industry continues to face difficult challenges the need to persistently focus on productivity and utilization of labor and equipment costs will intensify. With these challenges in mind, Joy Global is helping to bring mining performance and analytics to the next level. By evaluating underground haulage, a significant component of the Room and Pillar mining value stream, variables have been identified and sensitivities have been performed to show opportunities to balance and streamline throughput. As a result of applying operational excellence tools to the mining environment, Joy Global is seeking to optimize mining performances by limiting waste, simplifying the process, increasing productivity and machine utilization, as well as removing workers from harm’s way. These days it’s not enough to work harder; mines have to work smarter. Improving efficiency, reducing costs, increasing safety: these are no longer ‘nice to haves’, they are ‘must haves’. Starting with the best products and the right people is a first step, but then what? How do mines take their operations from just OK to being a top performer? By using operational excellence principles aimed at eliminating waste, simplifying processes, automating where possible and removing people from harm’s way. The fundamentals of operational excellence (OpEx) are based upon the DMAIC process, which stands for define, measure, analyze, improve and control. DMAIC is an improvement cycle that helps with, for example, haulage optimization by: defining the issues and problems in the process as well as the areas of improvement; measuring and collecting mining operational data by time study and equipment monitoring system; analyzing through sensitivities and production modelling to determine root causes; then improving the performance and controlling the operation. Joy Global uses Joy OpEx or ‘lean’ principles inside its organization to drive efficiency, but it also helps its customers employ them to achieve new levels of productivity and safety. These same principles can be applied in most situations to streamline processes, improve operations and deliver value. As applied to mining, OpEx is seen as moving the needle on value creation by first identifying the value stream, then analyzing the areas that are not optimized. Once defined, these areas are ‘designed out’ of operational processes to create an automated operational flow. At a US coal mine, Joy Global was brought in to apply Joy OpEx principles to optimize mining and haulage to improve productivity and reduce costs. This multi-phase process started by defining the existing systems challenges to start finding areas for improvement."

Jan 1, 2017

By George Hufford

An investigation is made into the applicability of queueing theory to simulating the operation of a large open pit copper mine in the southwestern United States. Actual data from a working mine was used to construct curves for truck loading time, haulage and return time, and dumping times. Known results of investigations of queueing models (Koenigsberg - 1958, Gordon and Newell - 1967, Cabera and Maher - 1973) were used to simulate the actual operation. These did not give acceptable results so commonly used probability distributions were fitted to the actual data. A large computer program known as Q-GERT was used with the various parameters obtained from fitting the curves. Kolmogorov- Smirnov tests were run that showed that this was not satisfactory either. Finally, Q-GERT was used with the actual data from the mine. An appropriate correction factor is then found to apply to the exponential probability distributions tested previously and satisfactory results are obtained.

Jan 1, 1981

By Amy McBrayer, Andrea Brickey

The paper discusses the mine planning methods used in the Powder River Basin (PRB), highlighting the differences from open-pit metal mines. It emphasizes the need for agile mine operations due to changing commodity markets and the challenges faced by the coal industry, such as volatile prices and reduced engineering manpower. The study includes a survey of mine engineers to document current practices and identify potential improvements.

Sep 1, 2023

By R. V. Stewart

This chrysotile asbestos orebody is located near the northern tip of the Province of Quebec, Canada. It is some 1818 km (1130 mi) north of Montreal; 480 km (300 mi) north of the tree line and is situated within the zone of continuous permafrost. The open pit ore zone is approximately 0.4 km (1/4 mi) in length some 61 m (200 ft) in width and plunges at 25-30 below surface to a vertical depth of at least 610 m (2000 ft). The orebody was originally evaluated by programs of surface mapping, diamond drilling and bulk sampling. The fibre is semi-crude, possesses excellent strength, and good fibre length distribution.

Jan 1, 1978