Search Documents

By Jerry C. Tien

China?s remarkable levels of economic growth during the past three decades have lifted almost 300 million people out of poverty. This amazing achievement has placed an increasing demand on energy and minerals, especially coal, which supplies 68.7 percent of China?s energy (June 2011). It is estimated that China mined more than 3 Gt (3.3 billion st) of coal in 2010, three times as much when compared to merely 10 years earlier. Such an impressive achievement does not come without major costs ?? including concerns with mine safety and an increasing number of occupational illnesses due to fast growth. This article reports on one of the major safety concerns in China?s coal mining, dust and dust control practices, and known cases of caol worker?s pneumoconiosis affiliated with prolonged exposure to excessive coal dusts. The exact size of China?s mining industry is not known, but it is estimated the coal industry is at least five-million people strong, and the metal and nonmetals industry probably employs another three million people. To meet increasing energy demand, China mined more than 3.1 Gt (3.4 billion st) of coal in 2010 from its 15,000 plus coal operations1, most of which are small- to medium-sized operations with annual coal productions ranging from a few thousand tons to 300 kt (330,000 st). These small coal operations are typically in remote areas, inadequately engineered, poorly ventilated and still using rudimentary drilling and blasting mining methods employing antiquated mining equipment and, presenting safety concerns, i.e., methane and dust explosions.

Jan 1, 2011

By Antoon W. van der Vooren, Colin R. Phillips

A comparison of analytical models used to describe deposition in the first generation of lung bifurcations is presented. In order to allow testing of the mathematical models, experimental data were obtained from radon daughter deposition in simplified lung bifurcations. The experimental data for particles deposited by diffusional mechanisms is best described by the assumption of a thin concentration boundary layer at the entrance of a right circular tube. Other more complex models do not accurately describe the deposition of submicron particles. The angle of bifurcation was found to have a minor effect on deposition.

Jan 1, 1981

By George M. Hamilton

The gas producer actually dates back far beyond the period from which we first find recorded data. A partial production of producer gas can take place in any type of solid fuel grate equipment, such as a boiler, or even a fireplace if a sufficiently deep fuel bed is provided. Those of us who have watched a coal fire burning in the hearth, have no doubt noticed at times, the gases liberated by the heat burning on or near the surface of the fuel bed. So far as we know, the first gas producer was built by Bischof in Germany in 1839, followed by Ebelman in France in 1840, and Ekman of Sweden in 1845. The first large industrial development in the use of gas producers was When the two Siemens brothers of Germany patented their first combined gas producer and regenerative furnace in 1861, thus opening up the field for the use of raw, crude producer gas in heavy furnace work. In the years 1879-1881 J, E, Dowson, of England developed a producer gas cooling and cleaning plant, which extended the scope of application of producer gas to make possible its use in small furnaces and gas engines.

Jan 1, 1961

By Richard H. Kennedy, G. A. Swanquist, John W. King, Frank F. McGinley, Dale C. Mathews, Hans H. Adler, E. C. Peterson, Ralph M. Wilde

INTRODUCTION From the first historical records of the discovery of uranium as an element and the attempted classification of its minerals in the early 18th century-through its first uses in pigmentation and the coloring of glasses and ceramic glazes-until 1939 when it was discovered that the isotope U235, was fissionable, uranium oxide in the form of pitchblende ores and concentrates (produced mainly in Bohemia, Canada, and the former Belgian Congo) in recent times was the source of uranium compounds incidental as byproducts to the recovery of radium from this invariable associated source. In 1938 this byproduct production from pitchblende concentrates was about 471 st of U3O8, with over 90% from Canada and the Belgian Congo and only 25.85 st from carnotite ores in the United States.1 Under the impetus of the Atomic Energy Commission's (AEC now part of the Energy Research Development Administration) domestic and foreign production incentives and buying programs, and as an initial assurance of atomic armament capability of the United States and the Free World, the growth of the uranium mining and milling industry burgeoned from 1952 to 1962. After a short period of decline, in the second decade and in large commitments beyond, it has again extended its capacity to meet ever-increasing fuel demands of atomic power generation by the electric utilities industry. In 1961 the peak production in the United States alone was 17,758 st of U3O8. Peak aggregate domestic and foreign deliveries of 34,581 st of U3O8 to the AEC occurred in 1960.z Canada's maximum delivery of 13,506 st of U308 was made in 1959. These peak and continued productions in the Free World are largely from: the Mesozoic (Jurassic) and Tertiary (Eocene) sandstones in the United States; the quartz pebble conglomerates of Canada and the Witwatersrand; pegmatites, Jurassic limestones, and Precambrian complexes, with less but significant production; the phosphoria, where byproduct production is minor. This uranium production in the form of precipitated concentrates has come from the milling of ores from these sources, both directly and by retreatment of gold cyanidation tailings on the Witwatersrand. Milling of crude ore has followed these processes: conventional crushing and size preparation, ore drying when required, salt roasting for high vanadium ores and byproduct vanadium recovery, carbonate or acid-leaching processes, classification sand-dine separations or countercurrent decantation (CCD) circuits and complete liquid-solids separations, resin-in-pulp (RIP) or liquid-liquid (solvent) ion-ex- change extractions, clarification of pregnant liquors, precipitation, filtration and washing, sodium and vanadium removals, and drying or roasting and packaging of the high-grade, high-purity uranium concentrate commonly referred to as "yellowcake." Coupled with the hazards and control of dust generation incident to conventional crushing and milling operations, more stringent control of airborne respirable and ingestible radioactive particulates and the protection of personnel against definitive external radiation are inherent to uranium milling. Impoundment and control of tailings and other effluents of uranium milling are more restrictive than in conventional practice, be- cause long-term disposal and containment of the uranium series of radionuclides, whether in solution or in solid form, are requisite to uranium milling and are made manadatory under regulatory agencies of government. 2. GEOLOGY AND MINERALOGY OF URANIUM Early Uses and Byproduct Production of Uranium Uranium was discovered by Klaproth in 1789 but had little commercial importance until the discovery of uranium fission by Hahn and Strassman at the close of 1938. The well-known uranium ores of Joachimsthal, Czechoslovakia, the Congo, and the Colorado Plateau were early sources of radium. Minor quantities of uranium were used for small-scale technical and industrial applications, particularly in coloring glass and ceramics, but most of the uranium was discarded. The Colorado ores were also mined later, chiefly for vanadium. Impetus of Armament Capability and Fuel Demands for Atomic Power Following the discovery of atomic fission, uranium became critically important for military applications and, more recently, as a nuclear fuel. Prior to 1966 uranium was acquired in the United States almost solely for use in the weapons program of the AEC. By 1970 the AEC had procured approximately 325,000 st of U3O8 from domestic and foreign sources. Current and future marketability is primarily dependent upon commercial demand for reactor fuel. Estimates of

Jan 1, 1985

By J. W. Langford

A more effective method of fracturing and chipping the formation is necessary to significantly increase the productivity of blasthole drilling with a roller cone bit. The conventional rotary blasthole bit engages the formation and initiates spalls, chipping and fractures in the formation at a rate dependent on the amount of pull down force applied by the drill. The rotary speed of the drill increases the number of fractures and creates drilled chips that are removed from the hole by the air circulation. An engineering project was motivated to develop a low pressure, low impact downhole percussion hammer to provide an overstrike force to a blasthole bit, in addition to the conventional pull down force and rotary speed. The objective of the project was to utilize existing rig air packages in the range of 50-110 psig and provide an overstrike force to the bit in the range of 1100-1500 impacts per minute. Laboratory testing performed on Barre granite achieved, on average, a 40% improvement in rate of penetration. This performance has been confirmed in actual blasthole drilling in copper and iron ores mines. During the testing phase, additional unexpected benefits have also been realized.

Jan 1, 2011

By Marc Lemieux

A new moving cone optimizing technique will be introduced. In order to facilitate under- standing of the moving cone optimizer, a re- view of the principles of moving cone design technique is presented. A concept called the negative moving cone design technique is also introduced to help facilitate understanding of the moving cone optimizing algorithm. In the introduction to Subsection 3.3, the relationship of the mineral inventory modeling technique to the ultimate pit design optimization methods was reviewed. Five modeling techniques were described, and four mathematically provable optimizing methods discussed. The broad use of the regular 3D fixed block model was attributed, in part, to its applicability to automatic optimization methods of pit limit design such as the Lerchs-Grossman graph theory algorithm, and in part, to its systematic nature.

Jan 1, 1979

Despite the current economic downturn that is now decimating iron ore production, Minnesota?s mining operators remain optimistic about the long-term prospects for the industry. Reflecting this optimism, the development of several new mining projects continues in the state. The future of mining in Minnesota was the featured topic at the combined 82nd Annual Minnesota Section of SME Meeting and 70th Annual University of Minnesota Mining Symposium. More than 500 mining industry professionals, including engineers, executives, mining managers and equipment suppliers from the around the world, attended the meeting, which was held April 14 and 15, 2009, in Duluth, MN. The combined meeting featured a keynote session with three distinguished speakers plus a panel discussion by representatives from several of Minnesota?s taconite producers. The keynote speakers were Curtis Clark, president and chief operating officer, Behr Dolbear, who gave a presentation on the ?State of the Mining Industry.? Phil Newman, chief operating officer, CRU Strategies, spoke about challenges facing the mining industry and James A. Skurla, acting director, Bureau of Business and Economic Research, Labovitz School of Business and Economics, University of Minnesota Duluth, discussed the importance of mining to northeastern Minnesota?s economy. The taconite producers panel discussion included Jonathan Holmes, vice president and operations manager, ArcelorMittal; Ed Latendresse, vice president and general manger, Hibbing Taconite; John Tuomi, vice president operations services, United Taconite and Mike Mliner, vice president and general manager, Northshore Mining. The mangers provided updates on their respective operation The meeting included concurrent technical papers sessions on mining, processing, environmental and nonferrous mining. The sessions included technical papers that provided information on the status of a number of new mining projects in the state. The conference also offered a SME short course titled ?The basics of iron mining.? A tradeshow that featured about 100 companies and organizations offering products and services to Minnesota?s mining industry ran in conjunction to the conference. It was estimated that more than 900 people, including conference registrants and special invited guests of the vendors, attended the tradeshow opening reception. This was the largest trade show in many years. The Minnesota Section of SME also held its annual business meeting during the conference.

Jan 1, 2009

By B. Stewart

Recent ore pass failures have underlined the need for improved designs, standards, structural monitoring methods, and better hang up prevention and removal techniques. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) are investigating methods to improve safety during transport of ore in ore passes. Design criteria and hang-up prevention and remediation strategies involve studies of the effects of static and dynamic ore and waste rock loads on chutes, walls, gates, and support structures. Particle flow analysis methods were used to simulate the response of various ore pass designs to a wide range of ore loading conditions. A full-scale mock-up of actual ore pass and chute assemblies was duplicated and tested for load response. Data from a particle flow code and the mock-ups were com-pared. Loads on an active ore pass chute were measured.

Jan 1, 1998

By Jean-Michel Rendu

In most mining operations, some degree of selectivity is applied. Whether one deals with surface or underground operation, ore zones, and waste zones are defined not only on the basis of the value of the ore contained, but also taking mining constraints into account. A number of computer techniques are presented which can be used to determine the optimum location of the footwall and hanging wall of ore zones intersected by drill holes. Minimum mining width and minimum internal waste width constraints are taken into account, as well as other economic constraints. The system is presented as an integral part of a larger manumatic ore reserve and mine planning system.

Jan 1, 1982

By Davar Abi-Zadeh, Cillian Brown, Deepak Kandra

"Grout backfill strategy for a particular subsurface concrete tunnel (~4.9km long, 3.5m in diameter, carrying 20” gas pipeline) was based on achieving 1:100 slope of the fill in order to progressively fill the tunnel, in a series of 350m section. Grout rheology, particularly its non-Newtonian and thixotropic behavior, determines the final fill slope for given backfill strategy. The objective of this study was to simulate the two-phase grout mix backfill process using Computational Fluid Dynamics (CFD) and determine the slope of the fill to validate and optimize the backfill strategy. Three dimensional CFD study showed that for a 500m long tunnel section with a single injection point of grout, given its rheology, it will likely keep flowing without filling the 500m section height wise. Design optimization for filling was carried out using two dimensional studies to make the backfill process “slope independent” by incorporating a 2.5m high bulkhead at ~1,000m. INTRODUCTION As part of a gas field development a 20” onshore gas pipeline is required from the landfall site to the processing terminal some 8km inland. At the landfall site the gas pipeline is routed in a ~5km underground tunnel underneath a bay. For operational reasons and planning consents as well as to mitigate environmental impact based on an environmental impact study, once the gas pipeline and the associated services and spares have been installed, the subsurface gas tunnel will be fully grouted. There will be no permanent access to the tunnel after construction is completed and the site compounds have been reinstated once works are complete. One of the key requirements is that “full grouting of the tunnel” is desired. The grouting material used is a non-Newtonian and thixotropic fluid mixture of bentonite, cement, plasticizer, retarder/stabilizer and water. The tunnel is filled progressively in 350m sections using a combination of existing and new pipework assuming the grout rheology will yield a fill slope of 1:100 in a 350m section. The proposed grouting system used one pump at the grouting compound to pump the grout into the tunnel using the existing tunneling pipework. For the longer runs a second booster pump was used in series to pump the grout to its final discharge location. The filling process is controlled via a system of flow meters, pressure transmitters and a tunnel CCTV system."

Jan 1, 2016

By Gregory P. White

A number of private companies and universities have developed computer programs which can be used to simulate surface coal mining by dragline. In this paper, we briefly discuss the concept of computer simulation, compare these computer programs with each other, describe the major changes required to convert these programs to an IBM computer system, and analyze their sensitivity to inaccurate input data. We also present a summary of the required data input for each program, core storage requirements, and output results. Sources for obtaining these programs and their documentation are listed at the end of the paper.

Jan 1, 1983

By N. Merriam

This report describes Koppelman's work to develop the K-Fuel® Series C Process used to dry and stabilize Powder River Basin coal. It also contains summaries of the results of bench-scale and pilot plant tests conducted to prove the Series C Process. The process is being used by the KFx-Thermo Ecotek partnership for a 500,000 ton per year commercial plant that has been constructed near Gillette, Wyoming. The plant is presently undergoing shakedown.

Jan 1, 1997

By Donald P. Schlick

Gentlemen, today I would like to talk to you about metal and nonmetal mine health and safety--past, present and future. Briefly, I will comment on the past because it is important to an understanding of our present activity and our plans for the future. Federal inspection of noncoal mines was not authorized until 1966, when congress passed the federal metal and nonmetal mine health and safety act; public law 89-577, with the passage of this act, the federal inspector, for the first time, had the delegated authority and responsibility to enforce health and safety regulations designed to prevent personal injuries and occupational diseases, the new law also provided for the education and training of our miners; assistance to the operator through the transmission of technical and scientific information and assistance and equally important, the law made provision for state participation in the congressional mandate to prevent injuries and save lives in the mineral industry, Before I tell you about our program and our future plans, I want you to know that I am here to listen as well as to talk! In my view, the only kind of communication that is meaningful is two-way communication. Our nationwide progress in metal and nonmetal mine health and safety during 1972 cannot be measured in reduced fatalities or injuries. The unforeseen tragedy that took pace in Kellogg, Idaho, in may of last year mode that almost a certainty.

Jan 1, 1973

By D. M. Neil

Road-headers are one of the most popular mechanized excavators used in mining and civil under-ground construction. These machines are primarily used in soft to medium hard rocks. This paper reviews the parameters associated with the application and operation of road-headers and presents a method for estimating cutting performance.

Jan 1, 1994

By H. E. Rudi

The advent of open nit mining permitted the development and processing of minerals never before thought possible. New equipment was needed; new techniques were devised; new methods were called for. This development and acquisition of new techniques, methods and equipment did not, however, stir the souls of our industry and educational leaders sufficiently to a recognition of the problem of people, especially the future development of the people needed in open-pit mining. The people problem has been and will be with us as long as there are two of them. The development of people will be required for the same reason. The problem of developing future personnel for open-pit mining is not what must be developed; that is known to all of us and can be briefly stated ashore and better of everything." As I see it, the real problem lies in determining (1) what personnel are really critical, (2) why are they critical and (3) how can we develop them.

Jan 1, 1965

By H. B. Oblad

The WEMCO® SmartCell™ flotation machine is a continuously-stirred tank reactor in which solids are suspended in water and are contacted with air. The reaction is particle flotation resulting in the separation of valuable material from gangue. The effects of several operating variables on the flows of water and air and on motor power were measured. A miniature magnetic flowmeter was installed in the draft tube that allowed measurement of the water flows into the rotor. This work has led to a better understanding of machine function which will lead to improved performance and better operation. General equations for optimization, design, and scale-up were inferred.

Jan 1, 2002

By K. Boakye, T. Newman, P. Bláha, M. B. Toelle

"This paper presents a quarry optimization plan using a block model and an in-house development quarry scheduling and optimization software (QSO Expert) to help improve quarry operations at Crystal River. The Crystal River Quarry is an underwater quarrying operation that barges limestone via the Gulf of Mexico, as the main source of raw material to a cement plant in Theodore, Alabama. To improve the quarry operation, an evaluation was completed to optimize the quarry planning and extraction procedures of the quarry. In order to achieve this, additional exploration drilling campaign was implemented, a new block model was re-calculated and the latest version of QSO Expert software was used. The primary economic impact is a higher recovery of limestone reserves; sustainability of resources, corresponding longer quarry life. Secondarily as the limestone is mined underwater and stockpiled above water, drainage reduces moisture content achieving direct cost reduction on limestone shipping. In addition, a considerable reduction in operational cost was achieved due to a significant decrease in consumption of electrical energy, reduced dragline maintenance costs and reduced dragline movements within the operation. INTRODUCTION Holcim is a Swiss-based global building materials and aggregates company. Founded in 1912, the company expanded into France and then throughout Europe and Middle East during the 1920s. In 1922, Holderbank, as the company was then known, expanded beyond the Swiss borders into France. By the end of the decade Holderbank held stakes in Belgium, Germany, the Netherlands, and Egypt (Holcim History 1912-2012) Positions in Lebanon and South Africa soon followed.. Holder bank later expanded in North America in the 1950’s. In the late 1970s and early 1980s, Holderbank continued its expansion in Latin America, Asia and Spain for the first time. The company expanded into Eastern Europe and experienced a boom in Spanish construction preceding the 1992 Summer Olympics. By 1986, Holderbank was the world's largest cement manufacturer. In the 1990s, the company consolidated its European holdings as the American market drove growth. Expansion into Eastern Europe and Russia continued (Holcim History 1912-2012). In 2001, the company changed its name from ""Holderbank Financière Glaris"" to Holcim (short for Holderbank ciment) (Holcim History 1912-2012). Holcim expanded by purchasing Aggregate Industries entering into the United Kingdom for the first time. That year, the company also expanded into India by acquiring a stakes in The Associated Cement Companies (ACC) and Ambuja Cement Eastern. In 2008, Holcim became the largest shareholder of China's Huaxin Cement with a 40% stake. In 2009, they acquired Cemex Australia. In 2014, Holcim and Lafarge announced they had agreed to terms on a ""merger of equals"" valued at nearly $50 billion in 2015. The new company LafargeHolcim based in Switzerland has a manufacturing capacity of 427 metric million tons a year."

Jan 1, 2017

By Peter J. Lawson, John A. Rideout, Gregory W. Dicinoski

A considerable body of literature directed towards optimising the efficiency of gold and silver extraction from cyanide leach liquors has appeared in recent years. A few examples from dissolution to solvent extraction to adsorption in carbon-in-pulp (CIP) and resin-in-pulp (RIP) operations follow. Selective leaching of gold from copper-gold ores using ammonia-cyanide mixtures extends the % copper which may be tolerated in ores (Ruane, 1991, LaBrooy et al., 1991, Costello, 1991). The removal of copper and recycling of cyanide from high copper ores is another important development (Sceresini and Staunton, 1991). Solvent extraction of alkaline cyanide liquors (Riveros, 1990, Mooiman & Miller, 1991) and solvent aided elution in CIP (Muir, et al., 1985) look promising. Recent definitive papers on the mechanism of adsorption of aurocyanide by activated carbon should lead to more efficient use of CIP (Adams and Fleming, 1989, Klauber, 1991). Strong and mixed weak-strong base resins have been applied in RIP for aurocyanide extraction in Russian Plants since the 1970's (see for example Borovskii et al., 1985, and references cited in Fleming, 1988a). Fundamental studies on applications of commercial weak and strong base resins-in-pulp (Fleming & Cromberge, 1984a, b, Fleming 1988a, Hosking 1984, Riveros and Cooper 1987) have generated much interest in RIP. Detailed comparisons of CIP vs RIP efficiencies at Mintek in South Africa (Fleming et al., 1988b), and the inefficiency of CIP in contact with clay led to the commissioning of the strong base RIP Golden Jubilee plant in 1988. Its operation and improvements have been reported (Seymore and Fleming, 1989, Fleming & Seymore, 1990). The use of anion exchange membranes for aurocyanide extraction shows some promise (Mauthoor et al., 1991). However, the development of new gold specific resins at Mintek (Green et al., 1984, 1986, 1990, Johns and Green, 1991) and elsewhere (Asker et al., 1987, Wilson et al., 1987, Harris et al., 1992) should improve the viability of RIP processes. The polydiallylamine gold specific resins (Hodgkin & Eibl, 1988, Fawell et al., 1992a, b) have high capacities for auro cyanide recovery from high concentration liquors. The use of guanidine based liquid and solid ion exchange extractants for gold was recently reported by the Henkel Corporation (Kordosky., et. al., 1993). Such specific resins tailor made for gold and/or silver cyanide extraction should lower overall cost by improving metallurgical efficiency. In the case of strong base resins this selectivity largely eliminates the problems of poor base metal elution and/or poisoning. The work reported here outlines the approach taken at the University of Central Queensland to synthesize sterically hindered strong base anion exchange resins which are designed to have high selectivity for auro- and argentocyanide complexes. It summarises selectivity tests on low grade cyanide leach liquors from several mines. It also examines an RIP vs CIP comparison, and investigates the elution properties and cycling of one such promising resin.

Jan 1, 1993

By Dan Nilsson

Open pit mining is the strong sector of the American mining industry. In the middle of the 60's. 17-18% of the ore in metal mines was mined with underground methods. From the middle of the 60's to 1980 the production in open pit metallic mines increased from about 400 to close to 600 million short tons while at the same time the underground mine production decreased a little, from about 90 to about 80 million tons. Less than 15% of the ore prodction now come from underground mines. Large amounts of waste rock were also handled in the open pits. In the middle of the 60's about 600 milion tons were handled, in 1980 1,200 million tons were moved. This means that the average stripping ratio increased from about 1.5 to over 2.0 tons of waste rock per ton of ore, figure 1.

Jan 1, 1983

By V. Svalbonas

When the Trelleborg Divisions of Boliden Allis and MPSI merged, a unique opportunity occurred for two independent mill fabricators to compare various design procedures and the research upon which they were based. This paper documents such a comparison in the structural design area. Several SAG mill analyses are compared using both Boliden Allis and MPSI methods. The differences and similarities are then utilized in a correlation of critical stress definitions and the acceptable design and inspection criteria.

Jan 1, 1992