Search Documents

By Jingzhi Liu, Xueping Hu, Huai Wang, Simin Yang, Baoqiang Yu, Deguang Zhan

In this study, response surface methodology (RSM) and Box-Behnken design to improve copper extraction from refractory copper oxide ore were investigated. Based on single factor tests, quadratic polynomial equation to describe the relationship between influencing factors (particle size, leaching temperature, sulfuric acid concentration, leaching time) and copper leaching rate could be obtained by RSM. The optimum parameters determined by the model are as follows: particle size 64.60% − 74 μm, leaching temperature 74.15 °C, sulfuric acid concentration 0.49 mol/L, and leaching time 140.85 min. Under these conditions, experimental copper leaching rate of 85.12% could be achieved, which was very close to the predicted maximum value (85.34%) by the model, indicating the quadratic polynomial model was accurate and reliable. Copper leaching rate increased approximately by five percentage points comparing to the result of single factor tests. This study indicates that response surface methodology is an effective method to optimize experiment conditions and achieve an ideal experiment result.

Aug 17, 2022

By M. David Monroe

Getting the best match between truck and haul road requires examining the cost effects of many factors. Most mines use a bottom line measure based on cost per ton of material moved. This measure focuses on the two components of truck haulage cost per ton: productivity (or performance) and operating cost. For specific tasks, productivity can be measured or predicted using either field measurement or modeling. Individual tasks can be combined to provide a larger scale, longer term net figure for total mine output. True cost is more difficult to capture. Factors are time- and task-oriented and can be influenced by a summation of factors over a truck's lifetime. For example, "allocated" costs, such as owning (depreciation) and some repair costs, are spread over long periods. Items such as fuel and tires can be tied more directly to certain tasks. This article focuses on the more direct, task-oriented factors that affect truck productivity and cost. Major factors The relationship of haul roads and trucks means that each must be examined separately to isolate the most important factors affecting performance and cost. There are many factors but the most important are:

Jan 1, 1992

By William G. Pariseau

The purpose of this paper is to present a discussion of the various approaches that can be utilized in the study of mine subsidence phenomena. Attention is focused upon the rational selection and use of laboratory models. Broadly interpreted, mine subsidence is the deformation of the rock mass enclosing the mine. Depending upon a number of factors, the movement of the subsiding rock mass may be such as to disrupt gas and water lines or other buried utilities, to damage surface structures such as buildings and bridges, to dislocate streams, roads, and rail lines, to aggravate acid mine drainage and fire problems, and to generally mar the landscape. It is clearly a problem that no mine manager can safely ignore. It is also a problem that will grow with the general population increase. In the following, a summary review of past and present approaches to subsidence studies is given. The possibilities of duplicating subsidence phenomena in laboratory models are examined, and an analysis of a particular type of model is presented. Some preliminary results obtained from a model of the particular type analyzed are then discussed.

Jan 1, 1968

By Knezicek Zeljko, Knezicek Tihomir

Lignite open cast mine "Dubrave" is the largest lignite mine in Bosnia and Herzegovina. The open cast mine was designed with two external waste dumps. Waste dump "West" is the major dump, while "Cajici" dump is used for dumping waste taken from leveling the terrain. The major waste dump contains 14.6 million cu.m. of waste, while the side waste dump contains 3 million cu.m. of waste. Existing situation with available sites for depositing the waste shows that additional space for dumping the waste must be provided. Three options can be taken into consideration. The fact is that none of the three options are suitable for the current production situation. This article deals with the optimization process for obtaining the optimal variant where a waste dump can be located and selection of the most valuable option.

Jan 1, 2002

By R. Hogg

Based on a simplified model for the motion of particulate materials in horizontal, rotating cylinders, approximate expressions have been derived relating the power consumption of a tumbling mill to its dimensions and speed of rotation and to the amount and nature of the charge. The basic assumptions underlying the model are that there is no slip between the charge and the mill shell, that the free surface of the charge remains essentially planar during rotation and that there is no transfer of momentum from the material flowing down the free surface back to the mill shell. The relationships formulated from this model have been shown to be in excellent agreement with experimental results taken from the literature. While the requirements of the model are most closer met at low speeds of rotation, the results appear to be valid even for speeds up to 70-80 percent of the critical speed. Poorer agreement between theory and experiment is found when the charge consists of relatively large particles (balls) and when the filling of the mill exceeds 50 percent of the available volume. Qualitative explanations of these deviations have been offered.

Jan 1, 1971

By Mark E. Emerson

Foreign and domestic companies find the mineral potential of this country's stern public lands, its capital markets, political stability, and "open-door" policy attractive for hard mineral exploration. Traditionally, exploration in the US has been geographically based and responsibility oriented at the district level. The 1970s brought a decentralized approach to exploration as major non-metal companies began to diversify into hard minerals. The emphasis was on capital intensive metal and energy projects involving bulk-tonnages. The recent economic downturn in metals has caused many of the new participants to withdraw from the mineral scene. The surviving companies have shifted their emphasis toward medium scale precious metal projects having high operating margins and rapid return on equity. Exploration expenditures in the United States are now principally focused on gold and silver to the exclusion of practically all other commodities. In the search for precious metals companies have scaled back their exploration efforts and have began to apply new approaches to target selection. The search is being assisted by rapidly evolving conceptual models. The change in orientation has led to numerous new discoveries. The finds are essentially "rediscoveries" that c,-re previously uneconomic. The majority are low-grade surface deposits that have involved low discovery costs and short lead times for development by low-cost mining and beneficiation methods. The emphasis on gold to the exclusion of all other commodities raises questions regarding the direction of exploration in the US for the rest of the 80s.

Jan 1, 1984

By Charles T. Holland

INTRODUCTION Insofar as I am aware, the term rock mechanics was not in the English dictionary in 1930 when I started my graduate program at West Virginia University. Hence, I never thought that I was undertaking studies in rock mechanics when I undertook to write a thesis on the physical properties of West Virginia coal. In this case, the subject was primarily concerned with the compressive strength of coal, the elasticity of the coal, the physical weathering properties of the coal and its friability. These days investigations of rocks pertaining to such properties are included in the term "rock mechanics". Other than this aspect, the principle interest in this part of my program was that I became interested in the strength of coal from the standpoint of structural purposes, and also became cognizant of its elastic properties as well as its energy storing properties. This research also tied in with a remark that Professor Lawall made in a Mining Methods class in 1928 when he remarked that a peculiar thing was happening in the southern part of West Virginia, namely, in the Pocahontas coal field. His remarks were to the effect that pillars were blowing up in the mines and when asked why he replied the cause was not known. The failure of three-inch coal specimens, especially those in stronger coal, in non-hydraulic actuated testing machines was reminiscent of his description of those pillar bursts or bumps.

Jan 1, 1971

By J. Y. Hwang

Sands are utilized to make molds for metal castings in the foundry industry. Approximately a half ton of sand is disposed of for each ton of metal cast in this country. In Michigan, annual sand disposal amounts to about one million tons. A process has been developed in this study to reclaim sands from a steel foundry. Physical separations are utilized in conjunction with other operations (such as the removal of binder, metal, spruce, washes, etc.) to yield silica and chromite sands with desirable molding properties. Several different separation methods, including electrostatic, magnetic, and various gravitational approaches have been examined. Experimental results are presented. The applicabilities of these separation methods are discussed.

Jan 1, 1992

By Yuan Le, Dominic Reda, Vojtech Ernst Gall, Kurt Zeidler, Tomasz Kecerski

High Speed 2 (HS2) mandated that Building Information Modelling (BIM) processes be implemented during design and construction. Gall Zeidler Consultants (GZ) was responsible for developing the BIM Models for the portals, tunnels, and cross passages of the of the 16 km-long Chiltern twin-bore Tunnel. In addition, GZ developed the GBR for the Chiltern Tunnels and incorporated the relevant information into the Project’s BIM framework. This paper presents the implemented BIM framework, describes the modelling approach, and discusses the advantages and challenges of implementing BIM, particularly how BIM improved interface coordination and how BIM was used in feasibility assessments of different construction options.

Jun 13, 2023

By George R. Mitchell

It is a common observation that objects having, different; temperatures exchange energy by radiative transfer. The quantity of radiant energy emitted by an object is a definite function of its temperature. Therefore, a measurement of emitted radiation, by means of a calibrated radiometric instrument, provides a temperature measurement without contacting the emitting object. The physical laws describing radiant energy transfer and their application to remote temperature measurement form the substance of this paper. The energy radiated by bodies having temperatures up to 4000°C is largely in the infrared spectral region. The infrared spectral region is that part of the electro-magnetic spectrum having wavelengths longer than visible light and extending to the microwave region. The wave-lengths range from 0.7 micron (1 micron = 10-4 cm) to 1000 microns. In general, infrared radiometry deals, with the methods of measuring energy flux in the 1 to 15 micron region of the infrared spectrum.

Jan 1, 1960

The roasting process of copper concentrates containing variable quantities of arsenic in a fluidized bed regime was analyzed, considering the technical literature published on the topic in the last quarter century. Although emphasis has been given to the analysis in the fluidized bed regime, other processes have also been considered, under a reducing, neutral or oxidizing atmosphere. The kinetic mechanisms of roasting, as well as the models that have been applied or those likely to be used to explain the kinetics of arsenic removal, are analyzed. Regarding the kinetic mechanisms, those that have been applied to copper concentrates with both high and low arsenic content are included. The roasting kinetic model includes the kinetic data analysis techniques, general models, equations and an estimation of the conversion degree through dynamic, differential and integral methods, as well as particular models for mineralogical components, such as smelter dust and copper concentrates with low and high arsenic content.

May 1, 2012

By K. D. Dill, S. D. Rosenthal

"This project analyzed the efficiency of incorporating the use of directional drilling technology into coal overburden blasting. Directional drilling is currently in use in the petroleum industry and it is believed that it will be a valuable asset in the mining industry. This project has shown that directional drilling can be a viable technology for use in the coal overburden removal process resulting in increased drill utilization and potential for cost savings. Future work regarding blasting and geotechnical evaluation should be performed to solidify the concept. INTRODUCTION Determine the Potential Drill Utilization Improvements and Rock Fragmentation Requirements Using Directional Drilling in a Coal Mining Overburden Highwall Application was a project funded by Atlas Copco Drilling Solutions (Atlas Copco) based in Garland, Texas. The project was developed and researched by Montana Tech of the University of Montana. This project was intended to show how the use of directional drilling can increase drill utilization, while decreasing costs, without sacrificing overburden blasting results. This paper discusses a review of the literature, the methods performed, conclusions and future work Background Atlas Copco theorized that an alternative approach to drilling a cast blast pattern would be beneficial to coal mining operations by increasing drill utilization and therefore, decreasing overall costs. Increasing drill utilization results in an increase in the amount of time the drill is being productive, more drill bit time in ground. Atlas Copco’s theory is that by incorporating directional drilling in the design of a cast blast pattern, a drill rig could drill multiple directional holes, which are the length of the cast blast, from a single drill set up. A drill goes through a series of steps to complete a blast pattern, these steps include: tramming to the hole location, leveling the drill, drilling the hole, cleaning the hole, and retracting the drill steel. This process is repeated hundreds of times until the whole pattern is completed. The most time intensive part of this process is drilling out the blast pattern. Integrating directional drilling into this process could decrease the overall time it takes to drill out a blast pattern by minimizing the amount of time spent tramming and setting up for each subsequent hole. Tramming and drill set up are two aspects of the drilling process where the drill tool is not engaged with the ground and, therefore, not being utilized. A cast blast pattern designed to utilize directional drilling will allow the drill tool to be “in the hole” longer and will improve drill utilization. This change in drill utilization was analyzed. Drilling and blasting is an integral part of the mining process, without it mining would be a slower process and less material could be mined. Drilling provides holes for explosives to be loaded and then blasted. Blasting has been found to be the most cost effective method of fracturing rock in mining for material removal. Blasting is also used as a low-cost method to move the rock in open cast mines, commonly referred to as cast blasting. A cast blast is a large blast designed to allow for the maximum amount of overburden to be removed using explosives in a single blast thereby uncovering more coal at a lower cost. Not all the material is blasted to cast-to-final, which requires that material to be moved with large mining machinery. Material that is considered cast-to-final is material that has been thrown far enough to never be moved again in the coal extraction process, therefore it is in its final resting place. A typical cast profile and cast-to-final area is shown in Figure 1."

Jan 1, 2017

By S. K. Kawatra

In order to meet federal air pollution guidelines, it is necessary to remove a considerable quantity of sulfur from many North American coals. This may be accomplished by oxidizing the sulfur to water soluble forms, followed by washing the coal. Selective oxidation of the various sulfur forms can be accomplished through the use of a variety of types of bacteria. In this paper, the various bacteria and their requirements are described, and processes using bacteria to remove coal sulfur are discussed.

Jan 1, 1987

Despite the current economic downturn that is now decimating iron ore production, Minnesota?s mining operators remain optimistic about the long-term prospects for the industry. Reflecting this optimism, the development of several new mining projects continues in the state. The future of mining in Minnesota was the featured topic at the combined 82nd Annual Minnesota Section of SME Meeting and 70th Annual University of Minnesota Mining Symposium. More than 500 mining industry professionals, including engineers, executives, mining managers and equipment suppliers from the around the world, attended the meeting, which was held April 14 and 15, 2009, in Duluth, MN. The combined meeting featured a keynote session with three distinguished speakers plus a panel discussion by representatives from several of Minnesota?s taconite producers. The keynote speakers were Curtis Clark, president and chief operating officer, Behr Dolbear, who gave a presentation on the ?State of the Mining Industry.? Phil Newman, chief operating officer, CRU Strategies, spoke about challenges facing the mining industry and James A. Skurla, acting director, Bureau of Business and Economic Research, Labovitz School of Business and Economics, University of Minnesota Duluth, discussed the importance of mining to northeastern Minnesota?s economy. The taconite producers panel discussion included Jonathan Holmes, vice president and operations manager, ArcelorMittal; Ed Latendresse, vice president and general manger, Hibbing Taconite; John Tuomi, vice president operations services, United Taconite and Mike Mliner, vice president and general manager, Northshore Mining. The mangers provided updates on their respective operation The meeting included concurrent technical papers sessions on mining, processing, environmental and nonferrous mining. The sessions included technical papers that provided information on the status of a number of new mining projects in the state. The conference also offered a SME short course titled ?The basics of iron mining.? A tradeshow that featured about 100 companies and organizations offering products and services to Minnesota?s mining industry ran in conjunction to the conference. It was estimated that more than 900 people, including conference registrants and special invited guests of the vendors, attended the tradeshow opening reception. This was the largest trade show in many years. The Minnesota Section of SME also held its annual business meeting during the conference.

Jan 1, 2009

By L. G. Kirk

The Mississippi embayment ball clay region, including western Kentucky, western Tennessee, and northwestern Mississippi, accounted for more than 95% of the total U.S. ball clay production during 1985. Other producing states during the year were Texas and Maryland. The U.S. Bureau of Mines reported total domestic production for 1985 of 910,000 short tons. The United States exports approximately 20% of the annual ball clay production. Geologically, the ball clay deposits are sedimentary in origin and occupy the north- eastern flank of the Mississippi embayment. The commercial deposits have been confined to the Claiborne and Wilcox formations within mid to lower Eocene and upper Paleocene age strata. The deposits are lenticular in nature and highly variable in areal extent and thickness. They exhibit very abrupt lateral boundaries and are bounded laterally and vertically by unconsolidated sands, silts, and waste clays.

Jan 1, 1986

By R. H. Roberts

The Environment Weipa is located at 12° south latitude on the west coast of Cape York Peninsula, North Queensland, Australia. The climate is tropical with most of the 1 600 mm. average annual rainfall falling between November and March. During the short winter months (May/ August) the weather is clear and pleasant, with temperatures seldom exceeding 27°C.Throughout the remainder of the year, conditions are frequently oppressive due to consistent high ambient temperatures accompanied by high humidity. The terrain is of low relief, and generally not more than 6 to 10m. above mean sea level adjacent to the coast. The coastline features numerous short estuaries which discharge run-off from the heavy rains collected by creeks and rivers. The whole area is covered by an open forest, the predominant species of which is Eucalyptus tetradonta. These eucalypts have only limited commercial value and are heavily infested with termites. Despite the fact that Weipa is close to the location of the first reported sighting of the Australian coastline by a European (William Janz - 1606), it remains very isolated. There is no developed road or rail connection to centres of population, so that transport of practically all products, personnel and materials to and from Weipa is by sea and air. Cairns (population 49 000) is 580 km. by air and 670 nautical miles by sea; Brisbane, the

Jan 1, 1977

By J. A. Farinelli

In the Appalachian region of the United States, approximately 40% of the underground coal reserve base exists in seams 0.7 - 1.1m thick. These seams are, in general, often of premium quality and are frequently accessible through above-drainage drift-type openings. Unfortunately, there are no apparent advantages to mining thin seams, if quality is disregarded. The thin-seam mine is faced with the same legal and economic pressures as any other underground coal mine. But in addition to these common problems, thin-seam operations must also deal with the unique problems associated with mining at such a restrictive height. Small-scale, short-lived operations appear to be the most feasible means of mining these reserves. The purpose of this paper is to evaluate the production and safety potential of various thin-seam mining systems. Recommendations will be made regarding present and future thin-seam operations.

Jan 1, 1987

By W.A. van der Westhuizen

Mineral resource management has become a well used phrase in the mining and minerals industry. Mineral resource managers are being appointed in many mining and mining-related organisations. Every mineral resource manager has his/her own ideas regarding what MRM means. There seems to be a tendency to define MRM close to home; geology would apply MRM principles to their environment and so will metallurgy, planning, mining, survey and every discipline and participant in the mining value chain. What do we do in the MRM environment and what do we aim to achieve? Surely we must have goals: what are they? Is value tracking MRM? What about best practices? Let us start at the beginning: what do we want to achieve in any mining operation? The minerals industry would like to make money, now and in the future. This calls for serious management inputs. The most important aspect is a holistic management approach regarding the total mining value chain. Process optimisation follows with application of Mineral Resource Throughput Management (MRTM) and Process Flow Management principles. Once flow processes have been established the necessary condition driven standards and measurements will be installed to ensure continuity in applicable processes.

Jan 1, 2012

By L. C. Raymond

Good afternoon. I have entitled my talk "Investment for Progress," implying thereby a spark of friendly competition by private enterprise with such government-inspired foreign aid and investment programs as the Alliance for Progress. While the subject of foreign investment is hardly a new one, the perpetual flux of the political and economic surface of this earth we inhabit makes it forever timely and forever interesting. Especially do tremendous opportunities for international investment constantly present themselves to the mineral industry, and just as often must the industry approach these opportunities with a great deal of investigation and caution. This is not to say that the mineral industry--no less than any other industry--should be unenthusiastic about the foreign scene, but like everyone who proposes to put his money where his hope is, it should consider all the factors and weigh the possible disappointments as well as the rewards.

Jan 1, 1964

By R. A. Hill

A brief explanation of the theoretical functioning of a regenerative system followed by its application to firstly, shuttlecars and then continuous miners and its effect on performance thereof with regard to handling, production and safety.

Jan 1, 1986