Search Documents

A Mark IV surface force apparatus (SF A) was used to conduct direct force measurements in dodecylamine hydrogenchloride collector solution between mica surfaces at varying pHs. It has been found that the long-range hydrophobic forces reach a maximum at pH 9.5, which also corresponds to the maxima attained by the contact angle and flotation recovery of quartz. The charge densities are comparable on both mica and quartz surfaces (0.40-0.48 run2), making it possible to draw conclusions on the flotation of quartz from the direct force measurements conducted on mica. Therefore, it may be suggested that the maximum flotation recovery of quartz m the range of pH 8.0-10.3 may be attributed to the appearance of long-range hydrophobic force, which in turn can be related to the formation of a close-packed monolayer (or hemimicelle) in the presence of neutral amines formed as a result of hydrolysis.

Jan 1, 1996

By Wayne Stange

Due to the availability of user-friendly microcomputer based packages, the use of simulation is increasing.. Users have however encountered problems inherent to the structure of sequential-modular simulators. These are the difficulties associated with estimating parameters for arbitrary' models and the solution of design and optimization problems. The implementation of an optimization routine in the simulator MicroSim has facilitated the solution of such problems. The literature indicates that more efficient numerical techniques for solving optimization problems than those presently used in MicroSim are available. These techniques, together with user-interfaces which allow such problems to be specified easily by users, will result in the development of simulators much more powerful than existing ones.

Jan 1, 1989

By C. J. Gauvin

The Geological Department, headed by the Chief Geologist, is part of the General Engineering Division and is under the direct supervision of the Chief Engineer. The Geological Department is responsible for the technical direction of all work concerned with the finding and outlining of ore. It provides the mine operating staffs, with the necessary plans and sections to enable them to design pit and underground layouts and to, extract ores' as required by outgoing cargoes. The department maintains grade and ore reserve statistics in conjunction with a mining recovery factor at year-end. These duties are performed through the co-operation of all departments participating in the overall operation. As a result, a steadily broadening use is being made of geology at Steep Rock.

Jan 1, 1960

By C. Ottergren

A process does not have higher capacity than what can pass through its bottleneck. Acknowledging this, and with the goal to optimize production at a minimum investment, one can use existing equipment, modify the process flow and make a few strategic capital investments. Automatic setting regulation is a technology that allows balanced crusher performance matching minute changes in feed material characteristics. The system makes it possible to utilize the crushers fully at all times. It also continuously and completely compensates for manganese liner wear.

Jan 1, 1999

By Joel Lööw, Jan Johansson, Lena Abrahamsson

In this study, we try to illustrate what new technology can mean for the individual miner. We formulate the notion of Mining 4.0, where we attempt to create an image of how the future might look from a miner’s perspective and how mining companies might navigate their way to a future that works for all miners. 

By Collin L. Stewart

Published subsidence data for the western United States is limited in comparison with data for the east. This paper summarizes the results of a subsidence monitoring program above two longwall panels at the Foidel Creek Mine located in northwest Colorado. The monitoring area is characterized by overburden ranging from 1000 ft to 1100 ft in thickness. The surface slope parallels the dip of the bedding at approximately 5 deg. Average mining height is 9 ft. Smax averaged 3.4 ft. Draw angles averaged 15 deg for up-dip ribsides and 19 deg for down-dip ribsides. A site-specific profile function is developed from the data.

Jan 1, 1986

By Val E. Payne

Issues between resource utilization and resource preservation often develop in connection with coal mining. One such conflict exists in eastern Utah where PacifiCorp and Energy West Mining Company are working with State and Federal agencies to address the resource recovery/resource preservation dispute. The effects of underground longwall coal mining on golden eagle (Aquila chrysaetos) cliff nesting sites have been studied at the Cottonwood Mine since 1986. Subsidence, escarpment spalling, and the nesting activities of the local eagle population were monitored.

Jan 1, 1986

By M. J. Shulman

The exploration geologist is frequently confronted with the problem of allocating his resources, i.e., exploration effort, among various areas. Although geologic, financial, and logistic considerations influence the allocations, no objective criterion is usually given that determines the optimal allocation. Maximizing the expected gain in information, subject to the constraint of a limited exploration budget, is used as the objective criterion to allocate airborne reconnaissance effort. The information function, I(x), quantifies the expected gain in information, where x is the scale of exploration. To calculate the information function, the following probabilities are required: the probability that an area contains a deposit; the probability that an anomaly is produced by the target; and the probability that an anomaly is produced by a barren area (false signal). Alternatively, the barren areas can be replaced by other targets. To illustrate the allocation method, the optimal number of line kilometers, i.e., the optimal line spacing per area, is determined for an aeromagnetic survey for iron in Egypt.

Jan 1, 1987

"The National Mining Hall of Fame and Museum (NMHFM) announced the class of 2019 National Mining Hall of Fame inductees. This year’s inductees, selected by the National Mining Hall of Fame’s Board of Governors, represent exceptional financial acumen in assembling several operations that formed the basis of a successful American mining company; conception and development of equipment which contributed to improved efficiency and mine safety; and unrelenting advocacy for the U.S. mining industry and its workers. These individuals, selected for being determined, forward-thinking innovators, doers and leaders have propelled the industry toward vastly improved safety and social responsibility.The Prazen Living Legend of Mining Award, named for renowned mining artist Gary Prazen, will also be presented at the ceremony. This award recognizes an individual or organization for significant and sustained commitment to educating the public about the relationship of mining to our everyday lives through educational materials, programming, and outreach.2019 National Mining Hall of Fame inducteesFrank Calandra, Jr. has devoted more than 50 years to the mining industry and he is an icon in ground control technology for the mining, tunneling and civil construction industries.From the ground up, his passion, sweat equity and shrewd business acumen have grown Frank Calandra, Inc. (FCI) and Jennmar from a single plant in Pennsylvania to a world-class enterprise with 25 plants employing thousands globally. As evidenced by Calandra’s more than 20 patents on ground control devices (not to mention the additional 80 patents his companies hold), his innovation and commitment to safety have made underground mining safer and more efficient. In the late 1970s and early 1980s, Calandra was instrumental in upgrading American Society for Testing and Materials (ASTM) standards in roof control for both state and federal regulations. Through his work with industry associations such as the National Mining Association, National Coal Council and Center for Energy and Economic Development, among others, Calandra has contributed his time, expertise and financial support to ensure a balanced political and regulatory climate for mining. Calandra is an inductee of the West Virginia Coal Hall of Fame."

Aug 1, 2019

By A. Habibi

A study has been undertaken on two 1.12 m diameter industrial booster fans operating under different blade settings powered by a 1200 rpm motor at the Missouri University of Science and Technology. The fans total pressure varies up to 1kPa forcingup to 25 m3/s through the workings. A pressure-quantity survey has been conducted inby and outby the booster fans with different blade settings. The study uses a variable speed drive (VFD) to determine the effect of rotational frequency on the system. The pressure drop across the bulkheads has been monitored during the experiments. The fans were operated with various blade settings to determine the optimal scenario that maintains the maximum airflow quantity and the lowest power demand at a particular ventilation station. Five scenarios were conducted with different blade setting and mostly with two different speeds. The experimental results show that alteration of fans? speeds by use of a VFD unit can reduce power consumption while maintaining airflow requirements. With the flow rate forced through the mine by the surface fan the blade settings 4 and 5 were determined as possible alternative for the mine ventilation system. In scenario 4, the airflow at the particular ventilation station for a number of speeds is over 20m3/s. The power consumption at 1080 rpm was measured to be 20.1 kW compared to 25.5 kW at 1200 rpm. The operating cost would be significantly less at lower speeds. Scenario 5 is the alternative making use of both booster fans and the main fan in series that meets the minimum airflow requirement at the particular ventilation station along with minimum power consumption. Reducing both booster fans speeds to 1054 rpm results in power consumption of both together dropping to 11.8 kW. Therefore blade setting 5 using two booster fans was determined to be the optimal setting. Separately it was determined that the combination with use of only one booster fan, the West booster fan, running in series with the main fan is the overall optimal scenario. The power consumption of the West booster fan was calculated to be 8.8 kW at 860 rpm with the minimum airflow requirement being met. Computational fluid dynamics is used for analyzing three dimensional flow structures in time domain and calculating the corresponding unsteady pressure fluctuations. The sliding and dynamic mesh techniques were used to study the unsteady flow interaction arising due to the rotation of the fan blades. The numerical predictions of the variables in the form of velocity vectors and contour plots detailing the flow characteristics are then analyzed according to the known physical situation and existing experimental data.

Feb 27, 2013

By L. Wilfley, G. A. Calboreanu

"Wear resistant 25% Cr hard cast iron is a heterogeneous material containing 1,600 HV hard chromium carbides embedded into martensitic matrix. It is the most used cast alloy in wear operations of mining industry, chemical industry, fracking, etc. During the last decade the hard iron manufacturers increased wear resistance in the following ways: • Reduce / eliminate harmful retained austenite and chromium + carbon depleted areas especially within eutectic carbide cells. In Max5A the improved 25% Cr alloy brittle carbide eutectic cells are removed which increases toughness. • Delay delamination between chromium carbides and matrix particularly during sliding abrasion wear. Delamination commences at the weakest chromium carbide – matrix contact lines exposing chromium carbide to localized bending stresses which gradually chip carbides away. Once the chromium carbide base is removed accelerated wear degradation occurs. • Evenly randomize and avoid discontinuities in the chromium carbide network. When chromium carbides are perpendicularly positioned to the wear surface wear rate is minimized. On the contrary the highest wear rate takes place when 3D oriented chromium carbides are parallel with the wear surface. In this case chromium carbides cover top network discontinuities being just matrix supported which leads to rapid carbide cracking. The new hard iron discussed in this paper fulfils and exceeds the above requirements increasing the casting service life around 250% in various wear operations. Physical and mechanical properties of Max5A are compared with well manufactured Industry Standard 25% Cr hard iron. The paper presents practical accomplishments obtained in the USA, South America and India. INTRODUCTION The chemical composition of Max5A and Industry Standard 25% Cr are identical like specified by ASTM A532 Class III Type A requesting C = 2.0-3.3% and Cr = 23.0-30.0%. Manganese, silicon, nickel, molybdenum and copper contents are limited by maximum accepted quantities.[1] According to published data the eutectic chromium carbides chemical composition of 25% Cr hard iron is Cr = 54% and C = 8% which indicates strong depletion of chromium and carbon along chromium carbide - matrix interfaces. [2] The optimized Max5A microstructure has minimized retained austenite, is devoid of harmful carbide eutectic cells and has the most advantageous chromium carbide and secondary chromium carbide morphology. This favorable microstructure increases wear resistance, mechanical properties and corrosion resistance. The paper compares the Max5A microscopic features and mechanical – physical properties with similar properties of high quality Industry Standard 25% Cr."

Jan 1, 2017

By K. M. Kolin

ABSTRACT OF ORAL PRESENTATION A discussion of current U. S. Bureau of Mines research into the problem of strata control in multiple Western coal seams will be presented. The problem and research priorities will be described as determined from interviews with major Colorado and Utah mine operators as well as governmental agencies responsible for Federal leases. Proposed contract research and ongoing in-house studies will be discussed, including case histories and results from projects being conducted at two multiple seam operations in Utah.

Jan 1, 1977

By G. W. Heunisch

The properties of Neutra-Fix® and Neutra-Ment®, two new lime substitutes for treating acid mine drainage (AMD), have been compared with lime and Allcament®, two products presently in use for AMD treatment. The two new products are basically dolomitic byproducts and produce sludges that are more compact than those from lime. Sludge settling rates are faster than lime with iron concentrations after 24 hours that comply with Environmental Protection Agency (EPA) regulations. Material utilization and optimum pH are reported.

Jan 1, 1988

By Isabel F. Barton, MarkD. Barton, Christian A. Rathkopf

Molybdenite is the world’s principal source of rhenium (Re), a critical element in multiple high-tech applications. However, the Re contents in molybdenite vary by orders of magnitude on scales ranging from single grains to whole deposits. In order to better understand the systematics of this variation and what geochemical factors control molybdenite Re concentration, and hence overall Re resources, we examine global patterns in molybdenite Re contents through a compilation of > 3000 measurements of Re in molybdenite from > 700 mainly ore-bearing moderate- to high-temperature hydrothermal systems of different types. Our results are similar to but expand on those of earlier studies. Rhenium concentration in molybdenite has a lognormal distribution and varies systematically with type of geologic system, intrusive lithology, and Mo grade. The lowest-Re molybdenite occurs in greisens (geometric mean 1 ppm ± a multiplicative standard deviation of 9), quartz vein-hosted W-Sn deposits (2 ± 5 ppm), unmineralized granites and granodiorites (12 ± 8 ppm), intrusion-related deposits (24 ± 8 ppm), and porphyry W-Sn deposits (16 ± 11 ppm). Rhenium is most enriched in molybdenites from volcanic sublimates (23,800 ± 5 ppm), with skarn Fe and Au (560 ± 5 ppm and 540 ± 3 ppm respectively) and porphyry Cu and Cu-Au deposits next (470 ± 4 and 430 ± 7 ppm respectively). Among porphyries, skarns, and quartz vein-hosted deposits, Re is most highly concentrated in molybdenites from Cu and Au systems and its concentration decreases systematically through Cu-Mo, Mo, Sn, and W deposits. In nearly all cases, molybdenites from systems associated with intermediate igneous rocks contain more Re than molybdenites from systems of the same type with more felsic rock associations. The disparity between Re contents of molybdenite in felsic and intermediate systems is largest for porphyries, quartz vein-hosted, and skarn deposits and is near zero for subeconomic or barren granite and granodiorite Mo systems; felsic intrusion-related deposits have slightly higher molybdenite Re than their equivalents associated with intermediate intrusions. In most systems, molybdenite Re content does not correlate with metal grade, but may have an inverse correlation with Au grade in intrusion-related deposits (based on a small number of data points) and does exhibit a strong inverse correlation with deposit Mo grade. Dilution of Re through larger amounts (higher deposit grades) of molybdenite explains about 40% of this correlation, but the relative enrichment of Re in molybdenite from low-Mo deposits must also reflect some selective enrichment of Re/Mo in porphyry Cu systems compared to porphyry Mo systems. We found no evidence for secular increase or other systematic temporal variation in molybdenite Re content. The data regarding the use of molybdenite Re content as a proxy for mantle influence are ambiguous. Nearly all observed empirical correlations can be traced back to differences in redox state and sulfide concentration, the two geochemical factors identified here and by previous experimental work as the controlling influences on Re mobility under hydrothermal conditions. Hydrothermal systems with reducing conditions (W- and Sn-rich) tend to have low molybdenite Re even though compiled whole-rock data indicate that their source rocks have as much or more Re as those of more oxidized systems (e.g., Cu-rich). Vapor-phase exsolution, crustal assimilation, and mixing with external fluids may all enrich molybdenite Re concentrations in individual deposits and deposit types, but their extent and importance in overall hydrothermal concentration of Re is uncertain. Thus, it appears that the available molybdenite Re resource in an ore deposit largely depends on how the deposit’s redox and sulfidation conditions have varied over time and space during the timespan of hydrothermal activity. Oxidized, high-sulfide conditions tend to concentrate Re in molybdenite, whereas reducing conditions tend to leave Re dispersed at low concentrations in the bulk rock.

By P. Rosario

During the last few years high-tonnage plants have been designed with comminution circuits using semiautogenous grinding (SAG) mills, high pressure grinding rolls (HPGR), or both, followed by ball mills in different configurations. A strong interest in improved energy efficiency and reduction of carbon footprint, along with the recent launch of new high-capacity crushers and stirred grinding mills, has driven the industry to investigate the development of novel flowsheets. This paper presents work based on recent projects that include modeling and simulation of two innovative circuits recently considered for current projects. One circuit uses autogenous (AG) mills and parallel trains of crusher-HPGR and the other is a modified three-stage crushing circuit with the use of HPGRs and pebble mills. The paper indicates the potential savings in operating costs provided by the HPGR-pebble mill circuit when compared to a more conventional SAG-mill-based circuit.

Jan 1, 2010

By Richard H. Johnson

White Pine Copper Company, a subsidiary of Copper Range Company located in Michigan's Upper Peninsula, mines a Precambrian sedimentary deposit containing finely disseminated chalcocite, native cop- per and native silver. Silver occurs predominately in certain strata and presently provides a mill head averaging 0.25 ounces per ton. This technical publication traces the development of silver recovery at White Fine beginning in early 1961. White Pine refined copper contains an excess of silver over and above that required to impart Lake Copper properties. The copper does not require electrolytic refining to meet industry purity requirements, nor is there sufficient silver to justify electrolysis.

Jan 1, 1970

By PETER ROBINSON, KEVIN BARBER, OLIVER WHATNALL

The investigation and uptake of filtered tailings continues to grow around the world, but cost and scalability are deterrents for mining companies. Filtration technology that is currently in use is unable to meet the needs of many operations and projects that would otherwise adopt filtered tailings. For tailings to reach the desired moisture content for dry stacking, the majority of processes require pressure filtration, with significant upfront and ongoing maintenance costs. Given the comparative lower costs associated with low-pressure Viper vacuum belt filtration, this technology has the potential to alleviate dependency on high-pressure applications and make efficient dewatering and handling of tailings a more economic and sustainable solution.

By Kamran Esmaeili, MINGLIANG TANG

An understanding of the spatial and temporal variations of surface moisture content over a heap leach pad is essential for leaching production and to achieve a high ore recovery. The current leach-pad monitoring and data-collection practice remains highly labor intensive and exposes technical staff to cyanide solution, a hazardous material. To address these challenges, we propose using unmanned aerial vehicles (UAVs) equipped with thermal imaging sensors to remotely obtain image data with high temporal and spatial resolution for monitoring the surface moisture distribution over heap leach pads. A field study was conducted over a sprinkler-irrigated heap leach pad at El Gallo gold mine in Sinaloa, Mexico, and the acquired data were used to generate moisture distribution maps of the heap leach pad’s surface. The created moisture maps provide direct visualizations of surface moisture variation over the surveyed area. Such graphical results are effective tools for inspecting heap-leaching operations.

By Kirk Carlton

The Athabasca tar sands of Alberta are an increasingly important source of crude oil for the North American continent. Published figures indicate estimates of recoverable resources in the tar sands at some 300 billion barrels of synthetic crude of which some 86 billion barrels can be recovered by surface mining techniques. At the present time, two commercial plants are in operation, Great Canadian Oil Sands Limited and Syncrude Canada Ltd. Their present combined capacity is approximately 150,000 barrels per day. Some of the factors which will make this oil expensive will be noted here. The location of the present producing plants is 500 kilometres north of Edmonton at an elevation of approximately 320 metres. Recorded temperatures range from +38 to -55 degrees Celsius. Wind velocities are not high but the chill factor with even a slight breeze and minus 40 degrees is very uncomfortable.

Jan 1, 1979

Automated drilling in surface mines is here, it?s successful, and it?s already at work in mines around the globe. Coal, copper, iron and gold mines in large mining countries such as Canada, Australia, South Africa, the United States and Chile are meeting mining objectives previously ruled out as unattainable. Pit Viper automation enables operators to accomplish more objectives safely. Operator assist functions like AutoLevel, AutoDrill, Auto Rod Changer and multi-rig teleremote control are a few of the features mines are using to gain consistent, sustainable productivity.