Search Documents

By Hans Hamrin, Bruce Kennedy

Once an ore body has been probed and outlined, and sufficient information has been collected to warrant further analysis, the important process of selecting the most appropriate method or methods for mining can begin. At this stage, the selection is preliminary only, serving as the basis for a project layout and feasibility study. Later, it may be found necessary to revise the details, but the basic principles for the ore extraction should remain a part of the final layout. With respect to the basic principles employed, relatively few mining methods are used today. For the purposes of this presentation, the principles are classified as follows: 1) For naturally supported stopes, the available methods are room-and-pillar mining and sublevel stoping. 2) For artificially supported stopes, the available methods are shrinkage stoping, cut-and-fill mining, square-set mining, and longwall mining. 3) For caving methods, the available techniques are sublevel caving and block caving. Due to the uniqueness of each ore deposit, the variations on each of these methods are nearly limitless. It is impossible to include even the major variations in this chapter; the goal of this chapter is to present the principles as a guide to the mining engineer in adapting the general methods to specific needs. The selection process described herein is intended to supply the techniques by which the candidate methods available for a given ore body can be reduced to one or two feasible approaches. The feasible approaches then can be evaluated in detail, and the particular modifications can be investigated. In describing costs and economic factors, all values herein are expressed in terms of 1978 US dollars.

Jan 1, 1982

Collaboration between education providers is the key to long-term sustainability and improved quality in mining education. The mining industry is now, more than ever, an industry doing business on a global basis. Staff are recruited by global mining companies in many different countries and can find themselves deployed anywhere in the world. The mining engineer of tomorrow must be willing to take on this international challenge, and must be educated to a level where he or she has a comprehensive grounding in technical aspects of mining engineering, but also a well-founded appreciation of management, social, environmental and cultural issues that may be encountered around the world. In order to deliver such an education, academic providers must collaborate at both a national and international level. This paper provides an overview of progress that has been made in Australia through the national joint venture ? Min¬ing Education Australia (MEA). Supported by the mining industry in Australia, through the Minerals Council of Australia (MCA), MEA has been operational since 2007 and is seeing the development of a range of innovative courses and delivery methods, together with a high level of staff cooperation across the country. MEA has also commenced some international teaching initiatives that are seen as a catalyst for a far greater degree of international collaboration in the future. Such activity is not only to the benefit of the students who are taught by experts from around the world, but it also ensures that individual univer¬sity programs remain viable in terms of staffing numbers and financial performance. The paper also presents some statistics on recent upward trends in mining engineering student numbers from around the world, in response to the global shortage of mining engineers.

Jan 2, 2010

By Oscar Letelier Gonzalez

The goal of mine planning is to determine "the best" strategy to exploit an ore deposit during its workable life. Such strategy must be consistent with the objectives of the company and must be subject to the contraints imposed by economical, physical and geological conditions. Mine planning process may be broken down into three categories, according to the planning horizon: Long range, Short range and Operational. The shorter the scope of planning, the higher the level of details and the lower the degree of freedom associated to each plan. A long range plan defines the economic limit of mining at the mining life end of the deposit; it also can be used as an aid in the evaluation of the economical potential of a mineral deposit and as a guide for short range plans.

Jan 1, 1979

By Jin Anshi, Wang Dai, Wang Zingshen

Both fire and gas problems in Fully Mechanized Sublevel Caving Coat Face are quite different from those in common fully mechanized coal face. Pouring N2into the goaf would be the best method to prevent fire in the goaf. In this paper how to determine parameters of pouring N2 is discussed. Comparing distributions of gases and temperature before pouring N2into the goaf with those after pouring N2 into the goaf, the effectivenesses of preventing the fire by pouring N2 into the goaf are testified. Some special gas problems appear in Fully Mechanized Sublevel Caving Coal Face, which are proved to be serious and interrelated with pouring N2 into goaf. Finally, a few methods adopted to deal with gas problems are described simply.

Jan 1, 1991

By Jacques Deraisme

Geostatistics has been applied in many mining feasibility studies throughout the world during the last decade. Recently geostatistics has begun to be applied to the field of mining processes by attempting to aid in the definition of the best mining policy. For a feasibility study the grade-tonnage relationships give a reasonable order of magnitude estimate of the ore reserves within the deposit. But the reserves that will actually be recovered, will vary depending upon the mining methods and the technical means used. The profit earning capacity of the mining project is determined by a great many factors, such as for instance: accessibility of reserves to extracting machines, the haulage distance between the mine and the mill, the variability of produced ore (tonnage and grades) which could necessitate stockpiles or blending areas?

Jan 1, 1979

By M. A. S. Martins, H. Medeiros, B. Y. B. Dos Santos

This paper contains the geometallurgical studies, performed for Mineração Rio do Norte bauxites, applied to a selected area belonging to Plateau Saracá III, referring to an exploitation period of one year and three months, approximately. It is worth mentioning that Mineração Rio do Norte has the biggest bauxite operation in Brazil producing 8,500,000 tons of concentrate per year. The studies included wide investigations directed to the final objective of establishing a precise mining and production planning, based on the different behavior of the distinct bauxite ores, when submitted to industrial processes. Geometallurgy can be defined as the study of the regionalization (space distribution) of the metallurgical variables of a mineral deposit. This study involves and integrates all process engineering, geology, geostatistics and mining planning, among others. The development and application of the geometallugical studies to Mineração Rio do Norte were motivated by several reasons and necessities, among them: 1. Improving the forecast of the amount of concentrate (metallurgical mass yield) produced; 2. Improving the equipment operational efficiency, providing a more homogeneous feed; 3. Conducting a more precise material balance that permits a better daily, monthly and yearly production control; 4. Improving the forecasts for the final products generated by each ore type; 5. Obtaining better knowledge of the behavior of several ore types, submitted to the different process unit operations; 6. Promoting adequate ore blending, producing an homogeneous feed during mining operation.

Jan 1, 1998

By Randal J. Barnes, Franck Rellier

Mine ventilation survey data includes generally redundant, usually inconsistent, often incomplete, and always noisy measurements. Yet, these data are essential for operational decisions and represent the foundation of any mine ventilation systems model used for future engineering analysis and design. For example, the basic ventilation network geometry can be measured with a reasonable precision, the network flows can be measured, but with significant errors, and the branch resistance factors can not be directly measured at all. The network-based, constrained weighted least squares approach, presented in this paper, advances a method for the sys tem-wide adjustment of ventilation branch measurements and the consistent estimation of global system parameters (e.g. branch flows, head losses, and resistance factors). The constraints guarantee that the adjusted values satisfy the governing physical laws: conservation of flow, conservation of energy, and the appropriate energy dissipation rule (e. g. Atkinson's RQ2). The weights allow for the proper inclusion of data with widely disparate precision, as well as offering a simple method for retiring old data as the mine changes through time. The post-adjustment sensitivity analysis presents two potentially useful forms of analysis: the identification of previously unspecified leakage branches, and the semi- automatic recommendation for future ventilation measurement campaigns. The overall efficiency of the algorithm is exemplified by the fact that a ventilation network with hundreds of branches and thousands of measurements can be routinely adjusted on a microcomputer.

Jan 1, 1989

By H. Gurgenli

Mining companies require accurate short-term mining forecasts to meet budget targets and customer needs. Challenging mining conditions along with employee turnover and lack of standard geologic modeling and mine planning processes can result in time-consuming and inconsistent mine plans. Documentation and automation of the processes involved in mine planning, as well as proper software utilization, are critical in overcoming these challenges. This paper discusses the steps involved in achieving an optimized mine planning system to accomplish productive and cost effective operations. In addition, a case study is included to describe the process of implementing a semi-automated system whereby the geologic model and mine scheduling database are updated monthly to incorporate changes in geology in a relatively complex open-pit coal mine. This case study proves that the ability to update geologic models based on the latest information gathered from production drilling and mining activities can greatly enhance the ability to accurately predict short-term mining production.

Jan 1, 2011

By C. O. Lee

The Grand Isle Sulphur Mine is located in the Gulf of Mexico, approximately seven miles off the coast of Grand Isle, Jefferson Parish, Louisiana. The depth of water at this location is about 50 feet. The deposit is on acreage covered by oil, gas, and mineral leases which were originally issued in favor of Humble Oil & Refining Company by the State of Louisiana, and which were continued, maintained, and redesignated by the Department of the Interior of the United States, pursuant to Section 6(b) of the Outer Continental Shelf Lands Act. On September 19, 1956, Freeport Sulphur Company acquired from Humble Oil & Refining Company the sulphur rights underlying the tracts. This assignment was approved by the Secretary of the Interior on July 12, 1957. The Director, United States Geological Survey, approved Freeport Sulphur Company as Operator on July 31, 1957. Actual design began in September 1956; the first structural contract was let December 15, 1957, and offshore erection began in June 1958. The initial phase of construction will be completed and production started in early 1960. The estimated total cost of the project is $30,- 000,000, of which $8,000,000 is the extra cost for being in the Gulf of Mexico.

Jan 1, 1959

By P. C. Thakur

The productivity in coal mines, measured in terns of the output per manshift depends largely on the efficiency and speed of men and materials transport between working faces and the surface. The mechanization of coal winning and material handling processes has led to a great rise in the mine productivity (1). Early applications of power in U. S. coal mines were mainly electrical. The excellent traction available with the DC motor and the ease of the distribution of the DC power have made trolley wire installations for haulage very popular. In shallow mines with very limited emissions of methane it did not constitute a major hazard but as mine depths increased and corresponding emissions of methane also increased fire and methane ignition hazards have become very serious. Conveyors have proved economic where intense mechanization of coal faces generates a large output of coal from a single face, but the fire and respirable dust hazard associated with them are no less serious. Recognizing these shortcomings, the Federal Coal Mine Health and Safety Act of 1969 laid down numerous provisions for the safe use of trolley-wire haulage and conveyors (2) which generally improve safety but in some cases complicate mining operations and have decreased productivity significantly since 1969. In course of time as coal mines become deeper and hence gassier and as the emphasis on safety increases it would be inconceivable to use trolley-wire haulage under ground as already witnessed in several other countries with deep coal mines. With rising capital investments and cost of the protection against fire and respirable dust, the use of conveyors may also have to be limited to special areas, e.g. main entries. Indeed, there are only two alternatives available, namely; (1) Degasify the coal seams prior to mining and use conventional electrical power, or (2) Develop alternate sources of power which would be safer and yet efficient and cheap.

Jan 1, 1975

By D. K. Sengupta, T. K. Rout, A. R. Prasad, B. P. Singh

The filter cake from the vacuum drum filters of a uranium ore processing plant still contains some leach solution. If the filter cake is not efficiently washed the associated leach solution is lost. Therefore, it is necessary to produce a filter cake that is permeable enough to allow efficient washing. The dewatering characteristics of the solid-liquid system must be improved to obtain flocs with sufficient strength to withstand the suction pressure of the filtration system. To facilitate efficient filtration with minimum cake moisture, studies were undertaken to improve the dewatering characteristics of the cake using different types of flocculants and surfactants. In these studies, flocs were formed with anionic, cationic or nonionic flocculants. The best performance was obtained with a low cationic high molecular weight flocculant. The filtration parameters, namely, capillary suction time, cake resistance, cake permeability and final moisture content of the filter cake, are improved by using a combination of flocculant and nonionic surfactant.

Jan 1, 2002

By Kerry Burns

Contrary to active subsidence, which occurs concurrently with mining operations, or is completed within a few days following coal extraction, delayed subsidence may take many years to appear at the surface after coal mines are abandoned. There are two principal morphological types of delayed subsidence: troughs, which are shallow depressions, and sinks, which are steep-sided crown pits. Both types are damaging to surface structures, and a variety of methods have been introduced to deal with the problem, ranging from subsidence insurance to site restitution. In planning insurance or restitution measures, a predictive model is of value in estimating the magnitude of the problem and the size of long-term budgetary commitments. Only one model is known, which was developed for the Bureau of Mines by GAI Consultants of Monroeville (l,2,3). The GAI model is presented in qualitative terms. This report develops a formal basis for the model and tests a numerical implementation on one of the best-described study areas, Allleqheny County in Pennsylvania.

Jan 1, 1982

By William Connell

NFPA 502, Standard for Road Tunnels, Bridges and Other Limited Access Highways establishes minimum fire protection and fire life safety requirements for road tunnels, bridges and other roadways where access by emergency responders is physically limited. The 2008 edition of NFPA 502 represents the Technical Committee?s consensus of current best practice for fire protection and life safety requirements for road tunnels, bridges and similarly limited access highways. Research of national and international test programs, design guidelines and regulating standards was per-formed and considered in an effort to establish a singular, comprehensive document representing a recognized base threshold of fire safety in these type facilities. This paper provides an overview of the more significant revisions including the application of fixed fire suppression systems, guidance on tenable environment, protection of structure and dangerous goods transport.

Jan 1, 2008

By D. Bessinger, J. Nell

The electrical conductivity of rutile was optimised as a function of time, temperature and gas composition. These optimised conditions were used to treat rutile/zircon feed prep concentrate samples from a South African heavy minerals producer, prior to electrostatic separation. Enhanced separation between rutile and zircon was obtained when compared to untreated samples. Samples treated in a hydrogen atmosphere and cooled in nitrogen showed the best separation when passed through a high tension electrostatic separator using conditions of high sample temperature and high relative humidity.

Jan 1, 2005

By William Gleason

During the past five years, mining operations have had access to press technology for piping and joint fittings that can save owners a significant amount of time when installing or replacing pipes by eliminating the need for welding or threading. Viega, with North American headquarters in Wichita, KA, entered the mining sector in 2009, adding to its already expanding industrial sector. Since then, the company?s global engineering department has paid considerable attention to its industrial division, bringing its expertise in plumbing solutions for residential and commercial buildings to the mining and mineral extraction industry. ?We have a lot of applications in the mining industry.?We have a lot of applications in the mining industry throughout the United States, Canada and Mexico and continue to expand in the mining industry,? Tom Shields, Viega?s director for industrial accounts explained. ?Since we made the decision to increase our presence in the industrial markets, we have been aggressive and more than 240 applications have been approved by our engineering department in Germany.? Getting approval from Viega?s engineering department is no small feat. During a tour of the manufacturing facilities in Ennest and Großheringen, Germany, Mining Engineering, as well as a select few other publications and clients, were shown Viega?s manufacturing process. At the Ennest facility, hundreds of millions of fittings are produced, and each one is inspected mechanically and with a laser at the end of the production line. With four production facilities in Germany and one in the United States, Viega is able to ship to anywhere in the world. The company distributes everything from fittings to stainless steel pipe.

By Paul Dean Proctor

The world's population by 2000 A. D. may approximate 6.5 billion and the United States' 304 million. South Asian population increases between 1970 and 2000 A. D. will be triple the projected population of North America. Such anticipated dramatic and probably traumatic increases in world population yield grave concern for the standard of living in the world and the United States. The people of the United States currently consume 32 percent of the world's energy and similarly large percentages of the world's mineral raw materials. With only 6 percent of the present world's population and slightly smaller percentage by 2000 A. D., much expanded world-wide production of energy and raw materials will be required to maintain even a standstill living standard. A minimal 2 percent increase per year in the standard of living in the United States and a 4 percent increase elsewhere in the world, beyond the demands of the estimated population increases, suggest the magnitude of the increased need for energy-mineral raw materials and the possible crises the world will face in these areas by 2000 A. D. Mineral engineers and scientists with broad educational backgrounds will be required in greatly increased numbers to help alleviate, and possibly avert, expected energy-mineral raw materials shortages of the next millenium. Explorationists, mineral engineers, commodity economists, environmentalists, city, county, state, and federal mineral materials planners and coordinators, and metallurgists will be among those most needed. AIME membership in the second century of the Institute's history will contribute directly to this personnel pool.

Jan 1, 1971

By A. I. Kalugin, A. A. Abramov, D. E. Kozlov

As a result of thermodynamic analysis of a mineral-sodium, oleate-water system, flotation and adsorption tests at various pH values, and sodium oleate concentrations, it has been established that due to regularities of phosphate-containing minerals (fluorapatite, hydroxyapatite, carbonatapatite) flotation cannot be explained by the formation of alkali-earth metal oleates on their surface. This paper presents a novel theory that connects optimal conditions for mineral flotation with zero charge of its surface, which can explain the regularity of minerals flotation observed. The quantitative physicochemical flotation models developed based on the theory are suitable for improving industrial processes, conditioning of recycling waters, and application in automatic control systems at the plants. Key words: apatite, oleate, flotation, modeling, control, and regulation.

Jan 1, 1999

By Kai Koosmen, Mehdi Serati, Tengzhou Wang

Spalling and rockburst are unwanted brittle failures at the boundaries of underground excavations that are commonly observed in hard rock and high-stress environments at significant depths, although, spalling has also been observed in comparatively shallow soft rocks. The crack initiation (CI) stress threshold (representing the stress level at which new micro cracks begin to form in an intact rock) is widely used to establish the in-situ spalling strength, and is generally regarded as the lower limit of the long-term rock strength. This study analyses the evolution of CI and other mechanical properties for a high-porosity sandstone with an average UCS of 38 MPa under unconfined cyclic compressive loading. The results indicate that rock properties are variably affected by cyclic loading with; no significant effect on Youngs Modulus; a moderate increase in Poisson’s ratio and fracture angle; a moderate decrease in UCS; and a major reduction in the CI stress threshold. All of these changes were generally amplified by cyclic loading at higher stresses. From the results, it is concluded that rockburst and spalling limit in underground structures may reduce over time if the rock is subject to repetitive cyclic loading, and that the reductions will be greater for higher cyclic stresses. This may be a significant factor in the design and operation of some deep underground structures.

Apr 26, 2022

By Gale F. Hoffnagle

INTRODUCTION On November 15, 1990, President Bush signed the Clean Air Act Amendments of 1990. These Amendments cover many aspects of air pollution control. The provisions which seek to control emissions of "air toxics" may, however, be the most far-reaching and will potentially have the greatest effect on American industry. The Administration has estimated that by the year 2005 industry will be spending $6.7 billion per year on air toxics control. Meanwhile, the Business Round Table has estimated that the price will be far higher, up to $62 billion per year, depending on how EPA and the States implement the program. BASIC REQUIREMENTS Any "major" source of emissions of 189 air toxics will be required to install "MACT." The translation of this statement requires some definitions: •MAJOR SOURCE - A facility (a contiguous property under single ownership and control) which has actual emissions of 10 tons or more per year of any single one of the air toxics or 25 tons per year of any combination of air toxics. •AIR TOXICS - Congress has provided a list of the 189 chemicals on this list. Those that may be important to the mining industry are shown on Table 1. This list can be changed by petition or by EPA. •MACT - Maximum Achievable Control Technology is to be defined by EPA for each industrial source category. EPA says there are about 400 categories. The Act defines MACT as: "the average emission limit achieved by the best performing 12% of the existing sources ... for categories with 30 sources or more" or, "the average emission limitation achieved by the best performing 5 sources in the category." TABLE 1 SELECTED AIR TOXICS FROM CLEAN AIR ACT LIST IMPORTANT TO MINING INDUSTRY Antimony Compounds Arsenic compounds (inorganic including arsenic)' Beryllium Compounds' Cadmium Compounds Chromium Compounds Colbalt Compounds Cyanide Compounds (dissociation compounds) Lead Compounds' Manganese Compounds Mercury Compounds' Fine Mineral Fibers Nickel Compounds Radionuclides (including radon)1 Selenium Compounds 1Previously listed under NESHAP 2The Administration may not list elemental lead as a hazardous air pollutant.

Jan 1, 1991

By R. D. Peterson

As underground mine operations expand, the ventilation systems supporting them become complex. Complexity increases with periodic ventilation changes. New diagonal connections require a rebalance of resistance to maintain airflow in affected splits in the system. Incidents of mine fires and explosions have occurred in U.S. coal mines when diagonal connections resulting from ventilation changes have resulted in changing airflow directions. MSHA regulations prohibit the reversal of airflow and poor ventilation practice in general, but regulations cannot stipulate or recommend proactive preventative measures because every situation is different. This paper discusses the phenomenon of diagonal branches and recommends practical precautionary measures that can be taken to prevent airflow reversal in planned ventilation changes.

Jan 1, 2012