Search Documents

By Michael A. Trevits

The National Institute for Occupational Safety and Health (NIOSH) in partnership with Strata Products tested the sealing capability of Ventstop®? as part of an ongoing mine fire control and suppression research program. Ventstop®? is a multi-purpose, inflatable device that is produced by Minvent Solutions and is available world wide for use in the metal and nonmetal mining industry. Ventstop®? is also used in the Australian coal industry as a temporary ventilation control device. The device can be quickly deployed, is reusable and can be placed in horizontal and vertical mine voids to control dust, fumes and smoke. Deployment, multi-day inflation and air leakage tests were conducted at the NIOSH Lake Lynn Laboratory to determine the capability and limitations of Ventstop®? in a simulated coal mine setting. During the tests, Ventstop®? was also subjected to low level forces of a nearby methane gas ignition. It is thought that Ventstop®? could be used by the US coal mining industry to temporarily close an underground mine area in response to a fire or spontaneous combustion heating event, to temporarily redirect mine ventilation during longwall equipment moves or during stopping construction. This paper describes this inflatable temporary mine sealing technology and presents the results of the NIOSH tests.

Jan 1, 2009

By Thomas E. Shufflebarger

Glass is one of man's most versatile creations. ---The earliest glaze known---is about 12,000 B.C. ---The oldest pure glass is a moulded amulet of about 7,000 B.C.---. Indicative of a knowledge of properly-proportioned, quality raw-material, means were found for producing the first relatively clear, transparent glass at about the beginning of the Christian era. The fundamentals of almost all the modern, technical processes of manufacture were established during the 3rd Century. (1) Glassmaking, practiced in Colonial America, was moved toward the Ohio Valley in response to increasing demands for fuel. This move, beginning in the 1860's resulted in the use of the glass sands contained in the Oriskany (and St. Peter) sandstone. (2) Glass sand,(3) virtually pure, fine-to-medium-grained quartz sand(4) is the principal raw material used in the manufacture of glass; it constitutes proportions which range to a maximum of about 72% and seldom is glass made without it. However, acceptable glass sands are, invariably, those which most nearly fit the glass-producer's economic needs and any method used to evaluate a raw material's potential must finally prove equatable with such needs. As used in the United States, source-rocks of glass sand include sandstone, unconsolidated silica sands, quartzites and vein-quartz. Admixtures of silica sand and other (principally clay and feldspar), readily separable components have been proven viable. However, the silica sand, refined by nature to a high degree of purity, is the desirable product of exploration. If the term, standard, is justified by long-continued use, the Oriskany - and St. Peter sandstones are, together, the nonesuch of the glass sand industry they provide the principal tonnage of melting sand. According to Grimsley,(5) Ottawa, Illinois, glass-sand is considered the standard glass-sand of the West and the analyses of Berkeley Springs sand (Oriskany) compare most favorably with this sand.

Jan 1, 1974

By Keshavan Nair

In connection with Project Payette, which is concerned with the detection of underground nuclear explosions, it was necessary to determine the technical feasibility of constructing and maintaining a large (approximately 315 feet in diameter) unsupported underground cavity at a depth of approximately 2700 feet in the Tatum Salt Dome in Mississippi. The dimensions and the location of the cavity in the salt dome were governed by criteria laid down by the Atomic Energy Commission. Within the framework of the specified criteria, cavities of various shapes and dimensions could be utilized. One aspect of the feasibility study was to investigate the structural stability of various cavity shapes and to recommend a preferred shape. This paper summarizes the studies that were conducted to evaluate the structural stability of various proposed cavities.(l)

Jan 1, 1968

By Jozef F. Zurawski

River Des Peres Foul water Interceptor (Skinker–McCausland Tunnel) is a gravity sewer tunnel constructed to eliminate dry sewage overflows during high river stages and to improve the wastewater collection and treatment. The original 78-inch (2m)finished diameter Skinker-McCausland Tunnel started as a 21,500 feet (6.5km)interceptor with 13 work, drop and access shafts. The tunnel constructions included soft ground, mixed face and rock tunneling in karst formation with maximum overburden of 175 feet (53m). Due to the success of the project, the tunnel alignment was extended another13,361 feet (4.1 km) and 7 new structures by negotiating two additional segments with the contractor and the designers.

Jan 1, 2001

By M. G. Ayat, J. Dasher

Having an interest in coal slurry pipelines from a decade of arguments with Ed Wasp and crew at Bechtel about pumping thicker slurries slower, I immediately read this article and found nothing in it pertinant to the title. Ayat and Scott pumped five unidentified coals at 9% solids (50%-60% is the area of interest) in a 25-mm (1-in.) pipe around two square elbows through a 76-mm (3-in.) cyclone for up to 60 minutes and sized a large number of samples of unstated size on an unidentified wet screening device. They did not measure power consumption, discharge pressure, flow rate, or give pump tip speed or impeller diameter. They siad the cyclone had a "high" pressure drop (unmeasured) and did much of the degradation (measured) but more or less per unit of energy expended? Hargrove was not measured, so there are no data as to whether it would correlate with degradation. The authors conclude, with no attempt, correlation is "hard to establish." Please experiment before concluding. I am at a loss to know what "increasingly smaller size" means, much less what theory says such particles take "exponentially larger quantities of energy," which the authors neglected to measure. If such experiments without pertinent data or justified conclusions must be published, please attach a pertinant title.

Jan 1, 1990

By E. Arioglu

Y. Luo and S.S. Peng are to be congratulated for their outstanding paper providing new results from surface subsidence monitoring over longwall panels under different conditions. This writer found the authors' paper very interesting. In reference to this paper, the following contributions are offered: • In the paper, the maximum possible subsidence (?Smax) induced by chain pillar convergence has been related to a parameter (h/I -p) by linear regression. (Notations are expressed in this discussion's Fig. I (b).) It is a well-known fact that in a goaf the roof lowers onto broken material that gradually compacts. Then the physical behavior of goaf may closely follow the compaction characteristics of broken materials. In light of this assumption, a mathematical means (Fig. 1(a)) of defining the expected compaction (i.e. surface subsidence) represents an exponential expression between ?Smax/m vs. h/1-p. This is based on Luo and Peng's field observations from the Appalachian, Illinois and Alabama coal fields. (The coefficient of regression "r" under consideration was computed to be 0.883). • According to Wardell's (1969) findings for board and pillar mining, the maximum possible subsidence can be expressed in terms of maximum pillar loading (depth, ratio of extraction) and the height-to-width ratio of the pillars left. Using Luo and Peng's 1991 results, this writer discovered a regression equation between the above-mentioned factors. As displayed in Fig. 1(b), the functional expression approximates as closely as possible the observed subsidence data.

Jan 1, 1992

By Ehsan Alavi, Daniel Cressman, Tatiana Chiesa, Robert Mayberry

The City of Toronto’s Coxwell Bypass Tunnel (CBT) is currently being constructed by North Tunnel Constructors ULC. The scope of the CBT project includes construction of approximately 10.5 km of 6.3 meter finished diameter rock tunnel, five large diameter (20 and 22 meter) storage shafts and eleven tunnel connection drop shafts, along with associated deaeration and adit tunnels. This paper describes progress on the CBT to date and reviews the approach taken in both design and construction of the tunnels and shafts to mitigate risks and reduce cost and schedule of construction.

Jun 13, 2021

By E. M. Wilde

Through the USGS's National Coal Availability program, coal resource appraisals have been completed for three 7.5-minute quadrangles (Willow Crossing, Colstrip East, Colstrip SW) in the Powder River Basin area of southeastern Montana. Available coal reserves (original reserves minus tonnages affected by current restrictions) vary from 44 to 70 percent of the original reserves. Major restrictions impacting each area also vary. In each area, one or two beds contain most of the reserves, but up to eleven beds contain available coal. The main beds in completed studies are the Knobloch, Rosebud, Sawyer and Flowers-Goodale. Three additional areas (six 7.5-minute quadrangles) are in preparation.

Jan 1, 2001

By S. Frimpong

Cable shovels are used for primary excavation in in-situ and/or pre-fragmented formations in surface mining operations. Poorly fragmented hard rock formations and random occurrence of hard boulders in soft formations cause extreme variability of material diggability, resulting in varying shovel stress loading. The stress loading of a shovel’s front-end assembly could result in fatigue failure. Conventional design process, which uses physical shovel simulation studies, is very costly and time consuming for achieving statistically significant results. In this paper, rigid and flexible multi-body dynamic theories are used to develop component stress loading and deformation models of the cable shovel, and solved in the ADAMS/NASTRAN/FLEX environments. Detailed simulation experiments are carried out to examine the performance, reliability, durability and efficiency of the P&H 4100A under varying in-situ formation conditions. The results show areas of high stress fields with a maximum stress of 313.31 MPa at node 441 within the hoist rope. The reliability of the results is confirmed by comparing existing test data. The study is significant because it provides a solid foundation for further study of failure life analysis of the cable shovel components.

Jan 1, 2007

By W. W. Wen

A continuous pilot-scale test of the GranuFlow Process was conducted using a screen- bowl centrifuge for the dewatering and reconstitution of column flotation concentrate at a coal preparation plant in Virginia. In this test, a slipstream of the fine-clean-coal slurry from the column flotation concentrate was treated with a bitumen emulsion before dewatering. The treated products from the screen-bowl centrifuge appeared to be dry and in a free-flowing granular form, while the untreated products were wet, sticky, and difficult to handle. Specifically, test results indicated that the average moisture contents of the dewatered coal were 35.7, 35.5, 32.6, 29.9, and 26.5 wt% with Orimulsion additions of 0,0.7,3.2,4.8, and 6.4 wt%, respectively. The handleability and dust reduction of the dewatered coal product were also vastly improved.

Jan 1, 1997

By K. N. Santini, J. M. Barker

The perlite industry in the United States continued to undergo rapid change and increased competition last year as it did in 2002. U.S. production in 2004 was 510 kt (562,000 st),an increase following five consecutive years of decline (Table 1). Perlite is exported to Canada and to the Pacific Rim. These partially offset imports. Perlite imports from Greece to the eastern and Gulf Coasts of the United States declined by about 22 percent after reaching a record 240 kt (264,000 st) in 2003.But their market remains protected by high rail rates from western U.S. plants. Minor imports of perlite persist by Termolita from Mexico.

Jan 1, 2005

By G. Danko, R. Tiwari, J. Knowles

Many excavation and loading tasks require equipment operators to simultaneously coordinate the motion of multiple machine links, in order to achieve complex tool trajectories. Efficiency, ore selectivity, and machine wear, are all affected by the skill level and attentiveness of the operator. A software-based kinematics reconfiguration system designed to assist operators with various tasks has been implemented on a small experimental excavator using our new differential control architecture. Kinematics transformation and feedback control algorithms are being developed and tested using computer simulation, and the results implemented on the experimental excavator. Several task-specific kinematics transformations, including a virtual revolute-to-Cartesian machine reconfiguration and computer-assisted bucket steering and stabilization have been successfully tested. Progress, challenges, results, expected benefits, and planned work are described.

Jan 1, 2006

By J. C. Heter

The P.W. Gillibrand Company has been processing and stockpiling a suite of heavy minerals at its Soledad Canyon Mine as co-products with construction aggregates since 1984. The heavy minerals are composed of ilmenite, magnetitie, apatite and zircon. The source of the heavy minerals is the Precambrian San Gabriel Anorthosite Complex of the western San Gabriel Mountains. The valuable minerals are readily amenable to standard ore dressing techniques, such as, gravity, magnetic, flotation and electrostatic separation with good recovery and product quality. More than 20,000 short tons of coarse ilmenite were sold in 1990 to the export market for titanium pigment production.

Jan 1, 1992

By E. C. Robertson

D.G. Wilder I found the suggestion that the amount of displacement of a fault can be numerically related to the thickness of gouge or breccia to be both intuitively satisfying and intriguing. I have long agreed that there is some type of relationship between the amount of gouge and the amount of displacement of faults. I congratulate the author for developing a numerical relationship between them. However, I am concerned that the limits for applying this relationship be fully understood. An underlying assumption in this approach is that there is either a uniform thickness of gouge or breccia along a given fault or the thickness does not vary widely. Since it is not always possible to confirm this, the displacements derived by this method should be viewed with caution unless significant fault extent can be observed. At the Nevada Test Site, in drifts constructed in granite for test emplacement of spent nuclear reactor fuel, we found a fault with 0.3 to 0.4 m (12 to 16 in.) of clay gouge. Within a few meters of this location, the fault had no clay gouge, but rather consisted of a highly fractured zone with significantly altered rock and some slickensides. Based on Fig. 1, the 0.3 to 0.4 m (12 to 16 in.) thickness of gouge would indicate a displacement in excess of 30 m (98 ft). However, no gouge thickness would indicate essentially no displacement. Based on a quartz vein that terminated on the fault, and is not identified nearby, an estimated displacement of more than a few meters was made. This estimate is consistent with that obtained using the regression line proposed in the paper if the 0.3 to 0.4 m (12 to 16 in.) thickness for the gouge is used. However, using the regression curves with zero thickness would not yield results consistent with what was observed in the field. Therefore, it is important to recognize that the suggested procedure would properly yield a range of probable displacements. ? *Work performed under the auspices of the US Department of Energy by the Lawrence Livermore National Laboratory under Contract W-7405-Eng-48. Reply by E.C. Robertson It is certainly true that the t (thickness) of gg-bx (gouge and breccia) on a fault does vary along the fault. My observations have been that near the termination of a fault, the displacement d is small and the t is also small, whereas the maximum d and t will usually be found in the central part of the fault. The information on gg-bx and t of the fault found in granite in the NTS tunnel by Mr. Wilder could be interpreted somewhat differently than he does. He speaks of the fault changing within a few meters from 0.3 to 0.4 m (12 to 16 in.) of clay gg to "a highly fractured zone with significantly altered rock and some slickensides," but no gg. The highly fractured rock may be taken to be bx, rock not so finely ground as gg but still crushed by the fault movement, equivalent to the gg in my usage, and probably occupying about the same t. Mr. Wilder's estimates for the fault in the NTS tunnel for t of 0.3 to 0.4 m (12 to 16 in.) and for d of a quartz vein, in excess of "a few meters," would place the point on the low side of the central trend line in my Fig. 1, at the lower limit. There is, of course, a problem with determining d using displacement of only one planar surface. It would be greater or lesser depending on the rake of the movement. Finally, estimating the d of a fault from its t should be made with awareness of our present uncertainties, as pointed out by Mr. Wilder. Although the central trend line in my Fig. 1 has a ratio of d/t of 100, I have put the limiting ratios at 10 and 1000. Understanding of the values of the ratio will be improved only with collection of more data, for which the discussion of Mr. Wilder is much appreciated. G.C. Waterman E.C. Robertson's paper provides significant information to a geologist attempting to deduce fault offset by noting the products of structural dislocation. However, considerable mapping in underground and open-pit mines, and examination of structures produced in different geological settings, have convinced me that gouge and breccia thickness are controlled by geological conditions and fault movement. The following paragraphs suggest geological variables that control them. 1. Depth of Loading A near-surface fault resulting from tensional stress has more breccia/gouge than is produced by a similar stress at considerable depth. A deep-loaded compressional stress may produce a linear zone of schist, or structural dislocation may occur along an earlier formed belt of schist. Such "shear zones" are common in Canadian mines in precambrian rocks. In neither case can offset be directly deduced by an analysis of the minimal gouge/breccia in the shistose rocks. At greater depth, stress may be partially to wholly relieved by flowage. I vividly recall first noting the regional "Midas Thrust" in the Lark mine, Bingham Mining District, UT (where we called the structure the North Fault). My recorded notes, as I remember them, showed a narrow gouge streak separated the `Jordan" and "Commercial" limestone units from impure, muddy limestone beds of uncertain stratigraphic position. The visible structure did not indicate the great importance of this premineral fault

Jan 12, 1984

By K. Chandrasekaran

Carbon-in-Leach (CIL) is conventionally used in gold processing operations when preg robbing components are present in the ore. CIL process is becoming attractive even in other situations when preg robbing is not a factor. This paper discusses the situations in which the CIL circuit can be applied. The results of Leach/CIP and CIL circuits at Newmont's Mill No.2, 4 and 5 are presented for comparison. Newmont's Mill No. 4 was initially designed for a throughput of 4500 tons per day. The mill is presently operating at an average throughput of 7300 tons per day without significant changes to the original design. The design considerations of the Mill No.4 CIL circuit are discussed.

Jan 1, 1991

By William H. Langer

The annual consumption of sand and gravel aggregate in 2006 in the Phoenix, AZ metropolitan area was about 76 Mt (84 million st) (USGS, 2009), or about 18 t (20 st) per capita. Quaternary alluvial deposits in the modern stream channel of the Agua Fria River west of Phoenix are mined and processed to provide some of this aggregate to the greater Phoenix area. The Agua Fria drainage basin (Fig. 1) is characterized by rugged mountains with high elevations and steep stream gradients in the north, and by broad alluvial filled basins separated by elongated fault-block mountain ranges in the south. The Agua Fria River, the basin?s main drainage, flows south from Prescott, AZ and west of Phoenix to the Gila River. The Waddel Dam impounds Lake Pleasant and greatly limits the flow of the Agua Fria River south of the lake. The southern portion of the watershed, south of Lake Pleasant, opens out into a broad valley where the river flows through urban and agricultural lands to its confluence with the Gila River, a tributary of the Colorado River.

Jan 2, 2010

Current scrubber capacities vary from 1.89 to 4.72 m3/s (4,000 to 10,000 cfm), and there is interest in using scrubbers with capacities up to 6.61 m3/s (14,000 cfm). This paper describes research to compare the effectiveness of blowing and exhausting face ventilation systems using high-capacity scrubbers with flows up to 6.61 m3/s. Tests were conducted in a surface ventilation gallery with exhaust and blowing systems operating under similar conditions. The mining machine was equipped with a machine-mounted scrubber. Methane gas was released at constant flow at the mining face and measured at several face locations. Effectiveness of exhausting and blowing systems was compared by determining average face methane concentrations. For each operating condition tested, blowing ventilation was more effective than exhausting for controlling face methane levels. Raising scrubber flow to 6.61 m3/s reduced methane levels for both blowing and exhausting systems.

Jan 1, 1996

By R. K. Mehta

Existing acid mine drainage treatment techniques are not remedial In nature, i.e. though heavy metals can be removed from acid mine water, their presence in tailings and large quantities of these tailings tend to increase capital and operating cost for tailing management. This paper presents the results of a series of systematic tests which finally resulted In the development of the "ferrite" process for mine drainage of coal operations at ambient temperature. The role of pH, temperature, quantity of ferrous salt addition and degree of oxidation is investigated targeting the production of high emu spinel ferrites and effluent water complying regulatory standards with respect to Iron. manganese suspended solids and pH.

Jan 1, 1992

By S. K. Kawatra, H. Haselhuhn

"In many mineral processing applications it is necessary to know the isoelectric points of the various minerals in the ore to properly perform flotation and other mineral separations. However, current zeta potential analysis technology used to determine the isoelectric point of a particle suspension cannot deliver the isoelectric point of each individual mineral, just an average of the mineral system. Traditionally, individual isoelectric points have been gathered by testing pure, synthetic minerals. These values can vary widely depending on the mineral synthesis procedure and the water quality used during the isoelectric point analysis. A more robust approach for determining the actual isoelectric point of a particular mineral in a mixture of minerals is needed. This paper details a method for determining the isoelectric point of an iron oxide mineral in a siliceous iron ore. The method uses a laser scattering particle size analyzer and a pH electrode to determine the pH at which the liberated mineral particles begin to flocculate as pH is decreased. The pH at which the average particle size rises dramatically is the isoelectric point of the mineral with the highest isoelectric point in the ore. This measurement technique was used on natural hematite, goethite and siderite ores as well as a synthetic mixture of pure silica and pure hematite. The results for synthetic hematite mixtures were comparable to literature values.IntroductionRecently there has been an increased interest in the processing of low-grade iron ores (Bolen, 2014; Carlson and Kawatra, 2008, 2011, 2013; Halt et al., 2014; Halt and Kawatra, 2014; Haselhuhn 2012, 2013; Haselhuhn et al., 2012a, 2012b; Kawatra and Halt, 2011; Liu et al., 2014; Manouchehri, 2014; Sandvik and Larsen, 2014; Semberg et al., 2014). The zeta potential of iron ore minerals is a very important and often overlooked aspect of iron ore mineral processing. Zeta potential is the charge at the shear plane of a surface in an aqueous environment (Carlson and Kawatra, 2013). Many ores consist of a variety of minerals differing in zeta potential. This property of a particle surface in water is responsible for either keeping the particles dispersed from each other or flocculated to each other. This is important during many operations such as flotation, desliming and thickening. Zeta potential is primarily a function of the pH of the water and the mineralogy of the particles, though certain ions within the water can also have a significant impact (Haselhuhn, 2012). Consider the following situation: silica (SiO2) particles and hematite (Fe2O3) particles are suspended in an aqueous solution. These two types of minerals have drastically different zeta potentials throughout the pH spectrum (Esumi et al., 1988). In alkaline conditions, both types of particles exhibit negative zeta potentials and will tend to disperse from each other. In acidic conditions (between pH of 3 and 6), silica has a negative zeta potential while hematite has a positive zeta potential, so these surfaces will tend to be attractive to each other and the particles will flocculate and settle. This phenomenon is visually described in Fig. 1. The pH at which the two minerals begin to attract to each other, or destabilize, is near hematite’s isoelectric point. The isoelectric point is defined as the pH at which the surface has a net zero zeta potential (Carlson and Kawatra, 2013)."

Jan 1, 2015

By G. Deschênes

Following a successful investigation on the Central Zone sample, a cyanidation study was conducted on an ore sample from the AD-MW Zone of Clarence Stream Property, owned by Freewest Resources Canada, to develop a leaching strategy to extract gold. At a grade of 6.48 g/t, gold is present in the forms of aurostibite, free gold and electrum. The ore contains 4.3% berthierite/gudmundite, 1.3% pyrrhotite, 0.7% pyrite, 0.07% stibnite and 0.9% arsenopyrite. Similar to the Central Zone, the extraction of gold from the AD-MW Zone can be performed at atmospheric pressure, pH 10.5 and with a low concentration of cyanide. The grind size had no effect on gold extraction between a P80 of 28 to 71 µm. The oxygen and cyanide requirement significantly increased with a ?ner grind. Consequently, a very close control of cyanide addition is required to minimize passivation of gold. Lead nitrate, added in the pretreatment, increased the extraction of gold by 2.3%. Leaching at pH < 10 improved gold extraction but increased the cyanide consumption by 5%. Passivation of gold occurred when the pretreatment was longer than 2 hours. A longer pretreatment reduced the cyanide consumption by 5%. Mineralogical characterization of the leach residue with no gravity pretreatment prior to leaching indicated the presence of unleached gold grains and passivated gold grains. Removal of coarse gold by gravity increased the extraction by 2.8% (leach residue at 0.74 g/t Au). Increasing the DO to 16 ppm or the lead nitrate from 500 to 1,000 g/t increased the overall gold extraction to 90.4% (leach residue at 0.62 g/t), which is the maximum gold extraction obtained. The leaching parameters were 800 ppm NaCN, DO 16 ppm and pH 10.5 for a duration of 120 hours. The associated cyanide consumption was 4.0 kg/t. Gold leaching was not sensitive to cyanide concentration. Reducing the cyanide concentration to 250 ppm resulted in a gold extraction of 89.5% with a cyanide consumption of 2.6 kg/t.

Jan 1, 2009