Search Documents

By J. A. Cole

This paper discusses the modification of the cyanide tailings treatment method from ferrous sulfate to Caro's acid (peroxymonosulfuric acid). An examination of the operating parameters, costs, and chemistry describes how the decision was made to switch to this treatment method. Plant data collected from the last several months will be used, along with considerations from an operator's viewpoint.

Jan 1, 1996

By Lida Sun, Na Wu, Mengyang Huang, Xingxiang Fan, Yan Jiang, Shasha He, Kunbin Yang, Yang Cao

The separation of lead (Pb) and mercury (Hg) from copper (Cu) smelting acid sludge using the carbonization and acidleaching total hydrometallurgical process was investigated. The effects of the excess coefficient of sodium carbonate, excess coefficient of nitric acid, conversion time, conversion temperature, dissolution time, and dissolution temperature on the separation efficiency of Pb and Hg were studied. The test results indicated that when the dosage of sodium carbonate was 2.0 times the stoichiometric ratio, the conversion time was 1.5 h, the conversion temperature was 75 ℃, and the amount of nitric acid was 1.8 times the stoichiometric ratio. Additionally, the dissolution time was 1.0 h, the dissolution temperature was 60 ℃, the ratio of liquid–solid was 5:1, and the separation efficiency of Pb and Hg was 98.72%. This study demonstrated the advantages of a short, simple, and environmentally friendly process for separating Pb and Hg from Cu smelting acid sludge, providing complete separation and introducing a new technology.

May 30, 2024

By A. A. Schweizer

Buckhorn ore is hydrous, argillized basaltic andesite, and is at least 60% clay composed of kaolinite and subordinate montmorillonite. Moisture content runs from 10% to 25%. The original crushing plant was a typical compression type, employing a jaw crusher, and two cone crushers. The system was plagued with constant plugging and unable to meet production plans. The three compression crushers were replaced with a Stamler Feeder Breaker followed by a Hazemag Impactor. Production plans are now exceeded. Agglomeration has progressed from an agglomeration drum to cascading conveyors, to introduction of the lime and cement into the primary crusher.

Jan 1, 1987

By Francesco Chiappalone, Franco Gasperin, Fabrizio Fara

This document describes the challenging task of mining through tiebacks using a 21'-8" diameter Tunnel Boring Machine (TBM) as part of the Ship Canal Water Quality Project. The mining operation involves navigating through 17 tie-backs that are evenly spaced at 8-foot intervals, with many intersecting the full face of the cutterhead. Detailed analysis and review of TBM parameters specific to this area have been conducted to ensure operational efficiency and safety. Hyperbaric interventions have been planned and coordinated, encompassing pre-mining preparations, continuous monitoring and adjustments during the mining process, as well as post-mining measures. The document highlights the complexity and importance of strategic planning and execution to successfully overcome the tie-back intersections during the mining operation.

Jun 23, 2024

By E. M. Frizzell

An ongoing research program at the Spokane Research Center of the U.S. Bureau of Mines is directed toward investigating drilling parameters (thrust, torque, penetration rate, and drill revolutions) during the drilling of roof bolt holes. A system that measures these drilling parameters calculates the specific energy of drilling, and determines drill bit position has been developed by the Bureau and mounted on a roof bolting/drilling machine, through the use of a microcomputer, critical drilling parameters can be immediately interpreted and analyzed. This makes it possible to inform the operator of hazardous roof conditions. Initial results of this program are presented here.

Jan 1, 1990

By U. Paschedag

Today's modern longwalls have to produce high outputs with maximum availability and running time with the additional requirement of ever increasing panel width and length high-performance face conveyors require intelligent solutions for the integration of drive systems and chain tensioning devices into the overall longwall automation. The fully automated chain tensioning system allows the operation of an AFC with optimum chain tension at all times regardless of actual load on the conveyor. For the heavy-load start-up, the accurate load-sharing and an efficient overload protection of modern AFC's WESTFALIA and Dodge jointly developed the integrated WB/CST drive system.

Jan 1, 1995

By Jr. Wilkinson

Mine planners are under pressure to evaluate the impact of changing economic times and newly acquired data on the mine plan. Incorporating change, such as commodity prices, customer sales, changing cost assumptions, and newly acquired geologic data into the mine plans requires quick turn-around for model building and planning to keep the mine plan on pace with changes as they are occurring. Because of the length of time required to perform some of the geologic modeling and mine planning tasks, planning frequency may not be keeping pace with the frequency of change. This paper discusses how one company has increased the frequency rate and accuracy of mine plans to keep current with incoming data, ensuring mine plans reflect the latest information, thereby minimizing or eliminating production cost variance.

Jan 1, 2010

By Michael McNinch, LaTasha R. Swanson, Jennica L. Bellanca, Justin Helton

As manufacturers and mine operators develop and implement proximity detection systems (PDSs), they need to be mindful of the systems’ compatibility with mineworkers’ tasks, and possible unintended consequences. Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) interviewed mineworkers at mine sites that currently use or previously have used PDSs on mobile equipment, including shuttle cars, battery haulers and scoops. Mineworkers reported that mobile PDSs affect loading, tramming, section setup, maintenance and general work on the section. Mineworkers discussed the operational effects and increased burden, exposure and risk. Mineworkers also suggested that improved system task compatibility, training, logistics and PDS performance might help address these issues. Manufacturers and mine operators implementing this or similar technologies may also consider mitigating task incompatibilities up front, performing additional site-specific usability testing and restricting the use cases of the system to improve performance.

By Q. Xu

The new process consists of the selective coalescence of fine hematite particles by fine magnetite. The gangue minerals are dispersed by some dispersant; thus it can be separated by desliming. This process is particularly suitable for fine-grained hematite/magnetite-type deposits.

Jan 1, 1989

By J. D. McKay

The Bureau of Mines devised a column flotation technique using either fine or coarse bubbles and compared it with conventional flotation on a Montana chromite ore. On deslimed ore, fine-bubble column flotation produced a 44.7-pct-Cr203-grade rougher concentrate with 87-pct recovery, compared with 43.8- and 43.5-pct-Cr203-grade rougher concentrates with 85- and 77-pct recovery for coarse-bubble column flotation and conventional flotation, respectively. On undeslimed ore, coarse-and fine-bubble column flotation produced rougher concentrates containing approximately 41.5-pct-Cr203 with 95-pct recovery, exceeding conventional flotation which produced 35.6-pct-Cr203-grade concentrates with 87-pct recovery.

Jan 1, 1985

By R. A. Jankowski

The U.S. Bureau of Mines has conducted a study to identify the sources of respirable dust and appropriate dust controls applicable to today's high tonnage longwall faces. The primary source of respirable dust identified is the cutting action of the shearer; however, the pct contribution of dust from coal transport through the stageloader/crusher was significant. This was primarily due to the high rate of mining, requiring rapid and constant coal transport. Techniques implemented for the control of shearer-generated dust included high drum water flow rates, deep cutting, shearer-clearer-type external water spray systems, and radio-remote control. The high water flow rates, and an enclosed stageloader with scrubber, were used to control dust during coal transport. No novel or effective control technology exists to control dust during support advance. Administrative controls for dust avoidance, and manual and batch-activated electro-hydraulic control systems were used to keep support movers out of the dust generated during support advance.

Jan 1, 1990

By B. M. Davis

Characterizing exploration prospect potential has aspects that differ from those encountered during ore reserve estimation. One problem is determination of the ore reserve potential prior to acquisition of significant volumes of hard data. The evaluation is subjective and data are usually sparse and of uncertain quality. However, estimations of the ore reserve potential are commonly demanded by management before project funding will be approved. The estimations from several prospects, along with the uncertainties inherent to the estimation, are then used to compare and contrast the potential of several prospects, often with widely varying geologic models.

Jan 1, 1990

By D. Kump

The Bullfrog Mine is an underground gold mine that uses the underhand-cut-and-fill mining method. The portal was established on June 18, 1991. Mining is expected to be completed by the summer of 1999. This paper starts by discussing what it took to get from nothing to 2000 tons-per-day backfill, and ends with a hindsight commentary on things that did and did not help.

Jan 1, 1999

By Jay P. Chapman

The basic control requirement for multi-pump, long distance slurry pipelines are discussed and a particular example of an operating slurry pipeline using programmable controllers is presented.

Jan 1, 1983

By Ralbern H. Murray

Typical First Year Selling Price Strip Mined Western Sub-Bituminous Coal Based [Fixed Capital (1) $600 MM Construction Loan Interest $100 Working Capital $ 30 Start-up Costs $ 30 Total Capital Requirement $760 MM Annual Costs (First Year) $M/Year Coal (2) 443,550 Operating Costs(3) 53,000 Depreciation(4) 36,500 Interest(5) 45,220 After Tax Profit(6) 34, 200 Federal Income Tax (48% Rate) 31, 570 Gross Revenue Required 245,040 (Less) By-Product Sales (18, 000) Net Revenue Required 227, 040]

Jan 1, 1975

By M. Jaramillo

The Expanded West Pit of the 15 MTY El Cerrejon Mine will reach a maximum depth of270 m. Slope stability evaluations indicated that this depth, combined with structural complexities, would create a serious risk of footwall instability. Stabilization call for anchoring the footwall by installation of cable bolts, 9 to 33 m long, of multi-strand steel cable. For each of the 15 m high mining benches, a row of bolts is installed with variable horizontal spacing, depending on dip magnitude. Cable bolting is now standard operating practice and 11800 bolts will have been installed during the life of the mine.

Jan 1, 1995

By Peter Amelunxen, Brandon Akerstrom

Since its introduction 40 years ago, the compartmental model of flotation has been used to predict the performance of mechanical flotation cells. However, it has found limited success for modeling dual-chamber machines and, as a result, engineers have adopted empirical correction factors usually derived from field audits of industrial cells to predict the performance of dual-chamber flotation cells. This paper introduces an extension of the compartmental model that applies to both single- and dual-chamber cells. The model is tested against pilot test work performed at Capstone’s Pinto Valley concentrator, and then used to evaluate the key operating and design parameters of dual chamber flotation cells. The results suggest that the design of the mixing chamber — for example, whether it is pneumatic or mechanically agitated — is not a significant contributor to overall machine performance. The work also suggests that the highest recoveries are achieved when the froth recovery is high, and longer separation chamber residence times and/or higher internal circulating loads are only beneficial when the froth recovery is low. Lastly, the results show that the single most important driver of the machine performance is the froth recovery of the separation chamber.

Mar 1, 2025

By F. D. Wang

This paper presents an innovative mining method with the application of the water jet. The basic principle of this mining method is to mine a thin panel slice with a water jet system and to allow the roof to deflect elastically and subsequently to be supported by the coal floor without artificial roof support. Through the sequential mining of layers from top to bottom, the entire seam is extracted and the roof rests upon the mine floor. The advantages of this method are that the safety of underground operation can be greatly increased and the surface overburden disturbance will be markedly reduced. . An economic evaluation of such a system is presented for the total cost estimated per ton of coal mined at the face. This evaluation is then compared to that of a continuous mining section utilizing a room and pillar mining method.

Jan 1, 1991

By David L. Martin

This paper discusses the development of a SLAM II* simulation model with imbedded optimization modules designed M evaluate mineral exploration and exploitation strategies. The model traces through a sequential exploration program, evaluating each deposit site based upon geologic information and potential profitability of the site. At a specified time during the simulation, a new production plan is developed for currently producing deposits which takes into account the planning horizon and deposits which are currently being explored. Potential uses of the model by geologists, engineers, and management decision makers include setting corporate objectives and policies on exploration and production. The model is also useful for testing past decisions to evaluate decision making criteria and evaluating mineral deposit profit potential.

Jan 1, 1983

By V. E. Cole

For the successful execution of a major project, the project team must be thoughtfully organized, manned, instructed and motivated. This is true of both the engineer/constructor team and the mining company team. Then these teams must be carefully related so that they function effectively as one organization on the job. This paper describes the organizing techniques and the human ingredients and know-how of a successful project.

Jan 1, 1980