Search Documents

By D. Bristow, D. Baker, K. Awuah-Offei, A. ur Rehman

While a body of work exists on intelligent systems for guiding occupants out of buildings during an emergency, the problem of guiding miners out of a mine during an underground emergency has not been explored. Underground evacuation fundamentally differs from building evacuation because of differences in the regulatory regime and uncertainty regarding the number of occupants. The potential for implementing an intelligent miner guidance system is buttressed by the fact that miner tracking systems, along with communication and sensor networks, already exist in underground mines. This work presents a method based on a local positioning system, in the form of a network of “nodes” at major “intersections,” which can then be used to guide miners to safety. We have developed a path-planning algorithm, based on Dijkstra’s algorithm and the local positioning system that can provide miners with the optimal escape path in an emergency. The algorithm is validated with scenarios at the Missouri University of Science & Technology Experimental Mine demonstrating the potential to include smart technology in mine emergency management and response planning. INTRODUCTION Underground mines are hazardous environments with a higher than usual risk of safety emergencies where miners have to evacuate the mine to save their lives. Mines have always trained miners to evacuate or shelter-in-place in minimum time. Jalali and Norrozi (2009) opined that the three major components that help miners in case of emergency are pre-planned optimal escape routes, decreasing delays, and improving the education of miners. In fact, Goodman and Kissel (1990) suggested that fatalities arising from mine accidents could be reduced by 50% just by decreasing delays in finding the pathways in case of emergency. The proposed work can assist miners in finding escapeways quickly in case of emergency. It is very important to have a pre-planned evacuation strategy that is clearly communicated to miners to ensure the safety of all (Conti, Chasko & Wiehagen, 2005).

Jan 1, 2019

By W. R. VanSlyke

Scrubbing is gaining increasing recognition as a valuable tool in the treatment of Mesabi Range intermediate iron ores. In general, the earliest washing plants included log-washers in their various flowsheets. While log-washers certainly did impart a degree of scrubbing to the crude ore, such treatment bears little resemblance to the type of scrubbing being practiced today. At the time that these early plants were erected, only the true wash-ores were being processd. ("Wash-ores" are defined as crude ores in which relatively coarse chunks of almost completely liberated iron are found in a matrix of loosely-consolidated fine sand.) To treat ores of this type, sizing at approximately 65 to 100 mesh was sufficient to produce a merchantable concentrate. As crudes were being treated in which there was little "locking" of iron and silica, log-washers tended to disappear and large screens and classifiers took their place in Mesabi range flowsheets. The "screening and classification" type of flowsheet 'had its greatest usage in the 1945-55 period, generally speaking. During this same period, many operators found it necessary to supplement the "wash-ore" type flowsheet with heavy-media treatment.

Jan 1, 1959

By G. Soni

A first principle flotation model has been derived from the basic mechanisms involved in flotation. The model consists of a series of analytical equations for bubble generation, bubble-particle collision, attachment, detachment, and froth phase recovery. The model can predict flotation from both hydrodynamic and surface chemistry parameters such as bubble size, particle size, energy dissipation rate, ?-potentials, contact angles (?), etc. The model has been validated in a series of laboratory batch flotation experiments, in which mono-sized glass beads are used as feeds. The experimental results are in good agreement with model predictions both in terms of grade and recovery.

Feb 23, 2014

By C. Garcia, J. J. Opazo, A. Potulsha, T. Comi

"Sierra Gorda SCM is a joint venture partnership of KGHM International (owned by KGHM SA, Poland), Sumitomo Metal Mining and Sumitomo Corp. (Japan) operating in northern Chile. The Sierra Gorda openpit mine and coppermolybdenum processing plant will become one of the largest mines in the world. The need for optimum production efficiency and sustainability has driven the creation of the most modern, wellinstrumented mine in Chile. This article contains a general review of the project including geology and history.This was a fast-track project going from greenfield site acquisition to mill startup in 10 years. Highly experienced and motivated engineers and technical staff have overcome many significant challenges resulting in a rapid ramp-up of production capacity. A potential expansion to double the production rate in the fourth year of operation has also been intensely studied.The Sierra Gorda property is located in the Atacama Desert of northern Chile, in the District of Sierra Gorda, Region II of Antofagasta, Chile (Fig. 1). There is almost no precipitation in this area. The mine site is generally flat with some rolling hills. The project is located about 5 km (3 miles) from the village of Sierra Gorda at an elevation of approximately 1,700 m (5,600 ft) above mean sea level. The village is near a highway and railway line. The city of Calama, home of the famous Chuquicamata Mine, is located about 60 km (37 miles) northeast of Sierra Gorda. In addition, the SG mine is in the midst of numerous other mines including Spence, Esperanza, Mantos Blancos, El Tesoro, Lomas Bayas, Gabriela Mistral, El Abra, Radomiro Tomic and Escondida, to name a few.The primary organizational value at Sierra Gorda is "Zero Harm." This includes employees, contractors, the environment, the community, plant facilities and mine equipment. A cornerstone of this program is called 5X5S (five by five S), which combines the lean principles of 5S with the safety model of taking five steps back and thinking about the task at hand for five seconds, five minutes, the time it takes to assess and manage the risk. "People caring about people" promotes proactive engagement in the safety of coworkers and others at work and at home."

Jan 1, 2014

By M. Albrecht

In the mining industry and particularly in the processing plants, we use some large and unusual equipment. Understanding what it is and what it does is important to good operations, but how do you teach a new employee. When I started out in this field, the information on the processing equipment was easy to come by. Equipment manufacturers readily supplied it; their salesmen, often engineers themselves, knew how important the availability of this information was. Old engineers used their notebooks to train the new engineers. Over time this has changed. Equipment manufacturers have changed hands or gone out of business, and often the older engineers are gone. As a start in reversing this, this presentation will be an introduction to sizing, selecting, and operation of some of this equipment, in particular gravity separating equipment. Major portions of this have been excerpted from A Mining Engineers Notebook: Mineral processing (2).

Feb 23, 2014

When I wrote the Railroad portion of "Mining Engineering" magazines 94 Powder River Basin (PRB) Coal Article I described to you some definite destinations the Railroads had in mind. As with many destinations, the ones I wrote of turned out to be merely stops on the way to places that we have yet to reach. Somewhere along the way we discovered that making it better is a continuous process not just something that you can do in phases I, II, III, & IV. We always knew this I suspect, but perhaps not at the awareness level that exists in RR environments in 1997. The purpose of this article is to update the 94 article, which I could do very quickly. Everything I told you we were going to do in 94 is done, end of story! But in addition to making it a very short article it would not be telling you the things RR has done beyond what we were planning in 94 and for the future.

Jan 1, 1998

By R. Kahrger

This paper is written to convey the latest developments in compact bucket wheel excavators (BWE's) operating in medium-hard rock and will serve to indicate that BWE and compact machines in particular do in fact have application in materials other than loose sandy soils and soft rock. A recently run extensive three month field test in hard marl, which was previously considered too hard and difficult to be handled by a BWE, is used as an example to explain some of the design requirements and problems associated with digging harder materials.

Jan 1, 1990

By Thomas Schwind, Benedikt Grau, Angelos Gakis

"In Crossrail’s Farringdon station, compensation grouting was successfully utilized to mitigate the surface settlements induced by the tunneling works. The main focus of this study was the platform tunnels, which were approximately 300m long each and were enlarged to platform size using sequential excavation method (SEM) from the existing TBM running tunnels, initially supported using sprayed concrete linings. The rear grouting injections were carried out at a typical distance of minimum 5m above the completed, fully strengthened shotcrete lining hence inducing some additional stresses. In-tunnel monitoring using surveying targets was performed systematically to ensure that no excessive distortion of the initial shotcrete lining occurred. 3D finite element analyses were utilized to back calculate the actual “effective” pressure that was imposed on the completed shotcrete rings against the additional measured in-tunnel displacements due to the compensation grouting episodes. Additionally an assessment of the theoretical, “maximum” allowable grouting pressures that would lead to overstressing of the lining is presented. INTRODUCTION As part of the back analysis performed for the SEM tunnels in Farringdon station, an investigation of the effect of compensation grouting on the two constructed platform tunnels was undertaken. The platform tunnels were 10.6m high by 11.4m wide and approximately 300m long each. They were enlarged to their final shape from the existing TBM tunnels using SCL methods. This study utilized 2D and 3D finite element (FE) analyses in order to back calculate the observed tunnel crown displacement, assessing the equivalent grouting pressures during the rear injection episodes of the concurrent grouting operations. The results provide a useful reference for the order of magnitude of the grouting pressure load cases that can be applied in the numerical simulation of similar cases. Part of the results presented in this paper, were derived by the second author as part of his Master of Science thesis in Technical University of Graz."

Jan 1, 2016

By Ian Sherrell, Christian Cardoso, Henri Vepsäläinen, Guillermo Bermudez

Performance of mixing mechanisms in flotation cells is paramount, as inefficiencies can lead to financial losses through valuable minerals lost to tailings. Technological advancements have been implemented in flotation cells to optimize performance, but regardless of the efficacy of these developments, room for improvement may persist. Since its launch in 2005, FloatForce® has set a high industry standard for flotation mixing mechanisms. However, current mining trends call for sustainability-driven developments while improving metallurgical performance. Metso has recently introduced FloatForce®+, the latest iteration of FloatForce, developed through extensive laboratory, pilot, and industrial testing, aligning with mining sustainability trends. It has been designed to maximize recovery, reduce power draw and optimize manufacturing materials. This development stems from a redesigned rotor profile paired with a harmonizing stator configuration. This paper presents the development journey of Metso’s latest patented flotation mixing mechanism, an advancement to improve metallurgical performance at a high sustainable standard in flotation cells. The theory, CFD modeling and test work are discussed in detail.

Feb 1, 2025

By V. Kecojevic

The objective of this research was to establish the relationship between production, consumption and energy cost in the surface mining of bituminous coal. Specific energy sources such as diesel, gasoline, electricity, explosives and bituminous coal were considered in this study. Gain in net energy, proportion of the cost of energy consumption and total energy cost relative to total revenue of extracted coal were determined, and a new energy efficiency index and a new energy-cost ratio were established. A case study on an operating surface coal mine was carried out to demonstrate the application of the newly developed method. The results of this study can be used by the mine operators in establishing strategies for the optimization of energy production and consumption, and for reducing the cost of bituminous coal extraction.

Jan 1, 2014

By John T. Langstaff

Rock bursts in the deep metal mines of the Coeur d’Alene district present an ever increasing problem in the safe and economic mining of the district’s silver, lead and zinc ores. Hecla Mining Company operates two mines in the district - the Star, a 1100-ton/day lead-zinc mine, and the Lucky Friday, a 750-ton/day silver- lead mine. Rock burst problems at both operations prompted Hecla management to make an all-out attempt to find a practical method of predicting and eventually controlling these bursts. Research by personnel from the Denver Research Center of the Bureau of Mines at ASARCO's Galena Mine indicated that a recognizable pattern of seismic activity preceded some bursts and this activity could be precisely monitored by present- day, off-the-shelf electronic devices. Using information gained by the Bureau and other sources, Hecla designed and installed a 24,- channel seismic monitoring system in the Lucky Friday mine. Installation was completed in December 1973 and after a year of successful operation, it was decided that a similar system would be installed in the Star mine. This second installation was completed in June 1975. Both systems are now operating and providing continuous information on underground seismic activity. Each monitoring system consists of a network of geophones with attendant amplifiers that are connected by shielded cable through an interfacing device to a computer. The origin of each seismic event is determined by the computer and a three-dimensional location is printed out. This information is plotted daily and is used to pinpoint rock burst prone areas and chart their relative seismic activity. This paper will review the causes and effects of rock bursts in the Coeur d'Alene district, the equipment and operation of the microseismic system at the Star and Lucky Friday mines, and the results obtained to date.

Jan 1, 1977

By A. Datta

An appropriate scale-up methodology is very useful for ball mill design and optimization of the grinding circuit. To date, the scale-up is based on the selection and breakage function model using lab mill data. However, a major drawback of that approach is that the charge motion in a lab mill is vastly different from that in a large industrial mill. Therefore, in the methodology proposed here, first the energy of individual collision in the mill is computed employing the discrete element method (DEM). Then the breakage of particles as a function of collision energy is studied in a separate experiment. Together, this information constitutes what is known as collision energy based population balance model. The appropriateness of this model is shown for different batch grinding mills.

Jan 1, 1999

By D. W. Park

Longwall mining is popular in underground coal production in the United States due to higher production rates and safety concerns. Because of the extreme complexity, it is necessary to plan an adequate design to achieve a safe and efficient working place. The proper sizes of yield and abutment pillars and panels can be determined by simulation using numerical modeling techniques. By means of three-dimensional modeling, stresses to be imposed on the pillars, panels, gob, and powered supports can be analyzed. In this study, an initial three-dimensional finite element model was developed and then modified into four different models. Using these models, the numerical outputs of distributed stresses on three different sizes of yield pillars, three different sizes of panels, and two different sizes of abutment pillars were compared and analyzed to determine the most adequate pillar and panel sizes. Progressive failure theory based on the Hoek and Brown failure criterion was used to determine redistribution of stresses in the yielded and failed areas in the longwall mine.

Jan 1, 1992

By F. Varley, J. Whyatt

A variety of dynamic failure cases with regional impact were described at a bump symposium held in 1958. These types of events, while rare, are of particular interest because their ability to impact a large area has disaster potential. These cases can be grouped into two broad classes of events by mechanism. These are (1) a slip along steeply dipping faults and (2) the fracturing of strong strata above or below the coal seam. Both failure modes produce dynamic or “shock” loads on the perimeter (roof, rib and floor) of mine openings. Special consideration should be given to these failure modes in the planning of deep coal mines, since their occurrence is not within the professional experience of many contemporary workers. In addition, their potential is not evaluated by many of the analysis tools commonly used to evaluate hazards in coal mine plans.

Jan 1, 2009

By A. D. Pernichele

Four types of slope failures in waste dumps are recognized; debris flow, foundation failure, edge slump and blowout. The first three types, although at times causing considerable damage to property and interfering with mine operations, are not usually dangerous to personnel because of their slow rate of movement. The fourth type, the blowout, is considered to be the most dangerous because of its explosive mode of failure and lack of forewarning. The December failure at Verona dump is presented as an example of a blowout. Data from piezometer holes indicate that the blowout was due to perched leach solutions near the face of the dump. The level of water in this zone is very closely related to the rate of leach water application on the dump. A detailed analysis of core samples indicated that the impounded water was due to a zonal accumulation of Jarosite which is associated with a buried dump surface. Drain holes proved successful in controlling perched leach solutions in the critical zone near the face of the dump. Monitoring of the water level in the perched zone is considered essential in preventing blowouts. The use of drain and piezometer holes has allowed an increase in the rate of water application on the dump while preventing additional failure.

Jan 1, 1971

By C. J. Greet

Grinding with an electrochemically inert grinding media (i.e., high chrome white iron) shifts the pulp potentials to more oxidising conditions, increases the dissolved oxygen content and reduces the EDTA extractable iron concentration when compared with milling with electrochemically active grinding media (forged steel). These changes in pulp chemistry produce cleaner particle surfaces, reduce reagent consumption, and increase concentrate grades and recoveries. This paper presents a robust laboratory test program that not only demonstrates the changes in the pulp chemistry, but also provide an indication of the magnitude of the metallurgical improvements that are possible. While laboratory studies are interesting, the proof is in the pudding! So, the paper provides an overview of plant trials conducted at several porphyry copper operations around the world: Newmont’s Cadia and Red Chris Operations, as well as Evolution Mining’s Northparkes Operation. These successful plant trials clearly demonstrate that selection of the right grinding media alloy will yield savings in grinding media consumption and reagent consumption as well as increases in revenue through improved copper and gold recoveries. However, many of the porphyry copper mines on the Eastern Pacific are copper-molybdenum deposits. The paper presents laboratory test results for typical copper-molybdenum operations and extrapolate these numbers to what might be expected should a plant trial occur.

Feb 1, 2025

By K. Lang

The use of high-efficiency electrical submersible pumps (ESPs) for large scale, open pit mine dewatering operations provides a good example of how technology, products and services from the oil and gas industry can be adapted to the mining industry. In this case, the mine is Goldcorp?s Peñasquito in the Zacatecas state of Mexico, at the Peñasco and Chile Colorado open pit deposits. The technology, products and services are from Schlumberger artificial lift (AL) and Schlumberger industrial water services (IWS). Overview of high-efficiency ESPs This section provides a brief description of the basic components, specifications and operating capacity ranges for the ESPs compared with traditional or conventional dewatering well pumps. This information helps to establish how ESPs provide certain functional and economic advantages over conventional pumps in a mine dewatering application. A schematic of a high-efficiency ESP in an oil and gas (O&G) application is shown in Fig. 1.

Sep 1, 2013

By Y. J. Wang

In the mathematical analysis of electrical networks, the electrical devices are often modeled using idealized network elements such as current sources, voltage sources, and resistors. An analogous approach is outlined here for the modeling of mine ventilation networks, which can be considered nonlinear resistive networks. The modeling technique proposed uses five basic (non-reducible) elements: the H element, the Q element, the D element, the R element, and the N element. These elements are characterized by their (a) pressure gain or loss, (b) air quantity, and (c) pressure-versus-quantity relationship, each of which may be known or unknown. In addition to the definition of the basic elements, the necessary conditions for which there exists a unique solution are discussed. This is performed using theoretical developments derived from electrical circuit theory and illustrated in example networks. The proposed procedures are useful in the solution and characterization of mine ventilation networks.

Jan 1, 1996

By John Kuyt, Zili Li, Michael Mooney, Michele Mangione

"INTRODUCTIONTwin bored tunnels are commonly used for a variety of road and tunnel projects throughout the world. A major component of these twin tunnel projects is the construction of connecting cross passages that provide emergency access between tunnels and space for tunnel service equipment. Cross passages can present significant geotechnical risk and technical challenges to a project – support systems must be considered for redistributing loads around the mainline tunnel openings and supporting new loading resulting from excavation activities. Additionally, cross passages pose risks to construction schedule and cost because of their sequencing at the end of construction, so mitigation of schedule overruns can be critical. By observing field instrumentation data records from completed projects, a betterunderstanding of the force development in each temporary structure can be achieved with indication of which structures are the most critical to support ground loads.This paper discusses the data obtained during the Brisbane Airport Link construction project, a road tunnel located in Brisbane, Australia. Strain gauge instrumentation data from the precast segmental lining and propped opening steel sets is presented with relation to the construction sequence and local geology. Interpretations and conclusions based on the observed trends are proposed, with several key mechanisms affecting the loading and unloading identified.Brisbane Airport Link Project OverviewThe Brisbane Airport Link project in Brisbane, Australia, connects central Brisbane to the airport located northeast of the downtown with over 7km of twin-bore road tunnels, two lanes each, with several caverns, interchanges, and access ramps constructed along the alignment to connect to other key routes in the city. The project was executed under a Public-Private Partnership (P3) scheme, funded and operated by the consortium BrisConnections. The main contractors were a joint venture of John Holland and Theiss, while the design was carried out by Arup and Parsons Brinckerhoff.Construction of the tunnels was conducted using a combination of 17 roadheaders and two 12.5m double-shield Herrenknecht TBMs [1]. The TBMs were used in EPB-type closed mode for the initial portion of their drive, starting at the northeast end of the alignment. Tunneling started in soft ground, weathered rock, and mixed face conditions initially, progressing to competent sedimentary rocks as the drive continued. Support was accomplished using a 12.1 m diameter steel fiber reinforced concrete (SFRC) segmental lining installed behind the TBMs in a 9 segments + 1 key arrangement. The innovative design of these segments is detailed in the paper by Harding and Francis [2]. Ancillary roads and underground interchange caverns were constructed by sequential excavation techniques using roadheaders, accounting for nearly half of the total underground excavations."

Jan 1, 2016

By Georgene Renner, Chee Theng, William Gleason

"With more than 900 booth spaces sold and 630 exhibiting companies displaying their wares, there was something for all 7,804 attendees on the exhibit floor of the 2015 SME Annual Conference & Expo in Denver, CO Feb. 15-18. The following is a sample of what was offered at the 2015 meeting.3D Laser MappingData collection and data analysis are changing how mining is done. One field in which technological advancements have made safer and more efficient operations possible is through site and slope monitoring.3D Laser Mapping, a United Kingdom-based company, was on hand at the 2015 SME Annual Conference and Expo to display its solutions for the mining industry, including its SiteMonitor4D system.The state-of-the-art laser measurementbased system was developed in partnership with geotechnical engineers and mining surveyors, and is a simple-to-use, reliable solution that has the flexibility and performance to function in a range of monitoring applications.The system measures and monitors the stability of rock faces, landslips and man-made structures, including ongoing, periodic measurement of volumes - stockpiles, cutbacks and waste dumps and has high-speed laser scanning for regular mapping of large areas by mounting the scanner on a vehicle.With specifications that other monitoring techniques cannot achieve, laser scanning opens up a new dimension in mine measurement and monitoring.www.sitemonitorsystems.comA.R. Wilfley and Sons Inc.Founded in 1919, A.R. Wilfley and Sons Inc. has been manufacturing dynamic-seal and static-seal pumps in Colorado for nearly 100 years, delivering its high-reliability, low-maintenance, heavy-duty process pumps and slurry pumps to the global mining industry. The family-owned company is now in the hands of the fifth generation."We are the dynamic-seal experts," regional sales manager Cesar Murillo said. "Most other companies are unable to do 100 percent dynamic seals and have to use mechanical seals or packing," he said, but Wilfley’s sealing technology does away with the need for mechanical seals and packing and their associated problems. As a result, solids and slurry handling capabilities are high, the pump can be run dry, and product dilution is eliminated. The pump can tolerate more misalignment, more cavitation, and more vibration in the pump during operation."

Jan 1, 2014