Search Documents

By Vasilis Androulakis, Caroline Gerwig, Zach Agioutantis

Mining operations that involve caving of the overlying strata are designed so that caving occurs in a controlled manner by progressive overburden failure. However, there are many cases where the overlying strata bridge over the caved area for longer periods than anticipated and desired. As the caved area expands with the advance of the mining panel, excessive amounts of energy accumulate in the roof strata which will be rapidly released when the overburden eventually fails.

By Albert Ruiz

The 2,250-MW, coal-fired Navajo Generating Station located in Page, AZ draws water from Lake Powell using submersible pumps installed in five inclined shafts. Drought threatens to lower the reservoir to below the existing intakes. A system of new steel-lined intake shafts located on the same site was required for uninterrupted plant operation. The small size of the site, and the need to keep the existing system in operation, required detailed designs and placed significant limitations on construction equipment and activities. The Navajo Sandstone that forms the near vertical shoreline of the reservoir is 98 percent very fine grained quartz, highly abrasive and contains highly fractured intervals that presented numerous challenges to drilling the new 152-m (500-ft) deep, 109-cm (43-in.) diameter intake shafts inclined 23° to 26° from vertical. Spatial constraints, submersible pump design and operational criteria required that each shaft have a unique inclination and orientation and hit a small breakout target located 76 m (250 ft) under water. Sophisticated drilling equipment and techniques as well as state of the practice downhole survey technology and methods were used to make adjustments and maintain drilling accuracy with less than 1 percent deviation. Environmental requirements mandated water as the drilling fluid and grout was not allowed in to the lake under any circumstances. The shafts were videotaped and the breakout locations were examined using an underwater remotely operated vehicle (ROV) to verify shaft locations and rock conditions, and to guide placement of pneumatic packers to ensure grout did not transmit to the lake during the steel liner installation. In anticipation of the invasion of quagga mussels, the shaft design included an allowance for a chemical dosing system and a copper-rich alloy at the exposed portions of the steel liner.

Jan 1, 2011

By K. A. Foo

Minproc Resources Inc. is developing a tailings retreatment project in Bolivia at the Colquiri zinc-tin-silver mine, in the Bolivian Andes. Mining at Colquiri has been continuous since 1940 and COMIBOL, the Bolivian state mining company, has owned and operated the underground mine since 1964. There are 10 million tonnes of tailings at Colquiri containing 0.51% Sn, 4.21% Zn and 50 g/t Ag. Minproc plans to mine and concentrate the tailings at 1.15 million tonnes per year to produce feed for pyrometallurgical upgrading. The tailings are moderately complex, with cassiterite grain size ranging from 200 to 5 pm. The marmatite (ZnFeS) in the tailings is relatively easily recovered, with zinc recovery of 80% to a 40%-45% Zn concentrate. The major problem with the zinc metallurgy is that the marmatite is complexed with iron, which results in iron contents of 14%-17% Fe in concentrate. This makes the product very difficult to sell because of the low Zn:Fe ratio. Most zinc smelters require a Zn:Fe ratio of 6:1 or 7:1, whereas this concentrate has a 3:1 ratio. Concentrate sale terms are therefore unfavorable, and the high cost of transportation from Bolivia to the smelters is an additional burden.

Jan 1, 1992

By V. Svalbonas

When the Trelleborg Divisions of Boliden Allis and MPSI merged, a unique opportunity occurred for two independent mill fabricators to compare various design procedures and the research upon which they were based. This paper documents such a comparison in the structural design area. Several SAG mill analyses are compared using both Boliden Allis and MPSI methods. The differences and similarities are then utilized in a correlation of critical stress definitions and the acceptable design and inspection criteria.

Jan 1, 1992

By R. Riding

Degussa Corporation's peroxide-assisted leaching (PAL) process was evaluated in the batch concentrate leach circuit at Hecla Mining Company's Republic Unit. The product leached in this batch circuit is a high grade gold-silver sulfide (predominately pyrite) flotation concentrate. The primary objectives of the test program were to determine the effects of dilute hydrogen peroxide addition on leaching kinetics, sodium cyanide consumption and precious metals recovery. The results of the testing demonstrated that using dilute hydrogen peroxide produced the following benefits: - 1. Batch leach time requirements decreased by 80%. - 2. Sodium cyanide consumption in concentrate leach reduced by 55%, which translated to an overall plant reduction of 20%. - 3. In the concentrate leach process, gold recovery was increased by 1 to 2%. Because of the excellent metallurgical results achieved with the use of dilute hydrogen peroxide, as well as an economic incentive, PAL has become standard practice in the concentrate leach circuit operation. A complete description of the Republic PAL plant evaluation and performance is provided in this paper. In addition, process chemistry considerations in regard to the role of hydrogen peroxide are discussed.

Jan 1, 1992

By H. Sevim

The utilization of high sulfur Illinois coal by utility plants has been decreasing since the enactment of 1990 Clean Coal Air Act Amendment. Illinois coal producers can make their coal saleable by offering the choice of taking the combustion by-products from the utility plants and placing them in the abandoned sections of their mines. To be competitive, however, coal producers need to select an environmentally acceptable transportation-handling-placement system through which the cost-per-ton of by-product disposed can be minimized. In this paper, a few such systems are presented. The favorable operating range of each system is determined in terms of distance and tonnage. A case study is given whereby cost analysis is conducted for an underground coal mine receiving by-products from two Illinois utility plants.

Jan 1, 1997

By Ronald D. Hill

The occurrence of acid mine Drainage (AMD) with coal mining has been well documented. (1) Less documentation is available of its association with other types of mining, e.g., copper, gold, zinc, and sulfur. Yet there are many locations in the western states where acid mine drainage is as great a pollution problem as in Appalachia and in some cases, because of the high copper, zinc, and arsenic concentrations, they present an even more difficult problem. Until a few years ago, it was generally believed that the neutralization of acid mine drainage was uneconomical thus, AMD was allowed to discharge freely into our streams. However, the demand for good water finally dictated that the mining industry be included under pollution laws. In 1964 the Commonwealth of Pennsylvania passed a law requiring that all active mine discharges meet a discharge standard of pH 6-9, iron less than 7 mg/1, and the water must have a net alkalinity. Several other states now require active mines to treat AMD. In all but a few cases, lime neutralization, often in conjunction with aeration, has been the treatment method used. The high cost of lime as compared to limestone and the poor quality sludge, (slow settling, large volumes, and low solids content) has stimulated work in the utilization of limestone. This paper reports on the current state-of-the-art of limestone treatment of AMD.

Jan 1, 1970

By R. M. LaDouceur, C. A. Young, W. Nicholas

"Salicyl hydroxamic acid (SHA) adsorption on two rare earth oxides, lanthanum and yttrium, was studied. Adsorption at both surfaces occurred in two stages. Initially, the monovalent anionic collector appears to adsorb significantly and instantaneously in stage one and then becomes sluggish in stage two presumably because the initial stage passivated the surface. By comparison, adsorption during the sluggish second stage with lanthanum oxide did not stop but with yttrium oxide essentially stopped. Surface monolayer formation could not be observed in either of the two cases. Both stages appear to be due to multilayer formation of a surface precipitate as proven by Raman Spectroscopy for lanthanum oxide but inferred for yttrium oxide. Unlike the use of octyl hydroxamate as stated in the literature, increasing temperatures do not increase adsorption such that flotation of rare earths with SHA may be performed at room temperature leading to improved recoveries as well as significant energy savings. INTRODUCTION Rare Earth Elements (REEs) are comprised of the 15 lanthanides along with scandium and yttrium. The REEs with lower atomic numbers are relatively more abundant and are categorized as light REEs. On the contrary, the REEs with high atomic numbers are less abundant and referred to as heavy REEs. They are not really “rare” and, in fact, some of them are quite abundant in the Earth’s crust; it’s just that they “rarely” exist in concentrated deposits but rather are found dilute and practically everywhere. REEs share very similar physico-chemical properties but, because many of these properties are unique, they have gained enormous importance in recent times making several critical and strategic pending their use. For example, REEs have found extensive application in phosphor coatings, magnetics, and automobile cracking catalysts. Early technology was not advanced enough to produce commodity level production of the REEs and can be attributed to REE-bearing ores containing many rare earth minerals (REMs), not just one. In this regard, there are numerous REMs but bastnaesite, xenotime and monazite are considered to be the most common. Bastnaesite is a fluorocarbonate whereas the other two are phosphates. The separation of the individual REE-bearing minerals from the ores is not an easy task since they also exhibit very similar properties. Consequently, when flotation is used, it is done to produce bulk REM concentrates. For REM flotation, it is well established that octyl hydroxamate is more selective than fatty acid collectors (Pradip and Fuerstenau, 1983 and 1991). Liu et al. (2006) indicated that hydroxamates are the most common collectors for REMs. Pavez et al. (1996) studied the adsorption of oleic fatty acid and octyl hydroxamate on REM surfaces. Cui et al. (2012) studied the interaction of octyl hydroxamate with various REMs surfaces using various spectroscopic techniques such as XPS, FT-IR and Raman along with electron microscopy and concluded that such techniques offer ample information to establish adsorption mechanisms. Ren et al. (1997) studied napthalenic hydroxamic acid as a unique collector for flotation of REMs from bastnaesite ore and indicated that more selective collectors were needed. From these studies, it is clear that the quest of more selective collectors is essential but understanding how they adsorb at mineral surfaces is prerequisite to improving flotation performance."

Jan 1, 2016

By M. Laliberte

Gold mine effluents are often characterized by a high concentration of copper, ammonia and cyanide derivatives (mostly cyanates and thiocyanates). While non-acutely toxic to birds, this water can be acutely toxic to fishes and invertebrates. In many jurisdictions, the effluent requires further treatment in order to pass a mandatory requirement to be non-lethal to species like the rainbow trout (Oncorhynchus mykiss) or Daphnia magna. Using actual mine water, it has been demonstrated that aerated moving bed biofilm reactors will biodegrade the ammonia, cyanides, cyanates and thiocyanates, thereby removing the toxicity associated with these components. By removing copper by precipitation the water can be made to pass acute toxicity tests. Tests have demonstrated that the process is stable between 4 and 25 C, with no significant changes in the treated water composition. Once the biomass is acclimatized, the process is resistant to upsets and requires very little inputs except for phosphorus and air. Furthermore, it has been demonstrated that an anoxic reactor can be added downstream of the aerated reactors to remove nitrates if required.

Feb 23, 2014

"The Ohio River Bridge East End Crossing Tunnel requires a 75-year service life of its cast-in-place reinforced concrete lining. This twin-tube 3-lane (each tube) highway tunnel is about 55-ft wide and 30-ft high. Since unified tunnel service life prediction methodology does not exist in the US, challenges occurred during the design-build phase of this project. These challenges include the methodologies in determining the reinforced concrete’s degradation mode, the lining’s surface chloride concentration level, the reinforcing steel’s critical chloride threshold value for corrosion, how to verify the concrete’s diffusion coefficient, and the durability impact from concrete crack width. This paper presents a methodology in verifying the proposed concrete mix can achieve the service life requirements. This methodology can be adopted for service life prediction for future tunnels to be built in the US. INTRODUCTION The Ohio River Bridge East End Crossing (ORBEE) Tunnel is part of a Public Private Partnership project, which connects transportation network between Louisville, Kentucky and southern Indiana. Located in Louisville, Kentucky, the twin-tube highway tunnel provides northbound and southbound lanes of the Kentucky approach to a new bridge across the Ohio River. Tunnel lengths are approximately 1,675-ft and 1,685 for the northbound tube and the southbound tube, respectively. Connected by two cross-passages, both tubes have a roadway width of 40-ft, for 3-lane traffic, and a vertical clearance of 26.5-ft.The tunnel was constructed by drill and blast method with shotcrete and rock dowels as initial ground supports. The final tunnel lining system includes: •,Nominal 16” cast-in-place reinforced concrete lining, with 2” and 3” concrete covers over reinforcing steel for its extrados and intrados, respectively. •,20” cast-in-place reinforced concrete invert slab, with 4” and 3” concrete covers over reinforcing steel on its top face and bottom face, respectively. •,PVC waterproofing system around tunnel perimeter, excluding invert slab. •,Perforated PVC groundwater collection pipes on both sides of the tubes and one below the invert slab of each tube."

Jan 1, 2016

By D. A. Norrgran

The term "secondary recovery" has recently brought on a new meaning in view of the depletion of natural resources, energy conservation, plant optimization, and the environmental consciousness that has led to hazardous waste management, recycling, and secondary processing. Many secondary recovery processes are being developed applying mineral processing technology. Gravity separation, magnetic separation, and flotation have all emerged as implicit methods for recovering residual values from various process streams and hazardous constituents from waste streams. Recently, a technique for concentrating metallics has been successfully reintroduced. Although the concept of the eddy-current separator was developed over a century ago, (Patent 400317 issued to Thomas Edison on March 26, 1889) it was not until this last decade that it gained prominent acceptance. The evolution of permanent magnets has provided a cost effective alternative for the generation of high intensity magnetic fields. High energy permanent magnets have substantially reduced the capital and operating costs over the electromagnetic circuits employed in antecedent eddy-current separators. Specifically, in recent years, the strength of permanent magnets has increased several fold with neodymiun-boron-iron rare earth magnets now providing an energy product of 35 million gauss-oersted. Figure 1 shows the evolution in the strength of permanent magnets. The development of these rare earth magnets has led to the design of circuits possessing a magnetic force an order of magnitude greater than that of conventional permanent magnetic circuits.

Jan 1, 1991

By H. C. Harrell

The Tennessee Valley Authority began employing geophysical well logging for foundation investigations in October 1973. Since that time more than 3,000 holes have been evaluated for engineering purposes. The Tennessee Valley Authority has not actively used geo-physical well logging for exploration of construction materials, but we feel that much of the information derived from geophysical logs for foundation exploration is applicable to the construction materials industry. This paper will then discuss geophysical logging as applied to foundation engineering and, by implication, the feasibility of use in construction materials exploration. The use of geophysical logging and percussion drilling instead of coring has greatly expanded TVA's data acquisition capabilities and has also resulted in substantial savings in time and money. Economical boreholes are obtained through the use of large percussion track drills (Figure 1). This equipment is capable of drilling through the overburden, setting steel casing on the top of rock, and drilling the rock beneath the casing. Holes as deep as 400 feet (121.9 m) have been drilled by this method.

Jan 1, 1977

By Reinhard Gertl, Soroush Dabiri, Juan-Carlos de Rueda

The Tunnel of Guillermo Gaviria Echeverri, spanning 6.05 miles, will be Latin America’s longest road tunnel, is currently under construction in Colombia’s Antioquia Department with a single bidirectional tube connected to a parallel rescue tube through multiple cross-passages. The study faces challenges in implementing the prescriptive semitransversal ventilation system due to design restrictions. Different ventilation concepts are eplored to nd the most suitable system for regular operation and re scenarios. A quantitative ris assessment evaluates each alternative system and identies the longitudinal ventilation system, accompanied by ris mitigation measures, as the safest choice, since it surpasses the prescribed semitransversal ventilation concept.

Jun 23, 2024

By Paul Cameron Gilmour

Geologically, as distinct from economically, "porphyry copper (molybdenum, gold, silver, etc.) deposits" might be defined as large, disseminated and/or stock-work occurrences of copper-minerals, generally averaging less than 1 per cent cop-per. They are normally associated with small plutons which range in composition from granite to diorite, although, typically, they consist of quartz monzonite or granodiorite. Circumstantial evidence indicates that these "minor" granitic intrusions may represent the intrusive phases of post-orogenic, calc-alkaline volcanism, this conclusion being suggested by: 1. Texture and grain size. 2. Prevalence of intrusive breccias. 3. Relationship to unconformities and estimated depth of emplacement. 4. Spatial distribution in relation to orogenic zones. 5. Age of mineralization and igneous episodes

Jan 1, 1972

By Loic Galisson

"Urban tunneling projects are usually extensively monitored. Most of the instruments used rely on benchmarks providing a sustainable datum throughout the life of the project. The monitoring program also is based on a predicted model of deformation induced by specific construction methods. Events can interfere with those assumptions and eventually alter the stability of these datum. In addition, the anticipated ground conditions and hence the theoretical deformation model often differ from reality. Satellite Radar Interferometry provides useful information to overcome the weakness of the hypothesis made before construction. It is also a powerful tool to ensure the continuity of the monitoring program throughout the life of the project, accurately describing the true effect of the project on the surrounding environment. This paper emphasizes the benefits and limitations of this technique for urban tunneling applications, illustrated by examples of major tunneling projects around the world. MONITORING URBAN TUNNEL PROJECTS Why Monitoring? Retrofitting existing tunnels or constructing new tunnels – including access and retrieval shafts, portals and cross passages – implies an alteration of the neighboring soil structure. Excavating, dewatering, grouting, loading tie backs, etc. artificially modifies the natural equilibrium of the pore-water pressure, of the water table level and of soil stability. In many cases, the effects are immediate: ground loss, deformation of utilities, settlements of buildings, and distortion of infrastructure are a few examples resulting from construction activity.Instrumentation and Monitoring Scope To control and mitigate the risks of damage associated with the above effects, tunnel projects usually include an instrumentation and monitoring program. Depending on the level of geotechnical, structural and environmental risk, the magnitude of this program varies. Projects with a low exposure to risk may restrain the program to conventional methods such as limited topographical surveys and intermittent manual readings of geotechnical instruments. On the other hand, iconic projects with high risk or with controversial history may implement complex and extensive instrumentation plans, involving highly technical solutions such as Automated Motorized Total Stations (AMTS – see opposite Picture 1), Multi-Point Borehole Extensometers (MPBX), In-Place Inclinometers (IPI) and a wide series of fully automated geotechnical, structural and environmental sensors. In this case, all the devices are usually connected to field data loggers collecting raw data around the clock at frequencies ranging from days to seconds, depending on the sensors."

Jan 1, 2016

By Tim Langmaid, Steve Skelhorn, Stephanie Robillard, Allen Mitchell

"The Port Mann Main Water Supply Tunnel project provides a critical water main crossing of the Fraser River for the owner, Greater Vancouver Water District (Metro Vancouver). The project consists of two 60-metre-deep slurry panel shafts and a 1-kilometre-long, 3.5-metre excavated diameter tunnel located near Vancouver, British Columbia, Canada. The initial tunnel lining is a precast concrete steel fiber reinforced gasketed segmental lining. The final lining is a 2.1-metre-diameter welded steel pipe. This paper describes the challenges encountered during tunnel construction and the solutions implemented. Key challenges include earth pressure balance tunnelling at up to 6 bar pressure—the highest to date in Canada—a water-crossing without surface access for the majority of the tunnel drive, ground freezing from a river platform for a critical TBM intervention, and boring through cobbles and boulders in dense glacial till. INTRODUCTION Metro Vancouver supplies drinking water to 18 municipalities, one electoral district and one treaty first nation, serving a population of more than 2.4 million residents. Water is collected in three mountainous watersheds to the north of the Greater Vancouver area, in southwestern British Columbia, Canada. To supply the growing demands of Metro Vancouver’s customers, treated water must be conveyed across two significant water bodies: the Burrard Inlet and the Fraser River. The existing Port Mann water main is one of several key links between the watersheds north of Vancouver and the municipalities south of the Fraser River. The Port Mann Main Water Supply Tunnel (PMMWST) is the first of a series of upgrades, to increase capacity, enhance scour protection, and improve seismic resilience. The new tunnel is 3.5 metres (11.5 ft) in diameter and 1 kilometre (0.6 mi) long. When completed, it will contain a new 2.1 metre (7 ft) diameter steel water main that will help ensure the continued, reliable delivery of drinking water to these municipalities, and will more than double the capacity of the existing 1.2 metre diameter main."

Jan 1, 2016

By E. De Souza

Rockbursts and rockfalls cause very large safety and productivity losses in underground mines. One of the major unsolved problems of safe, economical rock support in underground mining has been that of maintaining anchorage during dynamic rock loading conditions or seismic related occurrences. It is recognized that the large displacements and high strain rates in excavation walls and underground structures cannot be countered by increasing the strength of stiff rock-reinforcing systems but must be accommodated by introducing yieldability into the support elements. This paper introduces a low cost yieldable support system which provides viable solutions to dynamic support loading. Such system should not only provide a feasible and more effective rock mass stabilization strategy but improve mine safety and reduce losses.

Jan 1, 1998

By Allan G. Provost

Shaft construction is assuming ever increasing importance when new mining enterprises are considered. The reasons for this increased emphasis is the much greater depths at which many new ore-bodies are being developed and the rapid depletion of near surface reserves requiring mines to go to greater depths on existing deposits. These greater depths increase the probability of exposure to unfavorable geologic conditions and it is more likely that high ground and/or water pressures will be experienced at these depths. The large capital costs involved and the critical position of a shaft in the overall mining program necessitate that this element of project development be given careful and critical consideration. The Henderson No. 2 Shaft is located in the Rocky Mountains of north central Colorado (See Figure I), about 55 miles west of Denver, near the community of Empire in Clear Creek County. At the 10, 442 foot collar elevation, winter arrives in late September and brings snow to contend with until May. The labor force for Shaft No. 2 is approximately 90 men. They are provided access to the project via all-weather U. S. Highway 40. SHAFT DESIGN The Henderson No. 2 Shaft is a 28-foot I. D. circular, concrete lined (1 foot thick) vertical shaft. The final depth will be approximately 3100 feet

Jan 1, 1972

By J. A. Lombardi

Innovative hard rock narrow-vein, longwall, and stope leach mining systems concepts are described and evaluated economically. The principal tool proposed for use in these systems for both mine development and production is the U.S. Bureau of Mines radial-axial splitter. The mining systems concepts are prefeasibility level costed and projected to be cost competitive for steeply dipping veins, 0.6-1.2 m wide, for horizontal tabular ores 2 m -5 m thick, and for leachable ores with greater than a 1.7:1 stripping ratio. In all of the systems the orebody, less swell, is retained underground for use as backfill.

Jan 1, 1994

By B. Y. Wong

In April 1989, Southern Company Services signed a 3.5 year contract with DOE-PETC for generic engineering development of an advanced physical fine coal cleaning technology known as selective agglomeration. This technology offers the potential for significantly higher pyritic sulfur removal (90% +) than conventional coal cleaning (30 to 50%) while maintaining high Btu recovery (90% +). Engineering development will include bench-scale process development; component development; adaption or modification of existing unit operations; proof-of-concept (POC) module design, fabrication, testing and evaluation; and small commercial facility conceptual design. The information obtained during POC operation will be sufficient to result in a technical and economic design base that can support construction and operation of a small commercial plant. The major goal of the research is to develop selective agglomeration technology to achieve 90% pyritic sulfur removal while operating at Btu recoveries above 90% based on run-of-mine quality coal. This objective will be accomplished in two phases: Phase 1 -bench-scale and component development, and Phase 2 -POC module operation and conceptual design of a small commercial plant. Currently, work is proceeding under Phase 1 (Tasks 1-7) of the project. A review of the status of Tasks 1-7 is presented in this paper.

Jan 1, 1991