Search Documents

Mining steeply dipping coal seams is a difficult task. Prior to 1996, fully mechanized longwall mining methods along the seam strike direction were tried in China and other countries. Due to its larger coal reserve in steep seams, China made more, but still limited, progress on mining such seams than other major coal-mining countries. In the last two decades, accelerated research efforts have tried to improve the mining technology in steeply dipping coal seams. Based on this work, a dynamic model of a roof-support-floor (R-S-F) system under asymmetrical constraints in mining steep seams is established here, and a theory of strata control and hazard prevention is formed. The key technologies for mining steep coal seams include global and regional strata control methods in the longwall face; methods for the longwall face machines to sustain static and dynamic loads; and flexible protection technology. These theories and technologies have been successfully applied in China to the mining of steep coal seams of varying thickness and hardness, with hard and soft roof and floor, and with a high potential for spontaneous combustion. In recent years, the technology has been introduced to Russia, India, Uzbekistan and other countries where steep coal seams are mined.

Jan 1, 2013

By Raymond E. Kary, John W. Mcklveen

The four unit Cholla coal fired power station at Joseph City, Arizona, consumes coal from the McKinley mine located in western New Mexico. Since coals may contain relatively high uranium or thorium concentrations and may release quantities of detrimental progeny of these elements to the environs, there is concern that releases may pose an adverse environmental impact or even a health hazard to the workers. Thus, an effort was made to quantify the radionuclide content of the coal and compare the results with radionuclide concentrations already present in the vicinity of the plant. Additionally an attempt was made to assess any potential for significant enhancement of the levels of radioactivity in the environment or to plant personnel. Background gamma radiation measurements at and near the plant ranged from 8 to 12 [µ]R/hr (70 to 105 mR/yr) with a few localized anomolies measuring to 18 [u]R/hr (160 mR/yr). Levels on top of the coal storage piles decreased to ~ 6.5 [u]R/hr (60 mR/yr). Apparently the direct radiation emitted from the coal is less than the background levels in the vicinity of the plant. Measurements performed on top of several coal seams at the mine confirmed low radiation levels emanating from coal, but readings more than doubled when the overburden was monitored. Laboratory gamma spectrometry confirmed the lower amounts of natural radioactivity in the coal when compared against soil and water samples obtained in the vicinity of the plant and the overburden at the mine. In an effort to see if there is biological enhancement, animal feces was sampled. The radiation variations were found to be influenced primarily by naturally occurring potassium-40 which varied from ~ 1 to 18 pCi/gm rather than fluctuations in the uranium and thorium series. The potassium-40 concentrated in the ash were similar to the concentrations in the environs around the disposal ponds while Radium-226 concentrated in the fly ash was ~ 3 times that found in the immediate surroundings. Radon-222 gas concentrations in buildings at or near the plant ranged from 0.5 to 1.8 pCi/l and were generally lower than indoor concentrations measured in the Phoenix area. The burning of coal at the Cholla station does not appear to increase ambient levels of radioactivity found in the surrounding environs or to the workers. However, the use of byproduct fly ash for construction purposes may need to be examined.

Jan 1, 1981

By Hubert E. Risser

At the outset of a discussion on the adaptability of Illinois coals for use in iron and steel production, it is perhaps well to define terms. ?Adaptability? as used in this context, means that a coal can be, adapted to use within a given technological and economic framework. For a coal to be adaptable, to use in the manufacture of metallurgical coke within the present technological and economic framework, it must possess, among other things, at least the following characteristics: 1. The coal must be capable of producing, alone or in combination with other coals, a coke that can meet at least a minimum standard of required performance in the present-day blast furnace. The coke must have sufficient strength, stability, hardness, and freedom from impurities to make it suitable. 2. If the coal in its raw form does not meet these requirements, it must be amenable to beneficiation or upgrading so that the requirements can be met. 3. It must be available in uniform quality and in sufficient quantities to meet the need. 4. Use of the coal must be economically attractive. If its quality is equivalent; to that of the coals with which it must compete, it must be no more expensive than they. If It is better, a premium price may perhaps be demanded. If, in any respect, it is the least bit less suitable, the cost must be lower to offset its disadvantages.

Jan 1, 1961

By QUANWEN PU, Yonggang Wei, Bo Li

With the advancement of industrial science and technology, more and more catalysts are used. The spent catalysts produced are solid waste products, which cause environmental pollution if they are not treated. At the same time, the spent catalysts contain some precious metals such as platinum in concentrations that are often higher than in their ore resources. Therefore, the recovery of valuable metals in spent catalysts is a hot research topic at present. However, due to the complex structure of the spent catalysts, dealing with them is a lengthy process. The first step of recovery, enrichment of the spent catalyst, becomes particularly important. In this paper, a pressure solution method is investigated for this purpose, in which the alumina carrier is dissolved and platinum is enriched in the leaching residue.

By Robert E. Moore

Investigators have attempted to develop lime refractories on a scale for broad applications in the metal and ceramic industries for several decades. There was a flurry of activity in the early to mid-fifties but no commercial developments were forthcoming. The literature of that period yields little information on plant trials. A major factor suppressing past interest in lime has to have been the high success with the application of magnesic and dolomitic materials. These materials, usually tar-bonded or impregnated, have become the refractories success story of the past two decades, especially in BOF applications. It is safe to say that their development and application has essentially plateaued, and that work today is focussed on finding cheaper paths to produce MgO-based refractories. For example there are efforts underway to extract MgO from mineral magnesite and to combine natural dolomite with MgO1. Beginning in the late sixties, rather intensive research began on the development of CaO brick, especially in East and West Germany, in Poland, and other communist bloc satellites, 'and also in Italy and Spain. One speculates that the motivation was a regional shortage of good magnesia and dolomitic material. Of course, There has always existed the prospect of cost savings should it be possible to use raw limestone as the starting material. Quite a large literature has appeared treating of these developments which in the early seventies had already reached full plant scale trials and uses. Some of the directions followed in the research have led to novel methods of brick manufacture.

Jan 1, 1985

By Raphael Mourad, Colin R. Phillips

Fluorescence, radioluminescence, phosphorescence and thermoluminescence in TLD 100 and 700 are discussed and compared. The energy budget in thermoluminescent material is presented in general terms. Results of measurements of radioluminescence, phosphorescence and thermoluminescence in LiF:Mg irradiated with [a] radiation, using simple facilities, are presented. The calculated energy budget in the exposed chips using [a] radiation is compared to published data using [y] irradiation.

Jan 1, 1981

By K. L. Wiley

In-situ leaching, initiated in 1986 at San manual, was economically developed in 1989. The primary reason for this lag time between startup and viable production was the time required for technical development. The technical development pursued comprised detailed design, development, and implementation of in-situ well construction methods, formulation of suitable well pattern arrays, and the development of extensive hydrogeologic and geochemical knowledge of the mineral deposit. Since 1989, the in-situ leaching program has become a viable and cost effective method to extract copper from the supergene mineralized zone of the San Manuel deposit. The in-situ leaching methods that are currently utilized have been progressively expanded and continually developed and will became the cornerstone of copper production from the San Manuel oxide mineral deposit. This paper presents an overview of the supergene hydrogeology, current design techniques, drilling methods and well completion, pump determination and setting, solution management, and future plans for the increased extraction of copper by in-situ leaching methods at the San Manuel mine.

Jan 1, 1993

By K. I. Cunningham, C. S. Spirakis

Two types of native sulfur deposits have been found in Lechuguilla Cave: thin late-stage crusts and massive early- formed deposits. Most, if not all, of the crusts appear to have formed by remobilization of native sulfur contained within gypsum and sulfur masses. The process is occurring today and is slowly converting the sulfur to gypsum. The absence of primary gypsum or reductants in the cave indicates that the early-formed massive sulfur deposits did not form by in-place reduction of sulfate, which is the process that formed the commercial sulfur deposits in the Delaware basin. Instead, it appears that H2S dissolved in basinal brines was oxidized by oxygen in near-surface ground waters in the cave. Fluid- inclusion data, which suggest the presence of both fresh water and saline water as the sulfur formed, support this interpretation. Although individual sulfur deposits in Lechuguilla Cave are no more than several tens of metric tons, the abundance of secondary gypsum (as much as 10 meters thick) indicates that native sulfur may once have been much more extensive.

Jan 1, 1992

By Sandip K. Mukherjee

This paper describes the application of pressure foam to control respirable dust in a double-drum longwall mining section. The feasibility of passing an adequate quantity of pressure foam through the shearer drum was initially established in the laboratory. Thereafter, underground testing of the foam system to determine its effectiveness on an active operating longwall was conducted in a mine in West Virginia. The foam system proved superior to the water spray system. The de- tails of the laboratory and field investigations, the results obtained, and the degree of acceptance of this system by the mining company are discussed in this paper.

Jan 1, 1984

By J. D. Miller

X-ray computed tomography (CT) techniques have been developed for the medical services field in order to provide accurate internal images of the human body.(l-7) Now, a decade later, CT techniques are starting to be used in non-medical applications such as, non-destructive testing(8), flow pattern analysis(9), drill core examination (10,11), and coal characterization(12,13). In these fields of application, CT techniques offer the potential to extend our knowledge and understanding beyond that provided by more traditional methods of analysis. Although, CT systems involve very specialized and expensive equipment, the advantage of x-ray CT in revealing the detailed internal structure of an opaque material non-destructively should make it an important tool to provide a more complete analysis of mineral processing phenomena. X-ray CT systems generally consist of an x-ray source/collimation unit and a detector/data acquisition unit. The object to be examined is placed between the two functional units as shown in Figure 1. With this system the density array of selected cross sections of a chosen opaque object can be obtained in two dimensions. There are numerous areas in mineral processing to which x-ray CT technology can be applied and it is the aim of this article to identify these potential areas noting the advantages and limitations of the technology. Particular emphasis is placed on particle composition distribution and multiphase fluid flow measurements. In the case of particle composition distribution, liberation analysis and coal washability are considered. While in the case of multiphase fluid flow, swirl flow in the air-sparged hydrocyclone is given by way of example.

Jan 1, 1989

By D. Koren, D. Carson

Disposal of smelter slag may be subjected to regulatory leach tests to deter- mine whether they produce a leachate containing contaminants in excess of stated limits. Contaminants that are most often of concern for smelter slags are As, Cd, Cr, Cu, Ni, Pb, and Zn. The present regulatory tests are based on the assumption of storage in a municipal landfill dump, where wastes are in contact with organic acids. Since slags are not normally stored in such an environment, these tests do not adequately assess the true leachability potential of the slags. Ten slags from six major Canadian nonferrous sulfide smelters were studied. Leaching was done following regulatory and modified tests, including leaching in columns with synthetic acid rain for a 25-week period. The slags were characterized by mineralogical analysis before and after leaching with synthetic rain. The synthetic mineral equivalents (hereafter referred simply as phases) in the slow cooled slags consist of fayalite grains and dendrites, amorphous glass, some spinel and small quantities of complex sulfidic prills and metallics. The phases in the quenched slags consist of amorphous glass, some spinel and small quantities of complex sulfidic prills and metallics. Some metal dissolution took place during leaching. However, for all leaching tests, the concentrations were always below the regulated limits. In general, the content of the potentially leachable elements remains unchanged in the fayalite, in the amorphous glass and in the spinel, whereas the quantity of sulfidic prill and metallics decreases after leaching. Therefore, most of the deleterious element dissolution comes from the sulfidic prills and metallic phases. Metal dissolution increases by crushing the slag, probably due to an increased exposure of the sulfidic prills to the leaching solutions.

Jan 1, 1998

By H. W. Gao

During the last decade, the feasibility of applying the in situ leaching technology to the recovery of copper from deeply buried deposits containing chalcopyrite has received much attention.(1-4) The major incentive for using this technology is that under certain circumstances, copper in deep underground deposits, which cannot be mined economically by conventional means, can be recovered economically. Basically, this technology involves rubblization of the deeply buried copper ore body followed by in-place leaching of the rubblized copper ores. Rubblization of the ore can be achieved by some suitable method such as the use of block caving mining. The rubblized chimney is then filled with water until the original water level is reached. Leaching occurs when the eater saturated with oxygen is introduced into the chimney- and flows through the fractured rock masses and within pores of rocks. As the dissolved oxygen oxidizes the primary sulfides, heat is generated. Because of low conductivity of the surrounding rocks, the generated heat is able to raise the temperature of the chimney. The increase in the temperature of the chimney and the relatively high content of dissolved oxygen in the leach solution under high hydrostatic pressure will result in an enhanced dissolution of the primary sulfide minerals. To ensure a successful application of the in situ leaching technology, a complete understanding of the effects of the ore particle size distribution, ore grade mineralogy, temperature, pressure, lixiviant concentration, pH, etc. on the rate of copper recovery is necessary so that copper can be recovered efficiently and the amount of copper extracted can be predicted. These can be achieved through mathematical modeling of the in situ leaching process and conducting laboratory tests. In this paper we will present a mathematical model that simulates the in situ leaching process as depicted in Figure 1. To model this process properly, not only the 'kinetic and thermodynamic aspects of leaching chemistry must be known, but the effects of heat generation, the physical aspect of fluid flow and other related multicomponent transport phenomena must be considered. Furthermore, since most factors involved in the leaching process change with time, a leaching system must be described using unsteady state equations.

Jan 1, 1981

By Apostolos Vrakas, Georgios Anagnostou

"INTRODUCTION The small strain assumption routinely made in tunnel analyses remains sufficient from an engineering point of view as long as convergences do not exceed 10%. More specifically, small strain theory assumes that deformations are so small (in relation to the size of the underground opening) that any geometric change in the continuum can be disregarded (Fig. 1a). In fact, however, the geometry is updated during loading (or unloading) according to large strain theory and thus equilibrium and stiffness are evaluated on the deformed configuration of the continuum (Fig. 1b).In problems involving large deformations, where the undeformed and the deformed tunnel geometry differ significantly, small strain theory leads to erroneous and sometimes even nonsensical results (i.e. it can predict wall displacements even greater than the excavated radius under conditions of very low stiffness and strength, high in situ stress and low support pressure). This can easily be verified from the widely applied relationships for the ground response curve. For example, in the ideal case of linearly elastic behaviour, the convergence of an unsupported opening equals (1+?) s0 / E (where E, ? and s0 denote the Young’s modulus, Poisson’s ratio and initial isotropic stress, respectively) and is greater than 100% for E < (1+?) s0. Although convergences are less than 10% in the great majority of tunnelling projects, very large deformations may take place when tunnelling through weak rocks under a high overburden (Fig. 2). This paper will first present a very simple and practicable way to account for large strains, based entirely on the results of routine small strain analyses, and will subsequently show the importance of addressing large strains in tunnel analysis and design with reference to three typical case studies of tunnelling in squeezing ground."

Jan 1, 2016

By R. K. Rajamani, R. Verma

In ball milling the rates of breakage vary primarily with the size distribution of powder in the mill. Using an approximate solution to the batch-grinding equation, the acceleration and deceleration of breakage rates of all individual size classes are determined when the grinding environment is varied. Experimental results with limestone and copper ore show time-dependent breakage rates under both dry and wet grinding conditions. The effect of grinding additives on breakage rates is also studied. In general, breakage rates increase for coarse sizes and decrease for fine sizes with an increase in the fines present in the mill. Such variations have strong implications in closed-circuit grinding.

Jan 1, 1992

By Jakub Nalaskowski, Robert Aranowski, Jan D. Miller, Jan Hupka

The polyolefins, mainly polyethylene and polypropylene particles, are used as an active filler material in polymer-polymer blends and are being used for the modification of asphalts to pro- vide for high-load, low-maintenance road construction. The stability of prepared blends depends on the interaction forces between polyolefinfiller and the matrix and/or between two polyolefin filler surfaces in the polymeric matrix. Various additives, especially surfactants, can be used to modify these interactions and improve the stability of polymer blends. In current research, direct force measurements between polyethylene (PE) surfaces in n-tetradecane, a nonaqueous solvent imitating the polymer matrix, were performed in the presence of lauric acid and dodecylamine using the AFM colloidal probe technique. Additionally, the zeta potential of polyethylene particles in the presence of surfactants in n-tetradecane was measured. The interac- tion forces between the polyethylene surfaces can be described as a combination of electrical double layer repulsion and steric repulsion between polymer chains extending into the n-tetradecane sol- vent. The addition of surfactant to the n-tetradecane was found to increase the repulsive force between the PE surfaces. The strongest repulsion was observed for dodecylamine. Additionally, the temperature efect on the interactions in n-tetradecane was studied. It was found that steric repulsion between the PE surfaces increases with an increase in temperature.

Jan 1, 2003

By J. D. Miller, Jon J. Kellar

Researchers in flotation chemistry have long sought to describe collector adsorption phenomena in greater detail including kinetics, orientation and interactions between adsorbed species. Now a quantitative description can be made in-situ using FTIR internal reflection spectroscopy. Details of the adsorption process at the surface of mineral crystals, machined into internal reflection elements, can be described from first principles, provided the refractive indices, incident angle, and wavelength of light are known. Collector orientation can be established based on spectral characteristics of plane polarized and perpendicular polarized light. Examples of the use of in-situ FTIR internal reflection spectroscopy are given for the sapphire-sodium dodecyl sulfate system and for the fluorite-sodium oleate system. It is expected that quantitative in-situ analysis of collector adsorption reactions by FTIR internal reflection spectro-scopy will continue to grow in importance and will provide an important new dimension in our understanding of flotation chemistry.

Jan 1, 1989

Introduction The objective of the design and operation of a mine is to make as much money as possible within certain reasonable and responsible constraints. The imposition of constraints on the objective of maximizing profits can result in an optimum mine design. This paper deals with the maximization of profits. Optimization will be discussed in a future paper. In the mining industry, it is generally accepted that the maximum economic recovery is defined by identifying the reserves and the sequence of mining that results in maximum net present value (NPV) or discounted cash flow-rate of return (DCF-ROR), as indicated in Fig. 1 (see Lemieux, 2000). Current parametric analyses techniques, such as varying the mining costs; profit reservation; sales price or metal content, to define pit limits and mining sequence technically referred to single, double or triple parameterization, do not assure that the curve in Fig. 1 will be maximized. In defining the sequence, the first material to be mined should be the first grouping of recoverable mineral that has the highest after-tax unit value and that forms a feasible mining unit. The assumed mining of the first pit should be followed by the assumed mining of the second most profitable and practical pit or pit expansion. If this process of grouping and sequencing is followed until the profitability approaches zero, the general sequence required to extract the maximum economically recoverable reserve is identified. The curve in Fig. I is constructed by calculating the NPV for a series of sequences, each assuming operations are terminated on successively lower profit pits. If the operation ceases on a pit with too high of a profit, opportunity is lost, and the NPV is lower than the maximum. The NPV curve peaks and then starts to decline before the zero-profit pit is assumed mined. This occurs because the money invested in advanced stripping would have produced a greater return if it was invested at the dis¬count rate. The maximum economically recoverable reserve is defined by the pit limit corresponding to the maximum NPV or DCF-ROR. Pit and phase definition The real challenge of reserve definition is identifying the phasing and after-tax profit per ton, so that the curve in Fig. 1 can be plotted. The after-tax profit cannot be properly addressed until after the pits are designed, the production is scheduled and the cash flow is estimated. Throughout the years, many investigators have ad¬dressed this problem. A major thrust of the famous paper in which Lerchs and Grossman (1965) presented their algorithm was to identify a sequence that would produce a result similar to that identified in Fig. 1. Whittle&apos;s (1988) four-dimensional analysis is designed to address this issue. The author addressed this same issue in a paper presented to the 1968 Canadian Institute of Mining national convention (Lemieux, 1968). Without a relatively simple methodology to con¬struct the curve in Fig. 1, the number of iterations in a trial-and-error method becomes prohibitively burden-some. The pit designer seeks a simple pit-planning parameter that will serve as a proxy for the after-tax profit per ton used in defining the curve in Fig. 1. The designer&apos;s goal is to apply this pit-planning parameter using standard pit-wall location techniques to design a series of pits that will provide a guide to the sequencing. Common techniques used to position pit walls are strip-ratio limits, highwall incremental analysis, floating-cone methods or "maximizer" applications1. Costs, revenues, noncash charges, taxes and profits are usually structured on a unit basis for use in the pit-wall location analysis. Application of the proxy parameter using the pit-design tools should, ideally, result in the definition of pits and sequences that will maximize the curve in Fig. 1. 1 The pit-design tool frequently referred to in the literature as an "optimizer" defines a pit boundary that maximizes the value contained within based on the input parameters and the safe pit-wall angle. The optimization of the pit design involves selection of rate of production, cutoff grade, product quality and other considerations. These considerations constrain the maximization of value. Therefore, pit-design tools that maximize value should be called "maximizers."

Jan 1, 2000

By L. Yuan

In the U.S. coal mining industry, most spontaneous combustion fires occur in longwall or worked-out gob areas. In order to reduce the fire hazard caused by spontaneous combustion, it is important to understand how ventilation and gob characteristics affect the spontaneous heating process. Given the difficulty to conduct field tests in such an environment, a computational fluid dynamics (CFD) study was conducted to investigate the effects of ventilation and gob characteristics on the spontaneous heating process in longwall gob areas. Two longwall panels with a bleeder ventilation system were simulated. The spontaneous heating is modeled as the low-temperature oxidation of coal in the gob using the Arrhenius rate law and kinetic data obtained from previous laboratory-scale studies. The heat generated from the spontaneous heating is transported by convection and conduction, and oxygen and the oxidation products are transported by convection and diffusion. Unsteady state simulations were conducted with different ventilation conditions and gob permeability distributions. The ventilation parameters varied in the simulations are the pressure at the bottom of the bleeder shaft and regulator resistance in the second entry inby the longwall face.

Jan 1, 2009

By R. Mathur

Cu isotope fractionation in low-temperature aqueous environments has been well documented. Here Cu fractionation was applied to two distinct, yet related, mining problems. First, an exploration geology application, where copper isotope fractionation was measured in oxidized leach caps, chalcocite enrichment blankets and hypogene mineralization in three porphyry copper deposits located in the southwestern U.S. Cu isotope patterns exist in a vertical distribution within the mines, coupled with distinct relationships with the Cu grade. Second, a hydrometallurgical application, where copper isotope fractionation was measured in leach fluids, feed and residues from a quick leach test (QLT) on Cañariaco, Peru ores. The results indicate the relative proportions of the minerals providing Cu during leaching. Interpretations of the QLT test measurements indicate covellite is the dominant ore mineral providing Cu during leaching. Both applications clearly demonstrate the use of the Cu isotope technique to understand low-temperature aqueous processes involving copper.

Jan 1, 2012

By Ireneusz Tomza, Jolanta Lebecka

INTRODUCTION Radioactive deposits were observed in 1972 in some of the Upper Silesian coal mines. They were located mainly in the drains in galeries and on the inside surfaces of water pipes. They also caused some problems by accumulating in water pumps. It has been postulated that the deposits are produced by natural radioactive waters seeping from the rocks. Investigations were initiated to answer the following questions: - What is the composition and the amount of radioactivity in the deposits? - What radioisotopes are present in the water? - How are the radioactive deposits formed? - Do the radioactive waters also occur in other mines? - How does the radioactivity of the water depend on chemical composition? - What is the origin of the radioactive water? - Does the water and the deposits cause radiation hazards for miners? -How can the radiation hazard be reduced? METHODS OF MEASUREMENT Determination of Radium Isotopes in Water The commonly used methods of radium determination in water are either based on measurements of the radioactivity of 222Rn which is in equilibrium with 226Ra, or on the detection of alpha particles of the radium radioisotopes after chemical separation of radium from the water sample. The method based on radon activity measurements is very sensitive and does not require any chemical Separation, but it can be used for determination of 226Ra from the uranium series only, because the thorium daughter 220Rn has too short a half-life (55s to yield the required accuracy. The method developed by Goldin, 1961 [2] involved alpha-particle measurements in thin layers of RaS04 and BaS04 separated from the water. This method is not convenient for saline water and water with high barium concentration because the amount of barium carrier in this case is too large to obtain a thin layer of precipitate with sufficient activity. The Upper Silesian carboniferous waters are often saline with high barium content, so the method described by Goldin was not convenient for this case and it was necessary to change the detection system and modify the chemical preparation. The procedure developed by the authors for the determination of radium isotopes in water was as follows: - Depending on the Ba2+ content and the required sensitivity of measurement, a water sample of 200 cm3 to 3 dm3 was taken. - 10 cm3 of 0.25 M citric acid and 5 cm3 15M ammonia was added to form complex Ba2+ ions and avoid the immediate precipitation of BaSO4. (This was repeated as long as the addition of BaC12 did not form a precipitate.) - 1 cm3 of 1N solution of Pb(N03)2 as a carrier for radioactive isotopes of lead and 10 cm3 of 0.1 N BaC12 as a carrier for radium were added. - The sample was heated to the boiling point and the precipitation of RaS04, BaSO4 and PbS04 with 50% H2SO4 was carried out. - After several hours the sample was centrifuged and the precipitate was purified by washing with nitric acid and distilled water. - The precipitate was then redisolved in 20 cm3 0.125 M Na2EDTA and 3 cm3 6M ammonia and reprecipitated from the solution by dropwise addition of acetic acid to d pH of 4.5. At this value of pH, precipitation occurs only for the barium and radium sulfates, while lead and all other radioactive elements remain in the solution. The date and time of deposit precipitation was recorded. - The final barium-radium sulfate mixture was washed with distilled water and transferred to standard measurement vials. - Each vial containing a deposit had 6 cm3 of distilled water added and was then shaken vigorously. 12 cm3 of liquid gelling scintillator (INSTA-GEL UNISOLV-1 type) was then added and the vi 1 was shaken again. After a while the scintillator turns into a milky gel in which the deposit is uniformly distributed. - The standard sample of 226Ra was prepared in the same way. - The activity of the samples was measured using a liquid scintillation spectrometer. (In this case the TRICARB 3320 produced by Packard Instruments, was used). Tests run on standard radium solutions provided by Amersham Radiochemical Centre indicated that this method of measurement enables one to achieve an efficiency of almost 100% (within measurement error). For alpha particles no quenching effect was observed for the BaS04 concentration in the range up to 80 mg of BaS04 per 1 cm3 of liquid scintillator coctail (Fig. 1). This provides a sensitive determination of radium in water with high barium content and also in saline water. In saline water the solubility of barium sulfate is much higher than in

Jan 1, 1981