Search Documents

By Fred D. Wright

In this paper the principal theories used to design roof bolting systems are presented and discussed. Then the characteristics of various types of roof bolts are presented and finally the interaction between rock and roof bolt characteristics on choice of roof bolts is discussed. Theories can be considered design tools which may or may not be appropriate for a specific situation. It is good for a design engineer to have a number of such tools available and also important that he understand their good features as well as their limitations. Hence, some of the principal theories and classification systems used for design of roof bolting systems are discussed first.

Jan 1, 1982

By A. Maréchal

It has been shown since a few years that the problem of estimating recoverable reserves should be solved by using specialized statistical techniques : whenever the selected blocks are chosen without any other constraint than a cut-off grade criterion, the problem of estimating the corresponding tonnage-grade curve is resolved by estimating the local histogram of block grades. Two major statistical techniques are currently used by geostatisticians to estimate local histograms : the "average conditional distribution" technique (Parker, Journel, Dixon 1979) and the disjunctive kriging technique. (Matheron, 1976, Jackson, Maréchal, 1979). Both have proved to be applicable in practice, with their pros and conconcerning their practibility and versatility.

Jan 1, 1982

By J. C. Ransdell

A conventional paddle-type mixer and a gravity-flow mixing device were evaluated for conditioning of fine phosphate feed (- 35 + 150 mesh) with fatty acid and fuel oil, and for acid scrubbing prior to cationic flotation. Gravity-flow mixing re- quired less residence time but slightly higher reagent concentrations to achieve recovery levels similar to conventional conditioning. Grade was less sensitive to reagent concentration using the gravity-flow mixer. For acid scrubbing, the gravity-flow mixer proved equally effective. In this paper, the effect of time, pulp density, reagent concentration, and emulsification on conditioning and acid scrubbing efficiency of the two devices is discussed.

Jan 1, 1987

By Steven G. Grannes

The Bureau of Mines, U.S. Department of the Interior, has developed a computer image processing algorithm to determine the size distribution of moving taconite (iron ore) pellets. This algorithm interprets line-scan images to measure pellet diameters. Pellet edge detection with a peak light intensity constraint is the basis of this technique. Preliminary error analysis indicates a normally distributed experimental error with a standard deviation of 0.09 and 0.15 for pellet diameters of 0.4 and 0.9 cm, respectively. System accuracy was independent of moving pellet speed below 50 cm/sec. Computer image-based size distributions were found to be in close agreement with standard sieve analysis.

Jan 1, 1986

By W. Robert Rose, Randall Pyper, Carlos Mirabal, Jaime Eguivar

In 1984, work was started to determine the viability of heap leaching silver-containing waste dumps from Cerro Rico near Potosi - Bolivia, at an elevation of 4300 meters (14 100 it.). The result today is an unusual heap leach utilizing fine crushing, grinding, and agglomeration to process 1000 tonnes per day of ore containing 200 g/tonne silver. The unique metallurgical, economic, and political factors will be discussed which led to the decision to build a heap leach rather than a conventional agitation leach plant. Capital and operating costs will be given along with some of the uncommon process design and equipment problems encountered while developing the operation.

Jan 1, 1990

By B. W. Cavender

Innovative mining and metallurgical operating techniques and processes can be identified and developed by analyzing changes as they occurs within the mine, plant, technology or industry. Sources of change to be monitored for innovative opportunities include unexpected successes or failures, incongruities between perceived and actual events, process needs, changes in perceptions and the development of new knowledge. Innovation can be organized, practiced and managed. The perception of change as an opportunity rather than a threat is mandatory, as is the systematic measurement of innovative performance. Innovation is enhanced by specifically designed policies regarding organizational structure and staffing, daily management practices and compensation and incentives.

Jan 1, 1996

By George W. Toth

This chapter describes the development of a computer code which rapidly estimates the cost of producing coal from either surface or underground mining situations. The computer code, termed the coal production cost (CPC) code, was developed under an NUS corporate research grant and was based on the findings of several coal mining and cost research analyses performed by NUS over a three-year period. The studies which served as the primary basis for the CPC code were the coal mining cost models developed by NUS for the Electric Power Research Institute. These models were designed for use in manual analyses and have been published by EPRI (Toth, 1977; and Stinnett, 1977).

Jan 1, 1979

By D. E. Ranta, Neil D. O’Donnell, Thad B. Ostrowski

Ore reserve estimation at the Syncrude Canada Ltd. open-pit oil sands mine in Northern Alberta has evolved since the project's inception. Early techniques followed a conventional petroleum reservoir analysis format, with relatively widely spaced drill holes and semiquantitative grade data. Experience has developed a more standard mining approach, including classification of geological materials by both lithology and sedimentary origin, timely and multi-purpose drill holes, precise analytical data, empirical recovery factors, a computerized geological data base, and an orebody block model. Future efforts will involve enhancement of existing techniques, use of geostatistical algorithms, quantification of confidence limits, and improved control of the ore model by geological parameters.

Jan 1, 1992

By J. G. Groppo, J. G. Justice, B. K. Parekh

Removal of particulates and/or metal ions from mineral/coal processing waste water is a necessity from the environmental point of view. This paper describes application of a novel AC- electrocoagulation technique to remove the particulates as well as metal ions using AC power. A series of laboratory tests conducted on a stable black water sample obtained from a sub-bitminous coal operation provided a clear supernatant (-10 NTU) from the suspension. The process also shows promise in removal of up to 90 percent of phosphate ions and other metal ions (copper and nickel) from solution. A preliminary economic evaluation of the process will also be included.

Jan 1, 1992

By O. A. Paulson, D. D. Runnells, D. P. Dupon, K. J. Bruxvoort

Background groundwater quality is often used to drive remediation programs at sites with waters that have been affected by mining activities. In the past, these levels were sometimes chosen without rigorous statistical and geochemical analysis. A probability-distribution approach was used at the Sweetwater Uranium Project to separate a large set of geochemical data into populations that represent contribu¬tions from different sources. Natural background populations were identified for major ions, metals and radionuclides, and these were submitted to the US Nuclear Regulatory Commis¬sion (NRC) to modify the extent of a corrective-action pro¬gram and to establish control limits for future monitoring.

Jan 1, 2000

By S. Gallagher, A. Mayton, R. Merkel

The prolonged exposure of equipment operators to shock and whole-body vibration (WBV) is linked to cumulative back, neck and abdominal disorders. In low coal mines, space restrictions make it difficult for seat suspensions to isolate operators from shock and WBV. Researchers at NIOSH's Pittsburgh Research Laboratory are responding to these issues by investigating viscoelastic foams. For the full-load case, an ergonomic seat made with viscoelastic foams can isolate the shuttle-car operator from shock at 15 Hz. Researchers used results from additional foam testing using an analytical model to identify viscoelastic foams that provide shock isolation at a frequency below 5 Hz.

Jan 1, 2000

By J. J. Kellar, W. M. Cross, H. Du, C. D. Struckman, D. A. Boyles

Silane coupling agents have been used in the filler industry for years. One particularly unique feature is the ability of the coupling agents to enhance the adhesion between filler and polymer matrices. This paper will review the use of coupling agents for polymer matrix composite applications and discuss a new approach to coupling agent chemistry, namely, direct formation of a silicon-carbon non-hydrolyzable linkage between glass and coupling agent. The grafted silane monolayers were evaluated by infrared spectroscopy to ascertain their surface coverage and relative stability. Finally, composite specimens were fabricated and their mechanical properties were compared with traditional silane coupling agent treatment.

Jan 1, 2003

By R. K. Mehta, G. T. Adel

A review of the literature reveals that methods for simulating the coupled behavior of size reduction and liberation are limited to binary mineral systems containing one composite particle class. The aim of this paper is to describe the development of a mathematical model to simulate such behavior for binary and ternary systems containing multiple classes of composite particles. A modified Levenberg-Marquardt algorithm and a finite difference Jacobian are used in conjunction with the developed model and a set of constrained equations to estimate all kinetic parameters. This estimation scheme is validated far a binary ore (sphalerite-dolomite) with five composite particle classes using experimental data.

Jan 1, 1991

By E. H. Ahrens

This paper deals with the responsibilities of an operating geologists and the relationship of operations to exploration. It should be of interest to those soon to enter the profession, those new to pining geology and as a review to more experienced geologists. Subjects discussed include detailed geologic mapping, sampling, core logging, assaying, selection of proper map scale, posting geological and assay data, section preparation, identification of ore controls, delineation of development drill targets and geologic hazards, models and the very important topic of salesmanship. Methods and ideas, proven valid in vein, pyrometasomatic replacement and porphyry copper deposits are presented. Hopefully, these will smooth the path for new members of our profession.

Jan 1, 1992

By B. K. Parekh, W. M. Goldberger

Sludge obtained during the production of magnesium (Mg) from molten MgCl2 by electrolysis contains entrapped magnesium particles. The sludge containing the magnesium particles is a friable, continuous matrix of frozen salts that may also contain some oxides and impurities. Due to the high reactivity of magnesium metal with water, a dry process was developed to recover magnesium metal from the sludge. The process utilizes mineral-processing unit operations. The steps include selective comminution, screening, attritioning and tabling. Recovery of the high-grade (>90%) metal was in the 70% range. The novel process was also successfully applied to a magnesium-alloy for the recovery of metal from the sludges.

Jan 1, 1997

By Serge Payant, Michael G. Li, Lionel J. J. Catalan

Alkaline solution rinsing for decommissioning of an acid-leached residue was evaluated by column experiments, neutralization tests and solid characterization by XRD and SEM. It was found that consumption of a strong alkali during residue neutralization was much greater than that required to neutralize the soluble acidity. The excess alkalinity was consumed by solid-phase conversions unnecessary for the success of decommissioning. Alkaline rinsing did not reduce the time requirement for decommissioning when compared with plain water rinsing. Since no benefit is gained to compensate for the additional costs associated with excess alkali consumption, we conclude that strong alkaline solution rinsing is in fact inferior to simple water rinsing.

Jan 1, 1998

By Thomas H. Hibner, Daniel Tempelis, John E. Shamma

Environmental protection of nearby resources is an issue that can not be ignored in tunnel construction. The Inland Feeder Arrowhead Tunnels Project is no exception. With keen interest from various stakeholders, Metropolitan developed a Groundwater Monitoring and Mitigation Plan. This plan provides for monitoring and management of selected water resource features within the San Bernardino National Forest along the proposed tunnel alignment. The plan specifically provides for monitoring of streams, springs, seeps, and piezometers for water temperature, pH, specific conductance, and chemical analyses, as well as flow or groundwater elevation. Metropolitan uses the data to evaluate for and manage potential impacts from groundwater ingress during construction of the Arrowhead Tunnels.

Jan 1, 2003

By J. T. Crawford

A comprehensive strategic-planning model was developed for the phosphate strip-mining and chemical operations at White Springs, FL. The computerized model covers orebody modeling, production simulation and financial analysis. The model has several innovative features, including the use of NPV techniques in orebody block economics, the adaptation of the floating-cone method to a floating template for generating dragline mining units automatically, the use of interactive graphics for designing mining units, and the use of a dragline move economics algorithm for the automatic scheduling of mining-unit assignments and moves. The simulation of chemical-plant production uses linear programming and concentrate inventory levels to control mine-operating schedules.

Jan 1, 1999

By V. R. Degner

Given: the process tonnage, performance objectives, and plant floor area, the paper will outline the metallurgical and machine hydrodynamic scale-up procedures for translating the lab flotation test results to the design of a full size flotation machine installation, including the machine number, size, and arrangement. Machine selection considerations for rougher, scavenger and cleaner duty, and special considerations relative to specific applications, will be summarized where appropriate. The value of kinetic modeling in quantitative metallurgical (lab to full size machine) scale-up will be reviewed considering a coal installation, and design information for additional applications such as copper, molybdenum, iron, phosphate, and potash will be discussed.

Jan 1, 1986

By John Carson

Belt feeders are commonly used to meter the flow of bulk solids from bins and hoppers. If the interface between the hopper outlet and belt feeder is not designed correctly, flow from the bin may be severely compromised, resulting in problems of no-flow, segregation, flooding, etc. By knowing the flow characteristics of the bulk solid being handled and applying proven design techniques, such problems can be avoided. Relevant bulk solids flow characteristics are identified, along with measurement techniques. Design procedures for correcting problems with existing feeders as well as proper design of new feeders are presented, along with case histories of successful application of these procedures.

Jan 1, 2008