Search Documents

By Milka Madahana, John Ekoru

Particulate matter is one of the leading pollutants in the mines and in the communities in the areas near or surrounding the mines. The availability of large Clinical and environmental data sets obtained from the mines has brought about the need to use better approaches to analyze the collected data. Prediction and control of particulate matter concentration in the mining environment is essential in minimizing air pollution and protecting the respiratory health of mine workers. The main objective of this research work is to analyze datasets obtained from a mining area using machine learning techniques which will then be followed by the real-time estimation of dust particulate in the mines. Datasets collected over 8 years in an hourly sampling rate from an open cast mine is cleaned and analyzed for trends and patterns. Artificial Neural Networks (ANNs), Support Vector Machines and decision trees techniques are applied to analyze and predict the particulate concentrate. The estimation of particulate concentration using Artificial Intelligence will significantly contribute toward the development of quantitative tools to be used in correlating of cause and effect of dust concentration in mines. The results obtained in this work will form a sub-unit of a respiratory health monitoring system for mine workers. The system is essential in the collection, analysis, and tracking of mine workers’ respiratory health, thus it forms part of an early intervention system for mine workers. From the existing theory, we expect the Artificial Neural Network will perform much better than previously used classical models.

Jun 25, 2023

By W. B. Greer, J. J. K. Daemen

Introduction The performance of seals in boreholes, shafts and tunnels is an important concern in mine safety, in the control of effluents from operating and abandoned mines and in the underground containment of hazardous wastes (Einarson and Abel, 1990; Mining Waste Study, 1988). Despite the clear need for effective seals, few documented test results are available concerning the performance of in situ seals. Some evidence indicates that horizontal or near-horizontal holes are especially difficult to seal properly (Kelsall et al., 1982). This research involved the installation, extensive hydraulic testing, removal and post-test examination of a 10-cm-long x 10-cm-diam cement grout seal in a near-horizontal borehole in limestone. The work was performed in an underground mine on Marble Peak in the Santa Catalina Mountains, AZ. A test hole was diamond cored in the recrystallized limestone of the Escabrosa formation. The hole is 33.24 m long, 10 cm in diam, and dips at 10.4°. The hole extends between two drifts and thus is accessible from both ends. Seal installation Surveys to assist in selecting the interval to seal consisted of core logging, video logging and constant-head injection tests using a straddle-packer unit. The location selected, 3 m from the lower end of the hole, had low hydraulic conductivity (3 x 10-10 to 3 x 10-9 cm/sec) and was free of significant fractures. The grout used, an expansive Class A cement, was provided by Dowell-Schlumberger, Tulsa, OK. A grout mass about 1.5 m in length was installed, with a dump bailer, above a temporary mechanical plug. Groundwater in the hole, if any, was minimal during placement. After 13 days of curing, the grout mass was partially drilled out from both ends, leaving a seal 10 cm long. Water distribution in rock mass The distribution of water and fluid pressure in the rock mass near the seal appears to be complex. The generally dry condition of the borehole and rock mass suggests that the rock mass near the seal was unsaturated prior to the injection tests of this research. The injection tests presumably created an expanding saturated zone around the seal. However, anomalously high fluid pressures, consistently recorded by one of two piezometers installed near the seal, suggest connection to a source of significant natural hydraulic head. Comparable head variations for closely spaced piezometers have been reported by others (Sowers, 1976). [ ] Seal testing The seal was tested for 3.5 years, using steady constant-head, tracer travel-time, dye-injection, head-buildup and transient constant-head tests. These tests are fully described in Greer and Daemen, 1991. In the head-buildup test, transient flow occurs through the seal (and rock mass) to a closed, water-filled interval of the borehole adjacent to the seal. The test consists of monitoring the rise in head in the closed interval until steady conditions are approached. The test may be analyzed in terms of a one dimensional analytical model to obtain the effective hydraulic conductivity (Ks) and specific storage (Sss) of the seal. Analysis in terms of an axisymmetric three-dimensional numerical model may yield properties of both the seal and rock mass.

Jan 1, 1993

By E. D. Gálvez, L. A. Cisternas, A. López-Valdivieso, F. Lucay

"The floatability of molybdenite fines in saline solutions was investigated through microflotation studies using a modified Hallimond tube. In addition, the effect of pH and gypsum precipitation from calcium ions (Ca2+) and sulfate ions (SO4 2-) ions in saline water on the recovery of the molybdenite was analyzed. It was found that the floatability of molybdenite fines significantly increased with the ionic strength of the saline solutions and is independent of pH above 0.5 mol/L ionic strength. The high floatability of molybdenite in saline solutions is explained as being due to the low electrostatic repulsion between bubbles and the edges of molybdenite particles, which is exceeded by interactions due to van der Waals and hydrophobic forces. The precipitation of Ca2+ and SO4 2- ions as gypsum had a detrimental effect on the natural floatability of molybdenite because of gypsum crystal attachment on the faces of the molybdenite particles. This precipitation phenomenon may be initiated in copper–molybdenite flotation circuits that use recycled saline water, like seawater containing Ca2+ and SO4 2- ions.IntroductionWater availability is a significant factor in mining projects. Water, particularly fresh water from rivers and underground water, is becoming a scarce resource for mining operations and new projects. Under these circumstances, the use of water with high concentration of salts in flotation plants is becoming increasingly important (Cisternas and Moreno, 2014). The use of seawater has been studied as a sustainable solution for many mining companies in dry areas located near the sea. Notably, using seawater in mining operations is how mining companies in Chile have coped with the problem of water resources (Cisternas and Gálvez, 2014). In 1930, small plants in Chile used seawater to float chalcopyrite from high-copper-grade ores. In 1975, the results of tests in pilot plants for the flotation of copper minerals with seawater were reported. It was found that froth formation in seawater at pH 9.5 was suitable to make the rougher circuit work properly, even without frothers. The Cenizas mining group successfully floated chalcocite, bornite and chalcopyrite in the Las Luces plant in Taltal in Chile using seawater (Moreno et al., 2011). Minera Centinela (Antofagasta Minerals S.A. Chile) is currently processing porphyry copper ores using a seawater mixture consisting of 20 percent fresh seawater and 80 percent recycled water. Lower consumption of flotation reagents was reported in both seawater and salt water. In addition, studies performed with synthetic seawater showed that certain frothers increase the froth volume, whereas others decrease it. Additionally, the froth produced with seawater carries a high amount of gangue, and low-quality concentrates are obtained, requiring more cleaning stages."

Jan 1, 2015

By Hee-Young Chung, In-Mo Lee, Jeongjun Park, Hangseok Choi, Seok-Won Lee

"When using a Tunnel Boring Machine (TBM) during tunneling work, unexpected ground conditions can be encountered that are not predicted in the design stage. These reduce the stability of tunnels, and can result in considerable economic losses. This paper analyzes the potential risk events that may occur due to risky ground conditions. A resistivity survey is utilized to predict the risky ground conditions ahead of the tunnel face during construction. The potential risk events are evaluated considering both the occurrence probability and the impact. A TBM risk management system that can suggest proper solution methods for potential risk events is also developed. Multi-Criterion Decision Making (MCDM) is utilized to determine the optimal solution method to handle risk events. Lastly, an actual construction site, at which a risk event occurred during tunnel construction, is analyzed utilizing the Earth Pressure Balance (EPB) Shield TBM, to verify the efficacy of the proposed system.INTRODUCTION The Tunnel Boring Machine (TBM) method has been widely adopted in numerous tunneling projects because, as a mechanized tunneling method, it is also environmentally friendly, exhibiting minimal noise and vibration when compared with conventional tunneling method. In addition, it provides considerable economic benefits that allow for a high advance rate for long drives during construction. However, the TBM method has a limitation, as it is unable to deal with unexpected situations during construction, as the system is not capable of moving backwards. This leads to delays or even stoppages, and a corresponding increase in construction costs due to the need to arrange for alternative equipment and solutions. It is essential to retain systematic management in order to prevent or deal with unforeseen consequences such as the collapse of a tunnel face, ground surface upheaval or settlement, and construction delay due to water leakage during construction. Therefore, a systematic risk management system that is applicable during the construction stage of the TBM tunnel should be developed, taking into account the predicted risky ground conditions ahead of the tunnel face in advance."

Jan 1, 2016

By K. Boakye, T. Newman, P. Bláha, M. B. Toelle

"This paper presents a quarry optimization plan using a block model and an in-house development quarry scheduling and optimization software (QSO Expert) to help improve quarry operations at Crystal River. The Crystal River Quarry is an underwater quarrying operation that barges limestone via the Gulf of Mexico, as the main source of raw material to a cement plant in Theodore, Alabama. To improve the quarry operation, an evaluation was completed to optimize the quarry planning and extraction procedures of the quarry. In order to achieve this, additional exploration drilling campaign was implemented, a new block model was re-calculated and the latest version of QSO Expert software was used. The primary economic impact is a higher recovery of limestone reserves; sustainability of resources, corresponding longer quarry life. Secondarily as the limestone is mined underwater and stockpiled above water, drainage reduces moisture content achieving direct cost reduction on limestone shipping. In addition, a considerable reduction in operational cost was achieved due to a significant decrease in consumption of electrical energy, reduced dragline maintenance costs and reduced dragline movements within the operation. INTRODUCTION Holcim is a Swiss-based global building materials and aggregates company. Founded in 1912, the company expanded into France and then throughout Europe and Middle East during the 1920s. In 1922, Holderbank, as the company was then known, expanded beyond the Swiss borders into France. By the end of the decade Holderbank held stakes in Belgium, Germany, the Netherlands, and Egypt (Holcim History 1912-2012) Positions in Lebanon and South Africa soon followed.. Holder bank later expanded in North America in the 1950’s. In the late 1970s and early 1980s, Holderbank continued its expansion in Latin America, Asia and Spain for the first time. The company expanded into Eastern Europe and experienced a boom in Spanish construction preceding the 1992 Summer Olympics. By 1986, Holderbank was the world's largest cement manufacturer. In the 1990s, the company consolidated its European holdings as the American market drove growth. Expansion into Eastern Europe and Russia continued (Holcim History 1912-2012). In 2001, the company changed its name from ""Holderbank Financière Glaris"" to Holcim (short for Holderbank ciment) (Holcim History 1912-2012). Holcim expanded by purchasing Aggregate Industries entering into the United Kingdom for the first time. That year, the company also expanded into India by acquiring a stakes in The Associated Cement Companies (ACC) and Ambuja Cement Eastern. In 2008, Holcim became the largest shareholder of China's Huaxin Cement with a 40% stake. In 2009, they acquired Cemex Australia. In 2014, Holcim and Lafarge announced they had agreed to terms on a ""merger of equals"" valued at nearly $50 billion in 2015. The new company LafargeHolcim based in Switzerland has a manufacturing capacity of 427 metric million tons a year."

Jan 1, 2017

By Siddhartha Roy, Hemant Agrawal, Ram Madhab Bhattacharjee, Devi Prasad Mishra

Heat stress is a major concern for the health, safety and productivity of miners working in hot and humid underground mines. At greater depth, heat inside underground mines increases due to geothermal gradient, heat released from high-capacity machinery, exposed rock surface, auto-compression of air, human metabolism, etc. Prolonged physical work in thermal environments severely affects the health, safety and efficiency of miners. In order to address this important issue, a systematic literature review (SLR) has been conducted. This SLR aimed to identify the research gap in the area of heat stress effect on underground miners and its control. An extensive literature search was carried out on numerous digital databases, grey literature and conference proceedings to identify relevant research work for this review. Moreover, the impactful studies, methodologies and preventive measures undertaken during the past five decades on the effect of heat stress on underground miners were retrospectively analysed, with a broader aim to explore the need for further research on this pertinent topic. Overall, 571 references were identified from the literature review, out of which 51 research articles addressing the sources of heat, heat stress effects on miners, heat stress indices and control measures for heat stress in underground mines were selected as primary papers for detailed review. Pre-developed fatigue is one of the prime causes of health hazard, safety and productivity loss of miners working in underground high heat stress zones. Hence, development of a better heat stress index integrating personal, environmental parameters and pre-developed fatigue (PDF) of miners is essential.

Jan 14, 2022

By Peter Zhang, Daniel Su, Heather Dougherty, Jack Trackemas

"Longwall mining has a significant influence on gas wells located within longwall chain pillars. Subsurface subsidence and abutment pressure induced by longwall mining can cause excessive stresses and deformations in gas well casings. If the gas well casings are compromised or ruptured, natural gas could migrate into the mine workings, potentially causing a fire or explosion. By the current safety regulations, the gas wells in the chain pillars have to be either plugged or protected by adequate coal pillars. The current regulations for the gas well pillar design are based on the 1957 Pennsylvania gas well pillar study. The study provided guidelines for gas well pillars by considering their support area and overburden depth as well as the location of the gas wells within the pillars. As the guidelines were developed for room-and-pillar mining under shallow cover, they are no longer applicable to modern longwall mining, particularly under deep cover. Gas well casing failures have occurred even though the chain pillars for the gas wells met the requirements by the 1957 study.This study presents seven cases of conventional gas wells penetrating through longwall chain pillars in the Pittsburgh coal seam. The study indicates that overburden depth and pillar size are not the only determining factors for gas well stability. The other important factors also include subsurface ground movement, overburden geology, and weak floor, as well as the construction of gas wells. Numerical modeling was used to model abutment pressure, subsurface deformations, and the response of gas well casings. The study demonstrated that numerical models are able to predict with reasonable accuracy the subsurface deformations in the overburden above, within, and below the chain pillars, and the potential location and modes of gas well failures, therefore providing a more quantifiable approach to assess the stability of the gas wells in longwall chain pillars.INTRODUCTIONIn the eastern United States, abundant gas wells have been drilled through coal seams that are being actively mined by longwall mining. The existence of gas wells in the U.S. coal fields, whether active or abandoned, have caused many issues for longwall mining. First of all, any gas well in the mining area has to be located by all possible means. Secondly, the gas wells within longwall panels have to be plugged, as cutting through gas wells will allow natural gas to flow into the active longwall mines. On the other hand, the gas wells within longwall chain pillars or barrier pillars can be left in place if the wells are protected by properly designed pillars."

Jan 1, 2019

By George H. K. Schenck

It seems appropriate to review the history of mechanization of our underground coal mines at this time when many favorable flags are flying for this industry. It is a reasonable hope that such a review may stimulate thinking as to the directions that new technological developments are apt to take and in which members of the Society of Mining Engineers are destined to play important roles. Discussion of the relative importance of the various changes that have taken place since the advent of electric power provides the starting point. It is in the economic factors utilized that we find conditions which permit more efficient utilization of the capital committed to the industry. Concepts rather than specific items are emphasized in the following discussion because once the value of a concept, such as mechanical conveyors, is established, it then spawns many variations which are not significantly different. The shift from animate to inanimate energy has been the most important change in the modern industrial scene, including coal mining. Although introduced into coal mines for some purposes early in the period of general electrification, the coal industry adopted mechanical power relatively slowly, and 1944 was the first year in which a majority of deep-mined coal was mechanically loaded.

Jan 1, 1968

By P. A. Cornejo

Blastings always generates induced vibrations through seismic wave, these are lost energy from the blasting and therefore causing the disturbance of slopes and structures near the blast source. Most of the components of an open pit mine have to reach a physical stability, especially during its closure process. Aiming to develop a vibration prediction model using the historical records from an open pit mine located on Peru, this research has two main focuses depending on the distance from the blast source to the structure: to protect the final slopes and to protect the villagers houses. Both are based on the Devine model of the Square Root Scaled Distance (SRSD) to predict the Peak Particle Velocity (PPV). The Mid field model, where is found mainly final slopes from the pit, limited by the failure criteria of McKenzie based on the geo mechanical properties of the rock mass. The Far field model ranges distances where are located the most community households, limited by the German rule DIN 4150 for highly sensitive structures. Both scenarios resulted on a distribution abacus to limit the weight of used explosives to get the best operational advantage and structure safety.

Mar 2, 2022

By M. Frenzel, D. Ebert, K. Bachmann, A. D. Renno, R. Möckel, J. Gutzmer, J. Krause

With the increasing demand for metalliferous and mineral raw materials and the consequent depletion of the global natural resource base, the possible utilization of secondary raw material sources is receiving more and more attention. In the present study, we present results from a detailed vanadium deportment study of three basic oxygen furnace slag (BOS) samples known to containing elevated bulk concentrations of vanadium. Complementary analytical methods that were used to quantify the abundance and composition of V-containing phases include SEM-based automated mineralogy, X-ray fluorescence analysis, and X-ray powder diffraction as well as electron probe microanalysis. The vanadium deportment was quantified using Monte-Carlo simulations of the data obtained from automated mineralogy and electron microprobe analysis. The total V concentrations identified by XRF are between 1.7 and 2.2 wt.% V. The most important hosts of vanadium are larnite-, brownmillerite- and portlandite-solid solutions. In two samples Ca carbonates also significantly contribute to the V deportment, while wuestite, lime, and native iron do not contribute significantly to the vanadium deportment. A thorough consistency check identifies considerable uncertainties in the density of the V-bearing phases as the most likely reason to explain remaining discrepancies between measured and calculated V values.

Oct 14, 2023

By RIINA SALMIMIES, Paula Vehmaanperä, Antti Häkkinen

The dissolution of iron oxides in mixtures of acids is fairly uncommon but can result in a more efficient dissolution process. The objective in this work was to investigate the dissolution of synthetic hematite powder in mixtures of oxalic and sulfuric acid. Experiments were done at different acid ratios and temperatures. An increase in temperature from 15 to 35 °C increased solubility, whereas an increase from 35 to 50 °C did not change the solubility but had a profound effect on the kinetics. An important finding was that oxalic acid advanced the dissolution process since increasing the amount of oxalic acid in the system resulted in faster kinetics and higher solubilities. The dissolution kinetics were well described with the Kabai model, which was the only studied model able to describe the whole reaction time. However, the solid specific constant a varied for the different acid ratios and this is argued to be a result of changes in the solid phase. The changes in the constant a were not in line with the original study of Kabai, which indicates that a cannot be the solid specific constant but it can be the constant connected to dissolving media describing the changes in the dissolution mechanism.

Sep 23, 2020

A Mark IV surface force apparatus (SF A) was used to conduct direct force measurements in dodecylamine hydrogenchloride collector solution between mica surfaces at varying pHs. It has been found that the long-range hydrophobic forces reach a maximum at pH 9.5, which also corresponds to the maxima attained by the contact angle and flotation recovery of quartz. The charge densities are comparable on both mica and quartz surfaces (0.40-0.48 run2), making it possible to draw conclusions on the flotation of quartz from the direct force measurements conducted on mica. Therefore, it may be suggested that the maximum flotation recovery of quartz m the range of pH 8.0-10.3 may be attributed to the appearance of long-range hydrophobic force, which in turn can be related to the formation of a close-packed monolayer (or hemimicelle) in the presence of neutral amines formed as a result of hydrolysis.

Jan 1, 1996

By Gerald H. Luttrell, Seyed Hassan Amini, Aaron Noble

One of the most important processing engineering tools for designing mineral processing facilities is linear circuit analysis. This technique, originally conceived and developed by Meloy, Williams, and Fuerstenau nearly four decades ago, provides fundamental insights regarding how unit operations interact and respond when arranged in multi-stage processing circuits. Researchers have successfully utilized this tool to improve the operating performance of industrial processing circuits incorporating coal spirals, magnetic separators, mineral spirals, and eddy current separators. More recently, advanced versions of this tool have also been developed to provide a standardized framework for circuit mass balance calculations, to output exact analytical solutions to mass yield and value-based efficiency expressions, and to estimate uncertainty propagation in separation circuits. This article reviews the historical development of linear circuit analysis, describes how the technique has evolved to address more complex circuit design problems, and presents industrial case studies that highlight the importance of this process engineering tool.

By Guillermo V. Borquez

The economics of open pit mine design are dictated by three basic elements: cut-off grade, stripping ratio and slope angle. Although these elements are functions of a number of independent parameters, they are interrelated through their influence on the overall economics. The optimum slope angle is the most uncertain element to determine, because rock mass properties are difficult to obtain. However, for preliminary estimation, the slope angle can be determined from the relationship between the probability of failure and the safety factor. The economics of the slope selected will depend on a profit versus risk judgment. In this paper, the author will present an actual case of application of this postulate.

Jan 1, 1977

By P. Corser

Operational and geotechnical constraints on mining within steeply dipping deposits and historic landslide areas, which are characteristic of subarctic coal deposits in Alaska, will be discussed. The current plan for mining through these areas will be presented, as well as an alternative plan for minimizing the adverse effects of mining through an historic landslide area.

Jan 1, 1988

Characterization of ore and waste-rock material using automated quantitative micro-mineralogical techniques (e.g., QEMSCAN® and MLA) has the potential to complement traditional acid-base accounting and humidity cell techniques when predicting acid generation and metal release. These characterization techniques, which most commonly are used for metallurgical, mineral-processing, and geometallurgical applications, can be broadly applied throughout the mine-life cycle to include numerous environmental applications. Critical insights into mineral liberation, mineral associations, particle size, particle texture, and mineralogical residence phase(s) of environmentally important elements can be used to anticipate potential environmental challenges. Resources spent on initial characterization result in lower uncertainties of potential environmental impacts and possible cost savings associated with remediation and closure. Examples illustrate mineralogical and textural characterization of fluvial tailings material from the upper Arkansas River in Colorado.

Feb 27, 2013

For the past two years, Cliffs Natural Resources in Minnesota has tried an experiment: it has staffed a booth at the Iron Range Earth Fest. ?It was a little unusual for a mining company to participate in an event that centers around preserving the Earth?s resources,? said Julie Lucas, environmental manager at Hibbing Taconite Company. ?But Cliffs is a sustainable company and we want to take every opportunity to share information about our practices. We found the response to be overwhelmingly positive.? Cliffs? outreach effort is just one of the surprising ways mining companies across Minnesota are reaching out to stakeholders and finding success. The 85th annual SME Minnesota Section Meeting (73rd Annual University of Minnesota Mining Symposium), held April 17-18 in Duluth, MN, demonstrated the Minnesota mining community?s commitment to connection and collaboration, and how that approach is bringing success.

Jan 1, 2012

By S. Frisch

Selenium (Se) in effluent waters has become a significant challenge for a number of industries. Toxicity studies and new reports of occurrence have certainly caused increased scrutiny and actions in the mining industry today (Sandy, DiSante, 2010). While initial activity in addressing selenium-laden waters were conducted in the coal mining industry, today a much broader range of mine types are beginning to search for solutions to selenium treatment of their mining waters, including both hard rock mining operations (gold, nickel, zinc, etc.) and soft rock mining (phosphate, uranium, etc.) Throughout North America, new regulations covering selenium discharge are either in place or being developed. While a number of physical/chemical approaches show promise in selenium treatment, when considering optimal cost and treatment efficacy issues, biological treatment ? particularly fixed-film biological treatment - is reported to be one of the most promising approaches to managing selenium-containing waters. Among biological treatment options, the fluidized bed reactor (FBR) has undergone extensive pilot testing for Se treatment in the last three years, including eight pilot programs, and the first FBR system is now operating at a coal mining site. In all tests, the FBR has been shown to be a highly cost-effective approach to selenium treatment based on its physical and performance characteristics. This is consistent with its history for reaching low levels of treatment in similar service for other oxyanions including perchlorate, nitrate and various metals. With the results from the most recent testing, the technology has been shown to be adaptable to an ever-broadening range of influent water conditions and flow rates, in varying terrains and weather conditions. Selenium occurs in various valence states from -2 to +6 (Sobolewski, 2005). The speciation of selenium plays a critical role in understanding the effectiveness of any approach for removal, especially to low levels. Elemental selenium is insoluble and has little effect on living organisms. Colloidal fractions are known to occur. In aqueous environments such as coal mining runoff, selenium is most often found as the oxygenated anions of selenite (SeO32-, Se4+) and selenate, (SeO42-, Se6+). Selenium is commonly found in mining waters in concentrations ranging from 3 to >12,000 µg/L. The U.S. National Primary Drinking Water Standard MCL is 50 µg/L for selenium (EU 10 µg/L; WHO 40 µg/L). The National Fresh Water Quality Standard is 5 µg/L for selenium. The U.S. Fish and Wildlife Service has recommended that the National Fresh Water Quality Standard be lowered to 2 µg/L to protect fish, waterfowl, and endangered aquatic species. Several states have followed with enforcement actions at these same low levels. In Canada, permits may require stakeholders to monitor levels in water or biota, or to comply with guidelines, at either the National or Provincial levels, which can be as low as 1 or 2 µg/L in surface waters. Treatment of selenium in all mining waters presents a series of challenges. It can be present in relatively dilute concentrations and in streams with variable and often high flow rates. It can be present in many soluble and particulate forms, which may affect process design and treatability. The conditions of influent selenium-containing waters can vary, with issues such as temperature, pH, total dissolved solids and other contaminants affecting the ability to remove selenium selectively and economically. Treatment of selenium often results in the generation of a concentrated by-product requiring disposal, and re-release from residuals can occur. Beyond these issues, the physical environment of a mining operation can offer challenges such as remoteness and harsh and/or cold weather. Currently available selenium treatment technology (Table 1) includes biological treatment and a number of physical-chemical processes ? such as ion exchange, membrane filtration and adsorption ? that vary widely in efficiency and cost. Most treatment options remain either too costly and/or unproven for selenium-containing streams for reasons that include poor removal efficiency, variability in volume and composition of influents, system sizing and logistics considerations, as well as operating requirements.

Feb 23, 2014

The Earth?s population is approaching 6.6 billion people. More than half live in urban areas. And, as those figures continue to grow, the need to make wise use of the world?s natural resources as well as its living space will also grow. Thus, the concept of sustainable development ? meeting the needs of the current generation while preserving resources for future generations. The use of underground space is only one part of the sustainable development concept. But it is an important one. Tunnels and underground space are environmentally friendly and contribute significantly to sustainable development. But it takes years to plan and build tunnels and other underground infrastructure. And the demand for infrastructure in the world?s mega cities has grown significantly. In December, about 100 people representing several developed and developing nations spent a day at the United Nations (UN) in New York City discussing the future of underground space development throughout the world. The meeting was put on by the UN?s Department of Economic and Social Affairs and the International Tunnelling and Underground Space Association (ITA). The conference was titled ?The Use of Underground Space as an Unexpected Solution for Promoting Sustainable Development.? Its aim was to promote practical solutions to the use of underground space and tunnels as feasible alternatives to promote sustainable development throughout the world. A panel of speakers from government, academia, the UN and the ITA stressed that development is not sustainable without infrastructure. And, as the world?s population grows, there is now an urgent requirement to efficiently plan for the use of underground space to preserve it for the future benefit of mankind. The benefits of the use of underground space are many, they said. Among them: ? Tunnels channel clean water in and waste water out. This promotes health and sustainability worldwide, particularly in developing countries. ? The use of tunnels and underground space helps conserve energy and increases its efficient use ? the use of tunnels cuts commuting time and so saves energy. ? Tunnels, microtunnels and other underground structures promote the more efficient use of space in large cities ? the bulk storage of water, fuel and other goods. ? Underground structures are subject to less stress than surface structures, making them safe havens for natural and man-made hazards, including earthquakes. And, because underground structures are more durable, lifecycle costs are less than surface structures. ? Underground structures promote the multiple use of available land. Land owner-ship at several layers increases land use and provides more usable space. Han Admiraal is director of the Center for Underground Construction in the Netherlands. He said that urban planners need a new vision concerning the use of underground space. Going underground protects historical and archaeological surface facilities, he said. Underground space use can also protect populations located in adverse climates. And sensitive environmental areas on the surface can also be protected from development. In addition to the transportation of people, freight and water, underground development can also store water, as well as provide storage for waste, hazardous materials, carbon dioxide and geothermal energy. The upshot of this new awareness and vision for under-ground space is that its use should be considered before surface development, Admiraal said. And planners and developers are placing more emphasis on underground space development as part of their overall development plans for urban areas. That was not always the case, he said. In the past, underground space was not considered until after the surface space had run out, he said.

Jan 1, 2008

By P. R. Taylor

Recent research by the investigators has evaluated the oxidation roasting of refractory gold concentrates in the presence of hydrated lime. (Taylor, 1990, 1991, 1992, 1993). These results have indicated that it may be possible to roast concentrates in such a way as to contain nearly all of the sulfur and arsenic in the roaster calcine and that cyanidation may be possible. To further evaluate the behavior of this type of roasting system a laboratory cyclone reactor was built and operated using pyrite and hydrated lime as a .model system. Approximately 50 years ago, the principle of cyclone firing entered practical boiler construction. The appeal of the cyclone configuration was that it afforded the flash combustion process greater efficiency due to turbulence-induced increased mass transfer, heat exchange, and combustion rates.

Jan 1, 1994