Search Documents

By H. Bradley Johnson

A number of Federal laws affecting safety and health in the mining industry has been enacted and revised over a period of many years. We have tended to classify these laws and their applicability into three categories: 1) coal mines, 2) metal and nonmetallic mines, and 3) mines with Federal supply contracts. With the growing attention which is being given to mine safety by the Federal government, the entire mining industry should keep aware of all developments in the administration of each of these laws.

Jan 1, 1970

By B. Pesic

This is an extension of the work on recovery of silver and manganese from Ag-Mn ores, and recovery of silver and gallium from flue dust from phosphate industry. Carbon adsorption was considered as the most adequate method for recovery of silver from thiourea leach solutions. For this reason it was decided to examine the characteristics of adsorption of silver on activated carbon. Coconut hard shell activated carbon was used for this study. Ag(TU)2C1 complex was dissolved into thiourea solution to give 2 gpl stock solution. Thy studied parameters were: loading isotherms at 25°C, 35°C, and 45°C, initial kinetics as a function of thiourea concentration, temperature, pH, N2, and O2. It was found that the loading capacity of carbon for silver and thiourea was 137-150 mg/g and 514 mg/g, respectively, at 25 °C.

Jan 1, 1986

By William F. Lawrence

Within ten to fifteen years, coal-fired power generating stations will be producing over 40 million tons of coal-ash annually in the United States. The largest part of this ash will be emitted from the boilers, entrained in the off-gas stream and trapped as flyash. However, about 15 percent (six million tons) will he removed from furnace bottoms as bottom ash or molten coal-ash slag. In current practice, the molten coal-ash slap is generally water quenched and then transported either as a slurry or in granular form to storage or disposal areas. Although a small amount of this slag is marketed as abrasive grit or as roofing granules, most of it is considered a waste material which must be disposed of at considerable cost to the power companies and therefore to the public. The accom¬panying economic loss in terms of unused raw materials and displaced land is not as obvious but is just as real. The Coal Research Bureau at West Virginia University under the sponsorship of the U. S. Bureau of Mines has been examining the possible utilization of both coal-ash slag and flyash in the mineral wool industry as a method of partially alleviating the growing national problem of solid waste disposal. The potential marketing situation for mineral wool manufactured from coal-ash is illustrated in Figure 1. This bar graph depicts the growth in value of mineral wool shipments1 from 1949 through 1966. In this 17-year period, the value in¬creased by over 350 percent, more than 20 percent per year, despite a decrease in unit cost of mineral wool. It therefore appears likely that coal-ash could find a steady market as a supplement to existing sources of raw materials for mineral wool production.

Jan 1, 1970

By Robert H. Raring

Viewed abstractly, a mill may be defined as a mineral processing facility located somewhere between the mine and the tailings storage area, Just how mining operations and the demands of tailings storage affect mill design is, the subject of this paper. At the outset, it will be readily acknowledged that no two installations can, or ever will be the same. At one extreme is the bucket line dredge where the distance between the ?mine? and the tailings area is measured in terms of tens of feet. At the other extreme, the large open pit copper mines are frequently spread across twenty, miles or so of countryside with the ore moving to the mill, as exemplified by the operations at Bingham Canyon, Ray, or Ruth - the "upstream" counterparts of Garfield, Hayden and McGill. In each of these cases, mill location was largely determined by requirements for tailings storage and/or water supply.

Jan 1, 1961

By J. R. Klaehn, M. Shi, T. E. Lister, L. A. Diaz, J. S. McNally

Since 2019, approximately two dozen international battery recycling companies have been operating at the commercial or pilot scale [1]. However, current process capacity does not exceed 100,000 tons of end-of-life (EOL) lithium-ion batteries (LIB) per year, and the current recycling rate is only about 5% in North America [2-3]. Recycling metals from EOL LIBs is not only essential to waste minimization and environmental stewardship, but also a source of critical materials, which can contribute towards supply chain stabilization. LIB recycling can be roughly divided into three categories: direct recycling, pyrometallurgy, and hydrometallurgy. Direct recycling seeks to retain as much of the manufactured effort with minimum chemical processing [4]. The evolution of battery designs and chemical compositions are challenges to this approach [5-6]. Pyrometallurgical processes are robust and flexible allowing a broad spectrum of batteries with minimum pre-processing requirements. Some of the matrix issues are solved through combustion of some constituents. Smelting is strongly tied to fossil energy and air emissions are a concern. In addition, pyrometallurgical processes are not stand alone, as hydrometallurgical refining normally required to separate and recover the metals of interest (Co, Ni, and Cu) from the produced alloy and Li from the slag [7]. Hydrometallurgical processes can be highly selective and efficient in recovering high purity materials [8]. In general, hydrometallurgical processes are considered cleaner and less costly than high temperature processes [4,9-10]. Extensive chemical consumption and waste generation significantly increase the operating costs and overall environmental impact of the hydrometallurgical processes [11]. Leaching of metals from LIBs is dominated by the mixture of sulfuric acid (1 to 4 M H2SO4) and hydrogen peroxide (1 to 15 wt.% H2O2) [10]. Although organic acids have been tested as lower environmental impact alternatives, the reported pulp density operations are low < 60 g/L [10-11]. For the H2SO4/H2O2 leachates, high leaching efficiencies >90% are reported for Co, Ni, Mn, and Li from cathode materials at temperatures over 40 ⁰C and pulp densities between 30 to 200 g/L [9-10]. H2O2 acts as reducing agent to convert Co+3 and Mn+4 into their soluble forms, Co+2 and Mn+2 [12]. Despite the claims of H2O2 being a clean reducing agent [13], production of H2O2 has significant environmental impacts as determined by life-cycle analyses [13-14]. Moreover, the costs and risks associated with H2O2 transportation and storage cannot be ignored [15].

Mar 2, 2022

By Giuseppe M. Gaspari, Tamara Kondrachova

Contract practices affect cost and schedule of tunneling works, impacting risk allocation between Owners and Contractors. The Authors compiled a dataset of projects constructed in the Toronto Area between 1990–2020 procured either Design-Build or Design-Bid-Build. Data were analyzed identifying independent cost variables across the two methods. Overall industry efficiency further comparison with historical information demonstrates the costs of engineering ongoing escalation due to rising trends in environmental requirements and public consultations stirred through modern communicative platforms. These hard to predict and estimate costs need to be included in the risks evaluated and managed by Owners and not by Contractors

Jun 13, 2021

By J. C. Haptonstall

The Bismark Mine is located in northern Chihuahua, 150 km southwest of Ciudad Juarez. The ore deposit was discovered in 1979, and was placed in production in 1992. The production rate is about 2400 tpd from an ore reserve of 8.5M tonnes. Grades average about 8 % Zn, 0.5 % Pb, 0.2 % Cu and 50 g Ag per tonne. Substantial inflows of water into the under-ground mine complicate the operation. Complex metallurgy poses another challenge for the operators. Bismark was operated through a joint venture, Minera Bismark, S.A. de C.V., with U.S. and Mexican partners, but since early 1993, it is wholly Mexican-owned and operated.

Jan 1, 1994

By Ali Hafiz, Aidin Golrokh, Tom Iseley, Kaz Tabrizi, Saleh Behbahani

In the USA many highway tunnels were built during the 1930s through 1960s. This indicates that these tunnels have exceeded their intended design service life. Based on the initial tunnel inventory conducted jointly by the Federal Highway Administration (FHWA) and the Federal Transit Administration (FTA), more than 526 highway tunnels have been identified in the USA. For understanding the condition of the tunnels and risks associated with deteriorating conditions, comprehensive condition assessments are necessary to mitigate risk and remediate works as required. Monitoring the condition and rate of deterioration of tunnels is vital for timely tunnel maintenance and rehabilitation to avoid sudden tunnel collapse. This session will explain the necessary steps for tunnel inspection and review some of the state of the practice information on tunnel inspection techniques.

Jun 13, 2023

By Reinhard Gertl, Soroush Dabiri, Juan-Carlos de Rueda

The Tunnel of Guillermo Gaviria Echeverri, spanning 6.05 miles, will be Latin America’s longest road tunnel, is currently under construction in Colombia’s Antioquia Department with a single bidirectional tube connected to a parallel rescue tube through multiple cross-passages. The study faces challenges in implementing the prescriptive semitransversal ventilation system due to design restrictions. Different ventilation concepts are eplored to nd the most suitable system for regular operation and re scenarios. A quantitative ris assessment evaluates each alternative system and identies the longitudinal ventilation system, accompanied by ris mitigation measures, as the safest choice, since it surpasses the prescribed semitransversal ventilation concept.

Jun 23, 2024

By P. Tsang

The stability of longwall chain pillars depends not only on the mechanical properties of coal and surrounding rocks, but also geological and mining conditions. In order to evaluate the effects of each, variable, the orthogonal experiment design was employed in this study for significance analysis. The study concluded that the stability of longwall chain pillars is mainly controlled by the ratio of pillar stress to pillar strength, the ratio of Young&apos;s moduluds of the roof to coal and floor to coal, entry width, pillar width and the internal friction angle of coal. Additionally, horizontal stress, panel width and mining height also play a significant role.

Jan 1, 1994

By J. A. Lombardi

Innovative hard rock narrow-vein, longwall, and stope leach mining systems concepts are described and evaluated economically. The principal tool proposed for use in these systems for both mine development and production is the U.S. Bureau of Mines radial-axial splitter. The mining systems concepts are prefeasibility level costed and projected to be cost competitive for steeply dipping veins, 0.6-1.2 m wide, for horizontal tabular ores 2 m -5 m thick, and for leachable ores with greater than a 1.7:1 stripping ratio. In all of the systems the orebody, less swell, is retained underground for use as backfill.

Jan 1, 1994

By W. Fletcher

Startup of a new plant is a very interesting time. It generally is also a very demanding and often frustrating period. Startup problems can become serious ii they impede the early achievement of full plant production. Raw materials are wasted, manpower is unproductive, field modifications can be extremely expensive and market commitments may not be met. This paper outlines a well proven and highly successful approach to eliminating many of the problems and frustrations often experienced in plant startup. The procedures and methods summarized in the following paragraphs have been developed over a period of 25 years during which some 90 plants were started up.

Jan 1, 1981

By Mustafa Kumral, Mehmet Balci

Strategic mine planning focuses on cutoff grade selection, capacity planning and block sequencing. Despite significant knowledge accumulated, potential value can be added to mineral sourcing by addressing various aspects. A case study on a metallic deposit with a lognormal grade distribution examines if grade/metal distribution influences cutoff grade selection. Six data sets with different shape and scale factors, but the same ore tonnage and metal quantity, are analyzed. Results indicate deposits with lower shape and scale factors are more sensitive to metal price and discount rate changes. The study also investigates the effect of economies of scale (EoS) on project value, focusing on the ratio of variable cost to total cost (capacity factor). Two regression analyses are conducted for optimal capacity planning and cutoff grade selection. The first shows capacity planning is highly sensitive to the EoS of mining and mineral-processing costs, with grade variability and metal distribution being negligible. In the second analysis, grade variability and EoS of mineral processing costs are vital for cutoff grade selection.

Sep 1, 2024

By Edward F. Oxford

The area described in this paper lies along the inner margin of the Coastal&apos; Plain in Twiggs County, near the exact center of the State of Georgia. Twiggs is one of four counties which produces approximately 75 per cent of the nationals output of kaolin used in the paper trade. In this vicinity the land surface is characterized by coastal plain hills with elevations ranging from about 250 feet, above mean sea level in the flood plain of: the Ocmulgee River to about 550 feet above mean sea level on the hill tops. Surface drainage in the area is southwestward to the Ocmulgee River, the tributaries of which have dissected the land surface exposing thick sections of the upper parts of the hills of Eocene (Ocala Limestone and Barnwell formation) limestone, sand, marl and clay, and in the lower parts of the hills Cretaceous (Tuscaloosa Formation) kaolin, kaolinitic clay, sandy clay, sand and, gravel. The contact between these two principal groups of geologic units is rather easil distinguished as the top of the kaolinitic beds. It is described in detail and mapped in published geologic reports for the area (LaMoreaux, 1946).

Jan 1, 1968

By Gilbert C. Robinson

Manufacturers of brick and tile are showing growing interest in the possibility of manufacture of a clay bonded block. The block would have the shape of concrete block, but would be made without the use of Portland cement, Instead, the block would be made&apos; from mixtures&apos; of an aggregate and the present raw materials of the brick industry. The finished units would weigh 20 to 30 pounds and meet the specifications for Grade A concrete block. The present status of the clay block development shows one manufacturer actually in production of these units$, two additional manufacturers are attempting production and many manufacturers are actively engaged in development work. At least four major research laboratories are engaged in the development program. There are several different processes available for clay block production. These processes differ primarily in the type of aggregate used or in the type of forming operation selected. I would like summarize these possible methods.

Jan 1, 1960

By Eugie Kabwe

Rock bolts are components of tunnel support structures and their efficacy in reinforcement requires the appropriate estimation of the bolt pre-tension. However, cases of ineffective rock bolt application due to loosening are common which leads to the potential failure of the support structures, thus negatively affecting the tunnel stability. The effective employment of pre-tensioned bolt within support structures requires an appropriate installation tension as a result of sufficient bolt head/nut pre-load. Henceforth, this paper presents a load indicator washer (LIW) capable of withstanding assigned static loading as well as provides an appropriate pre-tension. The different LIW breadths are numerically analysed in the finite element code (ABAQUS) to estimate deformation when a designated 60-kN pre-load is applied. The numerical simulation employs a bi-linear isotropic hardening constitutive law governed by the von Mises yield criterion. The simulation also considers the nominal temperature of the nutLIW-rock bolt connection. Therefore, a long-term relaxation effect on bolt pre-tension as a result of stress relaxation is neglected. The compressive force required to achieve the LIW-predetermined deformation is the bolt pre-tension. It is drawn from the simulation results that the 1.5-, 2.0-, 3.0-, 3.5-, and 4.0-mm-thick LIWs are completely flattened when subjected to 28-, 42.5-, 65-, 76-, and 88-kN pre-load respectively.

By P. G. Corser

A gold and silver open-pit mine located in northwestern Chile contracted ACZ in 1991-92 to assess the stability of their spent ore pile and to determine the cause and magnitude of cyanide contamination associated with leaching operations. The mine is a conventional open-pit located at an elevation of approximately 4,800 meters (m.) (15,744 feet). A spent ore pile is located approximately 2,000 m. southwest of the mine and approximately 1,000 m. northeast of the active pad and plant facilities. The pile was constructed on a gentle northwest slope dipping 12 to 13 degrees. The pile is bordered by a small river to the northwest and by a larger river to the northeast. Both rivers eventually flow into Bolivia. Heap leaching and processing commenced at the mine in 1988. Since 1988, nearly 6.0 million tons of ore at an average grade of 1.96 grams/ton (0.07 ounces/ton) of gold and 52 grams/ton (1.83 ounces/ton) of silver have been treated by cyanide heap leach methods with zinc (Merrill Crowe) precipitation. In approximately three years of operation, the mine has yielded more than 225,000 ounces of gold and over 1.5 million ounces of silver. Currently ore is agglomerated and hauled to the leach pad by truck and is top loaded to produce a 5-meter lift height. Four contiguous reusable (on/off) leaching pads were constructed with an asphalt layer above a carefully compacted sub-base of High Density Polyethylene (HDPE) liner and screened fines. Leach solution of pH 10-11 containing 1.2 to 1.5 gram/liter of cyanide is applied to the heap at a rate of 10 liter/hour/square meter for a total active application period of 30 days. Leached (spent) ore is transferred to the spent ore pile located approximately 1,000 meters to the northeast. The pile currently contains approximately 6 million tons of spent ore. The pile liner, which has been constructed over a prepared sub-grade consists of three geosynthetic layers (geotextile/flexible membrane liner/geotextile). Long term objectives include washing the pile to recover an additional 3 to 4 percent gold and silver.

Jan 1, 1993

By Todd Kilduff, Ryan O’Connell

Pipe canopies continue to gain momentum as a reliable methodology for construction of excavations below critical facilities with minimal surface settlement tolerances, such as railroads or roadways. Two tunnel projects designed by Kilduff Underground Engineering in the Salt Lake City, UT area, each at varying stages of completion, had project design criteria for selection of a tunneling methodology to minimize surface settlement. Both projects consist of a pedestrian tunnel, one crossing beneath a major roadway in downtown Salt Lake City and the second beneath UPRR tracks. Both projects were in difficult, coarse alluvium/fan ground conditions with project criteria that resulted in minimal cover above the tunnel. For each project, a pre-support pipe canopy was designed, requiring the placement of steel, canopy pipes driven the extent of the tunnel length. The pipe canopy is installed using a trenchless technology and then excavated with SEM tunneling and shoring provided by traditional support of excavation methods. The pipe canopy pre-support method offers a low-impact method to install an underpass beneath critical structures by adding significant stiffness to the subgrade to mitigate surface settlement during the main tunnel excavation sequence. These case studies seek to communicate the challenges associated with pipe canopy installation in site-specific ground conditions and explains how these challenges were overcome. This paper aims to define the project risks and describes the pipe canopy methodology as a viable solution to mitigate surface settlement in low cover tunneling scenarios.

Jun 13, 2023

By Y. H. Zhan

A new P(MAAA) latex was developed and used in separation of ultrafine apatite from calcite and silica by means of selective flocculation. The latex was found to flocculate selectively apatite from apatite/calcite and apatite/silica mixtures in the presence of sodium tripolyphosphate and sodium silicate over a pH range from 9.1 to 9.4. The separation of apatite from calcite was more selective with sodium tripolyphosphate, while the results of the separation of apatite from silica were better when sodium silicate was used. In the apatite/calcite system, 90% apatite recoveries into a concentrate containing 34% P2O5 were possible in the presence of 4 mg/l of sodium tripolyphosphate at a latex dosage of 2.2 kg/t. In the apatite/silica system, 80% of apatite could be recovered into a concentrate containing 33% P2O5 in the presence of 20 mg/l of sodium silicate at a latex dosage of 1.1 kg/t. Deposition tests were used to study the interaction between the latex and the mineral surfaces. The results revealed that deposition density of the latex on apatite was higher than on calcite; the differences between the deposition onto these two minerals were higher at pH 9.2 than at 7.2. The results point to the stronger interaction between the latex and apatite surface when compared with the latex-calcite interactions.

Jan 1, 1998

By G. S. S. Raman, M. S. Klima

Coal refuse slurries stored in tailings impoundments can potentially lead to environmental concerns such as effluent seepage, property devaluation, and in extreme cases, dam failures. Pressure filtration offers an opportunity to reduce the impoundment requirements by providing significantly drier solids. A full-factorial design was used to study the effects of temperature and pH on dewatering a refuse slurry obtained from a coal preparation facility in Pennsylvania, USA. The experimental results indicated a strong effect of temperature on cake moisture as the cake moisture after about 2800 s was 22% at 43 °C and only 36% at 10 °C for tests conducted at pH 3. ANOVA results confirmed the statistical significance of pH, temperature, and their interaction effect. Also, the results showed no significant differences between the tests conducted near neutral and alkaline pH values at low and ambient temperatures. On the other hand, Tukey’s test indicated higher reductions in cake moisture at higher temperatures for lower pH values. This study affirms the need to monitor and control the pressure filtration process as throughput could significantly vary with changes in temperature and slurry conditions.