Search Documents

By K. M. Kolin

ABSTRACT OF ORAL PRESENTATION A discussion of current U. S. Bureau of Mines research into the problem of strata control in multiple Western coal seams will be presented. The problem and research priorities will be described as determined from interviews with major Colorado and Utah mine operators as well as governmental agencies responsible for Federal leases. Proposed contract research and ongoing in-house studies will be discussed, including case histories and results from projects being conducted at two multiple seam operations in Utah.

Jan 1, 1977

By Jinke Li, Fenghua Wang

"While coal fueling China's economic growth it has already been causing severe pollution and amounts of CO2 emission. How to make deep reductions in carbon emission is not only a huge challenge for the greatest consumer of coal, but also a revolution for China’s coal industry. The paper explores how to shrink CO2 emissions during the lifetime of coal. The paper points out that increase of coal mine efficiency and productivity, green mining, utilization of coal mine methane and environment-friendly disposal of coal gangue can reduce CO2 during coal mining; coal preparation and coal by wire can decrease CO2 during coal preparation and transportation; improving combustion efficiency, CO2 capture and storage (CCS) and coal transformation can lessen CO2 during coal utilization. The paper also points out that Circular Economy Park is a practical way to develop a low carbon economy for coal industry. An econometric model for total coal industry and each sector are constructed to measure carbon emissions based on CO2 equivalent emissions, then with detailed calculations, based on potential greenhouse-gas emission's reduction, a most likely low carbon roadmap of China's coal industry is depicted with scenario analysis method.Introduction Global warming poses a profound threat to humanity and the natural world and is one of the most serious challenges humankind has ever faced. According to the 2007 Fourth Assessment Report by the Intergovernmental Panel on Climate Change (IPCC), global surface temperature increased 273.89 ± 273.33K during the 20th century (IPCC 2007). Increasing concentrations of greenhouse gases have caused most of the observed temperature increase since the middle of the 20th century (United States National Academy of Sciences 2008), and CO2 is the most important cause of global warming. In 2005, CO2 contributed 76% of global greenhouse gas emissions, CH4 contributed approximately 16%, N2O contributed approximately 6% and the combined F-gases contributed approximately 2% (IEA 2010). Among the many human activities that produce greenhouse gases, energy use is by far the largest source of emissions. Since 1870, CO2 emissions from fuel combustion have risen exponentially (IEA 2009). Of the three types of fossil fuels - coal, natural gas and petroleum - coal constituted only a quarter of the world total primary energy consumption in 2007. The situation is even more critical in China than in the rest of the world, as energy-intensive industrial production is growing rapidly, and large coal reserves exist in combination with limited reserves of other energy sources. The development and production of the coal industry provide stability in China's economic growth. There are more than 7000 coal enterprises in China; the coal enterprises are the main contributor to China's ""economic miracle""."

Jan 1, 2017

By V. Arad, S. Arad

Besides the conservation and closing activities, an important issue to achieve is the environmental rehabilitation of the mining perimeters, also assuring the continuity and sustainable development of the mining activity in the Jiu Valley. Modifying and depleting the soils by mining works and dumps of mineral waste as a result of coal mining and tailing is one of the important aspects. The paper’s aim is to analyze which are minerals and resources policies of our government and to adopt measures for sustainable development in the coal mining in this region. The measures to reduce the instability risk for the mining works and waste dumps, which could affect the underground mining constructions or the related surface areas, were consider. It is most important to establish the priorities in order to obtain a high efficiency by combining the measures according to the environmental analysis and risk assessment.

Jan 1, 2005

By P. Roghanchi

The difficulties associated with performing direct tensile strength test lead to development of indirect test methods, which are simple, less expensive, and less time consuming. Splitting tensile strength test (Brazilian test) is performed by applying two opposite concentrated compression load across the diameter of a disk specimen until the failure occurs along the loaded diameter. Theoretically, the load is applied over a small width as a line load, however, by increasing the load, the contact width between the loading jaw and the specimen increases as the specimen deforms. The main aim of this study is to investigate the stress distribution in (1) regular Brazilian specimen in traditional tests with loading jaws and (2) flattened Brazilian specimen with flat platens. A series of the splitting tensile strength tests and uniaxial compression strength tests are performed on three rock types: rhyolite, basalt, and limestone. Further, Numerical modeling studies are performed to investigate the effect of the contact between jaw and Brazilian specimen on stress distribution in the disc specimen based on the results from the experimentation. Finally, the stress distribution in the traditional Brazilian test specimen and the flattened end Brazilian test specimen were compared.

Feb 23, 2014

By J. T. YIi-Penttiia

Dust formation and reaction mechanisms of copper matte particles were investigated in simulated flash oxidation conditions. The granulated and ground matte consisted of 72 wt% Cu, 4 wt% Fe and 21 wt% S. Experiments were conducted by using a laminar-flow furnace with a reaction gas composition ranging from 20 vol% to 75 vol% O2 in nitrogen. The particle feeding was carried out by the single-particle method and samples were quenched after a specified reaction time (approximately 0.05-004 s) in a cold water film. Experimental temperatures were between 800 and 1300°C. Chemical analysis was used to determine oxidation degree, and an optical and scanning electron microscope combined with energy dispersive analysis was used for characterization of the reacted particles.

Jan 1, 1998

By James R. Oehler

Progress, future challenges, and the continual search for more efficient and rapid methods of excavating underground openings and shafts were main themes at the 1983 Rapid Excavation and Tunneling Conference (RETC) held June 12-16 in Chicago, IL. The event, jointly sponsored by the Society of Mining Engineers, the American Society of Civil Engineers, the Canadian Institute of Mining and Metallurgy, and the Engineering Institute of Canada, offered a diverse program for both civil and mining engineering disciplines. Although all papers given at the three-day conference were noteworthy contributions, and each is included in the conference proceedings currently available from SME, there were a few sessions that had particular mining-related interest. Research, Acceptance Needed for Water-Jet Technology Water-jet-assisted rock excavation is seen by some as a technology moving from the prototype phase to a fully developed, accepted system within the next decade. For an industry that is traditionally fairly slow in accepting significant changes, this development appears especially noteworthy. However, speakers at the water-jet technology session generally agreed that many large US manufacturers are not viewing water-jet-assisted equipment as viable replacements for all-mechanical systems. This, they fear, may mean some US manufacturers will lose a significant share of certain equipment markets to foreign competitors who are moving aggressively ahead in this area. Despite the advantages of increased cutting rates, reduced power requirements, less dust, prolonged bit life, and reduced sparking in many cutting situations, water-jet technology applied to mining is apparently having some acceptance problems in the US. R. J. Evans, professor of industrial engineering at the University of Pittsburgh, noted that there are several perceptual barriers to water-jet coal cutting; such as uncertainties concerning the fu¬ture demand for coal and the reliability of equipment, apprehensions that jet-assisted equipment will make the mine operator dependent on specific types of hard-to-obtain equipment, and fears about accessibility of the equipment for repairs. Evans also said numerous parameters need defining before taking advantage of water-jet-assisted cutting systems in under-ground coal mining in the US. For the cutting head, information must be obtained on optimum bit geometry and spacing, and maximum and minimum torque requirements. For a complete US water-jet cutting system, Evans added, research is needed to establish optimum jet pressures, jet powers, number of jets per bit, and location of jets relative to the bit. One research project making progress towards optimizing parameters for a water-jet-assisted drag bit cutting system for coal mining was described by Levant Ozdemir, director of the Earth Me- .

Jan 8, 1983

By E. J. Rogans, W. N. Cartner

Carbon technology has largely superseded filtration plants as the more acceptable gold recovery technology. This has, over the last two decades, provided a tremendous driving force for the development of new equipment. One of the main focus areas of this technological development is the development of effi­cient interstage screening systems. Several variations of exter­nal and internal screens are available, with the more recent shift away from air cleaned units to mechanically swept units. This paper discusses the development of one such mechanically swept interstage screen and how the development led to the suc­cessful implementation of a carousel type of CIP operation. The first generation Pump-cell emerged as a consequence of the success achieved with the mechanically swept NKM screen, The idea was to modify the screen to incorporate the functions of pumping, screening and agitation in a single drive unit, the screen generating sufficient lift for interstage slurry flow so that all contactors would be at the same level. This sys­tem was further incorporated as a high intensity modular CIP contactor, i.e. low slurry residence times combined with high carbon concentrations. A discussion on the kinetic gold adsorp­tion theory and its manipulation in the design of the pump-cell concept is discussed in a paper published in a previous Randol Conference< 1), Testwork carried out at Vaal Reefs proved the concept of the Pump-cell on a pilot plant scale<2), which resulted in the building in 1990 of the first large Pump-cell plant at West Witwatersrand Gold Mine designed to treat 340m3 of pulp per hour and , even though the plant operated successfully with respect to gold recovery performance, a few problems were experienced with the basic engineering design(3),

Jan 1, 1996

By Roy Norcross

For the past few years Caro's acid has been used for the treatment of cyanide containing slurry effluents, providing a feasible alter­ naive to other slurry treatment processes including !NCO SO2 / Arr and ferrous sulfate. Presently, mines using Caro's acid gen­erate their own Caro's acid onsite making a relatively low quali­ty product. It was at this point where we, at Degussa Corporation, decided to focus our efforts on engineering a Caro's acid genera­tor capable of cost effectively producing a high quality Caro's acid solution, thus reducing operating costs significantly. Caro's acid or peroxymonosulfuric acid is not a new chem­ical nor is it new to Degussa. The product was named after Heinrich Caro (1834-1910), a German chemist who first described its synthesis and its oxidizing properties in 1898. Degussa has been producing the potassium salt of Caro's acid as the triple salt, 2KHSO5 - 2KHSO4 - K2SO4, called Caroat®, for over 30 years. Caroat® is used for household and denture cleansers, as a bleaching agent in dish washing detergents, in printed circuit board etching and for cyanide destruction in the plating industry. From our experience in producing Caroat® Degussa developed its new Caro's acid based DegOX™ technology for the treat­ment of cyanide containing effluents from gold and silver mines.

Jan 1, 1996

By R. Hemp

This paper describes work carried out to obtain a heat balance in the B3 shaft longwall stope at Blyvooruitzicht gold mine. Recordings were made of the temperature of the air and chilled water entering and leaving the section during three periods, August 1 September 1977, November 1 December 1977 and March 1978. These recordings, together with numerous other measurements were used to determine the rate at which heat was being removed from the section by the various fluids flowing through the section. The rate at which heat was entering the section was then calculated, by considering each source in turn. These two sets of figures made it possible to draw up a heat balance, and also obviously gave vital information on the magnitudes of the various heat sources and on the methods used to remove heat. In general reasonable heat balances were obtained, the errors being in the range -6 per cent to +22 per cent.

Jan 1, 1980

By Bruce Johnson

This paper is not written to "break new ground" in computer applications; it is just a treatment of how an operating metal mine utilizes a mainframe computer for planning, analyzing, and reporting on the ventilation and cooling systems. The Unisys mainframe computer at the mine site is used in programs that analyze the ventilation network, keep records on various ventilation installations, calculate the results of measurements and produce reports on ventilation conditions in the working places and on the main air distribution, and plan and analyze the cooling system. All the programs are interactive to terminals. There are a series of data files that are generated by some programs which may be used by other programs. Most of these programs have been developed in-house. The computer is also used as a word processor via a vendor-supplied text editing program to produce memos, letters, and to keep up-to-date lists of equipment used.

Jan 1, 1989

By Robert F. Hauck

This chapter discusses a new technology for computer control in open-pit mine operations: the real time automatic dispatching of manually driven trucks to shovels. The monitoring of truck activity is accomplished by detection of local radio signals. Computer-operated directives are communicated to drivers by remote controlled digital display units inside the truck cab. The production objective is to maximize tonnage in a cost effective manner. The problem is formulated in the appendix and the solution method is briefly described. Side conditions such as maintaining delivered ore grade aims, balancing waste to ore volumes to keep within stripping ratio tolerances, and meeting production rate requirements temporarily established for certain shovels are also discussed. Experience with a developed event- to-event simulator applied to analyses of several North American mining operations using this technique is summarized. Complete systems employing this technology are now under- going installation at mine sites in Canada and the United States.

Jan 1, 1979

By D. W. Park

Underground openings resulting from coal mining activities have been a serious cause of subsidence problems in the Warrior coalfield of Alabama, which is the 11th largest coal-producing state in the United States (National Coal Association, 1986). The problem will be even more serious in the future because 17 Gt (19 billion st) of Alabama&apos;s 22 Gt (24 billion st) of coal reserves are classified as an under- ground resource (Tolson et al., 1982). Subsidence data in this area has been scarce com- pared with other coalfields (Conroy, 1980; Dunrud and Osterwald, 1980; Gentry and Able, 1978; Hunt, 1979; King and Gentry, 1979). This paper discusses the results of a study of subsidence overlying two longwall mines that contrast each other. One of them (Mine #1) is a shallow longwall mine where the coal strength is very high, and the other mine (Mine #2) is extremely deep with a low strength of coal.

Jan 1, 1987

By Jindrich Fiala, Jirí Kout

The paper contains knowledge that have been achieved when the problem of airflow temperature and humidity changes prediction in mine airways was investigated. The substance of physical processes has been consistently applied. The methods of dry-bulb and wet-bulb temperatures calculations can be applied in any type of mine airway. The exceptionality of auxiliary ventilated airways is in the original solution of so called losing air flowing when a ventilation pipe is leaky. The combination of aerodynamics and thermodynamics solutions enable to determine climatic conditions on projected workplaces with a sufficient accuracy.

Jan 1, 1991

By J. A. Burger

Research in the eastern U.S. has shown that productive mine soils and forests can be restored using the following guidelines: (1) cooperation among the mine operator, landowner, and regulatory authority in developing the mining permit; (2) replacing topsoil or creating a desirable medium in which trees are planted; (3) loosely grading non-compacted topsoil; (4) using native and non-competitive domestic ground covers that quickly protect the site; and (5) planting a proper silvicultural mix of crop trees for their commercial value along with nurse trees for wildlife and soil improvement.

Jan 1, 2002

By E. Forssberg, Y. Zeng

Fine crushing and rod grinding have been investigated using a laboratory-scale jaw crusher and a rod mill. The net energy consumption in both crushing and grinding was evaluated from torque measurements. An empirical relationship was established between energy consumption, particle size and operating parameters. When the mill feed size is reduced, through fine crushing, to about 80% passing 3 mm, the energy consumption will be minimized in a comminution chain of fine crushing and coarse rod grinding. The results in fine crushing were compared with a large-scale test.

Jan 1, 1993

By A. J. Neale, B. C. Flintoff

A relatively inexpensive and reliable method of using liquid phase tracers to aid in the solution of material balance problems is introduced. The method is of value in situations where one is required to calculate a material balance around a process that has the operating appearance of a "blender" or "splitter" with respect to the available slurry sample data. The paper briefly reviews material balance development and tracer applications in mineral processing, introduces the problem to he addressed, and provides both theoretical and industrial evidence establishing the potential of the method.

Jan 1, 1987

By W. C. Smith

Even with the most conservative mine plan, rib instability can occur unexpectedly, and if not adequately dealt with, can progress from a nuisance to a major safety hazard. This Bureau of Mines paper examines the mechanisms of progressive rib failure in high mine openings and discusses techniques to control rib slabbing. A field test site in a longwall mine was instrumented to investigate rib behavior during mining. While data analysis showed minor pillar dilation, sporadic zones of progressive rib instability were detected which culminated in eventual rib failure. The failure occurred despite conservative pillar dimensions and shallow depth. Physical and computer models were used to demonstrate the mechanisms of rib failure and then evaluate the influence of support and other mine-related parameters on rib behavior.

Jan 1, 1989

By L. C. Bartel

Geologic features such as structure (faults, folds, fractures, etc.), water bearing zones, aquifers, pemeability variations, and porosity variations are important for mine planning and in situ energy recovery processes. Features important for planning a mine will be important for planning the recovery of energy by in situ processes. Various geophysical techniques might be used to obtain the necessary geologic information. In this paper, case histories will be discussed of the use of electromagnetic geophysical surveys at a potential underground coal gasification site and a potential tar sand oil recovery site to obtain pertinent geologic information. Results show that the controlled source audio- frequency magnetotelluric technique shows promise for mapping faults and natural fracture systems when there is a sufficient resistivity contrast.

Jan 1, 1982

By Robert A. Metz

During the past decade we have witnessed spectacular improvements in productivity of open pit mining equipment. Thousand-horsepower engines, 200-ton trucks and 15-yard electric shovels, which such a short time ago were just dreams on a drawing board, are now realities. More productive equipment and metal shortages have encouraged increased production at existing mines and the development of new larger tonnage operations. Operators and engineers have been able to employ computers and various other types of automation to "stay on top of things". The mine geologist, however, is merely faced with a bigger and more rapidly changing pit to pick in. Keeping geologic information current in these mines presents entirely new problems to mine geological staffs. To obtain adequate geologic information on the developing orebody requires enlargement of the staff to share the work load or revision of methods in keeping with the times. The former has the disadvantage of loss of the comprehensive knowledge of the pit that a chief geologist likes to have, not to mention management&apos;s usual lack of enthusiasm for force increases.

Jan 1, 1970

By Alfred Opengart

During any rush hour, tens of thousands of automobiles clog the main highways leading into or out of our large cities. Inevitably one or more cars stall or plow into another, causing a momentous traffic jam. Traffic backs up for miles as drivers try to maneuver around the roadblock. As commuters, we grin and bear the inconvenience, rationalizing the delay as part of the price one pays to live in a modern society. The truth of the matter is that the engineers planning the roads have the know-how to build adequate bypass alternatives into their design. The problem is one of economics -- can the cost of eliminating roadblocks be justified? Engineers designing solutions to complex materials handling problems for modem distribution centers are just now beginning to ask this question in relation to their work. Unfortunately in many instances, it has taken an expensive "traffic jam" to bring this question to the front. In these cases, a seemingly practical system promising an attractive return on investment -- using the latest equipment and computer controls -- was designed and installed. Everything went according to plan until one day a breakdown occurred. .Product flow stopped, and management realized it was at the mercy of the "machine." In such situations, management had assumed it could minimize the risks of the breakdown by injecting extra manpower to operate the system manually and pay the associated costs. What it had not recognized is that manual intervention is nearly impossible with sophisticated systems. Thus, too often -- and sometimes too late -- management found itself footing a very high bill for losses incurred because of major production stoppages and missed customer shipments.

Jan 1, 1973