Search Documents

By Thomas L. Mell

Continuous processing plants handling liquids have achieved a high degree of centralized automatic control. Many chemical plants are operated from one room, with automatic control of the various process flow rates. These plants know from experience that automatic control can produce higher through-put, better uniformity of product, decreased operating costs and reduction of storage capacity, Plants which process materials in the form of bulk solids have not been able to use control to as great an extent, primarily due to the lack of measuring equipment capable of providing the same types of continuous automatic control available with liquid flow meters. This paper will describe a scale for measuring flows of bulk materials on conveyor belts which is particularly adaptable to remote centralized instrumentation and automatic control, and will also describe some typical control applications. Fig. 1 illustrates the basic method of measurement of this scale. A conveyor belt idler is supported on a rigid carriage which in turn is mounted in two anti- friction bearings on the conveyor stringers. The pivoted carriage is prevented from rotating about the pivot shaft by an electric strain gauge load cell connected between the carriage and a cross support. Increasing load on the conveyor belt increases the moment of the carriage frame about the pivot shaft, and proportionally increases the tension in the load cell. The belt speed is measured by a conventional d. c. tachometer generator driven from a pulley, usually on the return belt. The speed signal from the tachometer generator and the load signal from the load cell are combined to produce a signal proportional to the flow rate of material in tons per hour, or lbs. per foot, or equivalent units, It will be important to remember, in considering various control applications, that the flow rate of material on the belt is composed of these two component signals, namely the weight of material and the speed at which it is moving. The feed rate is then indicated and recorded by a self-balancing potentiometer of the type used for measuring temperature by means of thermocouples. These instruments may also be equipped with integrating mechanisms reading the totalized tonnage over a period of time.

Jan 1, 1958

By Armando M. Lago

This paper reviews the postwar changes that have occurred in the expenditure and financial behavior of mineral corporations, and in particular the relative importance of factors that affect the industry's supply and demand for funds. This quantitative statistical investigation of factors affecting sources and uses of funds of mineral corporations is achieved through the formulation of a simultaneous equation model of sources and uses of funds. After a description of the study sample in Section I, the postwar cyclical and secular financial behavior of mineral corporations is analyzed in detail in Section II. Section III formulates an econometric model of mineral corporate financial behavior which is then estimated and reviewed in Section IV. Section V discusses policy issues regarding depletion allowances, investment tax credits, and industrial organization of the mineral sector. Finally, the optimum financial structure of mining firms is discussed in Section VI, which analyzes the effect of corporate financial structure on the mining corporations' average Cost of capital.

Jan 1, 1969

By C. Asgaard

Asset availability has been a longstanding objective in mining and mineral processing plants around the world. Enormous resources in both dollars and manpower are invested in improvement efforts to achieve higher asset availability. One dimension of asset availability is the time equipment is out of service for large scale planned maintenance activity: grinding mills, kilns, furnaces, mobile equipment, shovels and draglines are all regularly taken out of service for extended repairs and service. The speed, cost and quality of these planned outages provide an opportunity to increase asset availability. Equipment shutdowns are projects that are executed in a compressed time period. This paper will describe how the overall time and cost of equipment shutdowns were significantly reduced at Cliffs Natural Resources Michigan Operations (CNRMO) through the introduction of the Critical Chain Project Management techniques.

Jan 1, 2009

By O. Schumacher

Guidelines for publication of information defining the amount and grade of resource material available in a deposit are well established in Australasia?s JORC Guidelines, Canada?s National Instrument 43-101 and similar documents in South Africa, Peru, Chile and elsewhere (Table 1). These guidelines provide standards to apply regarding the geologic and geostatistical basis for describing the level of confidence to be assumed for an estimate of the amount and grade of material. All of them provide for a strict distinction between material that has been demonstrated to be economically mineable and that which has not, and all of them provide terms such as ?resource? or ?exploration information? to be applied to data regarding material that has not been demonstrated to be economically mineable. It is not until an economic study has been completed that we are allowed to apply the powerful terms ?reserves? and ?ore? to our deposit material. Indeed, the application of these eye-catching labels immediately tells the reader that an economic study has been completed by a qualified person, and that the results of the study were positive. While extensive guidelines are established for describing the level of confidence in published geologic data, and the nature of the economic study that should be accomplished before using the terms ?reserves? or ?ore?, surprisingly little guidance is provided regarding the process to use, and the level of detail to attain, for estimating capital and operating costs for the study. The intent of this paper is to lay the groundwork for development of suitable guidelines for the cost estimating process. While the codes do not provide specific instructions for the cost estimate, they do provide numerous hints and clues to help determine the level of detail expected and the type of procedure to apply in preparing the estimate. This paper will first review the various codes to gain an insight into the thinking of the drafters of the codes regarding their unstated expectations for the cost estimating process. Based on this review, a series of guidelines are proposed for this purpose.

Feb 27, 2013

By Frederick J. Hoppe

The productivity or usefulness of a Front End Loader rises rapidly with its size. Loading is more aggressive. Mother Nature is defeated more easily. Larger tires get a better grip on the ground. Hauling equipment can be loaded more quickly. The productivity or usefulness of a Front End Loader is proportional to its working speed, both automotive and hydraulic. The price of speed is horsepower, which rises rapidly with speed. Horsepower saved shows up as increased productivity. This paper covers the development of the D600, KW-Dart's articulated loader, which combines massive size with new concepts to increase its working speed. Featured is a discussion of the horsepower saving, "Balanced Boom."

Jan 1, 1969

By Richard Gertsch, Jack Eloranta, Leslie Gertsch

An ongoing research program is characterizing the ore qualities that most affect mine and mill processing of iron. Current practice uses assays of magnetic iron and silica, but additional qualities are needed for advanced process control. If additional qualities can be measured from core, blastholes, or process samples, they can be modeled and controlled similarly. What qualities, other than assays, hinder or facilitate beneficiation at each processing step, and how can they be measured in the mine/mill ore stream? This paper describes preliminary determinations of the effects of ore chemistry, hardness, blasthole drill performance, fragmentation control, and grindability on mill performance.

Jan 1, 2005

By Keith G. Wallace, K. M. (Chris) Chmura, Kirk H. McDaniel

The Waste Isolation Pilot Plant (WIPP) performed a feasibility analysis for the purpose of either modifying, supplementing, or replacing its two main mine fans. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) fa¬cility designed to demonstrate the permanent, safe disposal of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Since the centrifugal fans were installed in 1988, multiple op¬erational and performance concerns have been identified. A com¬prehensive engineering study was conducted in 1995 to: 1) Qualify and quantify operational concerns, 2) Evaluate possible alternatives, and 3) Recommend an optimum solution. Multiple system modification and/or replacement scenarios were evaluated with associated cost estimates developed. The study considered replacement with either centrifugal or axial fans. Multiple fan duties are required at the WIPP. Therefore, Variable Frequency Drives and Inlet Vane Controls (IVC) were investigated for centrifugal fans. In-flight adjustable blades were investigated for axial fans. The study indicated that replacing the existing system with two double-width, double-inlet centrifugal fans equipped with IVCs was the best choice. This alternative provided the most desirable combination of: 1) ensuring the required operational readiness, and 2) improving system performance. The WIPP is currently planning to replace the first fan in 1997.

Jan 1, 1997

By Peter Zhang, I. BERK TULU, Morgan M. Sears, Heather Dougherty, Ted Klemetti, DYKE MARK VAN, Gabriel S. Esterhuizen

Ground falls in longwall gateroad entries remain a concern in modern longwall operations. The gateroads are subject to changing horizontal and vertical ground stress induced by longwall extraction. These stress changes can result in failure of the strata around an entry leading to large deformations of the entry roof, floor and ribs. The gateroad support systems are required to control the failed strata while maintaining safe access to the longwall face and unimpeded ventilation. This paper presents research conducted to better understand the stability issues in gateroad excavations and to develop procedures for evaluating support and layout alternatives for longwall gateroads. Using the results of a field-monitoring program and numerical model analysis of case histories, a conceptual model of gateroad support needs was developed. The conceptual model formed the basis for developing a set of equations that can be used to estimate likely roof sag and support loading for given roof geology and longwall-induced loading conditions. The developed equations were used to compare predicted gateroad stability to field study results, showing satisfactory agreement. The calculation procedures are used to demonstrate their application in assessing support alternatives at a case study mine. It is concluded that the developed analysis procedures provide realistic assessments of likely ground stability and can be used to evaluate alternative gateroad support systems at operating longwall mines.

By Mary E. Learmont

Grinding with steel media adversely affects the flotation response of galena. Electrochemical measurements, flotation tests, and AES, XPS, and STEM examinations were employed to identify interactions between galena and mild steel. Iron oxide, hydroxide, or sulfate species that formed on the galena surface upon contact with mild steel decreased its floatability, with the time of contact and aeration condition affecting the severity of the flotation depression.. Parallel tests performed with an active metal, magnesium, indicated that floatability was also affected by the presence of a surface coating involving lead species.

Jan 1, 1984

By Patti J. Best

The Southern Powder River Basin (SPRB) now commands 30% of the US utility, coal market due to the region's low mine production costs, competitive rail rates and low sulfur content. In 1997, production exceeded 240 Mt (265 million st). This was an in¬crease of 104 Mt (115 million st) since 1989 and 4.5 Mt (5 million st) above 1996. Continued growth is expected as the second phase of the Clean Air Act Amendments (CAAA) approaches. This growth will be the greatest in the southern part of the Basin where coal quality is higher. Coal characteristics SPRB coal is classified as subbituminous due to its low heating value and high moisture content. The coal is characterized by low sulfur and ash contents, low ash fusion temperatures and high reactivities. In 1997, the average heating content was 8,593 Btu/lb, with an average sulfur and ash content of 0.79 lbs S02/million [ ] Btu and 5.13%, respectively. The distinguishing characteristic of SPRB coal is its low sulfur content. Most SPRB coal contains less than 1.2 lbs S02/million Btu. This is the approximate definition of "compliance" coal for Phase II of the CA AA. Much of the coal, particularly in the southern part of the Basin, is referred to as "super-compliance" coal due to SO2 contents of between 0.4 and 0.7 lbs SO2/million Btu. The SPRB is divided into three geographic clusters based on coal quality. Mines located in the southern part produce coal with the lowest average sulfur content and highest heating content, almost 400

Jan 1, 1998

By D. A. Norrgran

The process of magnetic separation is based on the differences among magnetic susceptibilities of various mineral species. Performed either wet or dry, the separation has application in both the recovery and concentration of value minerals and in removing deleterious mineral constituents from a product stream. There are two major catagories to be considered when addressing magnetic separation of minerals. The first catagory refers to particle characterization and relative differences in magnetic susceptibility. The second catagory refers to design parameters and the magnetic field generated by the separator.

Jan 1, 1987

By P. D. Rao

Although phosphorus is a very important biogenic element, its concentration in coal is generally low. Phosphorus concentrations typically range from 0.001 % to 0.229% in raw coals of the contiguous 48 states. Some Alaskan coals in the Cook Inlet region contain horizons unusually high in phosphorus. A foot by foot analysis of deep drill core, containing 70 ft. of sub bituminous 'C' coal from the Beluga coal field, Alaska, showed certain increments contained as high as 17.03% P2O5 in the coal ash; 1.01 % P on a moisture-free coal basis. Crandallite has been identified by electron microprobe analyses as a phosphorus numeral in these coals. The authors could quantify calcium, barium, strontium and phosphorus concentrations from the coal attributable to crandallite. These high phosphorus coals provided a unique opportunity to study the association of phosphorus in coals using chemical fractionation for exchangeable cations and acid extractable elements. Since the source of high phosphorous horizons in Cook Inlet coals is attributed to volcanic ash, it is suggested that the profiles of acid extractable phosphorous concentration may be useful for coal seam correlations.

Jan 1, 1992

By P. O. Lindahl

The U.S. Bureau of Mines initiated research to improve the safety and efficiency of transporting coal from deep underground mines using a balanced air-lift hydrohoist. A 50-m-high pilot-scale model was constructed and tested to evaluate the feasibility of hydraulically hoisting a coal-water slurry in a U-tube pipeline from the mine level to the surface with the assistance of compressed air. A prototype screw feeder is used to continuously compact and inject 5-cm or less run-of-mine coal into a pressurized 20-cm-diam pipeline. Production rates up to 40 metric tph at an airflow of 1.5 m3/min were achieved with the model, and coal size degradation was relatively minor. Modifications are in progress to achieve 100 tph at an airflow of 2.8 standard m3/min injected into the riser pipe. Pilot-scale results indicate that an air-lift hydrohoist system is a feasible, cost-effective alternative to conventional skip hoisting that can be installed in existing shafts or surface-drilled holes closer to the face area. Air-lift hydrohoisting offers advantages of infinitely adjustable slurry flow rates, reduced pressure at the point of coal injection, and flexible design that can be combined with hydraulic pumping. Proposed design changes are discussed for coal transport, mine layouts, ventilation, fire control, and escapeways using this system.

Jan 1, 1995

By Richard R. Klimpel

The first part of this two-part article summarizes the result of a 10-year, multimillion dollar research and plant testing program involving operating mining companies throughout the world. The program was aimed at developing a better understanding of the influence of slurry rheology on the performance of mineral/coal grinding circuits. Part 1 presents the basic concepts identified, including typical laboratory results showing the influence on grinding behavior of controlled changes in percent solids, particle size, slurry temperature, and viscosity control chemicals. Part 2, in January, will illustrate typical industrial scale test results on both open and closed circuits using the concepts presented in Part 1. Special emphasis will be placed on identifying some industrial operating implications of controlling rheology by different methods. Introduction The industrial-scale practice of wet grinding minerals and coals in tumbling media mills (ball, rod, and pebble) is well-known to operating mineral processing engineers and plant design personnel. Over the last century, considerable experience and data has been collected, correlated, and put into rules or guidelines for successful circuit design and operation. Typical factors influencing circuit throughput that have been analyzed in some depth are mill diameter and length, grinding media size and loading, feed and product particle size, mill power use, and the interaction of classifier type and efficiency with the grinding device. Until recently, knowledge of slurry rheology influence on large scale grinding circuit performance has been limited. Even today slurry rheology effects are essentially ignored in plant design. Indeed, in most plant operations only qualitative guidelines are followed. For example, too thick a slurry causes throughput losses and too thin a slurry uses excessive water or causes water handling problems such as pumping limitations. A search of published literature and numerous discussions with experienced plant operating personnel has shown an awareness that changing the percent of solids in the mill influences grinding or the response of grinding involving fine feeds versus coarse feeds. However, most the work identified relative to rheology effects in mineral/coal grinding was qualitative. Even in the few studies that were more quantitative, the scope of the work was usually too narrow to draw general conclusions. Also, the detailed rheological characterization tied to observed breakage and the combination of laboratory to industrial-scale testing that is required to develop a broad understanding of any factor influencing grinding had not been done. In this environment, this detailed program began in 1967. It had three distinct goals: • To develop a basic understanding of slurry rheology influence on breakage characteristics in the laboratory. • To test general rheology concepts developed in the lab on the industrial scale. • To develop a commercially viable chemical approach to controlling slurry rheology that would lead to the use of chemical grinding additives or grinding aids. The goals have been met, at least in part, this year. A small fraction of the extensive laboratory and plant results have been made available in published literature. Much of the research program dealt with identifying and developing chemical grinding aids, but a lot of useful and practical information on percent solids, particle size, and slurry temperature influence on grinding circuit performance also was collected. The purpose of this article is to present a clear and concise sum¬mary of the results of the entire program. The importance of rhe¬ology control in grinding circuit behavior will be demonstrated using a series of carefully per¬formed industrial scale experi¬ments (both open and closed cir¬cuits) that have not yet been reported in general literature. Mining companies participating in the test program on a proprie¬tary basis have found the informa¬tion in this article to be useful in better understanding and improv¬ing circuit performance. Viscosity Effects in Grinding Studies In this program&apos;s previous labo¬ratory studies, it was shown that there is a consistent pattern of change in specific rates of break¬age of both mineral and coal slur¬ries as slurry fluidity changes. Using the net production rate of material smaller than some spec¬ified size-for example, kg/hr of <75 µm (200 mesh)-as an index of mill production in a standard batch mill test (with a given feed material, feed size, mill, and mill conditions such as constant time of grind), the following facts were established (see Fig. 1): • The normal range of low den¬sity, low viscosity slurry (region A) gave no variation in mill produc¬tion. The measured rates of break¬age exhibited normal first order grinding. • Grinding of a somewhat higher viscosity slurry (region B) could give increased production. The higher viscosity was obtained

Oct 12, 1982

By C. A. Rowland

With the rapidly rising cost for electrical energy and the long range pre¬dictions for continued rising costs and even possible energy shortages, operation of rod, ball, autogenous and partial autogenous grinding circuits to efficiently utilize the power delivered to the mills will be demanded. This calls for a method to evaluate grinding circuit performance that is accurate, reliable and readily usable as an operating tool by supervisory, technical and operating personnel. Neither the Rittinger and Kick theories of comminution,(1) which preceded the Bond Theory by more than 50 years, had a mathematical means that could be used to predict and evaluate the performance of crushers and grinding mills used to comminute ores and rocks. This severly limited the practical use of these two theories, which were contradictory to each other. They have been superseded by the Bond Third Theory of Commnution.(1)

Jan 1, 1976

By Bo Hyun Kim, Mark K. Larson

Although techniques and practices of mining are highly advanced, coal pillar bursts or bumps continue to occur. Many uncertainties remain because of the highly anisotropic characteristics of coal seams that are associated with geologic structure and the mining-induced spatial redistribution of stress in coal pillars. Thus, to prevent fatalities in underground coal mining, continuous efforts are required to better understand the catastrophic failure mechanisms in coal mines. In this study, 3DEC modeling in conjunction with the Discrete Fracture Networks (DFNs) technique was performed to better understand the true anisotropic behavior of the specimens acquired from a bump-prone underground coal mine. The spatial characteristics of the dis- continuities (i.e., cleats and bedding planes) as input data for the 3DEC model are estimated based on the results of the laboratory tests and field observations. The DFNs explicitly generated the coal seam that was poorly or well cleated, indicating the different spacing between cleat apertures using the probability distribution functions for fracture density (or frequency) and size. The heterogeneity of the engineering properties (i.e., cohesion and tensile strength) are also considered by Monte Carlo simulations. Simulation results of laboratory tests using the 3DEC model and DFNs technique agreed well with the results of the laboratory tests. These calibrated results can be used as we seek to evaluate bump risk by modeling at field scale.

Jun 25, 2024

By Rick Sarkisian, Greg Girardey, David Keech

The Conveyor Equipment Manufacturers Association (CEMA) specification B105.1 "Welded Steel Conveyor Pulleys" adequately defines pulley assembly standards for light material handling applications. However, most mining applications demand pulleys of higher reliability and load capacity than that offered by CEMA standard pulleys. Various sources have published specifications for "Engineered" conveyor pulleys. Typically, these specifications require T-section type pulleys applicable to operating belt tensions exceeding 439 N/mm (2,500 lb./in.). This paper examines the application of CEMA standard pulleys, T-section pulleys and also a mining duty pulley design. The mining duty pulley fills the void between CEMA standard pulleys and T-section pulleys and can eliminate the high cost and long lead times associated with T-section type pulleys.

Jan 1, 1998

By David L. Durler

In-situ uranium mining is a relatively new and innovative method utilized for the commercial extraction of uranium. As with any mining method, however, significant environmental concerns will be evident and must be addressed in a rational and far-sighted manner. Experience has shown that radiological and non-radiological environmental problems may not manifest themselves until after the in-situ methodology has become established and matured to some degree. It is important, therefore, to recognize potential environmental concerns and incorporate them into an environmental program that spans the premining, mining, and post-mining phases of an in-situ operation.

Jan 1, 1982

By J. Herhold, S. Plaum

"Increasing worldwide energy demands, coupled with desires for cleaner energy, have led to greater research of renewable energies. Strongly weather-dependent energy sources, e.g. solar and wind energy, are unable to provide a constant control energy to withstand the fluctuation of the extensive power systems during peak hours. The pump storage plant Nant de Drance in Switzerland will not only have the capacity of a nuclear power plant, producing 900 MW, but will also combine the environmental aspect and the demand for controlled energy. Nant de Drance is one of the pioneer projects for upcoming energy challenges and serves as a model for future pump storage plants. This paper focuses on the planning process and the project execution of interdisciplinary large-scale projects such as Nant de Drance, including project related data handling, communication systems and project handling skills. Furthermore, the paper discusses mining excavation in the context of large scale projects and their regional environmental challenges, e.g. high alpine rock mass on the site of Nant de Drance. PROJECT BACKGROUND Project Overview Nant de Drance is a 900 MW pump storage plant located in the Swiss Alps. To provide such a high energy storage, six turbines (reversible Francis type), each with a capacity of 150 MW, were installed. Due to the efficiency factor of 80% the pump storage plant is able to provide an energy production of 2500 GWh per annum. Construction of the pump storage plant, which has been selected as “Major Tunneling Project of the Year” in 2014 by NCE and ITA-AITES, will be completed over 10 years. Therefore, the project has been divided in six major phases outlined below: - Launch: 2008 - Access Gallery: 2010 – 2012 - Excavation KMA, KTR: 2011 – 2014 - Concreting KMA, KTR: 2014 – 2016 - Installation of HEM equipment: 2014 – 2018 - Tests & entry into service: 2017 – 2018 Figure 1 outlines the single process phases of the project. For the construction of the shafts, galleries and caverns, 1.7 million m³ of metamorphic rock with sedimentary origin (mica schist & paragneiss of the massif „Aiguilles Rouges“) were excavated. A tunnel network with a total length of 15 km was created. The machine cavern measures 194 m long, 32 m wide and 52 m tall."

Jan 1, 2016

By Wenjun Ju, Xiaodong Sun, Jianwei Zheng, Bingding Yi, Zhaorui Ma, Pengfei Jiang, Lingfu Zhu, Yangfa Zheng

The presence of hard roof poses a significant threat to the safety of underground coal mining. In this study, a mechanical model is established for underground stopes to analyze the overburden structure with the advancing of the mining face. It is indicated that the load-bearing arch structure (LBAS) is formed above the stope for roofs with regular hardness, whereas the reversed-basin bearing structure (RBBS) is formed for hard roofs. Compared with the LBAS, the RBBS can induce an additional pressure at the foot of the bearing structure, and this effect becomes less as the distance between the hard roof and stope increases. The ultra-deep borehole hydro-fracturing technique (UHT) is proposed to weaken the hard roof for pressure release, and the associated equipment and procedures are also presented. The UHT is based on horizontal drilling along the axial direction of the roadway in the roof, and then the receding segmented hydraulic fracturing technique is used to achieve the purpose of fracturing (weakening) of the surrounding rocks. Field tests are carried out in 3022 roadway of Daliangwan coal mine in Yulin to assess the developed technique, equipment, and fracturing procedures. To evaluate the fracturing effect, deep borehole stress-meters are installed at different depths of the fractured and un-fractured zones of the roadway, along with hydraulic support pressure sensors placed at the mining face. The results show that compared with the un-fractured zone, the pressure on the wall and pillar sides is lower than that in the fractured zone, and the associated weighting duration and weighting area ratio of the fractured are reduced by 53.23% and 33.59%, respectively. This indicates that the presented UHT can provide a new solution for the prevention and control of mining disasters induced by hard roof failures in underground coal mining.

Nov 2, 2020