Search Documents

By R. D. Grove

The control of Florida phosphate flotation plants is largely based on the visual observations of experienced operators, both in recognizing good and bad froth conditions and in making judgments about the composition of feed, concentrate and tailing streams. Chemical analyses lag the process by at least two hours and therefore only assist in recalibrating the operators' vision when major deviations occur. An image analysis system has been developed by IMC Fertilizer to improve upon the accuracy and precision of the composition estimation process. It still relies upon the operator taking a representative sample, but provides a measurement in about 15 minutes after that sample is obtained. This paper describes the system and its use and presents comparative results for various process streams.

Jan 1, 1993

By Jose Agapito

Roofbolts with expansion anchors have been used at White Pine for more than twelve years, but always with an understanding that their performance was not entirely satisfactory. Some bolts fell out, some were obviously loose, and, when roof failures did occur, very few bolts actually broke. Obviously, there was an anchorage problem. A program was started in May, 1967, to define the problem and to solve it. This paper describes briefly those parts of the program which led to the development of a roofbolt assembly which performs much better in the medium-hard rocks at White Pine. As a result of the changes, significant improvements were found in the torque:tension, tension loss, and pull tests.

Jan 1, 1970

By G. J. Hodges

The Stillwater Mining Company, a partnership of Pittsburg & Midway Coal Mining Co. and Manville Corporation, operates a precious metals smelter at Columbus, Montana to further up-grade concentrates from its platinum/palladium mine. The smelter began operation in the summer of 1990. The gas cleaning system in the facility utilizes "oxidation/dilute mode" dual-alkali scrubbing technology to capture sulfur oxide gases from the process gas streams. This paper describes the rationale for selecting the dilute mode dual-alkali system and summarizes design parameters. Start-up problems and their solutions are also discussed.

Jan 1, 1992

By Shiou-Chuan Sun

Notwithstanding the fact that unsaturated fatty acids are used in preference to saturated acids for most flotation purposes, information regarding their collecting properties is sketchy. Keck, Eggleston, and Lowry1 reported in 1939 that the collecting power of fatty acids on hematite decreased in the order of oleic, lauric, myristic, palmitic, and caprylic acid. Keck and Jasberg2 described in the same year that "unsaturated oleic acid with 18 carbon atoms was a better collector than saturated stearic acid" for floating magnetite. Gaudin and Cole3 stated in 1953 that the double bonds of oleic and linoleic acid were not oxidized during the flotation of fluorite, whereas the double bonds of linolenic acid were measurably altered even after one single flotation step. In August, 1953, Hukki and Vartiainen4 concluded that the collecting power of palmitic, oleic, linoleic, and linolenic acids on ilmenite, magnetite, pyrite, and rutile increased with an increasing number of double bonds in the acid molecules. This was subsequently proved to be generally true for the flotation of mapganese5, phosphate6, and magnetite7. The above cited literature indicates that, prior to the present paper, only about ten minerals were tested with pure unsaturated fatty acids as collectors.

Jan 1, 1959

By H. Sevim

Three transportation and handling alternatives for delivering dry coal combustion residues from power plants to underground coal mines were evaluated technically and economically. The objective was to transport, handle, and inject the residues into the old workings of the mine at a minimum cost. This objective was accomplished in two steps: I) Simulation models were developed and utilized in identifying technically feasible designs in each alternative, 2) Technically feasible designs were economically evaluated to obtain the cost-per-ton of material transported. The designs that provided the minimum cost-per-ton were declared optimal An analysis was conducted for varying distances and tonnages to reveal favorable operating ranges of each alternative.

Jan 1, 1996

By Roy H. Paddon

This paper describes the 6, 000 tpd, three stage haulage system at the Ozark Lead Company's mine in southeastern Missouri. It details the methods and problems pertinent to the loading, hauling, sorting, crushing, storing and hoisting of waste rock and ores obtained from underground development headings and production areas. The Ozark Lead Company is a wholly owned subsidiary of the Kennecott Copper Corporation. Its mine is located nine miles south of Bunker in Reynolds County at the south end of the "New Lead Belt" mining district. Development started in May, 1964, by drilling a seven foot diameter (six foot cased), 1, 250 foot development-ventilation shaft. Drifting began in August, 1965, to obtain a bulk ore sample, to test ore continuity, and to drive two mine levels while the pre-grouted production shaft was being sunk. Over 7, 900 feet of 12 by 24 foot drifting was done from this small shaft. In March, 1966, a 20 foot diameter, three compartment, concrete lined production shaft was collared. It intersected existing development headings at a depth of 1, 195 feet in April, 1967, and was completed along with a concentrator and other facilities in June, 1968. Mine production began that month, with 5, 000 tpd reached in 1970.\

Jan 1, 1971

By A. P. Massmann

Design for economical operation, minimum operating labor and minimum maintenance for labor and supplies are virtually inseparable. Each consideration has a vital bearing on the other. Let us assume that we have the design complete for the most economical operation with a minimum of operating personnel. This means, in addition, that we have the fewest number of operating units consistent with the product requirements for a team or metallurgical coal which we are called on to produce. The number of units will vary greatly, being influenced by design, washability characteristics, tonnage and degree of quality control necessary by reason of producing a product for metallurgical, steam or domestic use. The units involved most ordinarily for any type coal preparation plant will number as a minimum the following: 1. Hoppering R.O.M. Coal 2. Feeding

Jan 1, 1959

By David T. Kao

The energy situation the world faced during the decade of the Seventies resulted in actions throughout the free world to reduce its dependence on OPEC oil. Many nations heeded the indicators early in that decade and commenced efforts to reduce their oil requirements. Those nations which did not heed these warnings had the message brought to them more emphatically in the last portion of the decade with the further rapid and continuing rise in prices of OPEC oil. Furthermore, the demonstrated unstable nature of large oil-producing countries has made it clear to all free world nations that their energy demands of the future must be provided for by some more stable and assured supply. Now, early in the decade of the Eighties, we see the need for expanded use of coal as an energy supply to be essential. The result in 1980 and 1981 has been a great increase in demand for steam coal worldwide. In essence, a new business for the United States has developed in steam coal export. In the United States, the large growth in foreign demand for our steam coal is now well recognized and documented. A major impediment in meeting this growing demand became abundantly clear in 1980. This impediment is the congestion existing at U.S. coal export ports. With the recognition of this constraint, a plethora of activity has been observed in announcements for alleviating the problem by improving and expanding current export port facilities. In addition to improvement and expansion, an abundance of totally new facilities has been announced in an effort to find ways to meet this large demand in the new business of steam coal export. This is needed; and hopefully, many of these plans will be translated into action. While total implementation of all stated plans is not expected, much of the implementation depends upon large- scale dredging, large waterside ground storage sites, and improved handling equipments in the conventional type of export ports. The time and capital required for implementation is great, and environmental problems associated with dredging are substantial. Host significantly, and unfortunately, implementation that does include dredging our ports will still not permit use of the truly large colliers of 140,000 DWT and greater, which are evolving as the "state of the art" in long-distance sea transport.

Jan 1, 1981

The segregation process has been known for many years and applied industrially for the treatment of various refractory copper ores. The principles of the process are briefly reviewed; the process was tested in the laboratory on two copper-cobalt oxide ores from Gecamines, Shaba Province, Zaire. Various parameters of the process, such as segregation temperature, dosage of reducing and chloridizing agents and flotation conditions were inyestigated. Experimental results have shown that the segregation of copper could proceed satisfactorily at low temperature (1000° K) but that of cobalt required higher temperature and higher additions of reducing and chloridizing agents.

Jan 1, 1992

By G. Deschênes

In an earlier study (Deschênes et al., 2009), gold and silver were shown to be efficiently extracted from samples taken from the Kupol Mine in Russia using lead nitrate in a cyanide leach system. In the current study, a com-parison of the technical and economic merits of a new technology called CANMET enhanced leaching process (CELP) was made with the cyanidation/acidification-volatilization-recycling (AVR) process using eight metal-lurgical variability samples, as well as a large composite sample, which was to represent the initial two years of Kupol mill feed. The composite sample leach feed assayed 33.4 g/t Au and 289 g/t Ag. The metallurgical results from the large composite sample demonstrated that CELP produced very similar gold and slightly higher silver leach extractions compared to the conventional cyanidation/AVR leach conditions at 1/2 the cyanide concentra-tion (1,000 ppm NaCN in CELP vs. 2,000 ppm for cyanidation/AVR leach conditions). It was estimated that the total cost per ton was approximately the same for the two technologies (total cost of CELP with the use of Merrill-Crowe at $46.48/t, with cyanidation/AVR at $46.13/t). However, the implementation of CELP would eliminate a capital expenditure of approximately $5 million for an AVR system based on a 2005 feasibility level cost estimate. Eight variability samples used to confirm the composite sample results showed that, on average, the gold leach extractions with CELP and the conventional leach conditions were very similar, but the average silver leach extraction was 2.1% higher for CELP. Furthermore, CELP silver leach extraction was 4.6% higher on average compared to conventional cyanidation for the four mid-grade variability samples evaluated. The decision was made to remove AVR cyanide recovery from the flowsheet and implement CELP at Kupol. The ability to use the conventional leach equipment with CELP and simplify the flowsheet was also a factor, given the remote location of the Kupol Mine.

Jan 1, 2010

By W. K. Katoto

The Tailings Leach Plant (TLP) of the Zambia Consolidated Copper Mines Ltd at Nchanga was commissioned in 1974 as the world's first largest successfully operated agitation leach SX-EW plant for copper production. The design, development and operation of the plant soon after commissioning termed as TLP stage II has been described by Holmes et al (1). In the initial phase the plant was designed to treat approximately 25,000 tonnes per day of current flotation tailings from the Nchanga Concentrator operations, and had a design capacity to produce 75,000 tonnes per annum of copper. Further expansion took place in 1986, and TLP stage III was successfully commissioned to treat an additional 20,000 -25,000 tonnes per day of large reserves (over 135m tonnes) of reclaimed tailings stockpiled since the early 1930's in four paddock type tailings dams (T01 to T04). The salient feature of TLP stage III expansion described by S K Mwenechanya et al (2 -3) was the installation of the world's largest Horizontal Belt Filter Plant with 26 filters each of 80 m2 filtration area.

Jan 1, 1996

By William Gleason

"Once the primary fuel source for the United States and the economic backbone for communities from Appalachia to Wyoming, coal has been on a steady decline since the mid 1990s, and is now at the center of political debate in the United States.The political spectrum of the United States is divided on the future of coal and its place in the energy sector. The coal mining industry and the communities that rely on coal have increasingly been pitted against forces that wish to regulate coal to the history books.In 2008, President Obama launched what many have called his war on coal, and during his eight years in office, he pushed through numerous pieces of regulations and legislation and that he said were aimed at reducing carbon emissions, but that others viewed as direct assaults on the domestic coal industry. Obama led the United States delegation to Paris to sign the Paris Accord in 2016, a 196-country agreement pledging that the United States would do its part to reduce carbon emissions. His administration also instituted clean air, power and water regulations that added extra environmental burdens to many industries, but perhaps none more so than the coal industry.In this month’s lead feature, “A study of U.S. coal mine closures since 1994” (page 18), the impact of the war on coal, and other factors, can be seen in text and figures. Author Jacob Brinkman and coauthors Jay Schafler and Catherine Johnson scoured the data of the U.S. Energy Information Administration (EIA) and the U.S. Mine Safety and Health Administration (MSHA) to show how coal production and mines have been impacted since 1994 and how the years 1994 to 2000 and 2008 to 2016 were particularly hard on the industry.For example, in 1994 there were 2,354 coal mines in the United States. Currently, there are 1,035 mines in operation.In 2016, then candidate Donald Trump promised to end the war on coal and to put coal miners back to work. In 2017, President Trump has followed up on those promises. He announced plans to withdraw the United States from the Paris Accord, signed an executive order designed to undo the Clean Power Plan put in place by President Obama, halted the research on the health effects of mountaintop removal coal mining, directed the U.S. Environmental Protection Agency (EPA) to revise the guidelines of waste water from power plants and has touted that more than 1,000 coal miners have returned to work since he was elected."

Jan 9, 2017

The Sage Mill Project w approved by Santa Fe Pacific Gold Corporation's Board of Directors in October 1994. The Sage Mill Project included a pressure oxidation plant designed and constructed to process refractory carbonaceous ore using fine grinding/autoclaving technology developed specifically to treat Twin Creeks ore. The project was constructed in two phases. The first phase was put into operation on May 5, 1997, just hours before the transfer of ownership to Newmont Gold Company occurred. The second phase started in October 1997. This paper reviews schedule, costs, scope changes, and methodology used on the project that spanned almost five years from project definition through commercial operation.

Jan 1, 1999

By Guodong Li, Chenlin Wang, Zibiao Yu, Bo Xu

Abandoned coal mines have many underground space resources, such as roadways, shafts, and gobs. Among them, abandoned roadways are the best gas storage space for underground compressed air energy storage (CAES). However, CAES caverns have high air pressure and strict sealing requirements. Therefore, the stability and sealing of abandoned roadways under high internal pressure must be analyzed. Afterward, the suitability of abandoned roadways used for CAES caverns should be evaluated. In this study, the numerical simulation software FLAC3D was used to calculate the stress, deformation, plastic zone volume, and pore pressure of surrounding rock in an abandoned roadway under 10 MPa internal pressure. The influence of buried depth, surrounding rock grade, and in situ stress state on roadway stability and the effect of surrounding rock permeability on roadway sealing were analyzed. Results showed that the stress, displacement, and plastic zone volume of surrounding rock were affected by high internal pressure when the buried depth was less than 300 m, but high internal pressure had little effect on them when the buried depth was more than 300 m. The suitable range of buried depth was more than 300 m. The optimal choice of surrounding rock grade was I and II, followed by grades III, IV, and V. The optimal choice of in situ stress state was σH > σh > σv, followed by σH > σv > σh and σv > σH > σh. The sensitivity of the stability evaluation parameters was ranked in descending order as follows: buried depth, surrounding rock grade, and in situ stress state. When the surrounding rock permeability was less than 1 × 10− 14m2, the 24-h air leakage rate of the roadway was less than 1%. The suitable range of surrounding rock permeability was less than 1 × 10− 14m2.

May 23, 2023

The Pogo Mine, near Delta Junction, Alaska is a new 2500 STPD gold operation. The control system of the mine and milling operations are a hybrid of DCS (Distributed Control System) control and PLC (Programming Logic Controller) control. A DeltaV DCS system serves as the main control and operation platform while the PLCs operate a multitude of vendor specific packages. The communication backbone of the DCS system is a hybrid of star and ring fiber optic topology, which provides reliability and flexibility. The communication between the DCS and PLCs is typically facilitated by serial communication. This communication insures the integrity of the whole control system.

Jan 1, 2008

By Mikko Ruonala, Pertti Lamberg, Olli Hyvärinen

The smelting of copper sulphide concentrate is the dominant route in copper production (Figure 1). Heap leaching of oxidized copper ores with weak sulphuric acid together with copper solvent extraction and electrowinning has gained popularity during recent decades, and it accounts for close to 20 % of primary copper production. Heap leaching offers advantages such as lower costs and consequently the construction of a production plant at a mine site is made possible. Limited resources of oxidized copper ores, the long leaching time of chalcopyrite and inability to recover gold inhibit this growth. The HydroCopperTM process developed by Outokumpu Technology at the laboratories of Outokumpu Research, Pori, Finland, is a new chloride leaching technology /1,2/, which offers an alternative to smelting and heap leaching (Figure 1). In the HydroCopperTM process sulphidic concentrates with various mineralogy and grade can be treated at the mine site to produce high-quality copper. Instead of copper cathodes the HydroCopperTM end products are copper wire rod, copper bars or copper billets. One of the advantages of HydroCopperTM technology is that gold can also be recovered in the process simultaneously /3/. To confirm the functioning of the new process and to dimension equipment Outokumpu Technology built the HydroCopperTM demonstration plant in Pori, Finland /4/. It has a capacity of 1 metric ton of copper per day. After testing with Pyhäsalmi copper concentrate in 2003, the first commercial demonstration run with Erdenet copper concentrate took place in 2004.

Jan 1, 2005

By Hao Zhang, Mi Zhou, Lichun Jiang, Xihong Zhang

This study investigates the roof stability of underground limestone mining in the presence of stratified joints during the excavation process. An analytical solution is derived to predict the stresses and deformation of underground tunnel structures, with the structure simplified as a double-hinge arch. The accuracy of the analytical model is validated through comparison with finite element modeling results. A parametric study is then conducted to assess the influence of different design parameters on the optimization of tunnel stability during excavation. The results indicate that the best stability of the tunnel can be achieved in engineering practices when the applied load (q) is 5 MPa and the joint inclination angle (θ) is 45°, with the roof span and thickness set at either 12 m and 8 m or 15 m and 10 m. These findings provide valuable design guidance for underground limestone mines with stratified joints.

Oct 18, 2023

By C. E. Semler

A 5 year test program, involving on-line, in-vessel exposures at Barrick Goldstrike Mines. Inc. has provided valuable information and experience about the materials and designs for brickwork linings in pressure oxidation autoclaves. A variety of brick and mortar products have been evaluated. Properties before and after exposure are used to document the performance. Benefits have included the development of a new silicate mortar improved understanding of brick requirements and increased autoclave operating time between maintenance shut-downs. More improvements are expected in the future based on further information from the test program.

Jan 1, 1997

By J. M. Pachter

Property sales and acquisition are prominent features of today's coal industry. Before selling or buying a site, a company must know the property's economic net worth. Any evaluation of economic net worth would be inadequate if determinations of a property's environmental liabilities and costs were omitted. Short-term and long-term costs can result from liabilities related to reclamation, water treatment, subsidence, and hazardous waste disposal. A structured, interdisciplinary approach can aid in the delineation, summation, and scheduling of these costs and liabilities.

Jan 1, 1986

Stillwater Mining Company (SMC) has an extensive history with tunnel boring machines (TBM) at the Stillwater and East Boulder underground PGM mines in Montana. The most recent TBM used is for the Blitz Project, where a 5.5m (18ft) diameter main beam unit, commissioned in Q3 2012, is being utilized to drive a 6,975m (22,500 ft) ventilation and haulage level East of the Stillwater Mine for the Blitz expansion project. The assembly/commissioning of the TBM, institution of the planned diamond drilling program, application of ground control systems, and the current tunneling metrics will be covered.

Feb 23, 2014