Search Documents

By A. F. Agnew

Discussion by A.E Agnew Strachan's paper summarizes a wealth of data on water-storage dam "incidents" published by USCOLD and ASCE in 1988, together with a review of tailings-dam incidents published by USCOLD in 1994. The data is summarized by text and 11 histograms. The histograms present a useful compilation of these data, although the patterns within the histogram blocks did not survive the Mining Engineering printing process - so their usefulness is impaired. Unfortunately, the text discussion is too cursory and does not highlight the significant relationships among the various causes of the incidents. Four paragraphs of text and Fig. 1 were devoted to water-storage dams, but the discussion is too sketchy, and Fig. 1 is unclear. Important statistics that could be uncovered are: •the total number of dam incidents tabulated were 500+, •earth embankments constituted 73% of those in operation and •incidents related to earth embankments were 75%, of which dam failures accounted for 24%, major repairs accounted for 42% and accidents accounted for 34%. Strachan concluded that "the majority of the dam failures are associated with overtopping (p. 49), and that the majority of incidents are associated with spillway and other facility structures" - although this is difficult to discern from Fig. 1. Confusion regarding Strachan's use of the terms "dam failures" and "incidents" is compounded by his use of "failures" and "accidents" in one paragraph of his Introduction section followed by his use of "incidents" in the next paragraph. Getting to the meat of Strachan's important paper, the tailings-dam incident survey (USCOLD, 1994), the connection between Figs 2 through 11 seems obscure. First, in the four paragraphs of introductory material, one learns that "incidents consisted of failures, accidents, seepage and other incidents of performance that did not meet design criteria" (p. 50). One does learn the helpful caveat that "structures not related to mill tailings were not included in the review" - so that the Buffalo Creek (West Virginia in 1972) and Aberfan (Wales in 1966) coal-mine failures, together with the ongoing metal-mine remediation work at Summitville (Colorado) do not muddy the waters of his paper. The all-too-brief discussion of the data shown in Figs. 3 through 11 (185 dams in USCOLD plus 26 dams in UNEP) reveals the following: •Figure 3: 57% of the incidents (failures and accidents) occurred with dams less than 20-m (66-ft) in height. •Figure 4: 63% of the incidents were due to failures alone (subset of Fig. 3). •Figure 5: Active dams had 82% of the accidents and 93% of the failures. •Figure 6: Types of dams (upstream, water-retention, downstream, centerline and "unknown") separated according to incidents. •Figure 7: Breaks out the incidents in Fig. 6 by failures, accidents and ground water. •Figure 8: Breaks out incidents by type (overtopping, slope stability, earthquake, foundation, seepage, structural, erosion, mine subsidence and "unknown"). •Figure 9: Separates Fig. 8 data into active and inactive dams. •Figure 10: Separates Fig. 9 data into failures and accidents. •Figure 11: Same as Fig. 8, but broken out by tailings-dam type (Fig. 6). Figures 6 and 7 show that most of the failures are associated with upstream or "unknown" types. Figure 9 shows that the leading causes of incidents for active dams

Jan 1, 2003

By J. O. Marsden, M. M. Botz

"Heap leaching is responsible for approximately 21 percent — 3.9 million metric tonnes — of copper production and 9 percent — 270 metric tonnes or 8.7 million ounces — of gold production worldwide. Given metal price assumptions of $2.25/lb for copper and $1,250/oz for gold, these portions of global production generate revenues of $19 billion and $11 billion, respectively. For heap leaching operations, small changes in metal extraction efficiency drive substantial changes in operating cash flow margins and affect project viability. Variances in actual metal production from budgetary forecast estimates can mean the difference between success (value creation) and failure (value destruction) for a heap leach project. Despite the importance of heap leaching for copper, gold and silver production worldwide, there are no clear standards or guidelines for developing heap leach metal production forecasts. There is considerable variation among copper and gold producers that apply heap leaching technology as to how such modeling and forecasting is applied at the operational level. There are a variety of different modeling approaches that can be utilized for this purpose. However, these vary in cost, complexity, time to implement, accuracy and credibility. This paper explores the options available for heap leach modeling, discusses the advantages and disadvantages of each approach, and provides guidelines/recommendations for an effective approach to modeling metal production at existing or planned heap leach operations. The paper also provides expected ranges of variation between actual and modeled production.Introduction and backgroundHeap leaching is fundamentally different from other methods used in the processing and extraction of gold, silver, and copper and other base metals. Considered globally, the technique represents a relatively modest portion of production compared with the primary technologies applied for copper and gold recovery. Approximately 21 percent of copper production is attributable to heap leaching techniques, as opposed to 79 percent by conventional crushing, milling, flotation, smelting and refining. For gold, about 9 percent of global production is obtained from heap leaching, compared with over 90 percent by various combinations of crushing, milling, gravity concentration, flotation and/or agitated cyanide leaching processes or, in the case of placer deposits, by direct gravity concentration and/or amalgamation. In cases where heap leaching is the primary source of metal production, the ability to accurately forecast metal production may be the difference between commercial success and failure for a project or operation. Heap leaching — of crushed or run-of-mine ore — is also commonly applied as a secondary process to treat lower-grade ores from a given deposit, such as at Chuquicamata in Chile, Cerro Verde in Peru and Bagdad in Arizona for copper extraction and at Twin Creeks and Carlin, both in Nevada, for gold. In such cases, heap leaching provides incremental revenue to supplement the primary process. Variances between actual and forecast metal production from heap leaching as a secondary process are typically tolerated and absorbed within the overall site metallurgical balance. In either case, accurate production modeling and forecasting creates significant value for heap leaching projects, is essential for managing production expectations — timing and volumes — and is likely to be a critical success factor for most heap leach projects."

Jan 1, 2017

High pressure grinding mills have been successfully introduced in the industry. They offer the possibilities for capacity increase of existing plants and reduction of operating costs. Further metallurgical advantages in gold and copper are possible. The plants in operation are running in different applications and modes of operation. They can be installed in a combination with SAG and ball mills or in a stand-alone mode. In combination with other grinding mills, it has to be investigated how the HPGR can be installed to reach the full efficiency. This paper describes the possibilities to implement high pressure grinding rolls and shows by case studies the potential of savings which could be reached

Jan 1, 1996

By D. Leppert

Large deposits of natural zeolites may provide cost-effective alternatives for treatment of soil and water contaminated ) with heavy metals and radionuclides. Research on the Bikini atoll demonstrated that addition of clinoptilolite to the soil significantly reduces cesium uptake by plants. Re- search on the potential use of zeolites in soils at Bunker Hill, ID indicated only minor benefits at very high contamination levels vs. US Bureau of Mines (USBM) work on the use of zeolites for treatment of mine waste waters emphasized problems with natural waters that previous studies have not addressed. High levels of competing calcium in natural waters significantly decrease the effectiveness of zeolites for heavy metal sorption and may limit the usefulness in these applications.

Jan 1, 1991

By T. R. Ellis

A number of important international events took place in 2001 in the development and evolution of mineral valuation standards internationally. In Canada, the CIMVal Committee released a draft discussion paper for public and industry comment on principles to guide the development of the planned Canadian mineral property valuation standard. The International Accounting Standards Board (IASB) received comments on its Extractive Industries Issues Paper. IASB will decide whether the financial statements of public mining and petroleum companies will be allowed to provide the value of mineral and petroleum assets on a current value basis instead of an historic cost basis. The author led the Extractive Industries Task Force of the International Valuation Standards Committee (IVSC) in developing its submission to IASB. IVSC intends to develop an extractive industries valuation section for its International Valuation Standards, which could support the planned IASB standard. In Australia, AusIMM has carried out an in-depth review of its highly regarded VALMIN Code. The AusIMM's MICA subdivision organized the VALMIN ‘01 Conference in Sydney, Australia, with a range of international and current issues papers published in the VALMIN ‘01 book. Considerable support for the IVSC initiative was evident at this conference. The results of the review of the extractive industries submissions to the IASB are expected to be released in early 2002. The CMMI Congress in Cairns, Australia in May 2002 is likely to prove to be an important forum for continued discussion of the development and implementation of international standards and qualifications for mineral valuation. The outcomes and implications of these events are discussed.

Jan 1, 2002

Giant gold deposits are considered products of crustal-scale systems. Reduced fluids stored in mid to lower crustal reservoirs were discharged into mid to upper crustal sites of deposition. Elements of the architecture include crustal-scale structures, reduced packages of rock and regional seals. Gas-rich aqueous fluids were common but non-aqueous fluids may have been significant in the deeper parts of the systems. Fluid fluxes in over pressured domains were maintained by porosity waves. Abnormal heat input from the mantle may not be required once the systems were perturbed. Fluid-mixing and hypogene enrichment were probably the most significant precipitation processes.

Jan 1, 1999

By Alfred Opengart

During any rush hour, tens of thousands of automobiles clog the main highways leading into or out of our large cities. Inevitably one or more cars stall or plow into another, causing a momentous traffic jam. Traffic backs up for miles as drivers try to maneuver around the roadblock. As commuters, we grin and bear the inconvenience, rationalizing the delay as part of the price one pays to live in a modern society. The truth of the matter is that the engineers planning the roads have the know-how to build adequate bypass alternatives into their design. The problem is one of economics -- can the cost of eliminating roadblocks be justified? Engineers designing solutions to complex materials handling problems for modem distribution centers are just now beginning to ask this question in relation to their work. Unfortunately in many instances, it has taken an expensive "traffic jam" to bring this question to the front. In these cases, a seemingly practical system promising an attractive return on investment -- using the latest equipment and computer controls -- was designed and installed. Everything went according to plan until one day a breakdown occurred. .Product flow stopped, and management realized it was at the mercy of the "machine." In such situations, management had assumed it could minimize the risks of the breakdown by injecting extra manpower to operate the system manually and pay the associated costs. What it had not recognized is that manual intervention is nearly impossible with sophisticated systems. Thus, too often -- and sometimes too late -- management found itself footing a very high bill for losses incurred because of major production stoppages and missed customer shipments.

Jan 1, 1973

By Zong‑yu Li, Shao‑jian Ma, Xiao‑jing Yang, Jin‑lin Yang, Xing‑nan Huo, Heng‑jun Li

Optimizing and adjusting the particle size composition of grinding products is of great significance for improving economic benefits and resource recovery and utilization. In this study, grinding contribution and quantitative separation of impact and grinding mechanism in cylindrical mill were creatively researched, and the grinding technical efficiency of impact and grinding was coupled to the grinding technical efficiency of grinding in drop-off mode. The results showed that the contribution rate of impact and grinding in grinding in drop-off mode varied with the grinding time. On the whole, the contribution rate of impact action increases with the grinding time and gradually becomes stable, and the contribution rate of grinding effect was just the opposite. Under the experimental conditions, the main contribution of the grinding process is impact action, and the contribution of grinding action is auxiliary. In addition, the contribution rate of impact and grinding effect in grinding in drop-off mode was also related to the feed particle size. The contribution rate of impact effect decreased with the decrease of feed particle size, while the contribution rate of grinding increased inversely.

Aug 3, 2023

By K. F. Unrug

Fractures of sedimentary rocks in the vicinity of the outcrop are commonly encountered around the world. Mine highwalls and numerous highway cuts give excellent views for detailed study of surface fractures. This paper gives an explanation of the origin of fractures as well as characterization of the distribution and extent of joint system with reference to lithologic composition of the rocks. Practical implications of the joint system affecting mine operations are described. Among the subjects discussed are: discontinuous deformation as an effect of surface subsidence, stability of mine portals and near outcrop underground operations, and stability of highwalls, when using highwall miners and strip operations. Some design procedures are recommended that can minimize the problems encountered in mining areas with intense joint systems.

Jan 1, 1994

By H. G. Kok

The concept of mobile crushers is not new. Since their introduction about twenty-five years ago, mobile crushers have continued to gain widespread attention. Mobile crushers reduce minerals in the open pit mine to sizes which can be transported by belt conveyors thereby reducing or eliminating the need for truck haulage. Truck haulage is costly, often representing as much as 50% of the total mining cost. More than 80% of the cost of truck haulage is for fuel and lubricants, tire replacements, and operators' wages, and it can be anticipated that the cost of these items will continue to increase at a steady pace. Compared to truck haulage, transportation by belt conveyor is more energy-efficient, less labor-intensive, and less subject to inflation. Therefore, mobile crushers, used in conjunction with belt conveyor systems, offer one of the most effective available methods of reducing energy consumption and mining costs,

Jan 1, 1980

By Howard M. Graff

The Inland Steel Company operates five underground iron mines in the Lake Superior District. The two largest of these, from the standpoint of productive capacity, are the Sherwood Mine in Iron River and the Bristol Mine in Crystal Falls, both on the Menominee Range of Michigan. It is at these two mines that we have had our principal experience with belt conveyor installations underground, .At the Sherwood Mine, which has an annual capacity of about 450,000 tons, the first conveyor belt installationwas made in 1947 when conveyors were installed in the main haulage drifts on the 1200 ft, level, It was estimated at that time that approximately 5,000,000 tons would be mined from the stopes above the 1200 ft, level and. that if all this material could be moved to the shaft by belt conveyor, the entire cost of operation, including maintenance and the amortization of the equipment, would be about $,05 per ton, which was slightly more than half of what the cost would have been by conventional tramming methods employing locomotives and cars. Now, ten years later, the 1200 ft, level is almost completely mined out and we have actually removed. 5,200,000 tons and. the average cost of transporting this material to the shaft by belt conveyor has been $.095 per ton. Since there has been a substantial increase in hourly rate of pay and also in the cost of materials since 1947, we feel that the anticipated savings were very nearly realized., The 1200 ft, level installation at the Sherwood consisted of two 36" trunk line conveyors 815 feet long and 380 feet long, respectively, deliverying ore to the shaft. These in turn were fed. by three lateral 36" conveyors which paralleled the sides of the orebody, These gathering conveyors passed under draw points to which ore was brought from the stopes by mea S of scrapers or shaker conveyors, Shaker conveyors were used for a number of years in conjunction with the conveyor belt system of haulage but it was finally concluded that with this particular type of ore, the maintenance on shaker conveyors was excessive. Therefore, more recently, we have gone back to scrapers for the shorter distances and. are using belt conveyors in the scraper drifts for the longer distances. After this belt system had been in operation for about three years, it had proved to be so successful that it was decided to proceed with the same system or. a new level to be opened up 200 feet below. Instead of sinking the shaft and driving a horizontal drift to the orebody on the 1400 ft, level, an inclined conveyor drift was started near the shaft at the 1200 ft. level and driven downwards toward, the orebody at a slope of 15 degrees. The conveyor installed in this inclined drift is 36" wide, 990 feet long, is powered. by a 100 hp motor, and is capable of delivering 300 tons per hour to the 1200 ft, level shaft pocket. It is fed by lateral horizontal conveyors on the 1300 ft? 1400 ft., and 1425 ft, sub levels. Wien the inclined drift was started, the rock was scraped from the breast directly to the rock pocket at the shaft. As the distance increased., double scraping was employed, until the advance had reached 350 feet, At this point a portion of the final conveyor was installed, with a scraper slide near the breast, T e drift was then advanced be scraping on to the conveyor until a sufficient distance had been driven to permit the installation of an additional 200 feet of conveyor. This proved to be a very efficient and economical means of moving the development rock to the shaft and obviated the need of using cars or an inclined skip way, At the present time 85 percet of tie entire mine output is being mined below the 1200 ft, level and is delivered to the shaft via the inclined conveyor. The system appears to be working as well and as economically as did the conveyor systemonthe 1200 ft, level.

Jan 1, 1958

By V. P. Petrov

There is a great number of asbestos deposits in the USSR. Some of them are quite large ones. The main deposits of chrysotile asbestos can be seen in the sketch map (fig. 1). Bazhenovo deposit situated in Sverdlovsk region is the largest of them. It is on mining operations since year 1889. Systematical studies of asbestos deposits were begun from the first years of Soviet Government and connected with the names of K.E. Tarasov, P. M. Tatarinov, B. J. Merenkov, N.D. Sobolev, F. V. Syromjatnikov, V. N. Lodochnikov, V.P. Petrov, V.P. Eremeev, L.A. Sokolova, V. R. Artemov, V.F. Dybkov and many others. This investigations served the USSR to be one of the most important producers of asbestos in the world. In the limits of the report a characteristic of the main asbestos deposits of the USSR may be done in general outline, from the point of view of their genesis, and in order to show their common features and differences that must be taken into account for forecasting, exploration, and mining of asbestos. All chrysotile asbestos deposits of the USSR were formed of magnesium rock as a result of comparatively lower-grade temperature hydrothermal alteration and free crystallization of fibrous chrysotile in open cavities that served as catalyst As a matter of fact an important mineral for industry is not chrysotile in general, a widely distributed rock-forming mineral, but a long fibrous and mainly vein variety of chrysotile. It must serve for geologists as an important prospecting criteria. A geologist should search for the mineral not only places of possible chrysotile generations, but places where asbestos may be crystallized in its long fibers that could be fiberized well. The Soviet geologists distinguish two groups of chrysotile-asbestos deposits: (1) related to ultrabasic rocks and (2) related to sedimentary dolomite terranes, taking into account what the maternal rock was affected by hydrothermal solutions. The largest deposits related to ultrabasite. The largest deposits in dolomite are small ones but their asbestos contains almost no iron. So much asbestos is a better filler into insulating plastics. There is a few types of asbestos deposits in the limits of the ultrabasic group. The largest of them is a Bazhenovo type which the deposits of Urals are attributed, and Bazhenovo deposits is the first instance. The Bazhenovo type is characterized by the most complete zonality in disposition of various kinds of asbestization. This type of deposits is practically the only one to be in working now in the USSR.

Jan 1, 1978

By R. Brown, A. J. S. Spearing, M. Treinen, M. Theisinger

The mining and use of coal creates a significant amount of waste material that needs to be safely disposed of. It is likely that in the medium term, the Environmental Protection Agency (EPA) in the U.S. will categorize all such products as a new category – special waste. This would make the materials subject to many of the requirements for handling toxic waste, which will complicate the disposal of such products and significantly increase the disposal costs. Underground disposal would, therefore, seem to be the obvious solution, especially if the placed material can have low or no permeability, so that water table pollution does not present a serious long-term issue after placement. Significant additional advantages could be derived from this backfilling, including the reduction or elimination of surface subsidence, increased extraction, reduced surface waste disposal footprint and the elimination of explosion-proof seals in worked out areas. The research using a specific coal waste product as a typical example proved that the method of placing the backfill at a high density with low permeability is technically viable, but it must be made more cost effective and the other potential benefits quantified and costed in order to present a true comparison.

Jan 1, 2010

By A. Güngör, Ü. Atalay

Thermal treatment can significantly improve industrial comminution operations by reducing energy requirements and increasing mineral liberation. The assistance of thermal pretreatment prior to grinding by microwave heating is scrutinized in this study. For this purpose three copper ore samples with different chemical composition were used. To see the effect of microwave heating on ore; work index, breakage rate and breakage distribution functions of original and heat treated samples were examined. The results obtained in this study did not show significant improvement in the grindability characteristics of the studied ores with microwave heat treatment. The inadequate amount of microwave transparent matrix was the main reason for the absence of cracks and micro-fractures in the microwave heated copper samples.

Jan 1, 1999

By Paul G. Schmidt

The Crandon massive sulfide deposit Forest County, Wisconsin, was discovered by Exxon Minerals Company, U.S.A., in July 1975. Announced estimated in-place reserves are 62 M metric tons (70 million short tons), grading about 5% zinc and 1% copper. The reserves are evenly divided between massive sulfide are and stringer sulfide ore. The sulfide body is associated with Precambrian felsic pyroclastic rocks, and it is overlain by intermediate volcanic rocks and their derived sedimentary rocks. These rocks were subjected to greenschist facies metamorphism and were tilted to a near-vertical attitude. Geologic observations indicate a submarine-volcanic-exhalative origin for this deposit.

Jan 1, 1978

By J. Humphrey

Introduction The weight of a Mining Truck can be affected by field modifications, the selection of items like tires, rims or even the conditions in which it operates. Truck performance and the compliance with a number of ISO standards, e.g. braking, steering and ROPS are dependent on truck weight. It is critical that truck owners understand the impact of changes in weight1. What makes this even more difficult for owners to evaluate is that there is no standard terminology or definitions for Mining Truck weights. This paper discusses and defines weight terminology, how it applies to performance and standards and the impact on the application of Mining Trucks.

Jan 1, 2007

By M. Brnich, S. Kramer, B. McNamara, T. Hethmon, M. Pedersen-Howard, S. Rajapaske, D. Lingenfelder, B. Huber, D. Hebig

"The development of mining safety and health management as a recognized profession has been long in coming. Over the last 150 years, the mining industry has evolved from having individuals randomly involved in safety related work with no specific responsibilities or qualifications, on to the designation of individuals responsible for safety, regardless of knowledge, qualifications and experience and finally to today’s expectation that virtually every mine and mining company has designated individuals operating as safety and health professionals. Further, with the complexity, risk potential and moral expectations surrounding safety, people who address mine safety and health management are justifiably expected to function in a professional capacity including:1. Rendering a specialized service based on advanced knowledge and skill.2. Maintaining a high degree of obligation to those most affected by mine safety outcomes.3. Bound by an ethical code in working with the public, employers and miners.4. Maintaining confidentiality with an employer or client. This historical change parallels thedevelopment of other professions, e.g., attorneys, engineers, physicians, etc., with the exception that those professions require a license granted by a governmental agency, which is justified on the basis of public protection, in order to practice. Likewise, decisions made by today’s mine safety and health professionals, both directly and in association with other managers, clearly have a significant impact on the life and welfare of miners throughout the world.CertificationIn light of this, there is growing need to improve standards of competency and professionalism for those who work in mine safety and health management. An effective mechanism to accomplish this, other than licensure, is the use of accredited professional certification programs. There are many professional certification programs for safety and health throughout the world (Hale & Harvey, 2012). However, there is only one certification specific to mining —the Certified Mine Safety Professional (CMSP). The International Academy of Mine Safety and Health (ISMSH-SME) was formed with the purpose of developing and managing mining safety and health certification programs for the Society for Mining, Metallurgy and Exploration (SME). In 2016, following the discontinuation of the International Society of Mine Safety Professionals (ISMSP), which developed the Certified Mine Safety Professional (CMSP) credential in the 1990s, the IAMSH-SME began the process of updating and relaunching the CMSP program. Among other work required to gain third-party accreditation both domestically and internationally, the IAMSH-SME has developed a new Body of Knowledge associated with mine safety and health management (Table 1)."

Jan 6, 2018

By Dermot M. Ross-Brown

The objectives of this generic study were to use numerical modeling techniques to determine under what conditions seismic waves generated by an earthquake might cause instability to an underground opening, or cause fracturing and joint movement that would lead to an increase in the permeability of the rock mass. In general, the study showed that moderate earthquakes (up to 0.41 g) did not cause instability of the tunnel or major fracturing of the rock mass. An artificial rock-burst tremor with high accelerations, however, was found to be amplified around the tunnel, and fracturing occurred as a result of the seismic loading in salt and granite. In shale, even moderate seismic loading resulted in tunnel collapse.

Jan 1, 1981

By Charles H. Ricker

Simulation models have been widely used to analyze the operations and characteristics of a variety of systems. Such models mimmick a projected reality by analyzing the interaction of the events, transactions, and facilities which combine to make up the system. The models are structured as a computer representation of the system components and their logical, precedence and timing relationships. The operation of the system is then simulated over some finite time interval to gather analytical and staistical data. This paper presents a method whereby bulk handling systems, either actual or proposed, may be analyzed by means of simulation models to project the enconomic consequences which may be expected from the system over some future time interval. An example is given to illustrate the construction of bulk handling simulation models, the derivation of performance data, and the analysis of the information with an eye to effective decision making.

Jan 1, 1974

By Liming Yuan, Wei Tang, RICHARD THOMAS, JOHN SOLES

Lithium-ion battery pack fires pose great hazards to the safety and health of miners. A detailed experimental study has been conducted at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) to investigate the effectiveness of different fire suppression systems on Li-ion battery pack fire extinguishment. Tests were conducted in a well-ventilated container. Two sizes of battery packs (12 V, 24 V) were heated by heater strips to trigger thermal runaway and fire. Water mist with different flow rates, ABC powder, type D dry chemical, and water mist with F500 additives were used as the fire suppression agents. Multiple thermocouples were installed on the battery packs to measure the temperature evolution during the tests. The results indicated that the water mist with F500 additives is the most effective suppressant among the agents tested. Dry chemicals, however, do quench the fire for a moment, but cannot prevent re-ignition of the battery since they do not provide enough cooling. The findings of this paper can be used to develop safer battery fire suppression techniques in mining environments.

May 4, 2023