Search Documents

By M. K. Larson, R. G. Wade

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are studying the time-dependent response of rock stressed along weakness planes. The objective is to improve mine safety by reducing the number of roof falls that cause injuries and fatalities to miners. Researchers conducted direct-shear tests on mud-stoneovercored from a coal mine roof. Results showed frictional strength weakens with displacement along the shearing planes. Results of direct-shear creep tests also showed time-dependent deformation. Test measurements were compared to classical analytical models. Results suggest that risk of roof collapse may be decreased through layout and support design to reduce creep rates and thus slow progression toward failure.

Jan 1, 2000

By William M. Gray

[The products of mites hive historically beet a very large and important segment of total shipment transported by American Railroads. Much as the Mining transportation Executives right have wished for coal and other mineral deposits to be found along navigable rivers, where railroads have for years been competing with the very aggressive Army Corps of Engineers and the inland waterway operators, the mineable reserves are more often that not located in the arid west far from these "free" waterways. The rivers cannot go to the mines but the railroads could, did, and continue to invest it new lines to reach new mines. The mining industry and the railroad industry have good reason to rely upon each other. The former Northern Pacific Railway, the Great Northern Railway, the Chicago, Burlington and Quincy Railroad and the Spokane, Portland and Seattle Railway merged in 1970 to form the Burlington Northern Railroad, with Lou Menk as its first President. As unofficial spokesman for the industry, be had, for years, conducted a tireless effort to educate shippers, lawmakers and the general public of the single most critical problem confronting the railroad industry, the strangle bold of government regulator.]

Jan 1, 1985

By Edward H. Jr. Boyle, Paul R. Thomas

Introduction It is estimated that nearly 40% of all the gold ever mined in free world countries has been produced by South African operations. There is concern that this immense productive capacity will soon decline. Such a decline could reduce world gold supply and lessen the ability of market economy countries (MEC) to exert the major influence upon the world gold market. This paper addresses three general issues concerning South African gold production: • How much gold remains to be recovered from the demonstrated resources of the 44 evaluated South African mines; • How long can production at current levels continue; and • What will be its cost. Table 1 provides production data on the world's 10 largest producers for the years 1971, 1981, and 1983. As shown, South African gold production declined significantly from 1971 through 1981. As of 1981, annual South African gold production had dropped by more than 311 t (10 million oz) in 10 years. Despite this, its mines still produced 656 t (21 million oz) that year, about half the world total. From 1981 through 1983, this trend was reversed. Annual South African gold production increased by more than 21.8 t (700,000 oz). The trend reversal was also evident in the US, Canada, and Australia. This illustrates the general, inverse relationship between gold price and gold production. In South Africa especially, as gold prices increased substantially during the 1970s, the average grade of ore mined (pay limit) was lowered as new, lower grade areas and materials were exploited. Gold production declined in volume. But gold revenues increased, and the lives of the operations were extended. The 1981-83 period was one of declining (US dollar-based, average annual) gold prices that resulted in increasing South African production as average ore grades were raised. South Africa currently accounts for 50% of world production (Fig. 1). Figure 2 illustrates South Africa's contribution to total MEC production in 1971 and 1983. Although South Africa's relative share of production has declined, it still represents the single most important source of new gold supply. In 1983, it supplied more than 65% of total MEC production. South Africa currently produces more than twice as much gold as the Soviet Union (ranked second in world production), and 11 times more gold than the US (ranked fourth in world production). Barring major discoveries, South African gold production is expected to peak in 1987 and begin to decline again throughout the 1990s. The rate of decline is ex-

Jan 11, 1984

By Anthony G. Fonseca

The acid leach-solvent extraction processing of oxide copper ores can be improved when selected cation additives are utilized. Bench scale testing showed improvements in both sulfuric acid leaching and solvent extraction processing. Treatment with the method to be described shows improvement in copper recovery in the acid leaching section as well as reduced acid consumption and reduced iron and aluminum dissolution. Processing the copper bearing leach solution with LIX-64N shows increased loading of the LIX reagent which relates to reduced aqueous and organic flow rates, reduced organic loss and inventory as well as a reduction in the size of mixer-settlers. The use of selected monovalent cations controls fluctuations within the pro- cessing system to accomplish the above named improvements. Additionally, these cations are totally compatible throughout the processing system and are quite inexpensive. Bench scale recycle data will be presented both for the leaching section and the continuous solvent extraction processing section up to (but not including) processing the loaded electrolyte. Material balances as well as major solution component monitoring will also be presented.

Jan 1, 1975

Column flotation has been successfully implemented on a production scale in the Athabasca oil sands. In this application, bitumen is recovered and mineral matter is simultaneously rejected from a middling stream originating from a primary separation vessel. Exploiting the natural hydrophobicity of bitumen, the middlings streams have traditionally been processed utilizing conventional, mechanical flotation cells. Although these cells offer adequate bitumen recovery and mineral rejection rates, operating costs are high due to the required maintenance of the wetted mechanical components. In comparison, column flotation provides superior metallurgical performance while offering a lower maintenance demand. Both metallurgical and mechanical characteristics of column flotation are discussed to demonstrate the benefits of this technology for the recovery of bitumen from oil sands.

Jan 1, 2012

By Weiran Zuo, Wanzhong Yin, Jin Yao, Keqiang Chen, Qiuyue Sheng, Liu Liu

It is important to investigate the liberation properties of gangue minerals and establish liberation models for low-grade iron ores to reject gangue early. In this study, three types of iron ores from different iron deposits were ground to different particle size distributions by locked-cycle grinding and batch grinding. The liberation distribution of quartz, the most dominant gangue mineral among the three types of iron ores, was tested by Mineral Liberation Analyzer (MLA). Afterward, the liberation distribution of the three types of quartz was fitted using the beta distribution function, and their shape parameters were related to particle sizes to develop the liberation model. MLA test results showed that the liberation distribution of quartz with different grinding methods was basically the same. The developed liberation model predicted the liberation distribution of quartz in low-grade iron ores from different iron deposits well, and its coefficient of determination (R2) was between 0.90 and 0.98. This study deepens the understanding of the liberation rules of quartz in low-grade iron ores from different iron deposits, and on this basis, a more efficient liberation model based on the beta distribution function is developed.

Oct 18, 2023

By Chelsea Woodward

The Spokane Research Laboratory of the National Institute for Occupational Safety and Health has demonstrated a prototype hydrogen-fueled mining vehicle as an alternative to diesel equipment in underground mines. Safety and control systems were added to allow a 70-kW rubber-tired hydrogen vehicle, originally developed by the U. S. Bureau of Mines and Hydrogen Consultants, Inc. (now Hydrogen Components, Inc., of Littleton, CO), to be tested. This work began in late 2000 and culminated with a Mine Safety and Health Administration fire safety review and field tests at the Stillwater Mine in Nye, MT, in 2004.

Jan 1, 2006

By A. W. Khair

This paper presents an analysis of the dynamics of bit wear on the productivity of the continuous miners. Two field surveys have been carried out. The first survey was to assess the impact of bit wear on productivity and production cost. The second survey was to study the wear characteristics of the cutting tool (i.e. magnitude, forms, and mechanisms of bit wear). Primary factors affecting bit wear is identified and laboratory experiments were carried out to study the effects of some of these primary factors on wear in detail. Results indicate that bit wear has a significant effect on the productivity of the continuous miners. Furthermore under the severe geologic conditions (i.e. cutting rock partings and roof and floor rocks) bit wear not only hampers the productivity, but also increases the production cost due to a higher number of bit consumption. This study also indicated that bit wear accelerates beyond 20% of the conical height loss which corresponds to 7% of the weight loss. This increase rate of wear is an indicative of higher abrasion between bit body and cutting material, resulting in a dustier environment.

Jan 1, 1993

By S. G. Malghan, J. P. Van Dillen

Introduction Some uranium minerals are paramagnetic and hence are amenable to concentration by high gradient magnetic separation (HGMS). This paper describes effects of the HGMS parameters-pulp velocity, field strength, matrix loading, and magnetic field gradient-on the product recovery and grade. Unsatisfactory separation of uranium minerals by HGMS is related to ore-specific properties, such as lack of liberation, fine dissemination of uranium minerals, uniform distribution of magnetic minerals throughout the ore matrix, and interference of fine-sized slimes. Experimental techniques to identify and resolve some of these problems are outlined. HGMS of Uranium Ores The mechanism by which uranium minerals are attracted to a magnetic field is either due to its magnetic susceptibility or its association with other minerals that are magnetic. Data on magnetic susceptibility of uranium minerals are scarce. The only reported data are for uraninite at 2360 X 10-6 cm3/mole. Povarennykh (Andres, 1976) concluded that the magnetic properties of minerals depend on: • Structure of the outer electron shell in a mineral with electropositive atoms; • Valence of the atoms; • State of the chemical bonds; • Type of coordination; and • Proportion of magnetic atoms (Fe, Mn, Cr, and Ni) in the composition of the mineral. However, information on the magnetic susceptibilities of the constituent atoms of a mineral alone does not suffice for evaluating the mineral compound as a whole. Most often, uranium minerals can be beneficiated by HGMS if they are associated with other minerals that are magnetic. This appears to be a more predominant mechanism by which the uranium minerals are beneficiated. Experimental A Sala-HGMS (Malghan and Subramanian, 1981), model 10-15-20, separator was used in the experiments. The matrix material-ferromagnetic stainless steel in the form of expanded metal or steel wool-was packed into a 38-mm (1.5-in.) diameter by 360-mm (14-in.) long canister. The matrix material occupied only a 150-mm (6-in.) length. The experimental set-up and slurry flow direction are described elsewhere (lannicelli, 1976). The response of uranium ores in the HGMS was studied by feeding well-dispersed slurry at 10% solids and examining the influence of process variables on selectivity and overall uranium recovery. The chemical and mineralogical characteristics of the ores under study are presented in Table 1.

Jan 12, 1983

By S. B. Bealko

In response to recent mining disasters and new mine rescue team legislation, NIOSH researchers conducted meetings across the United States with mine emergency response experts to investigate current needs and issues. Some of the issues include emergency response preparedness, mine rescue contests, real-life training capabilities, and training facilities. Many new teams are being formed that must be trained for mine rescue team competitions as well as be ready to respond to a variety of mine emergencies including a fire or explosion, a massive roof collapse, mine inundations, or vertical shaft rescue situations. Therefore, it is important that these teams are adequately prepared and trained. This paper presents a summary of domestic and international coal mine rescue training facilities and identifies those that provide unique, real-life, and/or state-of-the-art training. Research findings from this report will be used in further NIOSH investigations to improve coal mine rescue training. DISCLAIMER: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2009

By Klaus Rieker

North of Antwerp central train station, two single-track tunnels for the high-speed train line between Brussels and Amsterdam were constructed. At the same time, the central train station was modified to a through station. Both 1.23 km tunnels are situated in the Antwerp sands and were constructed using a slurry shield machine. Due to the inner city location, the tunnels run over their entire length underneath structures, in some cases with only minimal clearance. The paper deals with these challenging situations. In addition, the tunnel boring machine, the tunnel lining and measures to limit settlements will be introduced.

Jan 1, 2007

By W. Burger

For the development of deep, hard rock, mines fast access to the orebody is critical. In some cases the mineralized area is more than 1,500 m (5,000 ft) below surface. Excavation of shafts or declines is typically on the critical path of the project schedule. Saving time on those activities can significantly increase the net present value of the mining project. Mechanical excavation methods are a step-change in excavation performance and labor safety compared to drill-and-blast operations. In hard rock conditions, roadheaders cannot be used effectively, so disc cutting is the first choice. For excavation of declines, tunnel boring machines (TBM) can be used in many cases. These provide, in certain rock conditions, considerably higher production rates com-pared to drill-and-blast excavation. Herrenknecht AG has developed a vertical shaft sinking machine (VSM) that is able to excavate shallow shafts in soil and medium soft rock. The ground is excavated by a roadheader boom. The muck is removed by a slurry system or a pneumatic system in combination with hoisting of skips. These machines have been applied successfully on shafts down to 100 m (300 ft). A pre-sink for a deep mine shaft has been excavated by this technology. For deep, hard rock shafts, a new shaft boring system has been developed by Herrenknecht AG in collaboration with Rio Tinto. Based on proven technologies, the system uses a unique arrangement of existing proven technologies. The system integrates excavation, mucking, primary rock support, installation of the final lining and shaft infrastructure. This new system improves the health and safety of shaft construction. Detailed performance estimates indicate significantly higher shaft construction rates are possible compared to conventional shaft sinking methods.

Jun 1, 2010

By R. Cooper, K. De Wet, A. Janwong

"Horsehead Metal Products is a zinc refinery in Mooresboro NC treating crude Waelz Oxide (WOX) to produce Special High Grade Zinc by a hydrometallurgical process, comprising leaching, zinc solvent extraction/electrowinning (SX/EW), melting and casting and bleed treatment. Cadmium removal by zinc dust cementation plays an essential role in the bleed treatment circuit to prevent a build-up of cadmium in the circuit. Silica, although not present at significant levels in the WOX feed material (approximately 0.3%), had a significant impact on the efficiency of cadmium cementation with zinc dust, most likely due to the passivation of zinc dust particles with silica gel. Solid/liquid separation efficiency by filter press was also impacted. The silica levels were mapped throughout the circuit in an attempt to identify the source of the silica issues. Adjustments including using PLS as feed to cementation, pH control in WOX leaching and neutralization have been introduced to mitigate the issues created by silica gel in the circuit. INTRODUCTION Located in North Carolina, Horsehead Metal Products Inc. is a hydrometallurgical zinc refinery processing Waelz Oxide (WOX) to produce Special High Grade (SHG) zinc. The flowsheet, known as the Modified Zincex® process, consists of leaching, solvent extraction, electrowinning, melting and casting and bleed treatment as illustrated in Figure 1. Cadmium cementation, part of the bleed treatment process, provides an essential bleed of cadmium from the circuit, as metallic cement. The Cadmium cementation circuit consists of agitated cementation reactors, a zinc dust addition system, filter presses, agitated purification (releach) reactors and a cadmium concentrate filter press Silica can be found in several forms in acid leaching. The first form is fine silicate particles. The size of the particles can vary from one to twenty microns (1). Fine silicate particles can lead to the formation of crud in solvent extraction circuits (2, 3). At Mooresboro, crud has been observed in Depletion, which is part of the solvent extraction circuit. Silica content in the solution in this section is high. The second form of silica is monosilicic acid Si(OH)4, which begins to polymerize almost immediately upon being leached into solution. Monosilicic acid polymerizes to silica gel or a silica precipitate dependent primarily on supersaturation (5). Factors that influence the rate of polymerization include temperature, sulfuric acid concentration / pH, hydrofluoric acid concentration, seeding, and dissolved salts concentration such as zinc and aluminum in the solution (4, 5, 6). In sulfate systems, silica solubility is reported in the range of 150 to 450 ppm of SiO2 (3, 5, 7)."

Jan 1, 2016

By J. K. Brooke

Fluorine is a lively element in both its chemical and economic behavior. It was not isolated as an element until 1886 by Moissan. However, its principal source to this day, fluorspar, was known and its special merits recognized long before that time. Our own mining brother, Agricola, is credited with having named fluorite, the mineral name, in 1546 from the Latin, "fluere", to flow. It made things melt and was already being used as a flux. Because fluorspar has been found as a relatively common gangue mineral in metal ore veins, it has long attracted the attention of geological thinkers seeking to, explain the whys and wherefores of veins. Fluorine has been thought of as one of the principal mineralizers, holding metals in ascending vein solutions for deposition close enough to the eventual surface to be accessible for profitable mining.

Jan 1, 1964

By S. F. Diehl

Suites of monomineralic sulfide and carbonate minerals, as well as mine-waste composite samples, were analyzed using chemical and microanalytical techniques to understand behavior and bioavailability of mine waste elements such as Cu, Fe, Pb, or Zn. Petrographic, scanning electron microscopy (SEM), and laser-ablation inductively-coupled mass spectrometry (LA-ICP-MS) studies of mineralogical residence sites of trace elements are important because trace elements affect the chemical and physical behavior of minerals. Leachate solutions show that chalcopyrite, bornite, azurite, malachite, and galena are host to the trace elements Ag, Al, As, Cd, Co, Cr, Mn, Ni, Pb, and Zn. SEM studies reveal whether these trace elements occur within mineral inclusions or are substituted within lattice structures. SEM analysis reveals mineral phases not identified by X-ray diffraction (XRD), such as inclusions of sphalerite and cobaltite(?) within chalcopyrite.

Jan 1, 2010

By L. E. Sausa

Measuring the specific gravity of a pulp in concentrating plants is a relative, y simple procedure, but the desired accuracy is often difficult to attain. Many plants use the system of weighing a known volume of the pulp on a scale. In many cases, this method is quite accurate, but obtaining a true sample presents quite a problem. This is especially true when the pulp tends to froth, the solids settle rapidly, or the flow is fast at the point of sampling. There is also the problem of the operator neglecting to take the sample because of duties elsewhere, or, if everything Is apparently running smoothly, he assumes the pulp density is also all right. In 1952, the Pine Creek plant of Union Carbide Nuclear Company began working on a better method for measuring and controlling pulp density. After an extensive investigation of different methods for measuring the specific gravity of moving pulps, the Research Department decided that the bubble tube method appeared to be the simplest and most promising for our applications. It consists of two bubble tubes, of different lengths, submersed in a pulp. Low pressure air is supplied to, the two tubes through sight bubblers to maintain approximately equal volume of air to each bubble tube. The bubble tubes are also connected to a differential manometer, one to each side. Therefore, knowing the vertical distance between the outlets of the bubble tubes, the manometere can be calibrated to measure directly the specific gravity of the pulp. (Figure No. 1 illustrates this model.)

Jan 1, 1960

By W. N. Brown

One of the seemingly eternal problems with which we are frequently faced is that of providing adequate and economical warehousing facilities to store large quantities of bulk product. Seasonal consumption, transportation, marketing, and other factors very often dictate extensive product warehousing requirements for an operation geared for steady, year-around production of a material requiring weather protection during storage. Fertilizers such as potash and urea are examples of such products; the consumption of these materials is extremely heavy in the early spring at which time the materials must be placed in the soil, whereas, for obvious operating efficiencies, production is more or less constant for a given operation throughout the year.

Jan 1, 1961

By S. Ilyas

Technical innovation in electrical and electronic equipment with new functions and design, stimulate consumer?s purchasing desire towards the latest equipments and this leads the rapid increase in the production of increased amount of waste materials Treason et al (2006) have reviewed the data on electronic waste generation in different parts of the world. Studies by Bertram et al (2002) have also affirmed that waste electrical and electronic components are the fastest growing waste category; this emphasizes the need for efficient recycling strategies. Recycling of electronic waste is an important subject not only from the point of waste treatment but also from the recovery aspect of valuable materials. However, recycling of electronic scrap is still quite limited due to the heterogeneity of the materials present in the products (Veit et al. 2005). A bioleaching based process offers a number of advantages compared to the conventional pyro or hydrometallurgical methods (Lee et al. 2007; Lee and Pandey, 2012). The advantages include simple, inexpensive (in some cases) and eco-friendly approach besides, generation of less active leach residue then other metallurgical processes. Though, biohydrometallurgical process has been successfully applied for the leaching of metals from ores (Olson et al. 2003; Rawling 2000), data pertaining to its application for the extraction of electronic scrap is still scanty. Recently, a few studies have been undertaken for extraction of metals from electronic scrap/printed circuit boards (Brandl et al. 2001; Faramarzi et al. 2004; Choi et al. 2004, Ilyas et al. 2007; Ilyas et al. 2010). These studies were conducted with mesophilic chemolithotrophic (Acidithiobacillus ferooxidans and Acidithiobacillus thiooxidans) or cyanogenic bacteria (Chromobacterium violaceum) or moderate thermophilic bacteria (Sulfobacillus thermosulfidooxidans). However, compared to bacterial leaching, fungal leaching has the following advantages: (i) ability to grow under higher pH, and thus is more suitable in bioleaching of alkaline solid waste (ii) a generally faster leaching process with shorter lag phase (iii) Chelation of excreted metabolites (e.g. organic acids) with metal ion, thus reduce its toxicity to the biomass (Burgstaller et al. 1993; Aung and Ting 2005). The specific objective of this work was to; ? Collection, isolation and enrichment of fungal strain ? Evaluate the abilities of Penicillium chrysogenum to leach metals from electronic scrap at various leaching modes (one-step bioleaching, two-step bioleaching, spent medium leaching, fresh medium leaching, leaching with deionised water and chemical leaching). ? Comparative study of all leaching modes

Feb 27, 2013

By C. R. Stephan

Explosion-resistant seals in underground coal mines isolate the environment within the sealed area from the active workings of the mine. The current United States Title 30 Code of Federal Regulations (CFR) requires these seals to be constructed of solid concrete blocks. The CFR also allows for alternative methods or materials to be used to create a seal if they can withstand a static horizontal pressure of 138 kpa (20 psi), provided the method of installation and the material used is approved in the ventilation plan. The purpose of this report is to identify those explosion- resistant seals that have been tested and meet or exceed all the requirements of the CFR.

Feb 24, 1997

The Virginia Center for Coal and Energy Research has been developing models of wireless signal propagation in underground coal mines since 2007. The current mine propagation modeling software, named COMMS, is able to locate potential broadcast points for underground wireless mesh systems and estimate their coverage. COMMS utilizes programmed routines to calculate necessary values to both quantitatively and qualitatively solve and analyze predicted coverage areas. The program approximates the spatial relationships that are encountered, such as ventilation regulators, belts and other obstructions. Using this model for propagation allows the optimal communications node locations to be calculated, by using lessons learned from current installations and experience with the new technology. In addition, the optimization can be calculated by checking all possible combinations of broadcast locations. This paper compares these optimization calculation methods. The ability to solve a mine?s communication network provides a pre-installation mine network design map, creates coverage maps of the mine and allows planning for future communication activities

Jan 1, 2011