Search Documents

By Arthur R. Still, Paul A. Bailly

5.1-PURPOSE, PROCEDURE, METHODS, MANAGEMENT Exploration can be technologically defined, with regard to the discovery of new mineral deposits, as all the activities and evaluations necessary before an intelligent decision can be made establishing size, initial flowsheet and annual output of new extractive operations. The purpose of mineral exploration is the discovery and acquisition of new mineral deposits amenable to economic extractive operations now or in the future. A prime objective of mineral exploration, however, is to find and acquire a maximum number of such mineral deposits at a minimum cost and within a minimum time. Immediately upon the heels of a successful ''exploration" discovery follow activities called, first, development, then operation. Under U.S. Internal Revenue Code regulations (Secs. 1.615.1 and 1.616.1) in effect at the time of this writing, which state that the "development stage" has been reached when "deposits of ore or other minerals are shown to exist in sufficient quantity and quality to reasonably justify commercial exploitation by the taxpayer," exploration in the technological sense may well continue after a mineral property has entered the "development stage" as defined for tax purposes. In many instances continued exploration, after reaching the tax defined "development stage," has disclosed additional reserves which justify a much larger, more efficient and more profitable operation than that which would constitute the minimum feasible. Even after a mine goes into production, continued ore search generally will increase the reserves, either justifying expansions in plant capacity or prolonging the life of the operation, but this work (actually "exploration") is normally considered, for bookkeeping and tax purposes, a part of mine development. Each exploration entity defines its own objectives in terms of acceptable mini- mum rate of return on investment for any deposit found and retained, and in terms of which commodities, and markets, are to be involved. For these reasons, exploration programs, and aims, will vary over a wide range, although all have the common objective of endeavouring to create new profit centers for the future. 5.1.2-EXPLORATION METHODS Exploration has evolved in the past several decades into a highly sophisticated and expensive endeavor in which large corporate entities, or subsidaries, normally are directed and staffed by highly trained exploration specialists. In some instances consultants, with expertise in a given field, are utilized to the benefit of such corporate groups. The "grasshopper" approach to exploration-searching only for outcropping minerals and/or investigating only mineral prospects offered by the discoverers of such outcrops has given us most of the past and present mines in the US., but this method is rapidly approaching the point of diminishing returns in areas that have been thoroughly prospected for currently marketable commodities. With

Jan 1, 1973

By D. M. Loring

Radon progeny have been a health and safety concern for miners since the mining of radioactive minerals began. Through the ?nuclear age?, it has become better understood and the regulations have become more robust. Ventilation and control practices have improved, thus reducing miners? exposures. This paper provides an overview of radon in mining, the progress of the regulations, and discusses some of the uranium miner studies that contributed to the knowledge of the pathology of radon.

Jan 1, 2009

By W. H. Langer

Natural aggregate is the number one non-energy mineral resource in terms of value and volume and is a necessary commodity for sustainable communities. While aggregate is a non-renewable resource, supplies are nearly inexhaustible on a global scale. Natural aggregates have characteristics that differentiate them from most other mineral commodities: a high number of potential extraction sites, a high volume to value ratio, significantly different set of potential environmental impacts, and regional importance combined with a narrow economic transportation radius. Because of these and other differences, resource management policies for aggregates should differ from ?general? mineral resource policies, even though the end goal is the same for both ? ensuring sustainable resource management. To achieve the goals of sustainable aggregate management each stakeholder ? government, industry, the public, and non-governmental organizations ? will need to accept certain responsibilities, one of the most important of which is to become informed about natural resource issues. Sustainability is about making trade offs among competing objectives, and people disagree about the appropriate balance among the goals of economic prosperity, social equity, and environmental health. One of the primary purposes of mineral indicators is to provide information to decision makers and the public so as to ensure that the public debate about policy choices is grounded in fact. We identify the unique aspects of aggregate resource management and introduce the concepts of sustainable mineral resource management. We then present mineral indicator sets for aggregate resources from Italy, the United Kingdom, and Slovenia to demonstrate that effective mineral indicators should be specific to the resource in question and the public values and objectives.

Jan 1, 2003

By David Kress

Grinding mills, both autogenous and ball can be powered by several basic means. The three methods used today are girth gear drives, gearless drives and trunnion coupled reducers. This paper will focus on the first of these methods -girth gear drives. The girth gear drive has been used on thousands of mills which continue to operate successfully. These drives are noted for their simplicity and low cost. In the past, the horsepower capacity of girth gears has been slow to keep up with the horsepower increase required by the mill builders, particularly since the advent of the SAG mill. Gear manufacturers had capacity for 2000 HP mills in the 1950's, 5000 HP in the 1960's and 6500 horsepower in the 1970's. The 70's and 80's brought dual pinion girth gear drives which allowed mill sizes beyond 10,000 horsepower. Gear manufactures who could not keep up with the pace of the horsepower demands and the quality and reliability demanded by the mill builders and users have fallen by the wayside.

Jan 1, 1991

By Milton F. Searl

Introduction The urgency of further development of our domestic energy resources becomes more apparent every day. The production capability of existing facilities, taken in the aggregate, declines perhaps 10% per year; imported energy is expensive if available at all; conservation helps reduce demand but eventually will reach a point of diminishing return; new energy sources are promising but past experience, as with nuclear power, teaches us lead times are long and success is not assured. To approach the energy future rationally, it is essential to have some idea of the size of the nation's remaining energy resources, their characteristics, and the degree of uncertainty involved in their estimates. Resources are, of course, only one end of a long chain leading to energy supply to the ultimate consumer. They are an essential element, however, and the only one not under society's control. Given that the resources and a national will to produce the energy exist, it is possible to convert the resources to supply in, generally, an environmentally reasonable manner. However, the process of developing supply takes time. Government must permit access to the resource, and remunerative prices and further evolution of technlogy are required. This paper does not deal with these essentials, but they must not be forgotten. This discussion is limited to coal, oil, natural gas and gas liquids, uranium, and oil shale. Other energy sources are discussed elsewhere in this issue. Crude Oil Conventional crude oil resources are of greatest concern today, given our dependence on imported oil and its rapidly rising price. Estimates of oil originally in place (OOIP) range from 619 billion bbl to 1,094 billion bbl, differing by almost a factor of two (Table 1). This is surprising because the U.S. is a mature petroleum province with over 120 billion bbl produced and over 400 billion bbl OOIP discovered. Differences in the estimates involve differences in the experience of the various estimators, the interpretation of present geologic information and historical statistics, the methodology, and probably the extent (i.e., water depths) for which offshore resources are included. The range shown for the estimate of a given estimator appears to be primarily due to geologic uncertainty. This uncertainty can be measured by taking the ratio of the low and of the high estimate to the expected estimate for that information source. The low estimates range from 0.85 to 0.87 of their respective values. The high estimates range from 1.18 to 1.27 of the expected values. In all cases the high estimate is further from the expected value than the low,

Jan 1, 1980

By J. R. Knudson

A major contribution to the art of blasting was made at the Cleveland- Cliffs Iron Company?s Hawkins Mine in Cashwauk, Minnesota during April of 1956. It was here that the first experiments with fertilizer grade ammonium nitrate were conducted-experiments which led to the development of the ammonium nitrate and fuel oil method of blasting which has been eagerly adopted by open pit and quarry operators throughout the United States. While this new blasting agent was a more or less natural outgrowth of the Akremite Process devised by Maumee Colleries of Terre Haute, Indiana; no one, to our knowledge, had used this particular combination of ingredients prior to this time. Certainly this was a "break-through" as far as the Lake Superior District was concerned. Akremite consists of a mechanical mixture of grained ammonium nitrate and a solid carbonaceous material packed in a plastic bag. At the time of its introduction to the Mesaba Range, Akremite sold for 10.5 cents a pound as compared to the 18 cent powder previously used in both wet and dry large hole blasting. The discovery of this agent was indeed a remarkable achievement, one that afforded a substantial reduction in blasting costs. However, Akremite proved to be only an intermediate step in the evolution of our present low cost explosives. Cleveland-Cliffs utilized prilled ammonium nitrate and fuel oil and then eliminated the mixing and packaging plant entirely by combining the two raw materials in the field at the drill hole collar or in the hole itself. Thus we have approached the ultimate in simplicity, for the blaster and his helper now manufacture their own explosives not only as they are needed but where they are needed, and at a cost of under 4 cents a pound. This two-man crew may charge and explode as much as 8 tons of ammonium nitrate in an eight-hour shift and in so doing break some 65,000 tons of ore.

Jan 1, 1959

By J. S. Peterson, G. P. Cole

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Center (PRC), has conducted research to improve electrical fault detection on coal mine direct current (dc) trolley systems. Present circuit breaker protection systems are current-magnitude-based and cannot discern between normal traffic and high resistance electrical faults. Tests were conducted at cooperating mines to assist in developing a neural-network-based detection algorithm for distinguishing between electrical faults and normal operation. The Fast Fourier Transform of the trolley rectifier current signature served as baseline data for the neural network. During field tests, the algorithm performed with greater than 90% accuracy.

Feb 24, 1997

By J. Donovan Jacobs

Many improvements in the art of underground excavation have appeared during the past two decades. These improvements have been both in methods and in machinery and have resulted in more economical construction of today's tunnels. In the realm of machines, the developments of continuous boring heads for either soft ground or rock, random arm excavators and the sliding tunnel floor (Magic Carpet) have each made contributions toward more rapid tunneling. CONTINUITY OF ADVANCE Tunnel boring machines are often referred to as "continuous excavators". Continuous advance (without cyclical interruptions) has not been achieved, however, in any of the machines now in use. In most rotary-head tunnelers the thrust needed to make the cutters bite into the face is obtained from hydraulic cylinders reacting against anchoring devices held stationary by pads which grip against the sides of the tunnel. With this system the forward motion of the cutting head is continuous only until the propelling cylinders have reached their limit of extension. At this point the grippers must be released, moved forward and reset before a new cycle of advance can be begun. Some machines are built to obtain their propelling thrust from hydraulic cylinders pushing backward against newly-installed rings of tunnel support. This is the customary method for propulsion of shields. With it, each cyclical advance or "shove" must await the erection of a new ring of supports. Faster tunnel driving

Jan 1, 1974

By Zengwu Zhao, Peng Xu, Jieliang Wang, Qingwei Bai, Xinyang Liu, Xiao Lei

The paper investigates the capture and recovery of rare earth minerals from Bayan Obo ore using superconducting magnetic separation. A finite element model (FEM) was established to study the influence of various factors on the capture of rare earth minerals under a high-gradient superconducting magnetic field. The study aims to improve the efficiency of rare earth mineral separation and recovery.

Oct 1, 2023

By N. I. Jayaraman

Dust scrubbers on continuous miners are steadily gaining in popularity. Recent Bureau of Mines research on scrubbers is reviewed, with emphasis on the following areas: * Development of a new type of water-powered scrubber which can be retrofitted to existing miners. * Comparison of scrubber effectiveness with blowing and exhaust line ventilation. * Improving the quartz dust collection of flooded-bed' panels.

Jan 1, 1989

By H. N. Dougherty

"The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) ventilation gallery was used to study methane-air flows around a continuous miner mockup with water sprays and a scrubber fan. Methane gas was released from pipes located at the face to simulate face gas emissions. Methane concentrations and air velocities were measured while varying parameters such as airflow quantity, entry width (sump or slab cut), and face ventilation configuration (blowing or exhausting curtain). Test data showed a similar pattern of methane concentrations at both low and high airflow quantities, but a difference in the distribution of methane concentrations between narrow and wide entry widths. Most tests showed that blowing face ventilation was more efficient in diluting methane than exhausting ventilation, similar to observations made in previous empty gallery studies. The patterns of airflow and methane concentrations observed in this testing can further improve the understanding of airflow in and around the CM and face, promoting effective use of face ventilation to improve the health and safety of miners. INTRODUCTION Attaining an accurate understanding of airflow distribution at the continuous miner face is instrumental in maintaining a safe mining environment. US mining regulations require that sufficient airflow must be directed to the deepest penetration of the face and render harmless contaminant gases, as verified by the Mine Safety and Health Administration (MSHA). Currently, continuous miner face air readings can be taken in the last open crosscut and at the inby end of the curtain mouth. By measuring adequate airflow in a pre-determined area it is accepted that a sufficient quantity of that air exists to sweep the face of harmful dust and gasses. Unfortunately, due to the location inaccessibility, precise face velocity readings cannot be measured in situ. Face velocities may be estimated through computer-simulated programs based on laboratory models. Improving upon previous empty gallery testing and to more effectively determine representative face methane readings, a mockup of a continuous miner with water sprays and a scrubber fan was used in the current study to further refine face airflow conditions that would be closer to actual mining conditions."

Jan 1, 2016

By P. Zhang

The use of phosphate depressants in the cationic flotation of silica from francolite in the Florida phosphate industry is rarely practiced. The occasional use of gelatinized starch derivatives and pH adjustments to assure a slightly alkaline flotation feed slurry pH have been used in some processing plants to improve selectivity. This paper presents a preliminary laboratory comparison of several potential phosphate depressants for use with the flotation of siliceous phosphates. It was found that starch is ideal for floating fine (-35 mesh) silica from phosphate, while sodium tripolyphosphate may be the best for coarser (+35 mesh) feeds.

Jan 1, 2009

By William A. Hustrulid

The subject of surface mine development is large. This section covers the fundamental concepts involved in both the open pit mining of thick or steeply dipping deposits as well as the strip mining of thin, shallow, and relatively flat-lying seams or beds. Design involves the marrying of geometries, ore and waste characteristics, equipment, and economics so that the desired result is achieved. Generally, there are many possible combinations from which to choose. For example, extraction over a short time period requires one strategy while quite another is applied for longer times. Variations in supply and demand require some flexibility of operation. Customer requirements impose certain constraints regarding the set of possible designs. Over recent years, planning and operating considerations for surface mining imposed by environmental requirements have increased markedly. There have, at the same time, been enormous advances made in the design aids available to the mine planner. Computer simulation of the various options, whether it be for mine design or equipment selection, provides detailed information for decision making in real time. A significant challenge to the engineer/planner is how to best use the aids avail-able. Because of the widespread use of commercially available and in-house computer software by industry, this section does not deal with the details of planning (for basic coverage of mine development, see Section 7). Rather, some of the basic concepts are stressed. The principles involved in equipment sizing and selection are discussed. A highly important but sometimes over-looked aspect of planning, haul road design, is also covered. For surface mining operations of the future, in-pit crushing and conveying will become even more important. Some of the considerations for application evaluation are included. The section concludes with some future concepts for surface mining.

Jan 1, 2008

By Chas. E. Shumate

There is assembled here this morning in Chicago the heartland of America, what is undoubtedly the greatest concentration of Technical, Scientific and "CAN DO" knowledge ever assembled in America. The participation in this Conference by the representatives of so many nations is particularly impressive and is a further indication of the importance of the subject matter of this conference which you will be discussing in much detail during the next few days. Another impressive feature of this Conference is the participation of a large segment of the construction industry in whose hands fall the job of building what others design. Also strongly represented is the manufacturing industry whose capability is well known throughout the world. They have the resources to design, develop and manufacture the machines and specialized equipment needed to do any job which the world requires. You should not expect to gain any knowledge from my few remarks this morning as I am undoubtedly the least qualified individual in this room on the highly technical and scientific subjects you will be discussing during these next few days. However, I shall offer a few broad suggestions on subject matter which I trust may generate serious thought during your discussions.

Jan 1, 1997

By Rohan Fernando, David P. Snyder, John F. Burr, Susan M. Moore

"The Mine Improvement and New Emergency Response Act of 2006 (MINER Act Public Law 109-236) was passed by Congress in response to three major underground coal mine accidents in the United States that claimed the lives of 19 miners. The Act resulted in substantial changes in the underground coal industry relative to the use of technology for mine escape, rescue, disaster response and other areas where the lack of these technologies contributed to the fatalities caused by these tragedies. This year marks the 10th anniversary of the MINER Act, which makes it an opportune time to reflect on the events that led to its passage, the changes that have been made since then, and the work that remains to be done.As discussed below, the last decade has demonstrated tremendous cooperative efforts among mining operators, technology innovators, labor, The National Institute for Occupational Safety and Health (NIOSH), the U.S. Mine Safety and Health Administration (MSHA) and state regulators, resulting in substantial improvement of the technologies used for escape and rescue and noteworthy progress toward meeting many of the goals of the MINER Act. While the MINER Act and this article pertain primarily to coal mining, many of the technologies are equally applicable to any underground mining and have already found some acceptance outside of coal.Technology gaps targeted by the MINER ActThe MINER Act addressed several technology challenges:• Problems with donning and switching between self-contained, self-rescuers (SCSRs).• Poor visibility in smoke.• No wayfinding assistance for escape from the mine.• Limited breathable air supply.• Inability to locate trapped miners.• Inability to communicate with trapped miners.• Failure of mine seals."

Dec 1, 2016

By Norman M. Junk

Following the wide-spread acceptance of ANFO as a useful, low cost blasting agent, studies have been made to adequately describe the physical and explosive properties of this material (1). As the quality of the AN blasting prill improved, reliability and sensitivity to initiation were greatly increased and many methods of priming were chosen from the standpoint of economics with little appreciation for the need to initiate so as to obtain the most efficient detonation. Under certain conditions, ANFO could be initiated with primers no more powerful than a No. 8 blasting cap (2). Research on primers for ANFO followed and it was demonstrated that this blasting agent was subject to extreme transient velocities upon initiation with wide variations in energy output depending upon the nature of the primer. For these reasons it was shown that powerful priming was economically justified (3). These studies helped to define the properties of an effective primer and the guides for its efficient use. In the vast surface coal mining industry, technological advances in earth moving equipment were paralleled by the development of larger and larger borehole drills (4). Even though ANM) was the major blasting agent used in this industry, investigations of priming techniques in these larger boreholes was almost non-existant. In 1962, Mr. Cleon Woolsey of Enos Coal Company disclosed to the industry that dramatic improvements in blasting production could be achieved with new priming and boostering methods (5). The research program at the Atlas laboratories was designed to explain these results and extend the study of initiation of ANFO with both high explosives and slurry explosives and to define the principles involved.

Jan 1, 1968

By Thomas P. Goslin

T e mechanization of industry to reduce labor costs and to improve product quality is affecting he scale industry as it has affected many other industries. With increased emphasis on higher production rates many operators are experiencing difficulty in overcoming production problems where weight is a factor. Unfortunately, the scale industry has not shown the development over the last twenty-five years that other instrument industries have. For centuries the balance scale has been the standard and the workhorse of most weighing operations. In recent years considerable effort has been applied to designs to make balance scales more acceptable to industries employing automatic or semi-automatic processes. For the most part the designers have not attempted to replace the basic scale but toautomate functions of material handling and human judgement. Modern dump scales, for example, will accept material from a conveyor until a preset amount of material is on the scale, At this time the scale turns off the conveyor, dumps the load of material and repeats the operation with any desired timing. These improvements have helped industry. Even the scale observer has been replaced with devices which observe the scale reading and operate on weighed objects according to their weights. In spite of' the application of automation to the material handling, the balance scale has not been completely satisfactory. One reason for this is fairly evident when one considers the construction of the scales. Inherently, they are slow devices because of the inertia of the beams. The beam scale, primarily a static measuring device, is at the best limited to slow dynamic measurements.

Jan 1, 1958

By W. R. Hail

A proactive design and construct approach was used to remediate the Warm Springs Ponds Complex near Anaconda, Montana under "Superfund". The pond complex is used for treatment/settlement of heavy metals and is a repository for 19,000,000 cubic yards of tailings, precipitates and associated sediments. Remediation has resulted in treatment/settling capacity for flows up to the 100-year flood (3,300 cfs); expansion from 5 to 11 ponds in series requiring 12.5 miles of new or improved embankments with associated hydraulic structures; flood protection for the 0.5 Probable Maximum -Flood (PMF) (70,000 cfs); and closure of exposed tailings along with aquatic and terrestrial habitat enhancement.

Jan 1, 1995

By Fouad Faraj

For every blast pattern, zones of unique material types need to be classified before mining. Most material types can be summarized into different kinds of ore and waste. Blocks generated from blasthole assays are too small to be selectively mined so areas with a single material classification meeting the mine’s selective mining unit must be defined. Current industry standard practices are to manually draw ore/waste dig limits but this process is subjective and results in quantities of dilution and ore loss which can be improved upon to enhance the profitability of mining operations. Two weeks production data from a homogeneous Cu porphyry and heterogeneous Manto-type Cu deposit are used to assess the variability in the hand-drawn dig limits for 20 geologists, mining engineers, or ore control specialists and are compared with the optimal ore/waste delineation. The profit for 20 distinct hand-drawn dig limits for the homogeneous mine ranged by 3.7% from $10.5 million to $10.9 million averaging at $10.8 million. The percent range nearly doubled for the more heterogeneous mine at 5.9% from $17.9 million to $19.0 million averaging at $18.6 million. Using the optimal ore waste delineation, the profit increased to $11.0 million (1.9% increase) and $19.3 million (7.0% increase) for the homogeneous and heterogeneous deposits respectively. The natural variability, diggability requirement, and selectivity are identified as the main drivers of ore loss and dilution. Recommendations are provided for reducing the subjectivity in manual hand-drawn dig limits by integrating dig limit optimization algorithms as a tool to assist practitioners.

Feb 23, 2024

By S. K. Bhoumik, D. K. Sengupta, B. P. Singh

This paper deals with experimental work to improve the settling and filtration characteristics of an industrial sludge from an iron-ore mine using synthetic polymeric flocculants. The experimental work consisted of the characterization and evaluation of suitable flocculants to enhance settling and filtration rates. The optimum dosage of the flocculants were determined. The experimental results revealed that the settling rate can be increased many times, compared to untreated sludge, by using a suitable combination of flocculants. Compared to cationic and nonionic flocculants, anionic flocculants were found to be more efficient in sludge flocculation. The synergistic effect of two anionic flocculants produced the best settling conditions. Filtration test results also reveal that suitable flocculants can improve the dewatering characteristics of the slurry.

Jan 1, 1997