Search Documents

By Franziska Wolf, Rainer Ellmies, Helmut Mischo

"Mining is an important part of the economy of Namibia. In 2016, 11.1 percent of the GDP was the result of mining activities with 22 active mines (The Chamber of Mines of Namibia, 2016). Only one of them consists of an underground mining operation.The global annual production of fluorspar is approximately 5.4 to 6.3 Mt (6 to 7 million st) (U.S. Geological Survey National Minerals Information Center, 2017). Okorusu has produced on average about 45 kt/a (50,000 stpy) in recent years (U.S. Geological Survey National Minerals Information Center, 2015).The Okorusu Mine is Namibia’s only fluorspar mine. Fluorspar was mined in an openpit mine with four individual pits (A-D) since 1980. In 2014, the mine closed due to the increased stripping ratio and beneficiation problems. The mine assets were bought by Gecko Namibia. Currently, Gecko uses parts of the processing plant for beneficiation of graphite from a neighboring mine. Figure 1 shows a panoramic view with the four pits and the mine village.The intent is to develop a concept for the further underground development of the mine. There are still about 6.3 Mt (7 million st) of measured resources left in the deposit, with an average grade of 27.5 percent CaF2. This study focuses on the underground mine design. The above-ground plant and facilities are considered as remaining unchanged.For solving the task to design the mine, a site visit for data collecting was conducted. Resource estimations were calculated based on existing drill data, and consequently, block models were created. The development of the mine design included the selection of the most suitable mining method, mining technology and mine organization. Moreover, some economic considerations are pointed out, followed by a profitability assessment."

Jan 2, 2018

By M. Fan

Coal has in general a wide range of density from minus 1.3 to plus 2.0 g/cm3 because of its variations in purity, rank, and porosity, etc. The coal density has great impact on froth flotation performance, but much less attention has been paid to particle density than particle size. Our previous research results demonstrated that cavitation-generated nanobubbles around 700 nm in diameter can significantly improve coal and phosphate flotation performance over a wide particle size range. In this study, the effect of nanobubble on the flotation performances of different density fractions (minus 1.3, 1.3-1.4, 1.4-1.5, 1.5-1.6, 1.6-1.8, 1.8-2.0, 2.2-2.2, and plus 2.2 g/cm3) of coal was investigated using a bank of 10-liter flotation cells, a specially designed 50-mm-inside-diameter column, and a 152-mm-inside-diameter column. It was found that nanobubble has the biggest impact on the flotation performance of 1.4-1.8 g/cm3 medium-density coal particles.

Feb 23, 2014

By Luzheng Chen

The study aimed to evaluate the separation performance of a full-scale continuous centrifugal concentrator in the reconcentration of fine hematite from high-gradient magnetic separation (HGMS) concentrate in a tailings recovery plant, and to investigate the usefulness of the technology in industrial applications. The effect of changing the operating variables on concentrate grade and recovery was studied. The results indicate that among the variables considered in the study (water spray pressure, centrifugal acceleration, feed volume flow rate, feed percent solids and the reciprocation and spacing of water sprays), the change in centrifugal acceleration affects the recovery the most and continuous concentration can be achieved only when the water spray has a sufficient pressure. In addition, the reciprocation and spacing of the water sprays have a significant influence on the concentrate grade. Although performance of the full-scale concentrator is slightly inferior to pilot-scale trials, due to limitations in the scale-up design and the fluctuations of feed material characteristics, this concentrator provides a potential way to achieve continuous concentration and obtain a high-grade concentrate from tailings.

Jan 1, 2010

By N. G. W. Cook

The conventional cyclic system of deep-level mining by drilling and blasting gives rise to an inadequate degree of stope sorting when mining thin reefs. This results in poor utilization of the capital facilities of a mine in the form of shafts, haulages, airways and associated equipment. Continuous and controlled removal of the thin gold-bearing portion of the reefs would permit better stope sorting and hence greater utilization of capital facilities. Results of experiments to develop hard rock cutting machines for mining are reported and the benefits which could be derived from their use are discussed.

Jan 1, 1969

By Fengyu Ren, Kunpeng Yu, Gideon Chitomb, Qiangqiang Gao, Liqiang Ma, Jiangtao Zhai, Ichhuy Ngo

The penetration of rock fragments of overlying strata causes advanced ore dilution during drawing. The results of numerical and physical experiments showed that the proposed numerical simulation was applicable and the microscopic parameters of the model were reliable. The penetration under the variables of particle diameter ratio, density ratio, overlying strata thickness, and particle morphology was clarified. The penetration was quantitatively characterized by the discharge amount and the dilution rate. The experimental results showed that the diameter ratio and density ratio had a significant influence on the penetration. On the irregular shape of particles, the penetration is weakened. The overlying strata thickness had little effect on the penetration. This study could provide a theoretical basis for the full section uniform drawing, avoiding advanced ore dilution and further optimization of recovery rate.

Nov 13, 2023

By R. W. Waytulonis

This paper is an update of the activities of the U.S. Bureau of Mines, other government agencies, and the automotive and truck industry concerning diesel emission control. Enacted and proposed regulations from the U.S. Mine Safety and Health Administration (MSHA) and developments in diesel emission control are presented in terms of their impact on underground coal, metal, and nonmetal mines. Mine air quality regulations proposed by MSHA may require the underground mining industry to comply with new standards. Some mines may be required to take additional actions to meet new diesel particulate and lower nitrogen dioxide exposure standards; however, the mining industry is in a position to benefit from emission controls developed for the on-highway diesel engine market. The U.S. Environmental Protection Agency (EPA) has enacted regulations to reduce emissions from on-highway diesel trucks and buses. Engine manufacturers have responded by developing cleaner burning engines. Fuel producers have responded by providing cleaner burning reformulated diesel fuel, and exhaust aftertreatment devices have been developed to provide additional emissions reductions. Bureau research and development projects seek to determine the advantages of using modern engines and fuels, and to evaluate the efficacy of new exhaust control devices on mining machines. It appears that the diesel engine will continue to be a practical power source for use in confined environments because no other available power source is as mobile and efficient.

Jan 1, 1993

By Clinton Birch

The multiple-criteria decision analysis is a technique that helps to find an optimal solution by evaluating conflicting criteria. In this study, an approach to perform multiple-criteria decision analysis for cut-off grade optimization, which considers the diverse stakeholder groups prevalent in the mining industry, is presented. The optimization model developed in this approach links the resource block model to the financial model, enabling the process to either maximize profit, net present value, revenue to the State, or extend the mine's life. To identify the optimal cut-off grade in each case, the Excel Solver function is utilized. Although it has limitations, the Solver function can still be modified to handle models with thousands of block values for determining input variables based on the target value. Following stakeholder engagement and dialogue, a single weighted average cut-off grade can then be determined. This approach is demonstrated for nine South African Witwatersrand gold mines.

Jun 25, 2023

By A. Bruynesteyn

I would like to talk to you today about microbiological leaching or, the solubilization of metal values due to the action of Thiobacillus ferrooxidans. Bacterial attack of sulfide minerals has been going on for centuries but only recently was it discovered that the acid and iron often found in coal mine drainage is produced by bacterial action on the iron sulfides in the coals. Not until 1950 was it proven that bacteria were playing a role in the dump leaching of sulfide ores. B. C. Research became involved in microbiological leaching in 1955 while examining mine drainage from the copper-zinc mine at Britannia Beach, north of Vancouver. Since 1955, B.C. Research has maintained a continuous re¬search program on microbiological leaching which, due to its applied nature, was put under industrial sponsorship in 1962. Most of the information pro¬vided in my talk today has been gathered under this sponsored research program and I would like to express our appreciation to the many sponsors who have made our work possible.

Jan 1, 1970

By Kenneth Savidge

With the recent demand for increased coal production there has been a corresponding increase in the horsepower of the shearing machines. The resultant increase in the machine haulage pull has heightened the incident of haulage chain breakage resulting in machine downtime, but more seriously the danger to face personnel. This paper discusses the application of chainless haulage to longwall mining and describes the systems currently available.

Jan 1, 1978

By R. L. Stone

By means of laboratory balling tests and a procedure for determining bentonite concentration in a green ball the present study revealed that the bentonite savings by mulling concentrate and bentonite prior to balling was sufficient to warrant installation of a full-size unit in a pellet plant. On the basis of this work, a muller was put on stream at Bethlehem Steel Corporation's Cornwall pellet plant in June 1969, and has operated continuously since then. Plant tests showed that the use of the muller resulted in bentonite savings of about -502 without any loss of green, dry, and fired ball quality. Virtually no maintenance problems have been encountered. This information is important to future pelletizing operations both from the standpoint of product quality and economics.

Jan 1, 1971

By R. A. Meyr, K. A. Perry

Following three major mining accidents in 2006, the MINER Act of 2006 was enacted by the U.S.Congress. The U.S. Mining Safety and Health Administration subsequently released the Final Rule on Refuge Alternatives for Underground Coal Mines, which required every underground coal mine to install refuge alternatives to help prevent future fatalities of trapped miners in the event of a disaster. The following paper documents the research that was performed on a structural wall to be used in conjunction with a breathable air system to create a refuge alternative. A 103.4-kPa (15-psi) safe haven polycarbonate wall for use in underground coal mines was designed and modeled using finite element modeling in ANSYS Explicit Dynamics. The successful safe haven wall design was modeled for an actual underground coal mine environment using the explicit finite difference formulation program FLAC3D to determine the responses of the wall and surrounding strata within a mine. A full-scale design was fabricated and installed in an underground coal mine to determine any construction constraints and as a final step in proof of concept for the safe haven wall design. This paper is meant to introduce the reader to a new wall concept to be used in conjunction with current technology.

Jan 1, 2013

By E. R. Hendrickson

About 1/3 of the world's supply of phosphate rock is produced in a relatively small area of the Florida peninsula east of Tampa. Until this past year, a circle with a radius of about 25 miles and centered on Bartow would encompass the major producing areas. During the past year producing areas have opened in North Florida which promise to vie with the Polk-Hillsborough County area in terms of proven reserves. In addition, new phosphate production is planned for counties to the south and west of the present fields. From the existing production areas, however, more than 19 million long tons of phosphate were mined in 1965. As mining engineers most of you probably are familiar with the methods of mining and beneficiating the pebble phosphate rock. You thus recognize that, although some water quality problems may arise from these processes, there is no potential air pollution problem. To make an economically useful product, however, further processing must take place. It is from this additional processing that potentially damaging materials may be discharged to the atmosphere.

Jan 1, 1966

By V. K. Reddy Kallam, NEHA PANDEY, Sunil Kumar Tripathy, ARIJIT BISWAS

The study investigates SO2 leaching of low-grade ferruginous manganese ores to selectively recover manganese as MnSO4 and produce battery-grade electrolytic manganese dioxide (EMD). The effects of leaching parameters (duration, temperature, SO2 flow rate) on Mn recovery were studied. Under optimum conditions, 97.9% Mn recovery was achieved. The MnSO4 leach liquor was purified and used for electrowinning EMD with 88.01% purity and battery-active γ structure.

Apr 20, 2022

By Steve Kral

Through advanced technology and innovative thinking, the mining industry has become one of the world’s leading industries in environmental protection. But it only takes one Summitville, Omai or, most recently, the Aurul gold tailings retreatment operation in Romania to provide ammunition to the industry’s critics in their attempts to sway public opinion against mining. So for the mining industry to continue operating with the public’s support, it must continue to improve its tailings waste-disposal processes and the dams that hold this waste. In January, about 120 specialists in the mine waste management field gathered together to discuss the available technologies and materials for controlling mine waste and mill tailings disposal. “Tailings and Mine Waste’00” was held at Colorado State University in Fort Collins, CO. This meeting, begun in 1978, is a continuing symposium. It provides a forum for environmental professionals to discuss the state-of-the-art in mill tailings and mine-waste disposal methods.

Jan 1, 2000

By Sebastian Avalos, Julian M. Ortiz

The long-term mine scheduling is the optimal decision on how to extract and process the mining reserves. The resulting plan is mainly driven by economic, metallurgical, and geological factors. Accounting for their uncertainties leads to a robust solution and the feasibility for economic-risk quantification. In this work, we model the spatial uncertainty of grade distributions of multiple correlated elements, by using a multivariate morphing transformation. The result is a set of multivariate geostatistical realizations of the grades, which honor the conditioning data, the direct and cross variograms, and the multivariate statistical distribution, inferred from a set of samples. These models are the input in a reinforcement learning framework, adopted to train a deep neural network that considers the grade uncertainty and leads to an optimum mine plan after training using deep Q-Learning. Mining and processing capacities, as well as economic parameters and metallurgical constraints, are incorporated as the reinforcement learning environment rules. The method is validated on a real deposit, providing insights for future applications.

Jun 25, 2023

By Elisa Comis, Barbara Bitetti, Julien Pepiot, Stefano Lione, Francesc Rich

The new Lyon-Turin railway project involves the construction of a 57 km twin-tube tunnel between France and Italy. Pini France (project leader) and Systra-SWS are the designers of Construction Site 8 (CO8). This part of the project includes the construction of the tunnel portal on the Villard-Clément platform, two 2.8 km long tubes of the base tunnel in the direction of Saint Martin la Porte, the cross-passages between tubes and the niches. This paper presents the general approach followed to design the temporary support for the base tunnel, cross-passages, and technical rooms. The design of the temporary support accounts for the variability of the ground and water conditions, the excavation attended behavior, the construction planning and the identified geological hazards that could be encountered along the alignment. Particular attention is paid to the intersections between the tunnels both in terms of numerical modelling and construction methods and phases. Two types of intersections are present in the project: the intersections between the cross-passages and the base tunnel and the intersections between the base tunnel and the niches. 3D models have been developed for the tunnel intersections.

Jun 23, 2024

By Margreth Tadie, Chalwe Chibwe

Physicochemical properties of copper electrolytes are a strong fundamental consideration in electrodeposition processes during electro-purification and recovery of copper. Their influence extends to mass transfer as well as energy consumption during the electrodeposition process. In this study, the influence of electrolyte composition on electrolyte physicochemical properties was investigated to review the existing literature data. This review of data is considered necessary as more and more electrowinning models are being developed for process prediction and optimisation and a need of such data is required for accurate prediction of physicochemical properties. The major components of importance to the formation of smooth high-quality and high-purity copper cathodes at optimum current efficiency are considered the species in solution. These include Cu ions, Fe ions (major impurity), H2SO4, and a smoothing agent additive. A 5-factor, 2- and 3-level experimental design was employed to determine the effect of copper (35 and 45 g/l), sulphuric acid (160 and 180 g/l), iron (1, 3, and 6 g/l), polyacrylamide additive (2, 5, and 10 mg/ l), and temperature (45 and 55 °C) on electrolyte density, conductivity, and the diffusion coefficient in synthetic copper electrowinning electrolytes. The major species in a copper electrowinning electrolyte are found to be the most relevant for prediction of physicochemical properties. These results indicate that relatively simple empirical models are sufficient for modelling of the electrolyte domain in electrowinning, without the need for the generation of vast amounts of complex experimental data.

Feb 1, 2021

By J. Kalliokoski

As part of a funded project we have completed a comparative literature survey of the US regional Proterozoic geology. For our com¬parative study model we used the geological settings of the very large pitchblende deposits in Saskatchewan, Canada and the Northern Terri¬tory of Australia. These occur in a variety of Archean and Lower Proterozoic host rocks, at and below a regional unconformity that is capped by subhorizontal Middle to Upper Proterozoic conti¬nental sedimentary rocks. We find that there have been recorded in some parts of the US similar unconformable sequences of Middle to Upper Proterozoic continental sedimentary rocks that overlie older basement rocks.

Jan 1, 1979

By J. E. Gebhardt, H. Toro, K. Y. Lee

Industrial-scale test results indicate superior metallurgical performance of column flotation compared to conventional cell flotation for copper cleaning. A technical comparison of bubble generation systems for column flotation is made. Two types of bubble generation systems are considered: the filter-cloth type spargers and the Turbo-Air® sparger, which utilizes an air-water mixture fed to the column through injection tubes. Examples of the improved technical performance available with an external sparger system are presented using data from plant tests conducted for specific applications with several different mineral ores. INTRODUCTION Column flotation is now a valuable unit operation which mineral processing engineers employ in the design and operation of flotation circuits in nearly all mineral applications. The acceptance of columns in the mid- 1980s by the minerals industry was paralleled by a rigorous approach to developing a scientific understanding of the design, scale- up, and operation of column flotation units (Finch and Dobby, 1990). Since then, column flotation has become a standard unit of the cleaning stage in many new mineral concentrator projects and has replaced older mechanical cells to improve process efficiency. The size of column cells has continued to grow from the initial 0.9- to 2.1 -meter diameter range, and it is not uncommon to find column cells today being 2.7- to 3.6-meters in diameter. With the success of the smaller units, the scale-up to larger cells has been proven and demonstrated by the performance of the large-diameter cells (Murdock and Wyslouzil. 1991). The use of columns in flotation circuits has also been accompanied by developments in modelling. control, and optimization of column performance (Lee et al, 1991). The bubble generation system is the heart of the operation of column flotation cells. The most common methods for generating bubbles can be divided into two types: the internal and external spargers. Internal spargers are typically a porous material, such as sintered glass, porous rubber or filter-cloth, or maybe a single- or multi-nozzle sparger. External spargers implies that a gas and a liquid (either water or slurry) are brought into contact outside the column and that mixture is then introduced into the column. Several types of external spargers are available today, and innovative designs for externally mounted air sparging systems have been a significant factor in the successful application of columns. Early types of bubble generation systems.

Jan 1, 1993

By J. A. Organiscak

Longwall mining technological improvements have provided significant increases in productivity over the last 15 years. Longwall productivity is anticipated to continue to escalate with expanded application of automated equipment. Automation technology that will likely be adopted over the next 5 years is memory cut with shearer initiation of shield movement supervised by a couple of face workers. Operations using this technology will most likely relocate many production workers from the face to the outby gate entries and position several face workers outby the shearer, exposing workers to different health and safety risks. These changing risks are primarily related to worker relocation and expected increased production levels. Workers outby the face will most likely have less dust and noise exposure, but will be exposed to other safety hazards associated with outby equipment movement, materials handling, and gate entry ground movements. The face workers will most likely be exposed to higher respirable dust and noise levels generated by the equipment at elevated production rates. Methane gas emission is also expected to increase with faster mining rates. These operational changes and the control technologies needed to reduce redefined longwall worker hazards at semiautonomous longwall operations require examination to maintain the health and safety of mine workers.

Jan 1, 1996