Search Documents

By D. W. Wu, M. T. Haque

A novel impedance probe has been commissioned specifically for capturing fast dynamic information about filtration processes. It provides an attractive alternative to more complex measurement techniques in situations where the slurry system is primarily one-dimensional. The probe can monitor mud-line, slurry densification and drainage. Dynamic variations in cake permeability are obtained by combining dynamic mud-line information obtained with the probe and filtrate rate data derived from a leaf test apparatus. The measurements are re-viewed in relation to micro structural measurements obtained on iron ore filter cakes. The practical significance of these measurements for optimization of the filtration process is discussed.

Jan 1, 2000

By Zach Ahinga, Mike McRae, Dave Hopkins, Steve Klein

The San Vicente Pipeline project involves the construction of an 8-1/2 foot diameter water pipeline in an 11 mile long tunnel in San Diego, California. The tunnel will be excavated in extremely variable geologic conditions consisting of strong granitic and metamorphic rocks, weak sedimentary rocks, abrasive conglomerates, and mixed face conditions. This paper discusses the challenging geologic conditions and some of the key design evaluations for the project. Currently design work for the project has been completed and construction will be underway by mid-2005.

Jan 1, 2005

By J. K. Whyatt

A microcomputer controlled data acquisition system has been developed for automatic monitoring of underground instrumentation from a remote location. The system has been used extensively by Spokane Research Center personnel for monitoring rock instrumentation in shafts, drifts, and stopes in hardrock and coal mines, especially where instrument access is limited. Ruggedness was a major consideration in designing the underground portion of the system and it has performed satisfactorily under extreme environmental conditions, including temperatures to 1100 F, 100% humidity, and falling water. The major advantage of the system is that it multiplexes the data from 16 channels through a single twisted pair cable to the receiver, significantly reducing cabling requirements. This receiving station can be as far as 8,000 ft from the instruments without the addition of line drivers. The receiver maintains a data buffer with the latest scans, which is periodical 1 y accessed by a micro- computer, either locally or through a modem, that automatically records and reduces the data. Utilities allow on-site plotting of data and uploading of data to mainframe computers.

Jan 1, 1986

By A. J. Monhemius, S. Raghavan, G. W. Warren, E. Peters, D. W. Furerstenau

A lyometallurgical process for extracting copper from an ore containing chrysocolla by leaching it with a kerosene solution containing LM 63 in the presence of small amounts of aqueous ammonia is described. The experimental results indicate that 70 to 75 percent of the copper can be extracted from the ore using an ammonia content that is about one-fourth the stoichiomeaic quantity required to leach copper in an aqueous leaching system. The rate of copper extraction was found to be a function of particle size, ammonia concentration and temperature. The large quantity of physically adsorbed water together with ammonia in the pores of chrysocolla provides a mechanism for the transport of copper to the external surface of the particles where it is complexed by the LM molecules and transferred into the organic phase. When size reduction accompanies leaching, the extraction process was found to proceed when only "trace" quantities of ammonia are present in the system. The kinetics of the extraction process appear to be controlled by a mixed (reaction and diffusion) mechanism.

Jan 1, 1993

By Adrian Brown

Groundwater inflow and impacts have become major aspects in the permitting and operation of many gold mines. First, the hydrothermal or placer genesis of many of the orebodies being investigated or produced today almost guarantees that mines will be "wet", involving groundwater control as part of operations. Second, the style of ore deposition a1 so often involves a1teration of the host rock, resulting in relatively weak, low permeabi1ity materials that require extensive groundwater pressure control for stable mining. Third, the location of many mines in arid areas guarantees that impacts on water resources will be matters of key focus during permitting and operation. However, groundwater control and protection is a technically difficult area and often involves managerial decisions and activities that do not fit comfortably into traditional mining. In an attempt to overcome some of these difficulties, this paper provides a guide to mine managers and hydrologists as to appropriate strategies for designing, setting up, operating, and evaluating groundwater programs at gold mines that get the job done and are cost effective.

Jan 1, 1988

By Edmond Donovan, O&apos

With the increase in complexity of conveyor systems and the inexorable demand for more capacity and availability, the ability of designers to accurately predict performance is becoming increasingly important. Dynamic analysis techniques for modelling wave mechanics in conveyors are finding increased applications. Unfortunately, the reliability of these modelling techniques is dependent on a thorough understanding of the performance characteristics of the components that make up the system. These characteristics include such things as response rate, hysteresis and efficiency. Some parameters such as idler rolling resistance can be easily quantified by measurement. More complicated drive parameters are difficult or impossible to measure, particularly in large horse-power equipment. One method of quantifying or at least bracketing the performance envelope of complicated pieces of equipment is to construct a mathematical model. This can be done quickly and economically, and the influence of various parameters can be determined. This paper sets out to demonstrate by example the usefulness of this technique in gaining an understanding of complicated systems. The model is developed and the influence of a number of variables are examined.

Jan 1, 1996

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Variations of cut-and-fill stoping are the most com¬monly used methods for mining narrow, nearly vertical veins in the United States. These methods offer the best results for maximum recovery with minimum dilution of ore from veins that are irregular along either the strike or dip. The vein is developed along the strike length in 61 to 122-m (200 to 400-ft) blocks or stopes and vertical lifts of 48 to 61 m (160 to 200 ft). The level development is either on the vein or parallel to the vein with crosscuts intersecting the vein at right angles. Chutes, manways, and haulageways are established in the center of the stopes at the lower level of the ore block. Mining then proceeds by blasting down horizon¬tal cuts of the vein in both directions from the chutes. As the blasting continues to the outer limits of the stope, the broken ore is slushed into chutes. When a complete horizontal cut has been made, the service raise, including chutes, is raised to a height of a few feet from the back and the stope is filled with either sand fill or waste rock. Then the mining cycle is re¬peated until the stope reaches the level above. LEVEL DEVELOPMENT PRACTICES FOROVERHAND CUT-AND-FILL STOPING The two basic methods used are: the development of the haulage drift within the vein, or development of the haulage drift paralleling the vein in the foot or hang¬ing wall with crosscuts intersecting the vein perpendicu¬larly at 61 to 122-m (200 to 400-ft) intervals. The il¬lustrated methods of development show some of the variations which can be used to develop a stope block. Development for cut-and-fill stoping does not require the more elaborate schemes outlined for shrinkage or sublevel long-hole stoping. Many factors must be considered before deciding on a particular development plan and usually the nature of the vein or host rock will dictate which specific method to use. If the vein is relatively straight, then develop¬ment on the vein is feasible. Excessive ground pressures will necessitate the leaving of a sill pillar (Fig. la) and highly fractured or "heavy" ground will require timber¬ing (Fig. 1b). Development on the vein has the advan¬tage of reducing capital outlay and waste handling prob¬lems since the mined rock has value. But removal of the sill pillar is costly and time-consuming. Also, where no sill pillar is left, excessive timbering and subsequent level repair is a drawback. Development in either the footwall or hanging wall is the more common procedure and offers greater flexi¬bility in overall development of consecutive stoping blocks by partially disassociating the level development from stoping (Fig. 2). Chutes, manways, and service compartments com¬prise the next stage of development and are established in a variety of ways. They provide access to the stope, ventilation ducts, and muck removal. Several different development systems are in common use and average costs for each have been developed. Raise borers are used to establish ventilation and ac¬cess from level to level. They are normally reamed with 1.5 or 1.8-m (5 or 6-ft) cutterhead and may either be left bald or lined with a 1.2-m (4-ft) diam corrugated liner plate, depending upon ground conditions. The use of an Alimak raise climber is another effec¬tive method of driving a raise from level to level. The size usually is 2 m (7 ft) square. This will accommodate square-set timber which is later installed. This method of raising is not common, although it is a valuable tech¬nique especially when level spacing is several hundred feet.

Jan 1, 1982

By Z. Yu

Dewatering of a -0.5 mm fine coal has been studied extensively. Deep cleaning requires however fine grinding, and dewatering of such ultrafine products presents a great challenge. Several coal samples finely ground and characterized by different wettabilities have b.een used in the filtration tests. Vacuum and press filters have been employed. In this paper only the results obtained with different flocculants (totally hydrophobic. semi-hydrophobic and hydrophilic polymers) are included. The results reveal the effect of coal surface properties and flocculant type on filtration of ultrafine coal.

Jan 1, 1994

By C. R. Tinsley

Valuations can be molded, twisted and misinterpreted. Cases of spurious scope setting; limits to the information or access by the valuer; difficulties with the lack of comparative valuations; inappropriate valuation methods and outright speculations are described. None should be accepted by an experienced, independent minerals valuer. The Australasian Institute of Mining and Metallurgy (TheAusIMM) is working on a Valmin Code for which a Manual of Best Practice and Valuation Guidelines may be developed.

Jan 1, 1995

By W. H. Schiffbauer

The protection of miners, equipment, and infrastructure is discussed. While the primary focus of the described technology is to prevent miners from being injured, struck-by, or crushed by heavy equipment; another major benefit realized is also the protection of equipment and infrastructure. An attempt is made to define and classify the systems used to provide proximity detection and warnings as well as collision detection and avoidance. Information about the speed of vehicles and human operator response time can be a factor in the choice of what type of system and what features are needed to properly address the needs. How the technology adjusts to compensate for various vehicle speeds, while maintaining the same level of protection is noted. The statistics which justify the need of miner protection are provided. The primary system components required, what attributes they feature, and how they respond in the environment, is briefly highlighted. The physics behind the danger zone marker technology and what makes it so robust and reliable is established. Examples of a few mining applications and specific operational modes are provided for both surface and underground.

Jan 1, 2011

By D. Bradbury

Sufco coal mine, a subsidiary of Arch Western Bituminous Group, recently purchased a reverse osmosis (RO) system. The systems intent was to remove impurities in the water being mixed with the hydraulic oil to maintain the viability of critical longwall hydraulic systems and to prevent degradation. This project not only ensured hydraulic components from corrosion, but also revealed a cost savings by reducing the percentage of hydraulic oil mixed with the RO water. SUFCO WATER TREATMENT HISTORY Sufco coal mine has been in operation for approximately 70 years. Old works extend up to 15 miles one way, not including adjacent mined out longwall panels. Due to the geologic conditions and strata, water treatment has been as simple as putting water in at a high point of a mined out area and recovering it at a low point to discharge. Doing this reduces the total suspended solids (TSS) to less than 25 parts per million (ppm) and the total dissolved solids (TDS) less than 1,200 ppm which complies with Sufco?s water discharge permit. Even though the requirements for the permit were met, the water is still corrosive in nature. A portion of this water is piped back into the fireline (makeup) water system. It is then boosted to pressures of up to 500 psi to support mining sections, belt systems, equipment, fire fighting systems and the longwall.

Jan 1, 2011

By R. Pakalnis

A comprehensive project has been completed at the University of British Columbia that focused on the development of a commercially competitive composite cable bolt. Laboratory evaluation consisted of pull tests, preliminary shear tests, grout column testing and scanning electron microscope evaluation of the composite cable bolt. Field implementation at five underground mines throughout Canada were completed for technical and overall performance evaluation of the new product. The project began in 1989 under the sponsorship of HDRK Ltd., a consortium of mining companies including Inco, Noranda and Falconbridge Ltd. The objective was to develop a cuttable cable bolt that would serve as support for a continuous miner within a hardrock environment (Mah, 1994). The bolt was required to be cuttable by a continuous roadheader without adverse effects to equipment, personnel and the milling process. From the beginning, the focus was to employ existing cable bolt installation technology (Goris et al., 1994) whereby the cable bolts are grouted within a 4.8-cm-diam (1.08-in.diam) or larger employing a portland cement grout having a water:cement ratio between 0.35:1 to 0.4:1.

Jan 1, 1994

By Dana A. Echter

The Paso Diablo coal project is located in the Guasare Basin in the northwestern region of Venezuela near the border with Colombia. In 1987, Carbones del Guasare SA, a joint venture comprised of Carbozulia and A.A. Antilles Coal (an Arco and AgipCoal joint venture) was formed to develop the Paso Diablo coal reserves for world markets. Regional drilling has indicated a coal resource of more than 6 Gt (6.6 billion st). Further exploration has delineated the Paso Diablo deposit as an area particularly suited for cost-effective surface mining. The calculated economically minable reserves of this area (200 Mt or 220 million st) and the coal quality characteristics are based on extensive core drilling programs. Initial coal mining operations began in August of 1987 and the mine is presently producing at a rate of 1.5 Mt/a (1.65 million stpy). The coal is hauled about 85 km (53 miles) to a barge loading terminal at Santa Cruz de Mara using highway-type haul trucks. When the coal reaches the terminal, it is loaded into barges and then transloaded onto ocean-going vessels with barge mounted

Jan 1, 1990

By G. E. Viens

The electric arc furnace has characteristics which make it attractive for a number of metallurgical applications. Some of these characteristics are: high thermal efficiency, the possibility of attaining very high temperatures, low off-gas volume compared to fuel-fired furnaces, no impurities are introduced by the heat source, and impurities in only minor amounts are introduced by the electrodes. It also has disadvantages, the chief ones being the relatively high cost of electrical energy compared to fossil-fuel energy and the fact that, when oxide ores are smelted using carbon as reductant, the off-gases emitted are rich in carbon monoxide. As in many other pyrometallurgical processes, fumes and dust are emitted from melting or smelting operations. In many installations, some or all of the off-gases are flared, thereby wasting their energy and contributing to atmospheric pollution. During the last eight years, a shaft-electric furnace has been under development at the Mines Branch, Department of Energy, Mines and Resources, Ottawa, Canada. This project was initiated to try to overcome, or at least minimize, the disadvantages of the electric furnace. Experience on other projects, prior to the beginning of this program, had indicated that preparation of the charge materials, for example by sizing raw ore, sintering concentrates and crushing and sizing the sinter, or agglomerating concentrates into uniform-sized pellets, could make a substantial contribution towards achieving success in arc-furnace smelting projects; This entire

Jan 1, 1971

It doesn't take any special acumen to note that US engineering and construction firms are busier than ever with mining projects in this mineral conscious world. This special issue of Mining Engineering takes a look at E&C companies-their expanding role, their special capabilities, and their challenges and problems. ME sent a questionnaire to a representative sample of E&C firms. Information was sought about officers, ownership, and amount of business. ME also asked about types of projects and commodities dealt in as well as market distribution and forms of payment. The accomnanying charts show how the 17 responding E&C firms answered these and other questions. Other ME survey questions, and a review of company literature, yielded information about financing techniques and special challenges for E&C firms. Insights were gained concerning government impacts, customer-generated problems, and promising areas for development-including synfuels-in the minerals industry. These areas are discussed later in this article. Accompanying articles in the special issue discuss the E&C company's role in mining projects, research and development in E&C firms, one approach to contract work used by an E&C firm, and an E&C project case study.

Jan 10, 1980

By M. L. Nave, R. E. Melley

DC motor drives are available technology for belt conveyors. The success of the application in mining depends on adequate and timely consideration of DC drive features. The purpose of this paper is to familiarize and inform possible mining users of DC drive attributes.

Jan 1, 1996

By A. Ayoubian, V. Nasri

This Tunnel Connection project will include construction of two short tunnels to connect the existing subway tunnels (Red and Blue lines) in the northern loop area of downtown Chicago through a new station. The Southeast Tunnel will connect the Red Line to the new station below the intersection of State and Washington Streets and the Northwest Tunnel will connect the Blue Line to the new station below the intersection of Dearborn and Randolph Streets. The connection tunnels are located in a very dense urban area of downtown Chicago and under several important historical buildings. Both tunnels are curved at the intersections and located at a depth of about 7.5 m below ground surface in saturated soft clay with an average undrained shear strength of approximately 25 kPa. The design calls for minimizing surface disruption and ground displacement while maintaining normal operation of the existing subways during the construction of the connections tunnels. This paper presents mining and cut and cover tunneling alternatives for the project.

Jan 1, 2007

By J. Cheung, H. Rabia

The traditional methods for predicting mine air temperatures are based on steady state heat transfer models as developed by Voss (1969) and Starfield (1983). These models are useful in providing approximate predictions of air temperatures in trunk and gate roadways. More complex models are required to provide predictions along faces. In practice, the heat flow in underground mines is of transient nature and recent observations in some British Coal mines show temperature variations of up to 5°C during a working week at any one point. In addition, the recent introduction of district recirculation of mine air in British mines requires a more precise prediction of air temperatures during start up of the system or during breakdown. A transient heat transfer theory based on the work of Jordon is presented. The method lends itself easily to computers due to the large number of calculations involved. The proposed transient model is validated using actual temperature data collected in roadways in Wearmouth Colliery in the North East of England. The transient results are compared with the steady state predictions of Voss (1969). Finally, predictions of air temperature in roadways for a recirculation system will be made using both the transient and steady state models. Temperature predictions along faces will be made using a separate model.

Jan 1, 1989

By C. R. Stephan, N. B. Greninger, W. A. Slivensky

The U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) are participating jointly in a research program to evaluate strength characteristics and air-leakage resistance of various proposed seal designs for use in underground coal mines. Over 20 full-scale seals were constructed in the Bureau's experimental mine at the Lake Lynn Laboratory, air-leakage tested, then subjected to pressure pulses of 0.14 MPa or greater. A discussion on the experimental procedure, construction techniques, and the explosion and air-leakage test results is presented. Four types of construction material were used during this seal testing program: solid-concrete-blocks, low-density foam blocks, cementitious foam, and wood blocks. Only one of the solid-concrete block designs using a mortared thick wall survived the explosion and air-leakage tests. Most of the low-density foam block and cementitious foam seal designs were judged to meet the requirements to be considered a coal mine seal. One of the wood block convergence seal designs failed explosion testing. Based, in part, on these research findings, several alternative seal design constructions using low-density foam blocks, cementitious foam, or wood have been approved by MSHA for use in coal mines.

Jan 1, 1993

By Richmond Bennett

Airborne geochemistry became a reality with the advent of a high-sensitivity airborne gamma ray spectrometer with large volume NaI (TI) crystal detectors. Small variations in the concentration of potassium (as K40), thorium (as T1208) and uranium (as B1214) along the flight lines can be determined by measuring the gamma radiation with a sensitive airborne spectrometer. Small volume crystal spectrometers are useful only for detection of major surface uranium (Bi214) variations, but the large crystal volume system is an airborne geochemical exploration method capable of locating hydrothermal mineral deposits. Radioactivity as a guide to ore has been discussed in the literature by Damon (1950), Gross (1952) and others. The theoretical basis is that potassium, thorium, and uranium are concentrated in late stage solutions during magmatic crystallization. Thorium and uranium are concentrated in late stage liquids because their large atomic radius and high ionic charge prevent them from entering into the crystal lattice of common rock-forming minerals (Rankama and Sahama, 1950). Potassium, which has a large ionic radius and small charge, also can be concentrated in the high water content late stage fluids (Heier and Adams, 1964). A large proportion of uranium and thorium in rocks occurs around grain boundaries of the essential rock-forming minerals (Hurley, 1950). Uranium and thorium substitute for zirconium in zircon, a comparatively early forming mineral. However, most of the thorium and uranium is concentrated in residuals where they can be fractionated and incorporated into allanite, monazite, xenotime, and other minerals.

Jan 1, 1970