Search Documents

By Z. Henderson, J. R. Saylor, L. Rojas-Mendoza

"Diesel particulate matter (DPM) is a major occupational health hazard in underground mine environments, even with available abatement technologies. Prior work has demonstrated that micrometer-scale water droplets, or “fog,” may be effective in removing significant number fractions of DPM from a conditioned exhaust stream. Here, a series of laboratory experiments are described which demonstrate that such a treatment can remove significant DPM mass from an unconditioned stream. The removal mechanism involved coagulation of the DPM and drops. The fog treatment removed about 45 percent more DPM mass on average than no treatment. Varying engine load, flow rate and fog droplet number density did not significantly affect the results under the range of conditions tested. IntroductionDiesel engines have seen widespread use for well over a century due to their relatively high thermal efficiency and fuel economy (Heywood, 1988). Recently, however, the adverse health risks of diesel exhaust have become increasingly clear. The term diesel particulate matter (DPM) is used to refer to the solid components of diesel exhaust, which are an ultrafine mixture of elemental and organic carbon (EC and OC) and minor constituents including sulfates and metal ash (Kittelson, 1997). DPM is generally considered to occur almost entirely in the submicrometer range. It is classified as a carcinogen (Occupational Safety and Health Administration, 2013), and epidemiological studies have demonstrated a positive correlation between long-term exposure to DPM and other combustionrelated fine particulates and increased cardiovascular and pulmonary diseases (Pope et al., 2002; McDonald et al., 2011). Many of the risks of diesel exhaust are associated with the physical and chemical properties of exhaust components (Heywood, 1988; El-Shobokshy, 1994; Kittelson, 1997). Exposures are generally measured and regulated on the basis of mass concentration. However, DPM number density and particle size are increasingly recognized as critical factors in terms of health outcomes (Bugarski et al., 2012; Kittelson, 1997; Occupational Safety and Health Administration, 2013; Pope et al., 2002)."

Jan 11, 2017

By B. R. Arvidson

Rare-earth elements have some unique properties that are used in many common applications, such as TV screens and lighters. In the 1970's, rare-earths began to be used in a new generation of magnetic materials that have very unique characteristics. Not only were these stronger in the sense of attraction force between a magnet and mild steel (high induction, B), the coercivity (He) is extremely high. This property makes the magnetization of the magnet body composed of a rare-earth element alloy very stable, i.e., it cannot easily be demagnetized.

Jan 1, 1998

By Klaus Schönert

In the analysis of comminution processes, it is necessary to have a detailed knowledge of such sub-processes as: (i) The transportation of the particles to the zone where they are stressed, (ii) The stressing of the particles to a level high enough for breakage, (iii) The removal of the fragments that are smaller than the limit size from the grinding zone, and (iv) The prevention of agglomeration of the fine fragments. The breakage phenomena of particles is the most difficult sub-process to understand. It can be understood only by applying the principles of fracture physics to obtain information about the stress-strain field in particles which are loaded either by compression or by impact, and by using this theoretical knowledge to interpret experimental results obtained from single particle crushing studies. It is not only of academic interest to know how a particle breaks, but also it is important for practical applications because it provides a basis for evaluating both the direction and limitation for any potential comminution improvement.

Jan 1, 1971

By Liangguo Kang

Coal, as one of the vital sources of energy in China, has raised widespread concerns regarding its safety issues amidst the country’s economic growth driven by coal. To address this concern, this study employed the Kuznets curve, multiple linear regression, and data envelopment analysis models to investigate the impact of Chinese coal economic development on coal mine deaths from 1992 to 2021. The findings revealed a clear correlation between the Chinese coal economy and coal mine deaths. Specifically, per capita coal output, the death rate per million coal tons, and the death rate per hundred thousand persons exhibited positive, negative, and negative correlations, respectively, with the growth of coal income over the past three decades. Moreover, when the coal workers and coal output factors remained unchanged, the income of coal demonstrated a negative correlation with future changes in coal mine deaths. Notably, with three decades of coal economy development, substantial improvements in coal mine safety have been observed in China. Consequently, this research provides valuable insights for formulating safety measures and policies in coal mines across different economic levels, as well as a useful framework for assessing safety development in the coal industry.

Jan 20, 2024

By Nawal Kishore, Nilesh Pratap Singh, Amit Kumar Verma, Vikram Seervi

In India, demand for coal exceeds its countrywide supply, despite its natural abundance, due to failure to achieve high production targets, especially in opencast mines, which are responsible for 94.98% of total raw coal production within the country. Employment of technological solutions, such as surface miners, is key to achieving higher coal production and productivity in an eco-friendly manner, especially in the populated areas adjacent to the mining zone and, hence, require restricted blasting operations. It eliminates blast hole drilling, blasting, and primary crushing units, thus reducing related environmental hazards like ground vibration and fly rocks. This paper encompasses the applicability, advantages, constructional features, and performance assessment models for each working mode of a surface miner. The current paper discusses the correlation between coal production and key productivity indicators, namely, machine shift-time, pick, and diesel consumption of surface miner in three different geo-mining conditions. Furthermore, relationships between machine shift-time, pick, and diesel consumption of surface miner and coal production were evaluated through bivariate regression analyses along with their coefficient of determination. These key productivity indicators of surface miner follow polynomial relationships with coal production on a daily and monthly basis, having Pearson correlation values from 0.774 to 0.907 and coefficient of determination, from 0.664 to 0.909 in opencast coal mines.

Jan 20, 2023

By Edwin B. Wilson

The purpose of the panel's examination of coal mining research and development is to explore how the various groups that make up this research community might work together more efficiently and be more productive. The community, as defined here, includes federal and state governments, coal producers, manufacturers, unions, universities, and industry sponsored research organizations. The framework chosen for these discussions consists of brief presentations by the panel members on their views of the proper role and function of the group they represent. The panel members were also asked to highlight the economic, technical and institutional constraints that affect the performance of research and development and the use of the results. Following these presentations, a number of prepared questions will be discussed by the panel, and audience participation is invited. These questions were given several weeks ago to the panel members for their study. Before proceeding with the panel member reports, a brief review of the importance of R&D to the coal mining industry would be helpful to setting the stage for a constructive dialogue. It is appropriate to begin this review by mentioning that there is complete agreement among the research community that the major goals are: Improve health and safety Protect the environment Increase capital and labor productivity Increase resource recovery Since the basic functions of the academic, industrial and government sectors are different, we should expect that the research and development objectives and priorities, roles and responsibilities under each major goal will be different for each research group. The differences do not represent problem areas. However, problems will arise if the objectives are not properly interfaced at the appropriate time. The consequences of railing to understand the need for integrated programs will be the classic result, best described by the phrase --"a technical success but a commercial failure."

Jan 1, 1978

By A. L. Martikainen

Booster fans increase air pressure to overcome resistance, the objective being to force adequate amounts of air through distant workings. They are used in areas that are difficult or uneconomic to ventilate with main fans alone. Booster fans are currently permitted in underground coal mines in some countries; the United Kingdom, South Africa, Australia and Canada have been defined as major users. Booster fans are not allowed in the US bituminous and lignite coal mining operations at the present time due to safety concerns. This paper presents the history of booster fan use in coal mines of the United States during the last 90 years. Changes in regulations, as well as advantages and disadvantages of booster fan use, are discussed. Research and petitions for booster fan use are highlighted in order to bring the debate into focus.

Jan 1, 2010

By E. R. Bauer

In response to the mandates in the MINER Act of 2006, the National Institute for Occupational Safety and Health (NIOSH) conducted refuge alternatives research that included characterizing the utility, practicality and survivability of refuge chambers and outby safe havens. NIOSH also prepared and delivered a report to Congress in late December 2007 that summarized the findings of the re-search, included recommendations concerning the design and performance specifications for refuge alternatives, and focused on specific information that could inform the regulatory process on refuge alternatives. This paper highlights NIOSH?s research and recommendations concerning refuge alternatives, survivability evaluations of refuge chambers and presents a brief review of the current deployment of refuge chambers in underground coal mines in the U.S. The research has lead to the conclusion that refuge alternatives have the potential for saving the lives of mine workers if they are part of a comprehensive escape and rescue plan and if appropriate training is provided.

Jan 1, 2009

By Peter F. Mataich

The phosphate mining industry is a highly competitive one, one in which survival depends on the plant's ability to produce at costs equal to, or below, the competition. The solution toward getting costs down is usually one of scaling up the plants to get the most tons through at the lowest possible cost. Control of these plants has been an art. Few of them are well instrumented because until a few years ago reliable instrumentation was non-existent. International Minerals and Chemical Corporation was a pioneer in applying computer techniques to ore reserves analysis and mine planning and the success in these areas led to the question of whether we could not extend the advantages of computer processing into the plant itself. There was a great deal of doubt on the operator's end that this could be done successfully because of the lack of instrumentation and the fact that plant control was largely an art that was learned only after many years of experience. However, in 1965 the instrumentation picture began to look up and the new generation of process computers just coming on the market were considerably lower in cost than the previous ones. A preliminary study of the installation costs and the probable benefits that could be realized from computer control convinced us that a process control computer should be seriously considered for a new phosphate mining plant which was being designed.

Jan 1, 1969

The Environmental Session will consist of five papers dealing with various aspects of trace elements associated with coal. Analytical procedures to determine the amounts of trace elements will be discussed. Other papers will deal with trace elements in streams downstream from coal mines, potential pollution from wastes from coal preparation plants, potential recovery of trace elements, and potential pollution from trace elements as a result of the combustion of coal.

Jan 1, 1979

By José Maria Silva, Eugênio Oliveira, Ruberlan Silva, Thiago Souza, Lucas Reis, Lorena Guimarães, Matheus Bianchetti

Copper mine operations consistently generate a large quantity of tailings after their concentration processing. These tailings are either piled up or stored in a dam, where both alternatives of disposal lead to environmental impacts. The dam copper tailings have a huge potential for by-product production thus improving sustainability and profitability in industrial operations. This paper describes a study aiming at producing a magnetite pellet feed as a by-product from a dam chalcopyrite flotation tailings and generating free magnetite non-magnetic rougher tailings. The chemical assay and mineralogy analysis of dam copper flotation tailings indicate low Fe grade (6.34 wt%), high SiO2 grade (63.14 wt%), low magnetite (3.6 wt%), and high iron silicates content (22.72 wt%). The complex mineralogy of these tailings leads to the need of grinding the rougher magnetite pellet feed as fine as 80% of particles smaller than 20 μm ( P80) aiming at improving magnetite liberation. The proposed process route comprises a scalping screen, low field rougher, and cleaner magnetic separations using a drum magnetic separator (80 kA/m or 1000 Gauss), followed by silicates reverse cationic flotation as a recleaner step. With this process route, it was possible to produce a high-quality magnetite pellet feed reaching 68.00 wt% of Fe, 2.13 wt% of SiO2, 0.51 wt% of Al2O3, and 95.1 wt% of magnetite. The Blaine specific surface area was 2300 cm2/ g, being in the range recommended for pelletizing (1900 up to 3000 cm2/ g). The total mass, Fe, SiO2, Al2O3, and magnetite recoveries were 2.77%, 29.71%, 0.09%, 0.12%, and 73.17%, respectively. Most of the magnetite losses, around 20% of total magnetite fed, occurred in the oversize of the scalping screen. Additionally, it generated non-magnetic rougher tailings with less than 1.0 wt% of magnetite that could be used as by-products and reduced the amount of tailings disposal in a dam. This study contributes toward the sustainability of operation, minimizing tailings disposal.

Sep 28, 2022

By Amar Prakash, V. M. S. R. Murthy, VIVEK KUMAR HIMANSHU, Sufal Mehrotra, Ashish Kumar Vishwakarma

Raises are vertical or inclined openings made to connect two levels of an underground metalliferous mine. They are developed using drilling and blasting-based technique or by mechanical means. Raise boring machines (RBM) have evolved in recent years, which provide quicker and safer raise excavation. The penetration rate using RBM has influenced applied thrust. The required thrust to enhance penetration rate with optimal use of energy would be different under varying geological and geotechnical conditions. In this study, the influence of applied thrust on penetration rate using RBM has been investigated. The investigation has been made for two different rock types, amphibolite (AMP) and garnet-biotite-sillimanite-gneiss (GBSG). The numerical simulation model was developed for this purpose using Ansys-Explicit Dynamics. The induced tensile stress under different conditions of applied thrust has been analysed in the calibrated numerical model. The model output shows the power trend between the parameters. The experimental data on penetration rate was also collected along with the respective operational parameters. A statistical analysis has been carried out for the gathered data. The analysis of data also shows a power trend between thrust per cutter and penetration rate in both rock types and hence validates the numerical simulation-based output. Based on the outputs of the numerical simulation and empirical study of the experimental data, the optimum thrust per cutter for excavation in both rock types is in the range of 12–14 tons. The approach used in this study can be helpful for predicting the optimal operational parameters of raise boring machines under different geological/geotechnical conditions.

May 29, 2023

By Lawrence Lien

The reduced need for traditionally trained and educated personnel in the mining industry is systemic to the changing mining industry. Universities and other training institutions are meeting the traditional skill needs required by the industry, but are the skill needs going to be the same in the near future? The answer may be no. Mining is changing because of increased liabilities and costs of environmental and safety is-sues; lower grades of minerals in traditional mining activities and the advent of new bio-chemical processes and robotic equipment. More productive and economic alternatives, and larger, more sophisticated and automatic equipment, are also changing the industry. Engineering is more specific, accurate, precise and expensive. Measurement is more thorough and timely of progress, production, costs and productivity. And, the industry will likely be engaging in more undersea mining, possibly space-based processing, less human interaction and more remote control of events than was previously thought possible.

Jan 1, 2011

By Mahmud Esad Uluer, Seyed Hassan Amini, Aaron Noble, Matt Shigo

Airborne coal mine dust is an unintended and unavoidable result of coal extraction operations that raises notable health and safety concerns. Modern mining techniques utilize several dust mitigation strategies, and the flooded-bed dust scrubber (FBS) is one such technology used extensively on continuous miners. The conventional static panel filter, instrumental in most scrubber designs, is fundamentally limited in collection efficiencies due to a high clogging rate and a tradeoff between mesh density and airflow rate. To overcome these deficiencies, a novel vibrating mesh panel is proposed. In this study, a laboratory-scale dust scrubber unit was used to investigate the efficacy of concept as compared to that of a static mesh. A statistical design of experiments study was first used to determine the effective vibrational parameters and scrubber operational parameters on dust collection and clogging mitigation. Optimized results from this study were then evaluated against those of a static mesh to determine performance improvement while investigating the mechanisms controlling dust collection and particle department through the scrubber system. Results show that the vibrating mesh conditions and higher water flow rates led to an improvement in the collection efficiency of the scrubber system. Compares to a static-mesh, the vibrating mesh FBS showed a significant reduction in pressure drop across the mesh screen indicating lower air loss through the test duration. Overall, the findings confirm that vibrating filter mesh reduces filter clogging while maintaining high collection efficiencies. This research supports further technological advancement in mine dust mitigation technologies.

Dec 27, 2023

By P. Zhang

The Crago “Double Float” process is widely used in upgrading phosphate ore. This process is inefficient, as it floats about 30-40% of the sands in the flotation feed twice and requires a deoiling step. This paper summarizes several research projects on improving phosphate flotation. The University of Utah investigated a new flotation chemistry for efficient flotation of phosphate in a single step. The Florida Institute of Phosphate Research developed several single-collector, all-anionic flotation flowsheets using various sizing schemes. In addition, Eriez invented the HydroFloat separator, which demonstrated great potential for processing coarse flotation feed in one step.

Jan 1, 2004

By Adabala Raja Venkata Sai Naresh, Radhakanta Koner

Particle size distribution (PSD) is an essential parameter in assessing the overall efficiency of blasting operations in mines and the subsequent mine-to-mill process in the mining industry. Despite some drawbacks of 2D image analysis techniques in accurately estimating particle sizes in PSD, the mining industry has relied on them for the last three decades. This study proposes the 3D rock fragmentation measurement (3DFM) technique for deducting the accurate dimensions of 3D rock particles for the PSD. 3DFM has utilized different processing algorithms. Images of different views of the non-touching rock particles of varying sizes have been acquired as a data acquisition step of structure from motion technology for generating sparse point cloud. Dense point cloud reconstruction is used to avail finer details of the point cloud using clustering views for the multi-view stereo algorithm. Random sample consensus (RANSAC) algorithm coupled with an unsupervised classification using the density-based spatial clustering of applications with noise (DBSCAN) classifier is employed to extract the rock clusters from the 3D point cloud. Finally, the accurate rock sizes are derived using the hybrid bounding box rotation identification (HYBBRID) algorithm with a root mean square error (RMSE) of 0.10 cm for length, 0.10 cm for breadth, and 0.32 cm for depth. The PSD of rock fragments obtained from the proposed 3DFM technique is found to be matching with the results of mechanical sieving and manual gauging with an R2 values of 0.98 and 0.99, respectively. The 3DFM method can be considered cheaper, more accurate, and computationally faster in determining the rock dimensions for the PSD determination method to enhance the productivity of the mining industry.

Dec 29, 2023

By Shaoxian Song, Ling Xia, Hongqiang Li, Yubiao Li, Yunliang Zhao, Shaobing Xie

Since human daily demands for fresh water have been increased significantly, the supply of fresh water for the mining industry, especially froth flotation, should be considerably reduced. In addition, stricter environmental standards have been implemented in many countries to reduce the risks due to the disposal of wastewater, many flotation operators have to seek more efficient ways to utilize the limited fresh water sources. Recycling water with high concentrations of impurities is a normal strategy for most of the mineral processing plants; however, water quality should be carefully considered to guarantee a smooth flotation process. Recently, the application of seawater in flotation has attracted much attention due to its availability and abundance rather than fresh water. However, the influencing mechanisms due to the application of seawater in flotation have not been fully understood especially the reactions between mineral particles and bubbles in the presence of high concentrations of cations and anions. This would impede the application of alternatives to fresh water in the flotation. Therefore, this paper reviews the current water sources and the technologies for water recycling in the flotation process. Specifically, the life cycle of water in flotation was proposed. In addition, the strategies including high pulp density flotation as well as the most promising alternatives to fresh water have been discussed in details, with the related mechanisms being demonstrated.

By Lauro Lacerda

Shotcrete is a highly adaptable and widely used underground construction material at infrastructure and mining projects around the world. In fact, many projects could not have been completed without its utilization. As underground projects became larger the use of mechanized wet-mix spraying gradually replaced manual dry-mix shotcrete applications. This paper details some of the reasons for that and provides information on the equipment and operational factors including safety and productivity required to successfully complete underground shotcrete projects.

Jun 13, 2021

By James P. Connell

The American Concrete Institute defines "shotcrete" as "mortar or concrete conveyed through a hose and pneumatically projected at high velocity unto a surface." This definition thus includes what is traditionally known as "gunite," which is a pneumatically applied mortar. In mining practice, the term shotcrete is restricted to pneumatically applied concrete, and this differentiation will be used in this paper. In 1914, following the invention of the mortar gun in 1907, the then Chief Engineer of the U.S. Bureau of Mines, George Rice, developed the guntie process for underground test work at the bureau facility at Bruceton, Pennsylvania. After World War I, gunite was used extensively in American mines and was also utilized for underground civil works such as the San Jacinto Tunnel in California. The greatest development was In Europe where, as early as 1911, gunite was successfully used as an overlay for deteriorated tunnel linings. In 1951, the Swiss firm Aliva developed a pneumatic gun capable of handling coarse aggregate, thus making possible the first use of shotcrete at the Maggia hydropower development. Intially, shotcrete was used to reduce manpower requirements for forming; and placing conventional concrete. However, by 1954 Sonderegger was reporting that the structural advantages of shotcrete were derived from its flexibility and from the fact that it could be applied almost immediately niter the opening had been made. The incorporation of wire mesh into the shotcrete led to the New Austrian Tunnel Method, or NATM. The use of shotcrete in American mines has been implemented more recently. This delay seems to be due to previously unsuccessful experiences with gunite as a structural material and to the U.S. reliance on wood or steel supports in main line haulageways. The long experience with the apparently more substantial rigid supports led mine operators to be reluctant to the new and seemingly unrealistic lighter shotcrete support.

Jan 1, 1977

By Arthur B. Johnson

Potassium, is one of the three basic plant nutrients along with nitrogen and phosphorus. There is no substitute for potassium compounds in agriculture; they are essential to maintain and expand food production. Potash is found throughout the world in both soluble and insoluble forms. It is only the soluble forms that are economically attractive to process, primarily chlorides and sulfates, with potassium chloride by far the most important potash salt. Sylvinite ore, a mechanical mixture of sylvite (KCl) and halite (NaCl), is a natural mineral of potassium. This ore is found in commercial quantities in the Permian sin region near Carlsbad, New Mexico. Vast tonnages of high-grade de, low-clay-content ores have been mined and concentrated during the past 40 years; however, these deposits are rapidly being depleted leaving high-clay, low-grade ore reserves of over 135 million tons. These ores, containing 13 to 22 percent K20 and 3 to 8 percent clay slimes; cannot be effectively processed by current commercial flotation methods. The present concentration processes for potash minerals in Carlsbad relate mainly to ores containing 1 percent or less of clay-slimes with a K20 content of 20 to 25 percent to yield products to meet the requirements of the agriculture market, namely, 95 percent KC1 equivalent to 60 percent K20. Discoveries of potash ore in Saskatchewan, Canada, have shifted the emphasis on expansion outside the United States. Presently, the American companies are looking to Canada for future growth, expenditures, and expansion. Four of the seven companies operating near Carlsbad are produces of Canadian potash despite the large investment sons required for shaft sinking and milling installations.

Jan 1, 1970