Search Documents

By C. D. Litton

Laboratory experiments were conducted to determine the responses of a prototype smoke detector and a commercially available photoelectric smoke detector to smoke particles generated from various combustion sources. The prototype smoke detector combines optical scattering measurements with ionization chamber measurements in order to reduce/eliminate nuisance alarms due to the presence of airborne dusts or diesel exhaust particles. The commercially available smoke detector is designed for use in harsh environments where airborne dust represents a major problem due both to nuisance alarms and detector contamination. In the experiments, the responses of the two detectors were measured when exposed to smoke particles from the exhaust of a diesel engine and from a variety of fire sources, including wood, coal, styrene butadiene rubber, and No. 2 diesel fuel. For the solid fuels, data were obtained for both smoldering and flaming combustion. This report describes the experiments, their results, and the use of these results as they apply to early-warning fire sensors capable of the rapid and reliable detection of fires in atmospheres that may or may not be contaminated by either airborne dust or the products produced from diesel engines. Subsequent to these laboratory experiments, six smoke detectors were installed in an underground limestone mine for further testing and evaluation. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By C. H. Rawlins

Deep bed media filtration is used as a tertiary treatment step (after hydrocyclones and flotation cells) to remove fine oil droplets and solids from oilfield water before reinjection disposal or to remove particulate material from surface waters used for waterflood injection. Oil and solids injection requirements are typically <5 ppm concentration at <2 micron diameter. The preferred media for produced water filtration is walnut or pecan shell, however the use of this media has evolved by trial & error and the fundamental mechanisms that occur during separation and media cleaning have not been investigated. A project was initiated to fill in this knowledge gap by analyzing the physical, mechanical, chemical, and hydrodynamic properties of six types of granular filtration media (12/20 mesh size): garnet, silica, anthracite, pecan shell, English walnut shell, and black walnut shell. Comparison of bed packing, oil wetting, attrition resistance, particle strength, and fluidization has led to an understanding of the preferred filtration media for separation of fine oil droplets and solids.

Jan 1, 2010

By Norbert Patzelt, Johann Knecht, Wolfgang Baum

High pressure roll grinding (HPGR) is a mature but still expanding comminution technology. In the metals mining industry, HPGR is slowly gaining acceptance as a cost-efficient, high-throughput alternative for plant optimization. The increasing need to treat ores with progressively lower grades, complex mineralogies, refractory metal occurrence and variable rock types requires an energy-efficient comminution technology that reduces metallurgical problems inherent in conventional crushing and grinding, while stabilizing leach and flotation circuits and increasing metals extraction. This paper will summarize our latest HPGR pilot test results for gold and copper projects in the United States and South America and their confirmation through the first HPGR operation in copper mining. This paper will also stress the use of the high pressure grinding roll as a metallurgical tool. The application of HPGR for the treatment of heap leach SX-EW ores, semi-refractory gold ores, waste rock material and concentrator feeds will be illustrated.

Jan 1, 1998

By Zhang Youdi

According to general guidelines, deposits suitable for surface mining can be divided into two basic categories: horizontal or flat-bedded deposits and inclined or dip-buried deposits. A series of mathematical models for surface mine long-term planning (SMLTP) has been developed and can be used for any kind of deposit. The basic theory and methodology of the models are oriented- graph simulation which combines graph and network theory with a systems simulation technique to form a new approach. From the viewpoint of surface mining and long-term plan modeling, the main differences between the two categories of deposits are analyzed, an important algorithm is put forward, and the structure of the models and some results of applications are introduced. Dynamic and comprehensive optimizations have been completed by the SMLTP model series. Combining different OR branches, the new approach has been proved to be a powerful tool to solve the strategic problems of surface mine planning.

Jan 1, 1989

By Pierre Mousset-Jones, Felipe Calizaya

The design of an auxiliary ventilation system for long underground openings (drifts, ramps and shafts), often requires the installation of multiple fans. The fans are installed in series and separated from each other by rigid ducts of fixed or variable length. However, problems relating to excessive leakage often occur, with each project representing a unique problem requiring an efficient solution. In this study, a method to determine the design parameters of an auxiliary ventilation system is presented. The method is based on the principle of partitioning a long ductwork into segments of finite length and solving the resulting networks separately. Specifically, the method is developed to solve two types of problems: constant fan spacing, and constant fan size. In the former, the fan spacing is fixed, and the problem is solved for fan sizes. In the latter, the problem is to solve for fan spacing. An example is used to illustrate the method.

Jan 1, 1993

By Ehsan Alavi, Eren Kusdogan

The City of Toronto’s Coxwell Bypass Tunnel is currently being constructed by North Tunnel Constructors ULC, a joint venture of Jay Dee Canada, C&M McNally Tunnel Constructors and Michels Canada. This project includes construction of approximately 10.5 km of 6.3 meter finished diameter rock tunnel, five 20 meter diameter storage shafts and eleven tunnel connection drop shafts, along with associated deaeration and adit tunnels. This paper describes progress on the project to date and reviews the risk mitigation measures utilized on the project to move the project forward through tough geological conditions during shaft excavation and tunneling phase of the project.

Jun 13, 2023

By Robert Stefanko

The results of a recent study on the influence of continuous and conventional mining techniques on the size consist and wash- ability characteristics of coal are presented. Eight samples, four each from continuous and conventional mining sections were collected. Each sample was screened in seven size fractions, and each size fraction was totally fractionated at five gravities. The data thus collected was statistically examined for the influence significance of mining techniques, size, and gravity on the quality of the mined product. The paper presents the sample collection method, data gathering and analysis procedures, and major conclusions. The study revealed that there are pronounced differences in the products from the two mining systems and that conventional mining yielded a better product in terms of size-consist, and yield, ash, and sulfur in both the raw and washed products. The results of the study are significant in regard to consideration of resource utilization and conservation, and environmental impacts.

Jan 1, 1974

By Finn Ouchterlony

INTRODUCTION Much of present fracture toughness testing con¬cerns chevron notched specimens (Newman Jr., 1984) since these, in principle, require neither fatigue precracking nor more registration than failure load to determine fracture toughness. Two such specimens which can be made from diamond drilled rock cores with minimal machining are the Short Rod (Barker, 1977) and the Chevron Edge Notch Round Bar in Bend¬ing or CENRBB Specimen (Ouchterlony, 1980). Even if the precracking property is especially valuable for a material like rock, practice has made the relative advantages of these chevron notched specimens much less apparent (Ouchterlony, 1982; Ouchterlony and Sun, 1983). Enough remains, however, to have the Commission on Testing Methods of the International Society for Rock Mechanics (ISRM) focus on them as standard configurations in a "Suggested Method for Determining Fracture Tough¬ness of Rock Material", which is in preparation. This paper presents material which supports the ISRM effort: 1. An experimental compliance calibration of the Chevron Bend (CENRBB or CB for short) and re¬sulting formulas. 2. Specimen tolerances, evaluation formulas, and loading rate requirements relating to both Short Rod and Chevron Bend Specimens of suggest¬ed standard proportions. 3. Some fracture toughness values obtained with the Chevron Bend Specimen. This material is mainly based on two reports (Ouchterlony, 1984 and 1985). CALIBRATION OF THE CHEVRON BEND SPECIMEN Preliminaries The specimen and basic notation is shown in Figure 1 together with a straight notched variety (SECRBB). Subscripts c and s are sometimes used below to distinguish between them. Assuming linearly elastic conditions the load point compliance [ ]

Jan 1, 1986

By B. K. Parekh

Sludge obtained during production of magnesium (Mg) metal from electrolyzing of molten MgCl2 contains entrapped magnesium particles. The sludge material containing the magnesium particles is a friable, continuous matrix of frozen salt mixture which may also contain some oxides and impurities. A dry process was developed for recovery of magnesium metal from the sludge, utilizing minerals beneficiation unit operations. The steps included selective comminution, screening, attritioning and tabling. Recovery of the high grade (+90 percent) metal was in the 70 percent range. The process is being commercially used in the U.S. The novel process was also successfully applied to a magnesium-alloy for recovery of metal from the sludges.

Jan 1, 1995

By R. Hogg, S. Chander

An overview of various physical and interfacial characterization methods for use in mineral processing is presented in this paper. The availability of a large number of characterization techniques and commercial instruments requires that the reliability and limitation of each be carefully examined. The choice of a method may depend upon the manner in which the information is to be used, for example, in development of new processes, plant and process design, plant control, problem solving, etc.

Jan 1, 1987

By T. Hudaverdi

Several studies have been conducted on blastability and prediction of fragmentation. The term blastability is used to refer the susceptibility of the rock to blasting and is closely related to fragmentation. Parameters that determine fragmentation by blasting may be divided into two groups. The first group consists of blasting design parameters. The blast design parameters are controllable parameters and determined by the explosive engineers. The burden, spacing between holes, bench height, drillhole diameter, stemming height and explosive density are all design parameters. The second group consists of rock mass parameters that are referred to as uncontrollable parameters. The uncontrollable parameters are physical and mechanical properties of rock and rock mass structure. The strength, modulus of elasticity, density of rock, number of joint sets, joint orientation and joint spacing are among uncontrollable parameters. The rock mass parameters and blast design parameters should be considered together to explain fragmentation process. In this study, a blast database was accumulated to use for multivariate analysis. The blast database contains the blasts performed near Istanbul region quarries and the blasts that were preformed in various mines in the world by the blasting researchers. The cluster analysis was used to separate the blast data into different similarity groups. Group memberships were analyzed and checked by the discriminant analysis. Then, the multivariate regression analysis was used to develop a prediction equation for blast fragmentation for each group. Finally, a validation of the suggested models was performed for various mines. The model comprises blast design parameters, mechanical properties of rock and rock mass structure.

Jan 1, 2011

By Rudecindo S. Silo

[The principal characteristics of the process is that when applied in medium or in great degree it only needs unelaborated raw materials such as sodium chloride and calcium carbonate, or of medium elaboration, as sulphur which is found in large quantity in the North of Chili; however, the may be also applied to small copper plants provided that low cost sulphuric acid is available as a substitute for sulphur, that is, in. those plats of small capacity where large additional installations are not needed for the regeneration of the leaching solution. The method itself comprises 6 stages, namely: crushing, leaching, washing; of solutions, precipitation, regeneration of the leaching solution and fusion.]

Jan 1, 1965

By Edward J. Zeigler, John T. Miller

INTRODUCTION Construction of Phase I, Section A, of the Baltimore Region Rapid Transit System required that six underground stations be built using a cut and cover excavation technique. For five of these stations, soldier piles, used as support of excavation, were installed with tip elevations well below the bottom of the excavation. However, in the case of the sixth subway station, the Mondawmin Station, soldier piles were installed only through soil and decomposed rock, with the tips of the piles being stopped well above the bottom of the excavation in partially decomposed rock. Below the tips of the soldier piles, and below a cut slope where piles were not installed, the sides of the excavation consisted of partially weathered and fresh rock and were supported by a combination of rock bolts, wire mesh and shotcrete. An extensive installation of geotechnical instrumentation permitted detailed monitoring of horizontal and vertical movements of the soldier piles and the walls of the excavation. Preliminary studies indicated that the excavation support system selected for the Mondawmin Station would have several advantages over a conventional system consisting of soldier piles extending to the bottom of the excavation, braced with prestressed struts. These advantages included lower cost of installation, a decreased time required for installation, and a more open excavation for the contractor during construction of the station. The Mondawmin Station is situated in the northwestern quadrant of Baltimore City, approximately 6.4 km (4 miles) from the center of the City. The station lies midway in a project 12.9 km (8 miles) long identified as Phase I, Section A, of the Baltimore Region Rapid Transit

Jan 1, 1981

By S. K. Kawatra, S. Valluri

With increased CO2 emissions from steel and coal industry, there is great opportunity to capture CO2 and utilize the captured CO2 for economic advantage. The primary goal is to develop energy-efficient processes that reductively couple CO2, an abundant and renewable carbon source, for the production of value-added chemicals such as methanol, ethanol, and oxalic acid. These chemicals can be used elsewhere in the refining process or sold as valuable by-products. Geological sequestration, in comparison, has no economic return. Current CO2 utilization research at Michigan Technological University focuses on electrochemical reduction of CO2. Electrochemical reduction of CO2 to hydrocarbons and other chemicals is a complex multistep reaction with adsorbed intermediates. The exact reaction mechanisms leading to various products are not clear from the literature to date and will likely change over the range of conditions like pH, electrode potential, electrolyte medium, catalyst, etc. This paper will present different ideas and their viability to utilize CO2 as a feedstock to produce several value-added compounds. INTRODUCTION Carbon dioxide (CO2) emissions into the atmosphere will need to be drastically reduced to curb the various undesirable effects of climate change. The large contribution in total CO2 emission originates from coal or natural gas power plants, and a considerable amount from steel plants. Average CO2 emissions in the US from steel industry is 2.9t CO2/t steel (Global CCS Institute 2013). Capturing the available CO2 from the steel and coal industries for economic advantage is a win-win situation for the industry. This technology is not only important scientifically but is also vital for a sustainable future. The various ongoing investigations can be categorized as biochemical, thermochemical, photochemical, and electrochemical approaches. Among these, the electrochemical method shows the most promise as an efficient form of CO2 conversion technology, because of its many advantages like high reactivity under ambient conditions and good extensibility from small- to large-scale processes1 BACKGROUND Extensive research has been done on the chemistry of transforming carbon dioxide into more useful products. Methods are known to convert carbon dioxide into a wide variety of substances, including methanol, isobutanol, carbohydrates, methane, carbonates, urea, formic acid, oxalic acid, carbon monoxide, epoxides, formaldehyde, and so on. Several of these (carbohydrates, formaldehyde, isobutanol etc.) are primarily results from biological processes. The rest are results of strong reduction reactions or electrolytic reduction. In short, electrolytic reduction can be used to form methane, methanol, formic acid, oxalic acid, carbon monoxide from carbon dioxide2. CO2 reduces at the cathode in an electrolysis cell. These processes have the general form of generating the carbon dioxide anion radical (2⋅−) and allowing it to react with itself or the electrolyte3. Catalysts can be added to influence the formation of the anion radical or to suppress side reactions3. The electrolyte, catalyst, voltage, electrode material and CO2 content are all known to effect the reaction pathway. Table 1 shows the overall reactions and energy requirements for electrochemical conversion of CO2 to chemicals

Jan 1, 2019

By T. Lilley

The use of membranes in wastewater systems has increased rapidly in recent years. Microporous or semi-permeable barriers augment conventional chemical or biological processes to meet stringent treatment targets. These developments enable elegant solutions to wastewater discharge challenges and extend the scope of water recycle redressing the overall water balance and operational economics Wastewater treatment processes are discussed by reference to the spectrum of waterborne contaminants and the respective membrane separation capabilities. The role chemical pre-treatment to enable physical separation of metals with micro-filtration (MF) is described and how integration of MF with reverse osmosis (RO) is used to control a broader range of dissolved contaminants Membrane configurations are considered apropos function, operational economics and sustainability. These features are exemplified with case studies. Firstly, MF alone following chemical precipitation for the removal of heavy metals, then MF onto two stages RO of different configurations for TDS reduction and waste volume minimisation and finally an open channel RO alone for the reduction of inorganic COD from a leach stream.

Feb 27, 2013

By John T. McDonough

The Climax Mine of AMAX&apos;s Climax Molybdenum Division is currently producing approximately 34,000 tons of molybdenum ore per day from two underground levels (see Figure I), and initial design is underway for the next deeper (1200) level. The aim of this report is to present the methods of site evaluation used at Climax for cavability determinations and underground support design. Climax succeeds with its panel caving system of mining (Julin, 1973) (Figure 2) largely because of the presence of pervasive geologic structural discontinuities. The stockwork ore body at Climax was formed by the multiple intrusion of mid-Tertiary rhyolitic magmas into Precambrian granite, schist and gneiss, and the hydrothermal emplacement of molybdenite into the network of fractures that were generated during the forceful upward intrusion of magma. Subsequently, intrusive events that were more deeply seated refractured the overlying, ore- bearing stock and propagated a complex system of axial and radial fractures. Post-ore movement along the Mosquito Fault (Wallace, 1968) and its associated stranded shear zones further fractured the ore body and disordered the existent geologic structure. The result of these structural events is a brittle, crystalline ore body that is transected by a complex pattern of faults, shear zones, and joints that augment cave initiation and enhance comminution of the ore blocks. Generalizations can be made about the structural trends within the ore deposit (King, 1946; Kendorski, 1973), however, the intensity and orientation of geologic structure is by no means uniform throughout the ore body. The relative intensities of silicic and argillic alteration are also highly variable (Vanderwilt and King, 1955). As a consequence, no single rock-mass model suffices as a standard for mine design, and site characterization for cavability and support design is a continuous process.

Jan 1, 1977

By Ted H. Eyde

Nearly 17 years ago a major producer of synthetic zeolites started an extensive exploration program for natural zeolite deposits which resulted in the discovery of over 170 occurrences in the western United States. A few years later several of the other producers and consumers of synthetic zeolites also started similar exploration programs. Since then, small quantities of natural zeolite minerals have been produced from at least 12 deposits in the United States. Of these the Bowie deposit, about 13 miles north of Bowie, Arizona, is the most important,having produced over 5,000 tons of vitric tuff zeolitically altered to the mineral chabazite and minor amounts of the minerals erionite and clinoptilolite. Mining Districts and Mineral Deposits of Arizona compiled by Charles A. Mardirosian, Consulting Geologist, estimates the value of the total production from the Bowie deposit at a very conservative $2,000,000. Unfortunately, none of the companies responsible for the discovery and the initial production of natural zeolites made any effort to develop the high volume, low cost applications of this unique mineral raw material. Instead, they developed only the high unit value uses to supplement their existing synthetic molecular sieve product lines. With the producers of synthetic zeolites thinking in pounds and not in tons, further development of natural zeolite deposits stagnated for over a decade.

Jan 1, 1974

By Marie-Antoinette Dziurla, Barrie Johnson, Åsa Kolmert

Acidophilic bacteria are well known for their role in accelerating the oxidative dissolution of sulfide minds, such as pyrite. Other acidophiles, however, are able to catalyze dissimilatory reductive reactions. Bacteria that reduce ferric iron to ferrous, and sulfate to sulfide, were isolated from ARD-impacted environments and immobilised onto porous beads made of recycled glass. Column bioreactors containing colonized beads were constructed and peacolated with synthetic and actual ARD, and evaluated for their capacities to promote iron or sulfate reduction, and pH amelioration. Iron reduction did not require strictly anoxic conditions in bioreactors, and rates of up to 800 mg Fe3+ reduced/(l*day) were achieved, with a conversion efficiency of up to 98%. Using mixed populations of acidophilic fungi and iron-reducing bacteria, the bioreactors were capable of promoting iron reduction using paper pulp as sole carbon and energy source. Reduction of sulfate in pack bed bioreactors was observed with acidic wastewaters of pH 3 and above, though average rates of 300 mg sulfate reduced/(l*/day) were less than those recorded for circum-neutral pH systems. Bioremediation of ferric iron-rich ARD was assessed using coupled iron-reducing and sulfate reducing bioreactors.

Jan 1, 2000

By K. S. Eric Forssberg, Lennart Ryk

The paper discusses coal utilisation in Sweden. All hard coals have to be imported from other countries. Peat from domestic sources is used as a complement. Environmental legislation and taxation on fuel and emissions are severe. This situation affects the procurement, preparation, handling and use of coal. The paper presents: • R&D projects concerning deep cleaning of thermal coal. • Handling and treatment of coal used in PFBC boilers and for blast furnace injection • Dust prevention for coal and peat briquettes. Procurement of coal emphasising quality and environmental issues.

Jan 1, 1995

By J. F. Able, F. Djahanguiri

The US Bureau of Mines conducted research on underground stope leaching of metalliferous ores. Leaching underground would minimize the environmental impact of ore processing on the surface and would maximize minable reserves. An important aspect of this process is the minimization of pregnant solution losses and groundwater contamination by leach solutions. Bulkhead design and construction are important issues for solution control and stope-leaching economics. A reinforced-concrete bulkhead was designed, constructed and tested for solution control in an underground mine near Idaho Springs, CO. This paper presents the bulkhead-design methodology and construction procedure.

Jan 1, 1998