Search Documents

By Hans Hamrin, Bruce Kennedy

Once an ore body has been probed and outlined, and sufficient information has been collected to warrant further analysis, the important process of selecting the most appropriate method or methods for mining can begin. At this stage, the selection is preliminary only, serving as the basis for a project layout and feasibility study. Later, it may be found necessary to revise the details, but the basic principles for the ore extraction should remain a part of the final layout. With respect to the basic principles employed, relatively few mining methods are used today. For the purposes of this presentation, the principles are classified as follows: 1) For naturally supported stopes, the available methods are room-and-pillar mining and sublevel stoping. 2) For artificially supported stopes, the available methods are shrinkage stoping, cut-and-fill mining, square-set mining, and longwall mining. 3) For caving methods, the available techniques are sublevel caving and block caving. Due to the uniqueness of each ore deposit, the variations on each of these methods are nearly limitless. It is impossible to include even the major variations in this chapter; the goal of this chapter is to present the principles as a guide to the mining engineer in adapting the general methods to specific needs. The selection process described herein is intended to supply the techniques by which the candidate methods available for a given ore body can be reduced to one or two feasible approaches. The feasible approaches then can be evaluated in detail, and the particular modifications can be investigated. In describing costs and economic factors, all values herein are expressed in terms of 1978 US dollars.

Jan 1, 1982

By D. Diggins

Experimental apparatus for the determination of powder wettability is described. The principle of the technique is based on the measurement of the equilibrium capillary pressure in a packed bed of particles. Both the macroscopic solid-solution-vapour contact angle, e, and the specific surface area, A(m2g-1), of the powder, can be obtained. Experiments on angular quartz particles have been performed. A wide range of situations have been covered: hydrophobic and hydrophobic particles wetted with water, a variety of organic liquids and solutions of surfactants. The results show that reliable and reproducible values for 0 and A for angular and relatively coarse powders can be obtained with the proposed equipment for advancing liquid fronts in the absence of soluble surfactants. In the latter case and for receding liquid fronts in general, only qualitative trends have been obtained.

Jan 1, 1992

By d&apos, L. F. G. Assumpcao

Kaolin samples from Rio Capim resources were treated in conventional and superconducting magnetic separators to study the main variables that influence the color removal process. Coating clays and delaminated clay were tested. Retention time (or pulp injection velocity), magnetic field intensity and matrix type were the' variables studied. The feed brightness ranged from 84.7 to 87.6 % ISO for the coating clays and from 80.7 to 85.4 % ISO for the delaminated clay. The results showed unleached brightness values higher than 88 % ISO for coating products and higher than 87 % ISO for the delaminated product, using a conventional magnetic separator with an applied field of 1.5 to 2.0 Tesla. With a maximum field intensity in the superconducting machine of 5.0 Tesla, unleached brightness values higher than 88.5 % ISO for both coating and delaminated clays were attained.

Jan 1, 1995

By Malcolm J. Lake, P. Brad Marchant, Linda M. Broughton

Thiourea is recognized as a technically competitive alternative to cyanide for gold and silver extraction for a variety of ores and concentrates. This paper describes the results of a recent mini-pilot locked cycle test comparing cyanidation with acidothioureation treatment of gold bearing sulphide concentrate. The gold extractability of both methods was similar. The comparative metallurgical operating conditions and test results are summarized. Detailed byproduct solution analyses and environmental toxicity test results are presented and suggest that thioureation might result in acutely toxic byproducts even after treatment. Comparative process economics are summarized based on preliminary commercial operating flowsheets derived for the locked cycle case study. Capital and operating cost estimates are shown. The results indicate that cyanidation is more economically favorable within the constraints of the case study. Considerations for process selection between thioureation and cyanidation, for conceptual case studies, are discussed.

Jan 1, 1998

By R. M. Schuster

This study attempts to compare the costs of transporting coarse coal by pipeline, versus the more conventional use of belt conveyors. Hydraulic conveying of crushed (not pulverized) coal has not had widespread commercial acceptance. However, there is little doubt that the technology is available, so that, should this method be proven economical for a given application, implementation of this technology will become more acceptable. Hydraulic transport by pipeline between the mine stockpile and the coal preparation plant, for distances normally considered practical for an overland belt conveyor, should be an ideal application. In this application there is no need for dewatering facilities at the receiving end of the pipeline, because, the receiving screens at the plant serve this purpose. Further, clarified water from the preparation plant can be recirculated back to the mine, a plus for water resource and environmental considerations.

Jan 1, 1982

By Rafael C. Castro, John Overton, Gregg Sherry, David A. Sutter

This paper presents an innovative ground support solution developed to construct a tunnel cross-passage for the MUNI Metro Turnback (MMT) Project. A “soft center” jet grouting approach was designed to provide solid ground support while maintaining a soft center to allow for hand-mining of a 2.44 m (8 ft.) wide, 3.66 m (12 ft.) tall and 4.6 m (15 ft.) long cross-passage through soft Bay Mud. Prohibitive costs and schedule impacts associated with mining under compressed air (at the time being used for main tunnel construction) were the catalysts to search for alternative methods for cross-passage construction. Limited surface disruption, relatively low costs, ease of subsequent excavation, nominal schedule impacts and proven local success of jet grouting were key factors in selecting and designing this method of ground support.

Jan 1, 1997

By V. Fred Swanson, J. Patrick Glynn

The environment for process engineers today is very different from 20 years ago. The ideas and mathematical description of models for a multitude of different unit operations is an ongoing development. The computer tools to deal with the mathematics are readily available and specialist companies have developed, tested and verified their models. The challenge for the process engineer is to know which package to use and to know whether a particular application is the most accurate for the specific process. Metallurgical simulation programs today are well known and proven. Certain programs are specialized while others are broader based. The needs of each user are dependent on the application. Typically, most users require the following operations: • Comminution • Flotation • Hydrometallurgy • Pyrometallurgy • Additional requirements could be defined as: • Thermodynamic capabilities for solids, phases, and gases • Dynamic simulation • Data analysis tools • Coal oriented operations • Diamond oriented operations

Jan 1, 1997

By Albert E. Ketler

The techniques for fire monitoring of conveyor belts in underground coal mines have been revolutionized by the advent of sensitive carbon monoxide sensors and computer monitoring systems. These new systems are rapidly replacing the previous thermal (fixed-point temperature) sensors that have been shown to be considerably less sensitive for early fire warning. CO is generally an excellent indicator of spontaneous combustion. However, the most recent non-flammable conveyor belt materials have been shown to "burn" with dense smoke, but without sufficiently high temperatures to produce much carbon monoxide. To cover this fire detection void, a smoke detector was developed to augment CO sensing for these new conveyor materials. However, computer monitoring provides the flexibility for handling this and other additional instrumentation as fire monitoring techniques evolve. CO, smoke and temperature sensing may eventually be advocated for complete fire monitoring.

Jan 1, 1987

By A. K. Ghose, S. Chakraborti

The research work outlined in this paper examines the utility of index tests for evaluating the strength of coal, both in the laboratory and in-situ. For routine evaluation of strength and deformation properties of coal seams, as inputs for design in stability analysis and equipment selection, the index tests are cost-effective and also make less demand on time and manpower. Four index tests, namely Protodyakonov Index, Cone Indenter Index, the Point Load Strength Index and Schmidt Rebound Hammer, were evaluated for 13 coal samples and correlated to fundamental strength and deformation properties such as uniaxial compressive strength, Brazilian tensile strength and modulus of elasticity of the same coal stratum. The index tests, barring Point Load Index, showed relatively low percentage scatter compared to the fundamental strength and show marked advantages for routine estimation of coal seam strength.

Jan 1, 1986

By M. Gaft, G. Panczer, R. Reisfeld, L. Nagli

Laser-induced luminescence and breakdown spectroscopy methods appear to be a good tool for real-time evaluation of dolomite content on moving belt. The distinctive feature for time- resolved luminescence is Dy3+ emission in apatite, which is excited by 251 nm laser light and detected with delay time of 5 ms and gate width of 1 ms. The distinctive features for breakdown spectroscopy are 604 nm line of F and P in apatite and 518 nm line of Mg in dolomite. The representative sampling of more than 200 pebbles has been studied by both methods. By luminescence method 100% of dolomite will be identified, while approximately 15-20% of apatite with extremely week Dy3+ luminescence may be mistakenly counted as dolomite. By breakdown spectroscopy the identification is 100% correct both for dolomite and for apatite.

Jan 1, 2002

By Indranil Roy

Gua supergene enriched iron ore deposit from Jharkhand, India has been geostatistically modeled. Population modeling shows a negatively skewed 3-parameter log-normal fit for Fe and positively skewed 3-parameter log-normal fit for Al2O3 and SO2. Semi-variographic studies for Fe indicate spherical function fit using point kriging cross-validation technique with Co=4.06(%)2, C5.11 (%)2, Co+C=9.1 7(%)2 and 'a'=348m. Kriging with 50mx50mx 10m block size at 740mRL led to a global mean kriged estimate of 61.98% and kriging variance of 4.04(%)2 for Fe with central 90% geostatistical confidence limits at 61.39% and 62.24% for that level. This led to an ore inventory at 740mRL as 7.29 million tonnes of ore.

Jan 1, 2002

By William Bergeson

This paper presents the challenges of the Homestead Avenue Interceptor Extension (HAIE) project in downtown Hartford, Connecticut. The new 72-inch (1,830 mm) sewer pipeline project consists of installing approximately 3,010 linear feet (920 m) of PVC lined reinforced concrete pipe using pressurized face microtunneling. The entire alignment is located within soft to very soft, varved silt and clay. To the extent possible, the alignment was selected to avoid bedrock, glacial till, miscellaneous fill,buried steel piles, and utilities. Challenges for this project include low ground cover, crossing major transportation routes, and limiting settlement to prevent damage to historical buildings and critical utilities. The machine was selected for the ground conditions. Design calculations were performed for selecting the reinforced concrete pipe class and for evaluating settlement. The potential for settlement damage was evaluated using both conventional analysis and finite element analysis

By S. C. Suboleski, R. Zhao

A Simulation/Animation Model (SAM) with several unique features has been developed for continuous mining in room-and-pillar production systems. Initial cut data are generated by the program based on a short list of general section parameters, and is graphically displayed on the screen for checking and editing. This portion of the program includes several intelligent features. For example, a different cut sequence will be generated for uni-directional section ventilation than for bi-directional flow. Once the data are accepted, the entire simulation may be viewed in animation. Effectively, much of the data are checked visually by watching the actions of the mining equipment. Following the simulation, results are summarized as bar and pie charts, as well as printed output. In addition to the extensive use of graphics, the program contains several advances in simulation techniques as well.

Jan 1, 1993

By D. Brosnahan, J. Gathje

Newmont Metallurgical Services (NMS) recently acquired a Scanning Electron Microscope (SEM) with a JKMRC/FEI Mineral Liberation Analyzer (MLA). With the MLA software package, raw particle image and X-ray data can be converted into particle mineral maps and bulk and liberation data can then be calculated for minerals of interest. This type of quantitative mineralogical data can then be used for a wide variety of applications. Ore characterization with MLA can be carried out for existing or processing plants in development. MLA characterization of laboratory test products provides valuable liberation information that assists the research metallurgist in better planning and developing process treatment options for various ore types. This paper describes the use of MLA characterization in a copper flotation test program where the use of various testing options for arsenic depression was being evaluated.

Jan 1, 2007

By R. Owen, T. Canty, C. Marks

The industrial vision system provides on-line 2D particle size analysis for aggregate slurries in both the overflow and underflow of hydrocyclones. This paper covers required vision system features allowing CCD cameras to function in the harsh environment of a mine milling area. The study conducted demonstrates the system’s capacity to obtain particle size distributions for controlling hydrocyclonic separators. The particle size distribution is obtained within seconds and immediately updated to allow for process adjustments. Results are then provided as a graphical computer generated display or output as a 4-20mA current loop for process control. The primary use of the vision system is in classifying particles in cyclone overflows which are often a few microns in size. Typical size information for actual mine slurry samples are presented and possible control schemes discussed.

Jan 1, 2002

Tracer gases are an effective method for assessment of mine ventilation systems, but their dispersion characteristics can differ substantially as ventilation parameters, such as flow path and velocity, vary. This research utilizes Computational Fluid Dynamics (CFD) to model a simplified full scale model mine, details a sensitivity study examining mesh size for an underground coal mine simulation, and examines gas dispersion parameters to determine the optimal model methods for simulation of tracer gases in underground coal mines. These models can be used to determine how a given tracer gas profile might be generated in a mine or areas of a mine that are not accessible, for example, immediately following a mine disaster. Accurate simulation scenarios can allow for the remote determination of the status of the ventilation network, but the sensitivity of the simulation at mine scale must be carefully examined.

Jan 1, 2012

By A. Henchiri, G. A. Gruber

INTRODUCTION Phosphatic resources may be quantified in terms of ore tons and phosphate analyses; however, to quantify phosphate reserves it is necessary to estimate the tons and quality of phosphate rock that can be extracted from the ore. The yield and grade of phosphate rock that can recovered from sedimentary phosphate deposits are usually difficult to estimate because of variations in stratigraphy and/or mineralogy. Prospecting phosphorite ores for purposes of estimating reserves and preparing mine plans requires considerably more effort than defining ore thickness and P205 content. In Florida, for example, it is standard practice to prospect by core drilling and to subject each strata (split) to beneficiation testing, and to perform detailed chemical analyses on the beneficiated products from each strata. For a completed drilling pattern the area of influence of each hole is 2.5 acres. The number of strata per drill hole typically varies from two to five, and thus complete prospecting of a 40acre tract requires drilling 16 core holes and beneficiation testing of about 48 ore samples. Florida practice is not appropriate for all phosphorite deposits. Functional drill rigs and trained drillers may not be readily available. Water for core drilling may be unavailable and the characteristics of either the overburden or ore may require careful attention and excessive cost to obtain representative core samples. Alternate ore sampling methods include auger drilling, rotary drilling to obtain cuttings, and the excavation of trenches, pits, and shafts. Drill cuttings samples are generally the least expensive to obtain, but they are usually unsuitable for beneficiation testing because of particle size reduction during drilling. Ore samples from surface trenches and pits are expensive and may not be representative of deeper ore. Ore samples from shafts are the most expensive to obtain, but if taken properly they are reliable for use in laboratory and pilot plant testing. Regardless of the prospecting technique used, reliable estimates of the yield and grade of phosphate rock that can be extracted from an ore deposit are required: • to justify capital expenditures for a new mine • for mine design and mine planning • for beneficiation plant design • for production forecasts, quality control, and marketing. This paper describes models that predict the beneficiation response of ores from three phosphate ore deposits. The purpose of these models is to obtain maximum utilization of available prospect data with the least cost. ORE DEPOSITS Simple beneficiation models have been developed for ores from three sedimentary phosphate deposits around the Mediterranean area. The first deposit, herein described as "A" ore, is located north of the Mediterranean Sea. The second deposit, designated as "B" ore, is located east of the Mediterranean Sea, while the third deposit, "C" ore, is located south of the Mediterranean Sea. Ore "C" is from the Sra Ouertane deposit in northwestern Tunisia.

Jan 1, 1993

By J. R. Patts, A. B. Cecala

"After industrial sand has been mined and processed, the finished product is typically loaded into small bags of 45 kg (100 lb) or less, large bulk bags of 454 to 1,361 kg (1,000 to 3,000 lb), or vehicles such as trucks or trains for transport to end users. As the sand is being transferred and loaded, dust can be released into the work environment, potentially exposing workers to respirable crystalline silica. A number of control technologies have been developed and utilized in an effort to reduce dust liberation during loading operations. For bulk loading into trucks or trains, the U.S. National Institute for Occupational Safety and Health (NIOSH) evaluated one of these technologies, the Dust Suppression Hopper (DSH), at two industrial sand processing plants. Results from these case studies show that the DSH reduced airborne respirable dust levels by 39 to 88 percent, depending upon the product size being loaded.IntroductionInhalation of respirable crystalline silica dust can lead to the development of silicosis, a disabling and potentially fatal lung disease. Once contracted, there is no cure for silicosis, so the goal is to prevent the development of the disease by limiting exposure to respirable dust containing crystalline silica at or below the exposure limit of 50 µg/ m3 recommended by the U.S. National Institute for Occupational Safety and Health (NIOSH, 2002). At industrial silica sand operations, the product contains high levels of crystalline silica, so effective control technologies are needed to minimize the respirable dust exposure of workers.NIOSH, in partnership with the Industrial Minerals Association–North America, published a dust control handbook (NIOSH, 2012) focused upon control technologies for industrial- mineral mining and processing operations. One chapter in this handbook discussed technologies for controlling dust liberated during bulk loading, including telescoping loading spouts, dust collection systems for loading spouts, enclosures for load-out areas and a newer technology known as Dust Suppression Hopper (DSH)."

Jan 9, 2018

By J. Sohn

The most promising near-term alternative to fuel cell driven vehicles is probably Hybrid Electric Vehicle (HEV or EV) technology. HEV technology combines the best characteristics of fuel-driven engines, electric motor drives, and energy storage components. It is designed with a combustion engine that functions as the primary power source, and an electric power storage system that functions as the secondary power source. The presence of the secondary power source allows designers to size the combustion engine for cruising power requirements. A new energy source for HEV or EV market will become lithium ion batteries (LIBs) in the near future. LIBs for HEV or EV has large scale about more 10,000 times than small size one for IT devices in order to achieve high electric density/capacity and high efficiency, etc. In those reasons, physical treatment of the batteries is more difficult for stable dismantling in comparison with the smaller one. Hybrid vehicle sales will grow by nearly 400 percent during the next seven years, according to a new report from analyst firm ABI Research. By 2013 hybrids will make up 6 percent of annual U.S. auto sales. The traction battery pack will become air-cooled LIBs which consists of several modules of Li ion battery and connected in series/parallel configuration to provide about >450 VDC, >150 kW peak power, and >80 Ah capacity. As the use of these batteries tends to increase significantly for the next years, it is relevant issues that development of new recycling methods as well as optimization of existing processes to treat spent LIBs for HEV have being addressed in order to obtain sustainability. In this study, physical treatment containing stable electrical discharge of spent LIBs for HEV was carried out for recovery of valuable metals from the batteries. Also In order to increase the yield of valuable metals through physical treatments such as electric discharge of spent batteries, crushing, and classification, we also focused on the recovery of cobalt from +8 mesh fraction due to its large portion in crushed intermediates.

Jan 1, 2010

By Lennart Mukka

The Kiruna Mine in Sweden currently has three ventilation systems. The first two (a new and old system) serve the production areas. The third system is used for the facilities on the former main haulage level 775. That area includes offices and workshops for load haul dumpers (LHD) and drill rigs. The third ventilation system also covers the crushing and haulage on level 1045. At the present time, the total airflow for the mine is 1,600 m3/sec(3.4 million cfm). The current system serves the levels above the 775 level. The new one is for the levels between 775 and 1,085 m (2,540 and 3,560 ft), which are needed for the new ore body. When all of the production is below level 775, the old ventilation system will be closed down.

Jan 1, 2002