Search Documents

By K. A. Larsen, J. L. Ariail, C. M. LaRosa

This article discusses the evolution of U.S. laws and policies towards environmental remediation at mine lands over the last 20years, the opportunities that these changes present for reuse, and the remaining challenges associated with community capacity for effective reuse planning and implementation. Emerging initiatives by the U.S. Environmental Protection Agency and Department of Interior for addressing these challenges are discussed.

Jan 1, 2004

By R. Kadeg, S. Pavlou

A methodology for developing and utilizing risk-based action levels for soils in site closures is discussed. The methodology is based on standard exposure pathway models which are consistent with current regulatory guidance on conducting risk assessment. A simple approach to evaluating the potential for contamination ground water from the projected criteria based on the Toxicity Characteristic Leachate Procedure (TCLP) is also presented.

Jan 1, 1992

By D. Malhotra

Gold and silver ores are generally leached in weak cyanide solutions for recovery of precious metals. However, pretreatment of refractory ores requires flotation to concentrate the precious- metal minerals. Also, flotation is a common concentration technique for recovering precious metals as byproducts in sulfide-mineral flotation circuits. The present paper reviews current plant practice and future challenges for precious metal recovery.

Jan 1, 1999

By J. D. Miller, C. L. Lin

A PC, image-based, on-line instrument for measuring coarse particle size on a conveyor belt is under development. The hardware and software required to implement such a system are discussed, including the interface for the special image-acquisition hardware. The system concept is given with examples to illustrate the step-by-step procedure for the implementation of image-processing algorithms.

Jan 1, 1994

By J. M. Hans, M. F. O’Connell, G. E. Eadie

INTRODUCTION The U.S. Environmental Protection Agency (EPA) was required, under Section 114(c) of Public Law 95-604, to provide a report to Congress identifying the location, and potential health, safety and environmental hazards of uranium mine wastes together with recommendations, if any, for a program to eliminate the hazards. The approach taken to prepare the report was to develop model active and inactive mines and locate them in a typical mining area to estimate their environmental impact. A list of uranium mines was acquired from the U.S. Department of Energy (DOE). The inactive mines were separated from the list and sorted into surface and underground categories. A literature search was conducted to obtain and consolidate available information concerning the environmental aspects of uranium mining and shortterm field surveys and studies were conducted to augment this information base. Radioactivity emission rates were measured or estimated for each mining category and were entered into computor codes to assess population exposures and subsequent health risks. The general environmental condition of inactive uranium mines was determined by walk-through surveys in several mining areas. INACTIVE SURFACE MINES We assumed that a model inactive surface mine contains a single pit with the wastes (overburden and sub-ore) stacked into a pile adjacent to the pit area. No credit for reclamation is given to the model mine. In lieu of the availability of individual mine production statistics, the model surface mine size was established from the total ore and waste production statistics for all surface mines, divided by the number of inactive surface mines. The number of inactive mines, obtained from the DOE mine listing, are summarized by type and location (Table 1). For modeling, we assumed that there are 1,250 inactive surface mines. The total or cumulative waste and ore production for inactive surface mines from 1950 to 1978 is not fully documented. Uranium mine waste and ore production statistics, on an annual basis, were available for both surface and underground producers from 1959 to 1976 (D0159-76). Annual uranium ore production for each uranium mining type are available for 1948 to 1959 (DOE79) and for combined ore production TABLE 1. Consolidated list of inactive uranium producers by State and type of mining [State Surface Underground AL 0 9 AZ 135 189 CA 13 10 CO 263 902 ID 2 4 MT 9 9 NV 9 12 NJ 0 1 NM 34 142 ND 13 0 OK 3 0 OR 2 1 SD 111 30 TX 38 0 UT 378 698 WA 13 0 WY 223 32 Total 1246 201T] for underground and surface mining from 1932 to 1942 (DO132-42). In order to estimate waste accumulated prior to 1959, the waste-to-ore ratios from the 1959 to 1976 period were plotted vs. time and line-fitted by regression analysis (Figure 1). Unfortunately, the extrapolation of the line to years prior 1959 approached zero in 1954 although surface mining began in 1950. Therefore, a waste-to-ore ratio of 8:1 was used for the period of 1950 to 1959 based on ratios estimated by Clark (C174). The waste to-ore ratios for 1976 to 1978 were estimated using the line established in Figure 1. By using waste-to-ore ratios and ore production data, the cumulative waste and ore production for both surface and underground uranium mining is estimated to 1978 (Table 2). The estimated cumulative waste from uranium surface mining for 1950 to 1978 is 1.73 x 109 MT. A crude estimate of the waste accumulated at the model inactive surface mine can be made by dividing the total waste produced to 1978 by the number of inactive mines. This, however, overestimates the waste tonnage because some of the contemporary wastes are being produced by active mines, and the waste accumulated at newer mines has increased in recent years. To adjust for this overestimate, we assumed that all mines operating in 1970 will be inactive by 1978. This eight year period is approximately one-half the lifetime of a model

Jan 1, 1981

By Steve Kral

Most innovations in the mining and processing industries have come from the need to produce more for less. Extracting minerals from the ground is expensive. And it is a constant struggle for mine operators to maintain the line between profitability and loss. The same holds for equipment suppliers. To maintain competitiveness, mining equipment manufacturers are building their machines with an eye to what the customer needs. Equipment makers know that if they do not supply machines that are productive and cost efficient, their competitors will. The result has been that the mining industry can now produce more ore with fewer people and more productive equipment. But, for all of the advances made in equipment, mine operators still demand machines that produce even more, are safer for workers and the environment, require less maintenance and can do the job at lower costs. And equipment manufacturers keep responding with larger, smarter and more technologically advanced machines.

Jan 1, 2005

By L. G. Hendrickson

Direct-reduction processes for converting iron ores to metallic iron in the solid state have been available for some time; and whenever scrap becomes expensive, there is a new wave of interest in these processes. It is well established that direct reduction, coupled with electric-furnace steelmaking, is a technically viable method for making steel and in some circumstances is economically competitive with the conventional blast-furnace--basic-oxygen-process (BOP) route to steel. This raises a number of interesting questions, several of which could be of great interest to the coal and ore mining industries. For example, what are the quality requirements of the raw materials for direct-reduction--electric-furnace steelmaking? Would they be different from the present requirements for blast-furnace--BOP steelmaking? Other questions relate to how much steel will be made by the direct-reduction route in the future. The quality questions can be discussed with a fair degree of certainty, but a prediction of the amount of steel that will be produced by the direct-reduction--electric-furnace route is beyond the scope of this paper. However, an attempt will be made to identify some of the factors that will influence whether there is a swing to direct reduction and the rate at which it may occur.

Jan 1, 1978

Caterpillar and Fortescue Metals Group have moved forward with the delivery, installation and support of a complete Cat MineStar System at Fortescue?s Solomon iron ore mine in the Pilbara region of Western Australia. The complete technology suite was implemented for the first phase of Solomon, the 20 Mt/a (22 million stpy) Firetail manned mine, in October 2012. As part of an autonomous mining solution for phase two, the 40-Mt/a (44-million stpy) Kings Mine, eight Command for hauling Cat 793F CMD trucks were commissioned and commenced operations in the second quarter of 2013. The mine plan calls for a progressive ramp up to 45 autonomous trucks during the next several years. In addition, other Cat MineStar System capability sets, Fleet, Terrain, Detect and Health, are being used across the mobile equipment fleet, including support equipment and light vehicles. Working closely with Fortescue and its mining contractor, Leighton Contractors, Caterpillar and the Cat dealer in Western Australia, WesTrac, are providing a full solution for managing, operating and supporting Cat MineStar System and Command for hauling. The greenfield Solomon Mine has brought together the skilled team from Caterpillar, Fortescue, Leighton Contractors and WesTrac to deliver an efficient, cost effective autonomous mining solution.

Nov 1, 2013

By L. A. Wasselle

The Israel Mining Industries Institute for Research and Development has developed, during recent years, a number of new processes for fertilizer materials. Their phosphoric acid processes, however, are capable of producing an acid of far higher quality than that normally associated with fertilizer grade acid. This paper will discuss two of these processes showing the quality attainable and the capital and operating costs for, U. S. conditions. The Standard IMI Process is based on the acidulation of phosphate rock with hydrochloric acid and involves solvent extraction for the separation of high quality, phosphoric acid from the resulting solution. The IMI Purification Process applies the same solvent extraction technique to the purification of a wet process phosphoric acid from sulfuric acidulated rock. IMI has built and operated a semi-works scale demonstration plant for the standard process. The first commercial plant was started up in; Japan in 1962. This small seven metric ton per day plant is currently producing a furnace quality acid. A larger 50 metric ton per day plant is nearing completion in Brazil. Another 50 metric ton per day plant is under design while a large plant with a capacity in excess of 150 metric ton per day is in the planning stage. Both of the latter facilities are for Israel.

Jan 1, 1966

By Richard E. Gertsch

If you believe that the goal of the space program should be a permanent, manned presence in space, then you believe in space mining. Historically, mining has been an integral part of the frontier. For the space frontier, mining is absolutely necessary. Any large-scale space facility must be built from materials mined in space. The reason is simple: the cost of getting material off the earth overwhelms all other costs. The cost of launching a pound of material from earth into low earth orbit ranges from $5000 to $10,000. Multiply this number by three to get to geostationary orbit. With the added expense of landing on the moon, an object is worth more than its weight in gold. Most space projects are impossible if materials must be hauled out of earth's enormous gravity well. For example, habitats (large structures in free-fall that simulate earth's gravity) and massive solar power satellites will take millions of tons of material to construct. Transportation economics alone dictate space as the source for oxygen, construction materials, and metals, among others. Space mining is not concerned with introducing materials for terrestrial use. The need for materials in space is infinite. The challenge for the mining industry is enormous.

Jan 1, 1991

By B. R. Pothini, H. von Schonfeldt

In underground coal mining many excavated openings have a relatively short projected life span. To ensure safety for men and materials at a minimum cost over the projected operating life, only pillars for overburden support and roof bolts for support of the openings are used extensively. Mining activity constantly changes the geometry of the mine producing load changes on the structural support members of the openings that often induce unstable deformations which can lead to roof falls or pillar failures. The paper describes how simple deformation measurements can be used to design primary and supplementary roof supports and to predict roof falls and possibly pillar bumps. Specifically, bed separations in the roof measured directly with the help of borescopes and calculated from differential convergence data are used to optimize bolt links or support requirements for chemical stabilization of mine roofs. Roof falls are predicted on the basis of admissible values for cumulative convergence between roof and floor, convergence rate, and the change of the rate of convergence. The pillar extraction operations convergence anomalies detected from contouring identify bump prone pillars, while convergence and pillar dilation determine the yield zone in a pillar to verify pillar softening and de-stressing. Manuscript not received in time for publication.

Jan 1, 1983

By Charles A. McLean

Bucketline dredges are machines for excavating large relatively unconsolidated or weakly consolidated materials from below water level. They are at the upper end of the capital cost range and the lower end of the operating cost range for placer mining machines and have digging capacities, typically, of from 100 cubic yards of bank measure material per operating hour for a shallow digging dredge carrying 2 cubic foot buckets to 1500 cubic yards per hour for a large deep digging dredge with 33 cubic foot buckets. Bucketline dredges used in the mining industry have their mineral processing plants mounted aboard the digging hull. Since dredges are high capital cost items, they require large ore reserves, typically at least ten years. Because of their high capital cost they are usually operated around the clock and for as many months of the year as weather conditions will permit. Typically a well run dredge operating year round would be expected to operate for 600 hours per month. Dredges operated in cold climates cannot operate when the weather freezes the dredge pond or the gravels, and dredges operating at sea cannot operate when high waves might batter the digging ladder against the bottom or upset the mineral extraction process.

Jan 1, 1992

Ever since A Decade of Digital Computing in the Minerals Industry was published in 1969, mining men have expressed the need for an additional reference on computer methods. It was felt such a volume should spell out the "how to" of computer applications in the solution of their problems. Computers in the minerals industry will be 20 years old when the 1979 SME Fall Meeting and the 16th International Symposium on the Application of Computers and Operations Research in the Mineral Industry (APCOM) take place jointly in Tucson, AZ. On such an occasion it was thought appropriate to publish an anniversary volume which reviewed current practices and projected what might prevail as computer methods for the future. Thus was born the idea to publish Computer Methods for the 80's. The first planning meeting for this volume took place in Las Vegas, NV, during the 1976 annual meeting of the American Institute of Mining, Metallurgical, and Petroleum Engineers. It quickly became evident that no single computer method existed to solve most mining problems; rather, mining computer methods are generally tailored to fit unique geologic, mining, and organizational conditions. Hence a format which included both the theory and practice for each of the computer applications was adopted for this volume.

Jan 1, 1979

By Y. Ye, J. D. Miller, E. Pacquet, S. Gopalakrishnan

From laboratory research activities during the past five years, it is now evident that effective flotation separations can be achieved with the high-capacity air-sparged hydrocyclone. The effectiveness of the equipment has been demonstrated on a pilot-scale basis (1 tph) for a number of mineral commodities including coal, copper, gold, and industrial minerals using a nominal 5-cm x 50-cm system with separation efficiencies equivalent to those achieved by conventional flotation machines. The high specific capacity of the air-sparged hydrocyclone (100 to 600 tpd per cubic foot of cell volume for a nominal 5 cm x 50 cm system compared to 1 to 2 tpd per cubic foot of cell volume for conventional columns and mechanical machines) makes it especially well-suited for the pro- cessing of low-grade ore. As a result of these pilot-scale successes, a number of plant-scale test programs are planned for larger-diameter units to establish wear characteristics and scale-up relationships for design purposes. The status of the air-sparged hydrocyclone technology is reviewed in the present paper, including a description of the system, fundamental considerations of flotation mechanisms, general discussion regarding the effect of control variables, and the significance of feed characteristics.

Jan 1, 1988

By P. N. Thompson

The past few years have seen the introduction of mini-computers on an increasing scale at collieries in the British coal industry. These are being used for controlling underground transport systems, coal preparation plants and fixed plant (pumps etc.); and for monitoring the mine environment and face operations.. A separate mini-computer (termed a primary computer) is dedicated to each of these functions. The overall system under which these computers operate is a common one which is applicable at all collieries. The information collected by the primary computers, other than that required for immediate control, will be fed to a secondary computer for analysis and processing. This overall concept, called MINOS. (MINe Operating System) is being developed by the National Coal Board's Mining Research and Development Establishment (M.R.D.E.). Eventually most of the data required by the system will be captured automatically. For example, the fact that a delay has occurred on a face, together with the duration of that delay, will be detected automatically via transducers link linked to a primary computer. However, the reason for that delay will, in all likelihood, have to be recorded manually. Such a system is currently under development with the first trial installations now being made.

Jan 1, 1979

By G. Konstantopoulou

Environmental degradation due to abandoned quarries is an international problem, more intense when these sites are found in urban or suburban zones, in environmentally sensitive areas or are visible from sites of special interest. Rehabilitation solutions applied worldwide, range from simple relief restoration and planting to more sophisticated site exploitation in order to serve specific social needs. The elaboration of rational rehabilitation plans for every site presupposes deep knowledge and comparative evaluation of all the parameters of the problem. In this paper, a methodological approach of rehabilitation solutions for abandoned quarry sites is elaborated, based on domestic and international experience and practice. Solutions are grouped in eight main categories. In every category the framework of prerequisites and confinements (environmental, technical, social, economic, legal) for their application in Greek quarry site is investigated. A comparative assessment of alternative restoration solutions is introduced, using tools supplied by environmental economics, cost-benefit analysis, G.I.S. and multi-criteria analysis and follows in two stages: 1) Establishment of a set of criteria aiming at a priority list for a number of quarry sites located in a geographical or administrative district. 2) Assessment of alternative solutions for every single quarry from the previous priority list for the selection of the most adequate using technical, economical, social and environmental criteria.

Jan 1, 2008

By Ehsan Alavi Gharahbagh

Tool and cutterhead wear is a crucial issue in soft ground tunneling, especially because tool inspection, maintenance, and replacement are done under difficult conditions, and often under pressurized faces or under ?hyperbaric interventions?. Overall, tool inspection and changing is a time consuming and costly step, which needs to be quantified and the related costs accounted for in any construction contract for scheduling and costing of the tunnels at design stage or bid preparation. However, lack of a universally accepted index or measure for soil abrasivity in the geotechnical reports has made it difficult, if not impossible, to define cutter wear for this purpose. Soil abrasion and its impact on cutting tools for tunneling machines under dry or wet conditions have recently been under spot light due to construction claims in several of the recent tunneling projects. The objective of this paper is to examine soil?s physical, mechanical and tribological properties related to the interface of the soil and excavation tools and discuss ways to measure soil abrasivity in a quantitative and repeatable manner. The paper will discuss the efforts that are underway to develop a new soil abrasivity index and the fabrication of a new testing device for this purpose.

Jan 1, 2010

By John Reilly

Traditional methods of project procurement of have remained virtually unchanged in the U.S. infrastructure construction industry for more than 50 years. The traditional method, Design-Bid-Build (DBB), uses a two-step process that separates planning and design from construction. Design is generally done by the public agency and their consultants and the subsequent construction contract is procured from the private sector, almost always by a “low-bid” approach. This method has worked well for many projects, delivering quality work for the lowest bid price. This is particularly true for those projects where the work, and the public agency’s management procedures, are well understood by the contracting community and there is relatively low uncertainty in the work or conditions, particularly geotechnical conditions for underground construction. However, concerns exist with the DBB process. It is time consuming because all planning and design work must be completed prior to beginning any construction work and it is of concern for complex or large projects, plus those with significant risk, where the separation of design and construction, in conjunction with pressures resulting from the low-bid environment, often result in substantial cost and schedule increases. Frequently, these increases occur in a non-productive, inefficient, adversarial work environment leading to claims, disputes and costly litigation (Quick 2002).

Jan 1, 2007

By E. Farrokh

Estimation of the cutter life and cost is a part of evaluating performance for a hard rock TBM in any project. Various approaches has been proposed for calculation of disc cutter life in various rock types based on machine specifications and rock strength and abrasivity. Cutter change time is a parameter that is used in some of the estimates and is defined as the average time required for changing a cutter on the cutter head and cutter life is the number of cubic meters of excavated rock per each disc cutter. Analysis of cutter life information of several tunnel projects from around the world has revealed that the published models for estimation of cutter consumption require some revisions to offer a more accurate prediction. The preliminary analysis of data shows that the average cutter change time is approximately 66 minutes for different cutter sizes and there is a minimal difference between corresponding cutter change times of the large (e.g. 19 or 20 in) versus smaller cutters (e.g. 15.5 to 17 in). This paper reviews the available and published cutter life data from various projects. It also introduces new models for estimation of cutter life and cutter change time as part of TBM down time and utilization analysis.

Feb 27, 2013

By Graham Davis

The future of the world's minerals industries is often painted as bleak. Peter Drucker has repeatedly proposed that the demand for minerals has become "uncoupled" from world economic growth.' This implies that, while mineral demand was in the past linked to the growing demand for and consumption of goods and services, further world development will not require substantial mineral inputs. Lester Thurow noted that for these reasons the US minerals industry is diminishing in scale and economic importance.2 There is some documented evidence of such uncoupling, and the demand for minerals may indeed diminish in the future. But such announcements are, to this point, no more than speculation. For instance, is it not just as likely that renewed environmental concerns will cause increased demand for the relatively innocuous environmental properties of metals, replacing plastics? And even if the prophesied demand decreases do occur, a sufficient fall in metal prices due to technological advances could increase the quantity of minerals demanded above current levels, in spite of leftward shifting demand curves. Thus, worldwide mineral production activity may increase or decrease in the future and no one can say whether more or fewer of the earth's citizens will become involved in the extraction and processing of minerals.

Jan 1, 1994