Search Documents

By William E. Bruce

Percussive drill calibration experiments performed by the Bureau of Mines on two drills are described. The use of a linear velocity transducer to determine piston velocity, blow frequency, and piston stroke length is discussed. Data are presented on the relationships between maximum work rate and feed air pressure. Penetration rates in nine rock types were measured for the same two drills. Physical properties of the nine rock types are presented in tabular and graphical form to show relationships between penetration rates and physical properties. Finally, conclusions are drawn as to the potential use of these data to predict percussive drilling rates.

Jan 1, 1970

By D. N. Adams, M. M. Wong, M. J. Robison

Islais Creek Contract E, a transport/storage tunnel in San Francisco, was visited on a fieldtrip during construction by delegates to the 1995 RETC. This paper is a follow-up to that fieldtrip. The project’s two tunnels are 3.7 m and 3.2 m finished diameter, 155 m and 77 m long, respectively. The contractor used 1,000 overlapping jet grout columns to pre-treat the weak Bay Mud along the tunnel alignments, then mined them with an open faced tunnel shield, eliminating the need for compressed air tunneling. This paper documents the jet grouting program and the tunneling operation used on the project.

Jan 1, 1997

By D. Rendini, R. D. Gutridge

INTRODUCTION Gwinnett County, Georgia, is a part of the rapidly expanding metropolitan Atlanta Georgia area. Located approximately 48 km (30 miles) northeast of Atlanta, Gwinnett County has a current population in excess of 600,000 and is projected to reach a population of 1,200,000 by 2025. As a part of the County’s master plan to supply drinking water for the expanding population and to increase system reliability, the Gwinnett County Public Utilities Department undertook the Shoal Creek Raw Water Intake and Pump Station Project. Figure 1 shows a vicinity map for the project. Prior to construction of the Shoal Creek Raw Water Intake and Pump Station Project the County had a single raw water intake to feed water from Lake Sidney Lanier (Lake Lanier) into a filter plant for processing into potable water. This project together with a newly constructed water filter plant provides Gwinnett County additional capacity and system redundancy to prevent interruptions to the drinking water supply. Lake Lanier is a man made reservoir with over 800 km (500 miles) of shoreline and was constructed by the Army Corps of Engineers in the 1950s for hydro electric power generation, flood control, and navigation benefits for the Chattahoochee River. Over time, Lake Lanier has become an increasingly important source of drinking water for the metropolitan Atlanta area. This paper focuses on the primary underground construction and lake tap components of the project including a 42.7 m (140 ft) deep pump station shaft 24.4 m(80 ft) in finished diameter transitioning to a 6.1 m (20 ft) finished diameter shaft, a3.05 m (10 ft) finished diameter by 19.8 m (65 ft) deep intake shaft constructed in an average of 21.3 m (70 ft) of water, and a 190.5 m (625 ft) by 3.05 m (10 ft) finished diameter modified horseshoe tunnel connecting the two shafts. This raw water intake system, in conjunction with the incorporated pump station with 8 pumps and dual1,829 mm (72 inch) pipelines, provides a system capacity of 1,091,062 m3/day(240 MGD) to two water filter plants and is expandable by the addition of pumps to1,500,210 m3/day (330 MGD). Parsons provided design and construction management services for the project. The $29.6 million contract to construct the project was awarded to W.L. Hailey &Company. Notice to proceed was given August 6, 2001 and substantial completion was achieved on January 20, 2004. Value engineering changes adopted for the project contributed to completing the project at a final cost of $28.8 million.

Jan 1, 2005

By Robert Moore Lewis

A unit for separating minerals Into two prescribed size fractions, designated as a Lewis Hydrosizer, was developed at the North Carolina State University Minerals Research Laboratory Ore samples with different mineral compositions, including coal, were separated effectively with the laboratory continuous unit Commercial size units are in operation in North Carolina and Mexico, and under construction In Norway Additional units are being built or are in the planning stage at several companies.

Jan 1, 1983

By J. B. Ackerman, C. S. Bucans

The Sunshine Mining Co. has recently started up its new silver refinery in Kellogg, ID. The new plant recovers silver anc copper values from a high grade tetrahedrite concentrate using hydro- metallurgical processes. The plant and process are both new and have gone through the initial startup phase during the first six months of 1985. The full scale plant was developed from laboratory test work. While the metallurgy of the process worked as expected, the material handling problems were difficult to over-come. As might be expected, those parts of the plant that represented available technology started up easily, while the parts that represented new technology presented the most difficulty. Topics covered in this paper include: 1) insufficient type and amount of agitation in the leach vessels, 2) discharge of a non- homogeneous slurry from the leach vessels, and 3) problems associated with very low flow rates in slurry lines.

Jan 1, 1987

By Peter J. Huck, Bruce G. Stegman, Richard E. Thill

Introduction Backfilling of mine voids is used to prevent or control the effects of subsidence on surface structures. The pumped-slurry, blind backfilling process has been successful for stabilizing ground over abandoned and inaccessible underground coal mines. This article describes the systematic evaluation of potential monitoring systems that would improve backfill monitoring technology. It also details field proof-of-concept tests that were conducted on two systems and the difficulties encountered in implementing them. Ground subsidence over abandoned mines can have devastating effects on overlying urban areas decades after the closing of room-and-pillar mines. The result may be cracked foundations, ruptured gas and water lines, broken sewers, distortion or cracking in superstructures, and sinks and potholes in the ground surface. About 32,000 km2 (8 million acres) of land in the US has been undermined for coal. According to the US General Accounting Office, 8,100 km2 (2 million acres) have undergone subsidence and another 8,100 km2 (2 million acres) are expected to subside by the year 2000. Actual figures on land affected or threatened by subsidence are probably much higher, since these estimates were based on late 1960s studies. For more than two decades, the US Bureau of Mines has been engaged in stabilizing ground in urban areas having high risk potential for subsidence costing millions of dollars. Thousands of acres have been stabilized, protecting property worth hundreds of millions of dollars. In earlier years, backfilling was by in-mine stowing in accessible mines or by gravity-feed sluicing methods in inaccessible mines. Pumped-slurry methods have been used extensively in the past 10 years. More slurry can be injected for fill from fewer injection holes over extensive areas in abandoned mines. Since this method requires fewer boreholes, there is less disruption of surface facilities. An investigation was conducted to determine the feasibility of using advanced, remote sensing or monitoring technology for application in monitoring fill placement. Specifically, the objective was to develop conceptual systems for blind backfill monitoring that require fewer boreholes and give better definition than is now possible. Blind Backfilling Methods Blind backfilling operations are conducted from the surface and do not require personnel and equipment underground. These methods are applicable to abandoned, inaccessible workings. Two categories of blind back-filling are point support, practiced by civil engineers to protect individual structures or surface facilities, and areal backfilling methods, used to protect large areas against subsidence. Point Support Methods Point support methods are usually gravity-feed systems. In general, point support methods use small volumes of expensive fill material and require a large number of boreholes within a constructed site. Because of the processed material used for back-filling and the close spacing of the injection boreholes, control and monitoring often may be accomplished by borehole cameras. Areal Backfilling Areal backfilling is conducted mainly by the pumped-slurry injection process (Fig. 1). In eastern and interior coalfields, material used is often mine refuse or flyash, both being undesirable on the surface and costly to dispose of in an environmentally acceptable manner. Hence, the use of

Jan 12, 1983

By William Reininger

Microtunneling provides a necessary solution for multiple utility crossings associated with the New York Metropolitan Transportation Authority Capital Construction Company?s (MTACC) Eastside Access Project for the Long Island Rail Road. Construction of four TBM tunnels and their approach structures at the eastern end of the project in Sunnyside, Queens required significant modification and expansion of the railroad infrastructure at this location. Maintenance of railroad traffic during project construction is a principal requirement. As a consequence fourteen (14) utility crossing segments are being installed under active traffic by microtunneling methods. Microtunnels were installed in a variety of conditions including depths, types of soils and construction restraints.

By Shosei Ph. D Serata

The Stress Control Method of mine design provides enhanced engineering control over the behavior of underground structures in comparison to conventional mine design methods. The same Method can be applied to achieve design control of surface subsidence. The basic mechanism relating undergroued deformation and surface subsidence is disclosed by mine simulations, using the REM (Rheological Element Method) computer code, whose predictions have been validated by field measurements. The key components of the underlying mechanism of surface subsidence have been shown to be the stress envelopes formed in the process of underground excavation. It has also been demonstrated that significant control of surface subsidence can be achieved by designing the geometry and timing of underground excavation to regulate the formation of stress envelopes. A field example is given in this paper to illustrate this application of the Stress Control Method.

Jan 1, 1986

By S. E. Phillipson, P. L. Tyrna

Lineament analysis, a remote sensing application for geological structures, has been criticized for reliance on subjective interpretations. The Mine Safety & Health Administration’s Roof Control Division performs lineament analyses with a technique that removes much subjectivity. Study areas are viewed on satellite images with software that allows examination under artificial sun azimuths and elevations. Extraneous lineaments are removed through successive steps of superposition, resulting in selection of the most robust linear features. Field investigations revealed a strong coincidence of joint and fault zones that were parallel with projected lineaments. The Roof Control Division’s successful identification of lineaments associated with roof falls and highwall failures has prompted some mine managers to incorporate lineament analysis as a mine-planning tool. The identification of potentially hazardous ground conditions will allow mine operators to obviate safety concerns that might otherwise adversely affect miner health and safety.

Jan 1, 2002

By J. Devon, D. L. Ewart

Long-term coal mining plans are often based on attainment of an average cost of coal. This is achieved by blending low- and high-cost coal production. Coal that is beyond the economic limit of the reserve is mined in a misguided effort to improve reserve recovery. Long-term contracts should be least cost-based and generate the best net present value from the economic reserve within the context of a rational mine plan. The selected economic reserve should he mined on a low- to high-cost basis to benefit from the time value of money.

Jan 1, 1996

By Jeffrey A. Holcomb

INTRODUCTION The passage of Comprehensive Environmental Response Compensation and Liability Act (CERCLA/Superfund) as well as the Resource Conservation and Recovery Act (RCRA) and state laws, have placed added regulatory pressures on the mining industry. These laws which focus on the regulation of hazardous substances and wastes for the protection of the public health and welfare and the environment, present the potential for tremendous financial impacts and liabilities on existing mine operators and owners and/or potential mine operators/owners. This paper takes a brief look at these laws and presents an environmental audit procedure to identify environmental liabilities prior to mine land transactions. The environmental audit approach presented is an overview of the procedures that could be used to document, evaluate and inventory existing and/or potential environmental concerns. This audit procedure can be applied to developed or undeveloped properties and at active or inactive mining sites. REGULATORY OVERVIEW Mining environmental liabilities have been addressed in RCRA, Superfund, the Clean Air Act (CAA) and the Clean Water Act (CWA). Even though the U.S. Environmental Protection Agency (EPA) has determined that mining wastes will be treated as solid wastes under RCRA and not as hazardous wastes, these wastes could still bring about a great deal of financial liability under Superfund. The catch is if the mine wastes generated contain hazardous substances such as the heavy metals arsenic, beryllium, cadmium, chromium, copper, lead, mercury, nickel, selenium, silver, thallium, zinc and others as well as cyanide. Thus, it is not only important for a mine operator/owner or a potential mine operator/owner to know if the mine wastes generated are hazardous, but it is important to know if the wastes contain hazardous substances. Following is a brief overview of RCRA and Superfund and their potential implications. RCRA RCRA, which provides the basis for the regulation of solid and hazardous wastes, is applicable to active mining and milling sites. Within RCRA the definition of a hazardous waste is provided. This definition applies to owners and operators of mining and milling sites if the operator has stored, disposed or treated hazardous wastes on-site. If this is the case and if strict process control and waste management activities are not adhered to, environmental liabilities may be associated with the site. Superfund The 1980 Superfund law can be applicable to inactive mining sites or to inactive sections of an active facility. The provisions of Superfund call for the regulation of hazardous wastes and hazardous sub- stances disposal and release not only by the existing owner, but also for any previous owner. This concept of joint and several liability means that one party, as among many, can be held totally responsible for the costs of hazardous waste cleanup (Haller, 1987). Furthermore, liabilities under Superfund have also been applied back to past acts; thus, several mining properties, active or inactive prior to the 1980 Superfund law, are at risk of being placed on the EPA's National Priority List (NPL) for cleanup. Last years amendments to Superfund, known as the Superfund Reauthorization Act of 1986 (SARA), provided some significant developments for the mining industry. The major requirement of the amendments as it pertains to owners or operators of mining sites is that the EPA must revise its present Hazard Ranking System (HRS). This is important be- cause in most cases the primary reason for several mining sites having been included on the NPL was due to the large volume of wastes generated. As is typical at most mining sites, large volumes of low toxicity wastes are generated and the current HRS model prejudices against this. It should be noted that this provision only applies to sites that are not already on the NPL or have not been proposed for inclusion on the list.

Jan 1, 1987

By T. Tamagawa, N. S. Fu, I. Iwasaki, M. Kobayashi

A 3-stage fluidizing bed process of chlorination, selective oxidation and sulfur chloride conversion was tested for processing of a chalcopyrite concentrate. It was found that the use of excess oxygen was essential to a stable operation in the oxidation reactor. The oxygen-excess gas will inevitably cause the oxidation of the sulfide concentrate in the chlorination and sulfur chloride conversion reactors. A new flowsheet is proposed to separate the chlorination and the selective oxidation steps with separate flow paths of the fluidizing gases, thereby preventing the passage of oxygen-excess gas in the chlorination and sulfur chloride conversion reactors. The feasibility of the proposed flowsheet was demonstrated in a laboratory-scale fluidizing bed setup.

Jan 1, 2000

By R. Larry Grayson, Joel R. Warneke

The mining industry has searched for a message that will resonate with the public while focusing on the industry’s positive contributions to society. So far, environmental groups remain unconvinced and the public is still largely uninformed. In the authors’ opinion, a number of recent events and experiences have converged to help shape a more effective public communication on mining’s important role. This article presents a perspective on coal’s role in sustaining society by anchoring the message in a transparent way, including a material flow analysis, that links coal’s impacts across a range of social and environmental aspects. Past and continuing image problems In her 1994 paper, Nancy Bingham, with Caterpillar, outlined what the public thought about mining. Based on extensive interviews, the following results were found: • The public believed mining harms the environment. • The public believed mining harms people in nearby communities. • The public believed mining exploits workers. • The public believed mining has little personal benefit to the individual.

Jan 1, 2006

By M. C. Roberts

As nations advance through various stages of economic development, the patterns of demand for minerals change. For example, as a nation develops from a subsistence economy through industrialization and into a service based economy, the use of minerals is at first low, then grows rapidly, and finally stabilizes. The past trends in the use of agricultural minerals by the currently advanced nations provide a pattern that the world as a whole may follow as it progresses through the stages of economic development. Future needs for agricultural minerals are estimated using this approach.

Jan 1, 2001

The Subtropolis mine is a room-and-pillar mine extracting the Vanport Limestone near Petersburg, Ohio. In February 2018, mine management began implementing a heading reorientation to better control the negative effects of excessive levels of horizontal stress. The conditions in the headings improved, but as expected, stressrelated damage concentrated within crosscuts. The mine operator has worked to lessen the impact of the instabilities in the outby crosscuts by implementing several engineering controls. With the implementation of each control, conditions were monitored and analyzed using observational and measurement techniques including three-dimensional (3-D) LiDAR surveys.

Jan 7, 2020

By Scott Chesman

Increased TBM performance is leading the way for resurgence in tunneling activity in NYC. Tunnels will be excavated in the same geologic formations as previously excavated D&B tunnels whose construction records are providing valuable insight into the prediction of rock mass behavior. This report compares an eight mile stretch of NYC Water Tunnel #2 with the recently excavated eleven mile stretch of the TBM driven Water Tunnel #3. Comparisons of the type and amount of rock support installed as well as water inflows and grout quantities are made. Rock mass characteristics specific to TBM performance are also evaluated.

Jan 1, 2005

By Frederik P. Agterberg

Mineral exploration consists of the acquisition of data and their interpretation to ascertain the presence or absence of uncertain events. In general, the amount of uncertainty decreases during exploration when targets become increasingly well defined. Decisions on further exploration and whether or not mining should be commenced are based on new information using both objective facts and subjective reasoning. Computers play an important role during all stages of exploration. Three recent books (References 1-3) on decision-making in exploration and mineral-resources evaluation provide additional background supplementing the papers in this volume and articles in scientific journals or other conference proceedings (e.g., References 4 and 5) dealing with the subject. Other new developments to be considered are that microcomputers are becoming increasingly important in the earth sciences (Reference 6), and so are applications of artificial intelligence (Reference 7). Microcomputer- based technology allows rapid communication between field parties and main office. Expert systems are becoming increasingly sophisticated aids for mineral exploration an can now contain objective rules based on statistical theory (Reference 8).

Jan 1, 1989

By C. B. Rash, W. W. Fowler, Gill Montgomery

INTRODUCTION Fluorspar is the common term used for the mineral fluorite, which is naturally occurring calcium fluoride (CaF2). It is the principal source of fluorine, the most reactive of the chemical elements, from which a great variety of unique and strategically important chemicals are produced. Commercial deposits of fluorspar are widespread throughout the world, and its availability is essential to the industrial progress of all nations. GEOLOGY AND MINERALOGY In its pure form fluorspar, CaF2, contains 51.1% calcium and 48.9% fluorine, and has a sp gr of 3.18 and a hardness of 4. It is commonly a glassy mineral. colorless, white, or grayish. but may also be various shades of purple, pink, blue, green, yellow, or tan. It belongs to the cubic system mineralogically, and commonly crystallizes into cubic shapes in vugs and cavities, although most of it is massive, with interlocking crystals. Minable fluorspar deposits, in descending order of importance, occur as bedded limestone replacement deposits along fault zones; fissure-filling vein deposits; breccia filling in limestones, dolomites,

Jan 1, 1985

By Khosrow Badiozamani

Traditionally the mining industry has been lagging in application of computers in their daily or long range plan activities compared to other industries. The question then remains as to how the technology of higher computing capacity for less cost is going to affect the mining industry and how the lukewarm reception of engineers in acceptance of computerized mine planning in the past is going to change because of the new wave of high techology. These questions and the reasons for the lack of usage of computerized mine planning systems by engineers will be evaluated in this paper. In addition, alternatives available to the mining industry will be analyzed and the direction of the future "user friendly" software will be discussed.

Jan 1, 1984

By K. A. Prisbrey

Mineral carbonation is the reaction of carbon dioxide with mineral silicates to form solid, carbonate compounds. The carbonate ion holds carbon in a low energy state – lower than in carbon dioxide. Thus the reaction of carbon dioxide to produce mineral carbonates captures the carbon in a stable, solid form. The University of Utah is investigating the carbonation of silicate minerals by mechanochemical processing, which has the potential of being much less expensive than other methods. Tests to date have shown that a marked change takes place in the lizardite variety of serpentine after 15 to 20 minutes of intense grinding in the presence of gaseous CO2. Further testing is in progress.

Jan 1, 2004