Search Documents

By Marcel Haffen, Jean Janin

The purpose of grouting is to modify the permeability and strength characteristics of the subsoil in such a way that the planned structure can be efficiently constructed at a given location. This technique, which originally underwent considerable development in the field of dams construction is constantly evolving and it becomes more and more important in urban zones of intensive underground development for projects such as transport tunnels, stations, car parks, ect. Grouting becomes more and more indispensable whatever the natural characteristics of that subsoil ; such is the case particularly when the planned work runs through cohesionless granular soils, usually water-bearing such as alluvium, sands, disturbed ground, fill material, etc. The selection of the grouting method and the extent of treatment required at depends on two fundamental factors. 1º) nature and behaviour of subsoil to be treated. There is no need to stress the necessary of a good knowledge of geotechnical, hydrological and chemical characteristics of the ground to be treated. At the present time the specialists in these fields have available numerous methods of analysis, either laboratory or field tests, which enable to evolve a suitable treatment.

Jan 1, 1997

By L. M. Chan, D. H. Carlson, J. H. Johnson

This paper discusses laboratory evaluation of a tailpipe emissions measurement apparatus (EMA) developed by Michigan Technological University (MTU) under contract to the Bureau of Mines. The apparatus dilutes diesel exhaust and measures the concentrations of diesel particulate matter (DPM), CO, C02, NO and NO2 at known dilution ratios. The EMA was evaluated by side-by-side comparison of its measurements with those by laboratory grade instruments. During the preliminary laboratory evaluation concentrations of DPM, CO and CO2 were measured. The concentrations of CO and CO2 measured by the EMA were usually within ±14 pct of laboratory-measured values for CO and ±20 pct for CO2. EMA DPM concentrations correlated well (r = 0.96) with the laboratory values, but were 29 pct lower on average. The CO and C02 differences were observed to be related to the method of calculating the EMAs' dilution ratio and the difference in DPM concentrations is attributed to thermophoretic and/or condensation losses related to the EMA's unheated sample probe. Preliminery analysis of data obtained with a heated sampling probe and modifications in the sampling procedures have indicated reduced variability in DPM and in the calculated dilution ratios.

Jan 1, 1991

By E. Pardo-Igúzquiza

Most mining applications of geostatistical simulation are to the simulation of quantitative variables, such as grade. In many instances the occurrence of quantitative variables and the values they take are controlled, at least partially, by qualitative, or categorical, variables. Examples include quartz-vein controlled gold orebodies and stratigraphic silver/lead/zinc deposits. In these cases a realistic simulation must include geological controls on the spatial distribution of the simulated quantitative variables. This paper describes extensions to, and algorithms for, the truncated plurigausian method of simulating categorical variables. The categorical variables are modelled as indicator random functions that represent the presence/absence of the variable at spatial locations. Stochastic images of the distributions are obtained by truncation of realisations of two Gaussian random functions simulated at the same locations. Parameters required are the thresholds for truncation of the Gaussian variables and the covariance structure of each Gaussian random function. These parameters are estimated from the experimental proportions of each variable and indicator direct and cross semi-variograms. A detailed case study is shown in order to illustrate the procedure, to discuss the results and to present the algorithms for plurigaussian simulation.

Jan 1, 2002

By G. S. Austin, L. A. Brandvold, J. Renault

A series of tests were run on soil samples collected near the site of a Socorro, NM lead smelter that was abandoned more than 98 years ago. Three 30.5- x 30.5-m (100-X 100-ft) squares provided 13 samples each. As described in Part I (this issue), each sample was divided into seven splits according to particle size. A mineralogical examination of the fine-size fraction of Pb-contaminated soils failed to reveal crystalline Pb compounds. These authors conclude that Pb is present as amorphous phases or is adsorbed on the surfaces of soil particles. Site vegetation contained elevated Pb levels that increased with increasing Pb amounts in the soil. However, the biological absorption coefficient (BAC) indicates that some of the site's Pb is unavailable, or the plants are able to limit their uptake. Of the vegetation tested, rabbit bush showed the greatest increase of Pb levels in its roots, whereas levels in creosote were highest in the foliage. In cactus, the Pb levels varied. The amount of Pb due to dust incorporated in plant tissue is almost negligible compared to the amount absorbed through the plant vascular system.

Jan 1, 1994

By Edwin H. Bentzen, Immo H. Redeker

Important industrial minerals are separated and concentrated by froth flotation by industry today. The following descriptions are presented as an overview of the methods employed to separate and recover a few of these industrial minerals. The minerals described in this section of the book are not, by any means, the only important minerals treated by froth flotation. Other minerals, such as calcite, kaolin, wollastonite, rare earths and vermiculite were not included, primarily due to the confidential nature of the information held by the Minerals Research Laboratory and the Colorado School of Mines Research Institute. Flotation of nonmetallic minerals is sometimes viewed as alchemy. However, the art is, in reality, based on sound chemistry, experience and a little luck in the treatment of new ores. In the flotation of nonmetallic minerals, as opposed to base metal sulfides, highly specific treatment conditions are required to accomplish separations. The presentation of the treatment of each of the minerals described was outlined as follows: DEPOSITS PROCESSING SPECIFICATIONS FLOWSHEETS (in some cases) A presentation of the factors, often critical, which must be carefully investigated to accomplish successful flotation of nonmetallic minerals is presented in the section on Sulfonate Collectors, elsewhere in this volume.

Jan 1, 1986

By Paul E. Richardson, Edwin E. Maust

Cyclic voltammetry and surface potential (photovoltage) measurements have been carried out on galena electrodes in sodium tetraborate solutions with added HC1 and NaOH to adjust the pH over the range 2 to 13. The first technique shows that the surface species formed on moderate anodic polarization and reduced on subsequent cathodic polarization are the same over the entire pH range. At anodic potentials, a soluble metal species and excess sulfur are formed; at cathodic potentials, sulfur is reduced to a soluble species. More importantly, excess surface sulfur is formed spontaneously under zero current conditions in alkaline solutions. This has been shown to occur on both polished surfaces and on virgin surfaces produced by in situ cleavage under the electrolyte. The photovoltage gives some insight into the charge and potential distribution at the galena surface. This is found to depend on past electrochemical history and the n- or p-type semiconducting character of the electrode and is interpreted in terms of changes in the surface stoichiometry that occur during reduction or oxidation. The effect of surface stoichiometry on subsequent xanthate interactions is discussed.

Jan 1, 1976

By K. Konialis

In the last twenty years, the mining industry has made marked efforts to improve its reputation in regard to its social performance. These efforts have been expressed in the 9th ICMM (International Council on Mining and Metals) principle as a commitment to contribute to the social, economic and institutional development of the local communities. Towards this goal, which has been increasingly highlighted because of its importance for sustainable development, a number of practices and methods have been developed. The international development literature describing these practices is full of so-called development buzzwords, such as stake-holder participation, empowerment, capacity building. This paper argues that none of these development catchwords are neutral, but contain assumptions based on a specific view of development. Since capacity building is a central task in development, the paper focuses on this concept and takes a critical look at the assumptions that underlie this concept and influence strategies employed by the mineral sector. It suggests that the notion of capacity building in some earlier approaches implies a set of asymmetric power relationships between developed and developing countries where capacity is transferred from the developed countries to the developing ones. The developing countries are seen as passive recipients while the experts, i.e. the developed countries through their mining companies ultimately control the capacity-building process. The paper also points out that the mainstream capacity development approach has been based on the assumption that local or indigenous communities are mainly made up of needs and capacity gaps. The goal of development projects should then be to address these needs, which are perceived and prioritized by the ?experts?. Critiques of this development model suggest that in order for the mining industry to embrace more successful and sustainable practices, it should rethink the notion of capacity building. It should move towards alternative approaches that see it as a two-way learning process which will serve to enhance not only the capacities of the communities, but also of the development practitioners and which will build on the strengths of the community, and move away from attitudes of superiority and practices of dependence.

Jan 1, 2007

By W. Holding

Since the 1975 International Mine Ventilation Congress in Johannesburg there has been a trend in South Africa towards making the mine ventilation departments responsible for monitoring the total environment. This includes the taking of noise and illumination measurements and there is in fact a debate taking place as to whether the departmental title should be changed to 'Environmental Control Department'. The organisers of the 2nd international Mine Ventilation Congress have decided that noise and illumination will not be included as Congress subjects and 'Total Environment' includes only those facets which are open to debate at the Congress. The choice of mine is significant in that while most Congress papers from South Africa will be devoted either to coal mining or to the somewhat unique deep level gold mines, Prieska Copper Mine is a mine which can easily be identified with similar mines in many other parts of the world. The mine is situated some 750 km south west of Johannesburg and about 600 km north east of Cape Town. Current production (ore and waste) is about 340 000 tons per month and the total underground labour force is just over 2 000. The ore body is a massive sulphide, the main minerals being copper and zinc and the method of mining is sub-level open stoping. Daily average surface temperature conditions range from 85°F (29.5°C) dry bulb and 69.8°F (21°C) wet bulb in mid-summer to 42°F (5.5°C) dry bulb and 36.5°F (2.5°C) wet bulb in mid winter. The information presented in-this paper is limited to what can be gathered by mine ventilation staff as part of an on-going exercise and is obviously not as comprehensive as would be the case if a fully equipped research establishment were to become involved. The paper will be divided into three sections 1) Gases 2) Dust 3) Heat In each section statutory and/or other standards will be set down followed by a discussion of assessment and in some cases control methods.

Jan 1, 1980

By Don Morris

The Building Products Company is Phoenix based and owned by Mission Clay products of California. Building Products is the only manufacturer of vitrified clay pipe in Arizona. The marketing area includes Arizona, Nevada, Utah, New Mexico, and California. Building Products, promoted by Arizona Public Service, was formed in 1970. Raw-materials prospecting was undertaken for 2 years, after which a $5-million plant was built. Initially, a satisfactory vitrified product could not be made with the raw materials then in hand. Subsequent prospecting and testing led to an acceptable raw-materials mix. Testing to upgrade the final product is a continuing process. The basic raw-materials supply must be adequate, secure, and capable of sustaining close tolerances in the final product. These needs are met by mining four geologic materials at three different localities: (1) refractory aluminous shales (two horizons-one pit) Colorado Plateau Province (Mogollon Rim); (2) less refractory aluminous materials from late Cenozoic lacustrine materials near Dewey in the Transition Zone (TZ); and (3) Precam¬brian "slate" from near New River along the southern edge of the TZ. Other additives include grog (ground-up, broken pipe) and barium carbonate that ties up what gypsum there is. Calcium magnesium carbonates are deleterious components that are minimized by careful selection of the mined products. The raw materials are blended and mixed, ground to 12 mesh, mixed in a pug mill, depleted of air, extruded into pipe ranging from 6 inches to 42 inches in diameter, transported to a hot-air drying room, fork-lifted to an appropriate kiln, and fired at a 1900-2000° F range. The "Rim" kaolinitic shales, being the most refractory ingredient, stabilize the pipe during the firing process. They are very plastic, and therefore facilitate extrusion. The Dewey clay fuses at a low temperature and forms an impervious glasslike binder. It also is plastic. The "slate" forms platy particles that tend to orient themselves during laminar flow. This provides strength for both the green and dried product. It doesn't absorb water, which helps the drying process. Grog remains stable during firing, and therefore helps to control shrinkage. The development of appropriate raw materials and proper mixtures has been done empirically.

Jan 1, 1987

By A. P. Cook

Methane drainage on a mine-wide scale is a relatively new technology to South African coal mines. Shallow seams and apparently low methane contents have been assumed to result in less methane problems than experienced in other countries. The introduction of deeper mines however, has now resulted in methane drainage taking on a higher priority. Methane contents in the region of 12 m3\t have resulted in one colliery introducing drainage as a ventilation support. Although a low seam permeability initially indicated reduced potential for drainage, early borehole flows of 90 m3\m\year have since increased to 450 m3\m\year. Rapid inflow of methane into goafs and sealed areas from seams surrounding the main production seam at another colliery have warranted extensive evaluation of the methane properties of these seams with the projected introduction of predrainage from surface. Methane pressures in excess of 1000 kPa and contents in the region of 10 m3\t again give methane volumes suitable for drainage. Coal seam drainage ahead of mining is becoming more significant and is likely to see an increase in the near future. INTRODUCTION Methane gas is an everpresent hazard associated with underground coal mining. Safe working levels of methane in the mine atmosphere are normally maintained by ventilation practises, ensuring sufficient dilution of the gas. However in some cases the ventilation must be assisted by methane drainage, either from the mined seam, or from adjacent seams and strata, or from goafed areas. South African collieries have practised only limited methane drainage until now. Relatively shallow mining depths, and apparently low in-seam methane contents have been assumed to result in fewer problems with methane than are the normal for other countries. This is now being shown to not necessarily be the situation. Work carried out by the Coal Mining division of COMRO (Cook and Erwee, 1991) indicates South African production coal seams have very similar methane retention properties to those of coals in other countries, with seam gas contents of up to 12 m3/t. This awareness, as well as greater mining depths, and higher degrees of mechanisation, has resulted in higher priority being given to methane emission problems throughout the industry. Increased levels of safety, as well as possible commercial applications, are the main reasons for the interest now being shown in methane drainage. Not only is there possible applications in the present production coalfields, but South Africa has vast areas of coal reserves which are presently non-mineable, now being seen as possible alternative energy sources. Limited methane drainage is practised within the industry, but only on collieries that have identified specific methane problems that can be alleviated by drainage. Historically this has been restricted to surface drainage of longwall goafs, reducing emissions onto the faces. More recently, horizontal in-seam holes have been drilled, until now for bord and pillar sections, but the results are being evaluated for later application to shortwall faces. Adjacent seams pose problems at some sites and vertical and cross measure boreholes are now being considered.

Jan 1, 1993

By E. Cameron

Yeelirrie lies toward the center of Western Australia, 650 km (404 miles) northeast of Perth (Fig. 1). The ore reserves have been estimated as 52.5 kt (57,871 tons) of contained U3O8, at an average grade of 0.15%, of which almost two-thirds average 0.24% U3O8. the ore body is a thin, elliptical, more or less horizontal sheet measuring approximately 9 km (5.6 miles) in length, between 0.5 and 1.5 km (0.3 and 0.9 miles) in width, and up to 7 m (23 ft) in thickness, extending from the surface to a depth of 8 m (26 ft). In spite of its near surface position, there is only one small outcrop of significant mineralization. Carnotite is the only uranium mineral recognized so far, dispersed through a calcrete horizon, and deposited from circulating ground water which was also responsible for the carbonation of the clays completely filling an Early Tertiary drainage system. Calcrete, as seen at Yeelirrie, is quite distinct from the widespread, thin pedogenic horizons, as it often forms bodies many kilometers in length and up to 20 m (65.6 ft) in thickness, elongated parallel to the drainage lines. It is variously referred to as "valley calcrete" or "ground water calcrete" to emphasize the occurrence and mode of origin. The discovery of Yeelirrie in mid-1971 was the successful culmination of a grass-roots exploration program initiated in 1968 as part of Western Mining Cop's program of diversification from its historical position as a major gold producer. The object was simply to find an economic uranium deposit - with no constaints other than those normally taken as applying in the mineral search. There was, therefore, complete freedom in the selection of the exploration model, or models, to be applied and the areas to be considered, though the choice was inevitably influenced by both the nature of world occurrences and the local geology. One of the options avail- able was the sandstone environment. Yeelirrie was the direct result of pursuing this line of investigation through three sequential, but quite distinct, stages: first, a regional study; second, establishing a case for exploring the inland drainage systems of Western Australia; and finally, an evaluation of the calcrete environment. An assessment of the potential for sandstone-type deposits in Australia necessitated going back to first principles, since there were no known precedents in this country for guiding exploration and, as a consequence, the search need not be influenced by established prejudices. Previous uranium exploration during the 1950s had been preoccupied with vein-type deposits, and, although the sandstone environment was undoubtedly being examined in 1968, no discoveries had been announced to that time. When considering the necessary ingredients -a source of leachable uranium, a circulating ground water system, and a suitable reducing environment - it could be argued that considerable areas in the eastern part of the continent were theoretically prospective, but basin depth and the extensive superficial cover of Mesozoic and Cainozoic sediments presented considerable practical difficulties.

Jan 1, 1991

By W. R. Bruce, R. W. Wittkopp, R. L. Parratt

Introduction The Relief Canyon gold deposit is about 24 km (15 miles) east of Lovelock at the south end of the Humboldt Range in northwestern Nevada. The deposit, is in the Relief-Antelope Springs mining district, which has historically produced silver, antimony, and mercury. There is, however, no mention in the literature of commercial gold production. Fluorite prospects at the gold deposit site have had no reported production. At Relief Canyon, the Late Triassic Grass Valley formation overlies and is in fault contact with the Late Triassic Natchez Pass formation. Epithermal disseminated gold mineralization is found within the various types of fault breccia between these two formations. Geology The Natchez Pass formation of Late Middle to Late Triassic age is composed of more than 300 m (985 ft) of massive gray to dark gray locally carbonaceous dolomitic limestone. Some minor beds of shale and siltstone up to 1 m (3 ft) thick are found in the project area. The limestone is locally silty or sandy. The color of this formation below the oxidation base ranges from gray to black and appears to be a function of carbon content. The Grass Valley formation of Late Triassic age is composed of more than 200 m (655 ft) of interbedded units of thinly parted argillite, hard gray to brown quartzite, siltstone, and shale. Within the oxidation zone, these units are olive gray. A few beds within this formation are slightly calcareous and a number of sections, especially those containing shale, are dolomitic. Below the oxidation zone, the quartzite beds are often slightly carbonaceous and the argillite, siltstone, and shale beds are often highly carbonaceous, giving them a black color. Two types of intrusive rocks have been recognized at the Relief Canyon deposit. Both appear to predate mineralization. Fine to moderately fine grained quartz monzonite dikes, up to 3 m (10 ft) thick, were encountered in several drill holes. In a number of intervals, these dikes have undergone either propylitic or argillic alteration. The age of these types of dikes is not known. It appears, however, that they are either Jurassic or Cretaceous. No gold mineralization has been found in this type of dike. Diabase dikes were also encountered in a number of drill holes. These dikes have almost always been propylitically altered. Although the exact age of the diabase dikes is not known, they are probably equivalent in age to the quartz monzonite dikes. Quaternary alluvium is found forming fans at the base of steep slopes and as recent fill in present day drainages. The alluvium is composed of either Natchez Pass limestone or Grass Valley quartzite and siltstone, depending on which unit served as the bedrock source. A significant portion of the Relief Canyon deposit is covered by Quaternary alluvium. Figure 1 shows a generalized geologic map of the Relief Canyon area. At the deposit's site, the Grass Valley formation appears to have been thrust over the Natchez Pass formation. The age of the thrust is probably correlatable with the Nevadan Orogeny, which gives it a Jurassic-Cretaceous age. The general strike of the thrust, referred to as the Relief Fault, is in a northwest direction. The strike of the bedding of both the Natchez Pass and Grass Valley formations roughly parallel the strike of the Relief Fault. The general dip of both the Natchez Pass and Grass Valley formations is in a southwest direction. The general dip of the Relief Fault, in the area of the Relief Canyon gold deposit, varies and has the appearance of a northeast-southeast striking anticline that plunges in a southwest direction. A small fold perpendicular to the plunge of this anticline forms a dome over the southerly portion of the Relief Canyon deposit. A number of northeast and northwest trending normal faults slightly offset the Relief Fault. Because of their small displacement, they are not shown on the generalized map. Gold Mineralization Gold mineralization occurs along the highly brecciated fault contact between the Natchez Pass and Grass Valley formations. Weak gold mineralization often occurs up to 2 m (6.5 ft) above the thrust in the Grass Valley formation. Most of the ore grade mineralization, however, is present below the Grass

Jan 11, 1984

By Mary Fu, Helen Leung, Colin R. Phillips

In uranium mines, the median size of the aerosol has been found to be about 0.1 micron or less. Such small aerosols are readily deposited or "plated-out" on dosimeter interior surfaces resulting in the recording of a low dose. The "plate-out" properties of the CEA alpha dosimeter head are described with respect to aerosol properties in controlled experiments in the laboratory. A simple model is derived to estimate the amount of "plate-out" in the CEA head.

Jan 1, 1981

By I. M. Eitani, M. Karmis

Ground control presents the most serious problem in underground thick seam mining. In addition to parameters such as depth thickness and inclination of the seam and nature of the coal and the immediate strata, the stress interactions caused by the mining sequence must be carefully evaluated and understood, if safety and productivity objectives are to be fulfilled. In this paper, the most widely-accepted thick seam coal mining methods are reviewed and suggestions are made for future work pertaining to ground control problems.

Jan 1, 1981

By Don Stainbrook

Over a period of many years a highly automated computerized system of ore control has been developed at the Newmont Gold Company, (NGC). It is the purpose of this paper to review the development of this system, describe the setting in which it functions and to mention some of the future developments and enhancements. Discussion of the evolution of the system in a historical perspective helps to understand its present status and illuminate some thinking about future directions of development.

Jan 1, 1989

By Yongqin Zhang

A single bubble released into surfactant solution first accelerates, reaching a maximum velocity then decelerates to reach a terminal velocity. Modeling this "velocity profile" is fundamental to understanding the motion of bubbles in flotation systems. This contribution considers the terminal velocity. Modeling is by a combination of the Navier-Stokes equation for flow around the bubble and the Marangoni effect induced by surfactant on the bubble surface. Numerical simulation is shown to agree with experiment for bubbles in pure water and surfactant solutions.

Jan 1, 1999

By J. D. Miller, C. L. Lin

The appropriate software and hardware necessary to adapt an X-ray CT analyzer for the determination of coal washability was developed and successfully tested for well-characterized samples under laboratory conditions. Evaluation of the CT-based analyzer under simulated on-line conditions is also presented to verify the on-line capabilities of the newly developed X-ray CT analyzer for the control of coarse coal cleaning circuits. The investigation shows that the data obtained from CT washability analyses compare favorably with experimental sink float data. Further, image frequency was considered to evaluate the CT-Based coal washability analyzer for simulated on-line conditions. Specifically, the number of observations (image spacing) needed for accurate sampling and the total time required to perform the calculations for a representative data set were determined. Key words: Coal washability, Computer simulation, X-ray CT analysis

Jan 1, 2003

By Johann Knecht

Due to lower specific investment and operating costs the tendency towards large scale equipment will remain. For the design engineers not only the stresses in the mill structure and manufacturing are of importance but also transportation to and erection on site. A scale up of the design of smaller sized units on the pantograph principle may not always give the best approach to the job in this respect. This paper covers recent developments in the design of large size equipment where the huge dimensions call for designs being different to the well known ball and SAG mill concept with cast conical endwalls. The first part describes the features of the biggest ball mill in the world, whereas the second part provides some details of the largest shell supported SAG mills being currently in the manufacturing process.

Jan 1, 1993

By Lane White

This is a truly exciting time in surface mining technology. A revolution is coming - a revolution made possible by complete mine management systems working in concert with many devices currently available or in the prototype stage. By the turn of the century, the face of surface mining will indeed be different. Imagine . . . an operatorless drill moving around a blast pattern drilling off rounds in record times ... a satellite-based positioning system and drill data combining to report diggability to a shovel operator based on the position of his shovel in a blast ... a driverless truck warning central dispatch of an impending mechanical problem and being reassigned to the shop ... an infrared detector diagnosing the problem, for which the mine management system generates a maintenance work order and, once the problem is corrected, re-dispatches the truck to the optimum shovel.

Jan 1, 1994

By M. García-Vásquez

In Peru, the third destination in worldwide exploration based on expenditure, mining conflicts have spread dramatically over the last decade. Mining companies need to create new initiatives to avoid social conflicts and strengthen the social capital needed to keep mining in a country with proven mineralogical riches. This document provides information about a research project that explored the opinions and experiences of a resource many times overlooked by companies: the human resource. Over 30 surveys were conducted among professionals working at mines in the Peruvian mining industry, in different departments and from different organizational levels. Mining employees acknowledged that they play an important role in the development of company-community relationships and gave their impressions about initiatives implemented by international mining companies in Peru. Mining employees also provided their recommendations to succeed in a location where cultural differences have not been properly considered.

Jan 1, 2011