Search Documents

By K. Rushdi, B. E. Abulnaga

The conventional Froude number is blind to the presence of solids, their density and their concentration in a stream of slurry mixture such as tailings flowing in an open channel. This often leads to rough approximations of subcritical, critical and supercritical regimes, based on one phase flow Froude number, limiting subcritical to a value smaller than 0.8 and supercritical to values above 1.4, as proposed in the past by Green, Abulnaga and other authors. While acceptable for small flows, such approximations can be uneconomical for the larger flows encountered in some modern plants that treat up to half a million t/day. A review of concepts of a densimetric Froude number sheds some light on the effect of solids on stratification prior and subsequent to a hydraulic jump. While the approach is heavily borrowed from modern sedimentology, it provides a useful tool to designers of large launders or open channel tailings systems. These concepts are reviewed with some practical examples.

Jan 1, 2013

By Joseph L. Walker

INTRODUCTION In looking over the diversity of the papers that are being presented during this meeting on The Industrial Practice of Fine Coal Processing one cannot help but be impressed with the progress the industry has made in beneficiating fine raw coals, and in the number of innovations that are under study to increase recovery and to improve the quality of the finest size particles produced at a preparation plant. Those who are not in our industry, who look at the technical program, might be confused, when they see that the papers include such topics as cleaning to zero and heavy media cyclone cleaning 28M x 100M; application and performance of fine coal jigs, tables, hydrocyclones, spirals, and flotation; filtration, dewatering and thermal drying; and ancilliary aspects such as fines handling, instrumentation and process control plus screening and liberation. This is an observation and not a criticism of the diversity of papers being presented. The program fits within the parameters of fine coal preparation as the term "coal preparation" is defined, but perhaps not as the term "fine coal" is defined. Admittedly these definitions are sometimes loose. However, each should be made more definitive if a meaningful fine coal preparation overview is to be possible. COAL PREPARATION DEFINED In the opinion of the writer, the term "coal preparation" should be defined as including all work activities that are performed on all components of a run-of-mine coal from the time it leaves a surface reserve or an underground portal, until all components are either ready for shipment or are stowed on, or in the earth in an environmentally acceptable manner. This definition excludes the work that is performed to improve coal quality or handleability inside the mine or pit. This work is commonly called "face" or "pit" preparation. FINE COAL DEFINED The term "fine coal" means different things to different people. In the past, anthracite finer than No. 3 Buckwheat (3/16 in.) was considered fines which often were discarded from the breaker as an unsalable by product; and bituminous coals finer that about 1/4 in. (slack) were either discarded or sold at cost to prevent an accumulation of "no bills" which referred to a product having no immediate sale. Although a standard definition of "fine coal" is yet to be accepted by the industry, a designation of coals by particle-size range has evolved through the wide use of three-circuit flowsheets, wherein the optimum size range by washer type determines the size fractions: a coarse-coal circuit for the plus 3/8 in., a -11- coal circuit for the 3/8 in. x 28 Mesh, and a fine-coal circuit for the remaining 28 Mesh x 0. Logically, the term "fine coal" should refer to some resultant size fraction or some top size by zero. This definition should include a 28 Mesh x 0 feed to a flotation cell but should exclude a 28 x 100 Mesh size fraction fed to a heavy media cyclone. Failure to include the resultant sizes in the definition precludes accounting of the full range of particle sizes present in the feed to the plant. Since the 28 Mesh x 0 fraction is treated in the final circuit of the three discreet washing circuits, now almost always used in U.S. commercial applications, and since it contains all of its resultant sizes, in the writer's opinion, it should be designated "fine coal". FINE COAL CLEANING Cleaning coal fines, which in the past was at best marginally profitable, is now an essential part of coal preparation strategy for a number of reasons : 1. Raw coals now cost more to produce and

Jan 1, 1988

By C. E. Larson

Man's use of 'glass predates recorded history. Although early man had no knowledge of how to form glass, artifacts have been found near naturally occurring glass formations where molten rock had been rapidly cooled. In areas where volcanic activity is evident, primitive people fortunate enough to have lived in that area used the naturally formed glass to make arrow heads, knife blades, tools and ornaments. These glass artifacts have been found all over the world. In fact in todays modern society there are recorded cases of aboriginal tribesmen in Australia fabricating arrowheads from glass bottles. 2. A Brief History of Glass The first evidence of man made glass were beads made around 2500 BC by the Egyptians. The Mesopotamians also made glass beads at about the same time.

Jan 1, 1986

By C. Geier

Previous mine incidents show weaknesses in mine rescue preparedness from poor training in decision making, leadership and incident command center (ICC) protocols. Computer simulations offer a larger range of training opportunities for mine rescue teams focusing on exploration and communications. The mine rescue simulator developed by the Colorado School of Mines and Rite Solutions Inc. utilizes four computers for the instructor and team, with the instructor monitoring the team?s progress. As the team explores, it relays information back to the Fresh Air Base, which then reports to the ICC. This forces a three-step communication procedure, enhancing the team?s overall communication skills and developing ICC protocols. The simulator is decision-based, demanding team decisions be made quickly. Upon completion, teams commented positively. Generally, participants said that the simulator is useful for learning how to communicate and make decisions during mine rescue emergencies. This mine rescue simulator improves team training, providing effective communications practice with an easy setup and no production interruption.

Feb 1, 2014

By D. Sinha

Mine investment decisions involve both objective and subjective criteria. The subjective criteria are efficiently decided by interaction with company experts. The Expert System approach can incorporate knowledge of experts and interact with conventional computer programs on mine evaluation. Artificial intelligence offers considerable opportunities in comprehensive mine investment decision making process.

Jan 1, 1998

By E. G. Hoover

In the mid-I 970s the rallying cry sent out by the aggregate trade associations to aggregate operators was to come to Washington and help design national legislation mandating reclamation of pits and quarries. This collective effort paid off in that aggregate operators were able to assist in the design of "livable" legislation; however, the coal mining industry took some very hard hits. A principal argument used by the aggregate industry was that relatively small parcels of land are impacted, the operations are located in or near urban areas to serve in the development of that immediate area, and are of many years duration; whereas, coal strip mines disturb many acres, are of short duration, and whose products may have world or nationwide utilization. Historically, developments in reclamation are tied closely to the regulatory systems that have been created to control environmental effects of mining. Since reclamation generally results in a cost incurred after the stone, sand and gravel has been mined and does not add to the inherent value of the mineral, there was little incentive in the past for mine operators to reclaim the land. In 1977, the Surface Mining Control and Reclamation Act (SMCRA) became the law for coal mine operators. The law states that, among other provisions, reclamation must "restore the land affected to a condition capable of supporting the uses which it was capable of supporting prior to any mining, or higher or better uses". It is of interest to note that years before the initiation of legislation leading to SMCRA twenty-eight states already had reclamation regulations that covered virtually all minerals. The scope of performance standards found in the state reclamation regulations included slope stabilization, grading, revegetation, neutralization of toxic materials, visual screening, waste disposal, control of drainage, and other sources of pollution and erosion. Environmental legislation and the consequent regulations came about because the public perceived that private industry did not properly value environmental quality and as a result the government became the policeman.

Jan 1, 1998

By Francis F. Pitard

North America had an Important role in the early development of sampling theories. Unfortunately many progressive ideas were soon frozen into a series of guidelines based on the philosophy that "honest sampling only requires good judgment and practical experience". Such a philosophy appeared to be good enough In the early age of the mining Industry; however, it became quickly necessary to find new approaches. During the last thirty years, Pierre Gy's sampling theory provided tremendous breakthrough in the comprehension of this new science, nevertheless went unnoticed in North America. Sampling always generates complex problems and as the philosopher and mathematician Descartes suggested: "A complex problem can often be dissociated Into a series of several simpler problems, only then you try to solve those one by one". The only way to solve sampling problems is to consider each component of the overall sampling error: components of a continuous model such as long-range quality fluctuations, periodic quality fluctuations, weighting fluctuations; components of a discrete model such as materialization errors, delimitations errors, extraction errors, fundamental errors, grouping errors, and segregation errors. PAST AND CURRENT PRACTICES Many sampling methodologies have been developed, improved, and standardized during the first half of this century. Accordingly, sampling equipment has been proposed, selected, and used by standards committees. Today, there is a tremendous variety of sampling methodologies and corresponding tools offered to anyone with limited experience in sampling and it is very easy for a chemist, metallurgist, geologist or miner to spend considerable money in equipment transgressing the most basic rules of sampling correctness. Sampling stations that never worked properly in modern plants often cause engineers to abandon them and return to a primitive form of grab sampling.

Jan 1, 1986

By Robert W. Burns

Gentlemen, my subject today is glass reinforced plastics. By definition, this encompasses a wide variety of materials: at least a half dozen basic varieties of polyester, epoxy, and phenolic; virtually infinite compounding variations within the basic groups: literally limitless variations in the amount and the nature of the glass reinforcing. Complicating all of this is the fact that different modes of application of the same material fall appreciably alter' the product's general strength and suitability. These many, many differing materials are what we conveniently call "glass reinforced plastics" or, more simply, fiberglass". This common name is actually a large part of the problem when dealing with fiberglass materials. Far too often a specification is written calling for simply "fiberglass reinforced polyester', based on successful prior use of a polyester laminate. Such a specification is very nearly worthless since such tremendous variation is possible under it. Success of a laminate furnished under such a specification is entirely dependent on good fortune

Jan 1, 1962

By John Kuyt, Zili Li, Michael Mooney, Michele Mangione

"INTRODUCTIONTwin bored tunnels are commonly used for a variety of road and tunnel projects throughout the world. A major component of these twin tunnel projects is the construction of connecting cross passages that provide emergency access between tunnels and space for tunnel service equipment. Cross passages can present significant geotechnical risk and technical challenges to a project – support systems must be considered for redistributing loads around the mainline tunnel openings and supporting new loading resulting from excavation activities. Additionally, cross passages pose risks to construction schedule and cost because of their sequencing at the end of construction, so mitigation of schedule overruns can be critical. By observing field instrumentation data records from completed projects, a betterunderstanding of the force development in each temporary structure can be achieved with indication of which structures are the most critical to support ground loads.This paper discusses the data obtained during the Brisbane Airport Link construction project, a road tunnel located in Brisbane, Australia. Strain gauge instrumentation data from the precast segmental lining and propped opening steel sets is presented with relation to the construction sequence and local geology. Interpretations and conclusions based on the observed trends are proposed, with several key mechanisms affecting the loading and unloading identified.Brisbane Airport Link Project OverviewThe Brisbane Airport Link project in Brisbane, Australia, connects central Brisbane to the airport located northeast of the downtown with over 7km of twin-bore road tunnels, two lanes each, with several caverns, interchanges, and access ramps constructed along the alignment to connect to other key routes in the city. The project was executed under a Public-Private Partnership (P3) scheme, funded and operated by the consortium BrisConnections. The main contractors were a joint venture of John Holland and Theiss, while the design was carried out by Arup and Parsons Brinckerhoff.Construction of the tunnels was conducted using a combination of 17 roadheaders and two 12.5m double-shield Herrenknecht TBMs [1]. The TBMs were used in EPB-type closed mode for the initial portion of their drive, starting at the northeast end of the alignment. Tunneling started in soft ground, weathered rock, and mixed face conditions initially, progressing to competent sedimentary rocks as the drive continued. Support was accomplished using a 12.1 m diameter steel fiber reinforced concrete (SFRC) segmental lining installed behind the TBMs in a 9 segments + 1 key arrangement. The innovative design of these segments is detailed in the paper by Harding and Francis [2]. Ancillary roads and underground interchange caverns were constructed by sequential excavation techniques using roadheaders, accounting for nearly half of the total underground excavations."

Jan 1, 2016

By James R. Jones

The Surface Mining Control & Reclamation Act is a complex piece of legislation signed into law on August 3, 1977. It is the culmination of more than six years of debate by the Congress over the need for a national regulation of surface mining as opposed to the prior concept of regulation by each concerned state. It departs from the more normal type of law in that it includes very specific requirements, limitations and performance standards. In its procedural aspects, it is somewhat similar to the Clean Air Act and the Water Pollution Control Act in that it places primary responsibility at the state level, provided the state meets minimum national requirements. At the time of writing this paper, in late December 1978, the Interim Regulatory Program has been in effect for seven months. The proposed regulations for the Permanent Program, the draft Environmental Impact Statement, and the draft Regulatory (Economic) Analysis ware available for eight weeks before the close of the comment period on November 27. We are now awaiting issuance of the final versions of these documents. The states in which coal is mined, for the most part, have made sere revision to their state laws and are in the process of revising their regulations, or have just completed the revision, to comply with the Initial Regulatory Procedures. They are now faced with another new major effort to analyze and plan for compliance with the Permanent Regulatory Program, which is expected to be promulgated by the Office of Surface Mining of the Department of Interior by the time this paper is presented.

Jan 1, 1979

By H. K. Lin

The free-milling ore characteristics of the Fort Knox gold deposit are ideal for studying gold and silver behaviors in various processing circuits without serious interference of sulfide minerals and other refractory factors. A galvanic effect leads to faster silver dissolution than gold dissolution and, as a result, the Au/Ag solution concentration ratio increases through the leach circuit. In the CIP circuit, Au adsorption is more effective than Ag adsorption. The Au/Ag solution concentration ratio decreases from 10.0 to 1.0 as the slurry advances from CIP tank #1 to CIP tank #5, while Au/Ag ratio in the carbon increases from 3.2 to 15.3, as the carbon advances from CIP tank #5 to CIP tank #1. Silver is stripped more effectively than gold from the loaded carbon. The Au/Ag ratio in solution reaches 2.0 in the first 75,700 L of strip solution that pass through the loaded carbon; as the stripping process continues, the Au/Ag ratio in the strip solution increases. In the electrowinning circuit, the Au/Ag ratio in the spent electrowinning solution is significantly lower than that in the electrowinning feed, indicating that Au is more rapidly deposited onto the cathode than Ag.

Jan 1, 2010

By R. F. Korcak

There exists a wide array of industrial by-products that can be shown to produce beneficial responses in the soil/plant environment. These materials range from clean coal technology residues produced in the generation of electric power, particularly those high in gypsum, to mineral 'fines' produced by the aggregates and crushed stone industries. A number of these materials will be examined in relation to potential nutritional interactions in soils and crops with emphasis on trace elements. The significance of utilizing these materials in agriculture as a component of sustainable agricultural systems will be discussed.

Jan 1, 1995

By S. Bahrampour

One of the basic requirements for designing an optimized rock support for an underground opening is having reasonably enough geological information. It is often financially impractical to obtain detailed geological information about the rock surrounding the excavations. The geological and geotechnical information which are obtained during the construction phase are also usually inadequate and need periodic operation stoppage. Penn State University- J.H. Fletcher & Co. joint venture is to improve the existing instrumented roofbolter so that the 3D geological and geotechnical map of the rock mass surrounding the underground working can be generated real-time as the data is being collected. This information will also be used to design appropriate support for different sections of mines. In this paper, recent results in improving the performance of the measurement while drilling system will be discussed. Moreover, updates related to borehole probing methods for estimating the properties of the rock masses will be presented.

Feb 23, 2014

By M. Buxton

"Advanced data acquisition and process modelling technology provides online data and decision support about different aspects of the resource extraction process. Real-time approaches have recently been applied to utilize the value of this information for improved production control in mineral resource extraction in different operational set ups including coal, polymetallic ore and gold deposits. The key concept of these approaches promotes the change in paradigm from discontinuous intermittent process monitoring to a continuous process and quality management system in the resource extraction process. The framework includes a real-time feedback control loop that rapidly links online material characteristics data acquired during extraction at the mining face, during material handling and processing with a sequentially up-datable resource model. This will allow near real-time optimization of decisions related to long-term planning, short-term sequencing and production control. The contribution reviews recent developments in the three main constituents sensor based material characterisation, rapid updating of grade control models and simulation based optimization for improved production control. Technological readiness is assessed and critical gaps for further technology development are identified. The value added is illustrated by means of selected case studies. INTRODUCTION With the depletion of known and established mineral reserves, the decrease in head grades and the continuing demand of mineral raw materials by the modern society, future exploitation will move towards extraction of deposits under geologically more complex conditions. Complex deposits are characterized by a low continuity in grade, presence of deleterious elements such as arsenic and high irregularity in the geometry of the ore boundaries. The profitable exploitation of such deposits becomes significantly more challenging. To be able to better utilize such unconventional mineral resources of the future, smart autonomous mining systems are needed, which integrate local exploration of spatially varying material characteristics in–situ and have the ability to follow and extract the pay zones in the ore body while minimizing dilution (Buxton and Benndorf, 2013). The main barriers to overcome for the successful economic exploitation are: • effective grade control which will maximize resource potential along the whole value chain, • minimization of handling zero-value material introduced by dilution, thus • reducing unnecessary expenditure of energy and financial resources and • management and control of the geological uncertainty due to limited information available,"

Jan 1, 2017

By R. Snoby

Since its introduction in 2002, the modern air jig has processed a wide array of coals throughout the world. This paper explores the reasons and justifications for the installations and provides case history performance data. Specifically highlighted are air jig plants processing metallurgical coal in Colombia, bituminous coal in the United States and India and lignite in the United States and Spain. Each installation has unique reasons to justify an air jig facility. It is important to note that not all of the justifications were based on the ?most cost effective yield?, normally a mantra for coal preparation plant designers and owners. Dry jigging of coal has long been a proven technique for upgrading coal, the modern air jig, with its improved efficiency and operating systems simply extended the range of applications. In some cases, it even allows market quality coal to be produced when no other option is possible.

Jan 1, 2009

By Edgar F. Cruft

It is sometimes said that "mines are made, and not found". I rather doubt that the exploration geologist would be overly sympathetic to that statement, and, of course, like most one-liners it is only partly true. As an explorationist who has been involved in building his own company over the last ten years, and by necessity has become a financier, I can appreciate what real grains of truth are in that statement, however. Because technical people are seldom taught financing in their basic training, and because they are usually not involved in it until at quite a senior level in their careers, the whole field often acquires a certain mystique. The engineering professions have too often believed financing is the province of the accountant or financial executive and just as we in the technical world are often too quick to bristle if the latter try to tread on our domain, the opposite can just as easily be true. Unfortunately, this is another example of a compartmentalized individual, and that is one thing the successful financier cannot be.

Jan 1, 1979

By Cary Hirner, Sarah Lothman, Chris Mueller, Savita Schlesinger, Mike Hanna, Ian Fitz-James

Loudoun Water is currently implementing a quarry to reservoir conversion that will improve water supply reliability in periods of drought and flexibility in water supply operations when turbidity in its Potomac River supplies are high. The Milestone Reservoir Project consists of an inter-tie to the existing Potomac River Pipeline; new pipeline and tunnel; and a pumped intake and outlet works. Planned construction involves significant risks due to underground conditions which includes hard, igneous rock and high groundwater at the creek crossing. In addition, the site is constrained by Goose Creek, an adjacent residence, active mining in a quarry next to the new reservoir, public use of adjacent park space, and the Washington and Old Dominion Trail. Working with these constraints will require close coordination with active mining operations and public and private property owners. Safety of personnel involved with construction also represents a concern with quarry high walls over 30 meters in height near the planned construction. In consideration of key projects risks, Loudoun Water determined that an innovative CMAR delivery approach provided the best opportunity to achieve its goals in quality, innovation, front-end cost and schedule certainty, and operational flexibility and reliability. What matters most to Loudoun Water is the value in having a builder participate in the design process where key decisions can be made based on consideration of risks, cost, schedule, quality, and operability and maintainability of the system. While a progressive design-build delivery model may have produced similar outcomes, Loudoun Water had already invested in substantial development of the design for the work, and ultimately, CMAR provided Loudoun Water the opportunity to retain the partnership with the design team while gaining valuable input from a contractor. Among the challenges with CMAR in the Commonwealth of Virginia is a substantial limitation on self-performance corresponding to 10 percent of the construction value of the work. A significant industry outreach program was initiated by Loudoun Water to encourage participation with incentives in contract terms that allowed for the CMAR Contractor to make a reasonable profit. This paper reviews the CMAR procurement process and discusses contract incentives that were adopted to promote the work within the constraints of contract law in Virginia.

Jun 13, 2021

By Charles H. Wells

This paper presents a review of the state of the art in coal preparation plant instrumentation and a discussion of automation practice that could be applied based on current mineral beneficiation experience and demonstrated foreign technology in coal washing plants. Specific e-mules of applications of remotely controlled slurry values, pneumatic and electronic field transmitters, computers for control and data logging, and on-line analytical instrumentation are given. A program, to demonstrate this technology is described.

Jan 1, 1980

By Carmel Bofinger, Maureen E. Hassall, David Cliff, Eric Stemn

Incident investigation is of utmost importance in most high-risk industries and is often used to improve organisational safety. This study was undertaken to examine the content of past incident investigation reports to determine the effectiveness of the incident investigations. The study uses a semi-quantitative method to assess the effectiveness of incident investigations in the Ghanaian mining industry by evaluating the quality of past investigation reports. The assessment tool consists of five elements with several indicators and rating scales for assessing the quality of an investigation report as a measure of the effectiveness of the investigation. The method was applied to 304 investigation reports of three Ghanaian large-scale gold mines, and the results correlated with incidence rates of the mines to determine if any relationship existed. The results showed that the mines differ significantly in the quality of their investigation reports, suggesting differences in the effectiveness of their investigations. In addition, the incidence rates of the mines negatively correlated with some elements of the assessment tool. In general, the method was found useful and revealed areas where improvement is needed.

By R. G. Graber

Field testing of GPS mining applications has confirmed the technical and operational viability of GPS for precise, centimeter-level positioning in harsh taconite environments. GPS hardware has provided consistent availability exceeding 90%, with precision in certain applications of ± 0.07 foot at 95% confidence levels. Despite these technical successes though, challenges persist in achieving effective GPS integration. These challenges include the acceptance of new job tasks by mine personnel, the capacity of typical mine data communications infrastructure and the need to design GPS interfaces for new mining equipment.

Jan 1, 1998