Search Documents

By J. Twining, V. Nguyen, J. Perera

A computer code for ecological risk assessment (ERA), AQUARISK, has been developed and applied to evaluate the likelihood of biotic detriment due to exposure to acid rock drainage (ARD) from the Burkunga mine site in Australia Stream water quality monitoring data were used for the assessment and were compared with a) national water quality guidelines, b) literature derived ecotoxicology data and c) biological monitoring data. With bioavailability calculations, the code predicted that, for metals exceeding the guidelines, 44% of macroinvertebrate species above the mine and 100% below the mine would be adversely affected by the metals in the stream. This compares reasonably and conservatively with biological monitoring that showed observed reductions of 41% and 85% of species respectively at each site. Using literature data for macroinvertebrates to predict impact produced similar estimates to using data for all taxa. Use of speciation modeling also lessened the degree of reduction in the median water metal concentrations required to achieve acceptable impact (measured either by exceedence of criteria or by species likely to be affected) by a factor of 75%. This result implies significant economic and management benefits in relation to remedial engineering or water treatment options for sites.

Jan 1, 2000

By A. M. Raichur

The selective adhesion of hydrophobic Mycobacterium phlei to coal particles is responsible for flocculation of fine coal from associated ash forming minerals. The driving force for the differential adhesion is the hydrophobic interactions between the fatty acid surface of the organism and hydrophobic nature of coal. The effect of Mycobacterium phlei on surface hydrophobicity, surface charge and mechanism of adhesion on coal and associated minerals are controlled by several factors including hydrophobicity and surface and solution chemistry of the system. Adhesion measurements indicate that maximum adhesion occurs below the isoelectric point (IEP) of the coal particles. While massive adhesion of Mycobacterium phlei is observed on coal, however, negligible amount of Mycobacterium phlei attaches to mineral pyrite and quartz.

Jan 1, 1995

By Vasiliki Founta, Andrew J. Whittle

"This paper describes the development of a 3D finite element model for predicting ground movements caused by construction of 7.1 m diameter twin bored tunnels for the Crossrail project in London using Earth Pressure Balance (EPB) machines. The model uses the commercial FE code, Plaxis 3D, to represent the face pressure, conical shield, grouting process and activation of precast segmental concrete lining systems through a set of boundary conditions that advance through the soil mass along a prescribed trajectory. Soil behavior is described using the Mohr-Coulomb soil model with input parameters calibrated from laboratory element tests. The analyses focus on the performance of the EPB tunneling machines in greenfield conditions beneath Hyde Park, where the tunneling occurs within deep layers of relatively uniform London Clay. The model predictions are in good agreement with surface and sub-surface vertical settlements measured at a well-instrumented section, but tend to overestimate the measured lateral displacements towards the tunnel. Ongoing studies are focused on the role of soil behavior and the approximations in FE model predictions of tunnel-induced ground deformations. Introduction Since their introduction in the 1970’s, closed-face Earth Pressure Balance (EPB) machines have become widely used for soft ground tunnel construction. The EPB design relies on a screw conveyor system to regulate the pressure of the excavated soil/spoil within the head chamber and hence control stability at the face of the machine. One of the key design issues in the application of EPB machines is to establish how control parameters, including the advance rate, face pressure and grouting processes (used to compensate for the tail void at the rear of the shield and to infill gaps between the precast lining rings and surrounding soil) affect and/or control the far-field ground movements. For closed-face systems, short-term deformations are associated with ground losses at the face, overcutting and ploughing of the shield and poor control of grouting in the tail void; while long-term deformations can occur due to consolidation and creep within the surrounding soil (and are closely connected to the seepage boundary conditions;e.g., Laver & Soga, 2012). The control parameters for advancing the EPB machine can have a significant effect on the magnitude and distribution of the far-field deformations. Therefore, analyses of the ground response to tunneling require accurate modeling of the soil stratigraphy and constitutive behavior as well as the construction process. Finite element (FE) methods have been used to simulate tunnel construction since the early 1980s, but only a few studies involved three-dimensional modelling of mechanized tunneling (e.g., Finno and Clough 1985; Bernat and Cambou 1999; Swoboda and Abu-Krisha 1999; Dias et.al. 2000; Melis et.al. 2002; Kasper and Meschke 2004; Möller 2006). In order to get a better understanding of the effect of the construction process and soil properties on the development of the ground deformations more comprehensive models of tunnel excavation and tunnel support are required in order to capture the 3D nature of mechanized tunneling and the effect of construction parameters such as advance rate, face and grout pressure."

Jan 1, 2016

By J. P. Rider, T. W. Beck, J. A. Organiscak

"The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Mining Research Division (PMRD) has recently developed a series of models utilizing computational fluid dynamics (CFD) to study gas distribution around a continuous mining machine (CM) with various fan-powered flooded bed scrubber discharge configurations in an exhaust curtain working face. CFD models utilizing species transport model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The study illustrates the gas distribution in the slab (second) cut. The following scenarios are considered in this study: 100% of the discharge redirected back towards the face on the off-curtain side of the continuous miner; 100% of the discharge redirected back towards the face, but divided equally to both sides of the machine; and 15% of the discharge redirected toward the face on the off-curtain side of the machine, with 85% directed into the return. These models were compared to a model with a conventional scrubber discharge where air is directed away from the face into the return. The models were validated based on experimental data and accurately predicted sulfur hexafluoride (SF6) gas levels at four gas monitoring locations. One additional prediction model was simulated to consider a different scrubber discharge angle for the 100% redirected, equally divided case. This paper describes the validation of the models based on experimental data and the gas distribution results of the CFD models. INTRODUCTION To control methane gas and dust concentrations on continuous mining operations, it is important to provide sufficient quantity of fresh air from the end of tubing or curtain to the active face. In this region, operating machine-mounted water sprays and fan-powered, flooded bed scrubbers can significantly increase the amount of airflow reaching the face [1-3]. However, when an entry is large, especially in higher coal seams, the water spray configuration and the scrubber capacity may not be adequate to maintain sufficient forward airflow to confine the dust cloud to the face. Dust can roll back toward the machine operator as a result [4]. Currently, several coal mines having negligible gas emissions in higher coal seams (2.4 to 3.0 m [8 to 10ft.] thick) with exhaust tubing systems redirect the scrubber discharge back towards the face in an effort to improve dust collection. NIOSH studied the redirected scrubber exhaust techniques for dust and gas control in a full scale CM gallery to assess its potential for industry-wide application [5]. For a CM face, previous studies have concluded that the behavior of gas and respirable dust is a complex process. The distribution/dispersion and transport of gas and respirable dust after they are liberated at the face are governed mainly by their mass properties, the movement pattern of the ventilation air, and interactions with the mining machine and water droplets created by the external water spray systems used for dust control [6-10]. To understand these behaviors in a complex CM environment and to evaluate the effectiveness of various control techniques, numerical modeling has become a necessary supplement to laboratory experiments and field studies."

Jan 1, 2017

By Valeh Aghazadeh, Shima Barakan, Mina Soleymani, Ehsan Bidari, Morovvat Faridazad

Molybdenite is the most important molybdenum concentrate, which is mainly recovered as a by-product from porphyry copper deposits. Due to the low efficiency of purification processes such as flotation in the reduction of copper content of molybdenum concentrate to a standard level (i.e., less than 0.5 wt.%), further purification by a hydrometallurgical method is required. Although different types of chemical reagents were found to be effective in the leaching of copper minerals from molybdenum concentrate, the mechanisms of these processes remain largely unexplored. In this study, optimal conditions for maximum copper leaching (> 99%) were obtained at the concentration of HCl = 1 M, FeCl3 = 0.5 M, CuCl2 = 0.05 M, CaCl2 = 0.5 M at 75 °C, 500 rpm, and S:L = 1:10 during 60 min. CuCl2 was identified as the most effective leaching reagent for copper dissolution in agreement with Visual MINTEQ model results due to the formation of various types of copper chloride complexes. Furthermore, the electrochemical behaviors of FeCl3, CuCl2, and CaCl2 reagents before and after the leaching process were investigated by the cyclic voltammetry technique. The results of cyclic voltammograms at different scan rates verified the presence of copper chloride complexes, and ferric ions as the oxidizing reagents for better dissolution of copper sulfides. Based on kinetic study results of shrinking core models, both chemical and diffusion reactions controlled the copper leaching process with an obtained activation energy of 33.56 kJ/mol. For recovery of the leached copper, the precipitation process was done by the addition of Na2S at 45 °C, S/Cu = 1, and pH = 9.

Dec 26, 2022

By Mark P. Walsh

In recent years in situ leach mining has emerged as a viable technology for the recovery of uranium from strata in South Texas which contain relatively low concentrations of uranium ore. Because the ore bodies lie within groundwater aquifers, a significant determinant in the economics is the requirement that such aquifers be protected from contaminantion. Since ammonia is one of the constituents of the leach solutions now being field tested, one environ- mental problem to be resolved is the removal of ammonia at the end of mining. A second related question is the fate of the ammonia which is not removed by the restoration procedure. This paper considers the displacement and migration of ammonium in a flowing electrolyte with concomitant ion exchange. The ion exchange is an important feature since, during the solution mining phase, ammonium saturates the mineral exchange sites and must be removed from these sites. A mathematical model is used to simulate this process and the model is tested against the results of laboratory experiments. It is found that the simulations are adequate if an appropriate selection of parameters is made. The model is then used to investigate the effect of cation composition and concentration of the restoration medium as well as dispersion on the overall effectiveness of the process. It is concluded that increasing the concentration of monovalent ions in a solution containing a mixture of both monovalent and divalent ions decreases the adsorption selectivity of the divalent ions with respect to all monovalent ions including ammonium. Thus increasing the ionic concentration of a restoration fluid by increasing the concentration of a nonselectively adsorbed (with respect to ammonium) ion may have a very limited benefit. Dispersion attending the flow of fluids in a porous medium is also shown to be an important factor. The effect of dispersion can greatly reduce the benefits of having a displacing cation which is adsorbed selectively with respect to ammonium. Since dispersion increases almost linearly with fluid velocity, an optimum displacement rate may exist.

Jan 1, 1979

By S. Mason

Many organizations are realizing that continual improvement in health and safety relies on addressing the potential for various forms of human error. Of these, violations are often the most frequent form associated with accidents. These occur when an individual, or individuals, deliberately contravenes established and known safety rules. They have been associated with up to 90% of accidents and incidents in some industries and yet rarely receive the systematic attention they deserve in the promotion of safety. This paper presents underlying motives which cause violations. These can vary significantly from mine to mine and from job to job. Managers need some measure of attitudes to determine the underlying motives behind violations if they are to determine effective strategies for promoting safe behaviour. Questionnaires form the starting point to address attitudes and the motives behind rule violations. The choice of the most suitable questionnaire, however, will vary from organization to organization. Guidelines on the choice of questionnaire are offered.

Jan 1, 1998

By Anand Kumar, Debasis Deb, V. N. S. Prasad. M, A. K. Mishra

Shield leg pressure data from all shields and shearer locationwith time stamp from a mechanized longwall face are monitored and recorded in a surface computer. These data contain random noise due to power failure, leakage of legs, bad sensor reading and other maintenance or geo-mechanical problems. An algorithm is developed to detect mining cycle parameters such as setting and final pressures and duration of the cycle from these data for the analysis of periodic roof weighting phenomena. The intensities and persistence of periodic roof weighting are the vital information to the mine management to take judicious decision on longwall operation. The paper presents details of the algorithm which identifies 96% of mining cycles from the noisy data belonging to consecutive 5 months or 410 m of face advancement. Based on this analysis, 2 types of periodic roof weighting phenomena are detected, namely, (i) normal type—having peak intensity of 75 to 90% of yield pressure, interval of occurrences of about 10 to 15 m with persistence of 3 to 4 m and (ii) severe type—peak intensity over 90% of yield pressure, interval of 25 to 40 m with persistence of over 10 m. It is envisaged that these phenomena have direct relationship with main roof thickness, its overhung length and material properties.

Nov 19, 2020

By MUSTAFA ERKAYAOGLU, ENVER YILMAZ

Coal is still a part of energy generation worldwide and has a significant role in the sustainable development of countries. The amount of shallow coal deposits is getting scarce, making efficient underground mining operations crucial for both local and global economies. In underground mining operations, longwall mining is a commonly utilized method to extract deep coal deposits. One of the leading engineering goals in longwall mining is increasing the efficiency of the system by investigating the effects of operational factors on equipment. This paper investigates the shearer performance for a longwall top coal caving operation by discrete event simulation that includes modeling the double-drum shearer, belt conveyors, stage loader, and armored face conveyors (AFC) to evaluate system performance by considering the amount of daily coal production of the shearer. As a result, the most influential factor on mine production is determined and a data-based framework is developed. This study suggests a framework for data collection, data analysis, and the interpretation of the operational data to evaluate the primary production unit’s performance. The models developed for the face coal extraction operations in a longwall top coal caving (LTCC) mine have a bi-directional cutting system and can be implemented in other operations readily.

Jul 2, 2021

By Amoussou Coffi Adoko, Shevaune Zeng, Sebastian D’Hyon, Gareth Kennedy, Eleonora Widzyk-Capehart

Inertization of coal dust with stone dust is a common control implemented within underground coal mines to mitigate the hazard of a coal dust explosion. To achieve adequate inertization, the total incombustible content (TIC) of the coal/stone dust mixture is required to meet certain percentages depending on the risk and relevant legislation. Current methods for determining the TIC of a mixture involves laboratory analysis, colorimetric comparison, or the use of portable instruments. This paper provides preliminary analysis of determination of a sample’s TIC in real-time with chemometric modelling, using portable instruments employing near-infrared (NIR).

Feb 1, 2024

By John W. Leonard

The typical tunnel boring machine in use on today's tunnel project uses 15'2-inch diameter cutters at a nominal load of 45 kips per cutter. The cutterhead rotates at a speed of 120 over D revolutions per minute where D is the cutterhead diameter in feet. The typical machine operates about 50 percent of the time. Delivery of a new machine takes 12 to 15 months. The TBM is a specialized tool and not applicable to all jobs. There is a range of job conditions that limit the economic use of a TBM. The machine should provide a thrust per cutter at least twice the compressive strength of rock in psi and up to three times the rock strength is required if in "granitic rocks." The rock strength in psi must be at least three times the cover above the tunnel in feet or the machine may stick. For example, 2,500 feet of cover requires at least 7,500 psi rock to avoid problems. When the RQD's over a significant distance of the project are less than 50, the TBM becomes support-bound. When a large percentage of the time is spent waiting while the ground is supported, the TBM cannot perform well (See Figure 1). This problem increased inversely with tunnel diameter. We are finding that increasing the RPM's does not significantly increase progress. The increased RPM results in a substantial decrease in cutter penetration. The explanation for this decrease appears to be vibration, cutterhead drag, or lack of stiffness in the cutterhead (See Figure 2).

Jan 1, 1981

By Joseph M. Hans

INTRODUCTION The decontamination of a uranium mill site is principally an earth moving task. The task can be completed effectively and efficiently by selecting the proper earth moving equipment and using that equipment within its particular constraints for decontamination work. A considerable backlog of experience concerning earth moving equipment selection and use was acquired during the decontamination work conducted at the former Shiprock, New Mexico, uranium mill site. This experience was acquired by trial and error while decontaminating over a wide range of depths and different types of terrain. Many different types of excavation equipment were available to the Shiprock decontamination project because the Navajo Engineering and Construction Authority (NECA) heavy equipment operator's school was doing the decontamination work and a variety of equipment was needed for training. The equipment is described and its general use for decontamination is discussed. Its on-the-job use for decontaminating the Shiprock millsite is presented. [EARTH MOVING/ANCILLARY EQUIPMENT DESCRIPTION AND DECONTAMINATION CONSTRAINTS] Tractor-Scrapers The most commonly used scraper is the bottom-dump type because it is highly mobile and can dig, carry, and spread loads. In this type a tractor is connected with a yoke to a scraper bowl (Figure 1). The bowl is essentially a rigid box that pivots around the rear axle, opening to the front. A hardened steel knife, or bit, is attached to the leading edge of the bowl. When scraping, the bit penetrates and forces the earth overlying the bit edge into the scraper bowl as the scraper moves forward. When the bowl is full, it is closed by lowering a closure or apron against the cutting bit. The load is dumped while moving, by raising the apron and forcing the load from the bowl with a crowd, or ejector. The height of the dumped load is controlled by adjusting the bit height when dumping. Scrapers of this type generally do not have enough power to scrape up loads unassisted. Loading assistance is generally provided by a crawler tractor that pushes from the rear against the scraper's push block. Some scrapers are made self-loading by adding an additional engine for the extra power needed for the load pick up. Another commonly used self-loading scraper uses a loading elevator (Figure 2). The elevator consists of two roller chains carrying crossbars. The elevator is rotated when scraping and the crossbars cut the earth above or in front of the bowl bit, forcing the load into the scraper bowl. No apron is used on elevating scrapers. The load is dumped by partially retracting the bowl floor and pushing with an ejector. Scrapers have some undesirable characteristics when used for decontamination work. One characteristic is that a clearance space exists around the apron when it is in its closed position. Part of the load (especially sandy soils) dribbles through the

Jan 1, 1981

By B. Moore, Y. J. Zhang

In today’s competitive dimensional stone business environment, use of available technology is critical to achieve and maintain a competitive advantage. Awareness of improvements in diamond cutting technology, operation planning/scheduling, and geotechnical data manipulation/implementation are the keys to success. This paper presents the modern techniques of limestone sawing and quarrying developed and adopted by Indiana Limestone Company, Inc.(ILCI).To fulfill the growing market demands, ILCI’s quarries are committed to deliver planned quantities of all type of stone blocks in a variety of different colors, sizes, and textures. This involves scheduling which quarry ledges should be mined and when in order to minimize unnecessary inventory buildup. Challenges associated with ILCI’s operation are discussed and summarized in the closing of this paper.

Jan 1, 2004

By J. R. Patts, A. B. Cecala, E. J. Haas

Exposure to respirable crystalline silica (RCS) remains a serious health hazard to the US mining workforce who are potentially exposed as various ore bodies are drilled, blasted, hauled by truck, crushed, screened, and transported to their destinations. The current Mine Safety and Health Administration (MSHA) permissible exposure limit (PEL) for RCS remains at approximately 100 μg/m3 , but it is noteworthy that the Occupational Safety and Health Administration (OSHA) has lowered its PEL to 50 μg/ m3 (with enforcement dates staggered through 2022 for various sectors), and the National Institute for Occupational Safety and Health (NIOSH) has held a 50 μg/m3 recommended standard since 1976. To examine a method for reducing RCS exposure using a NIOSH-developed video exposure monitoring (VEM) technology (referred to as Helmet-CAM), video and respirable dust concentration data were collected on eighty miners across seven unique mining sites. The data was then collated and partitioned using a thresholding scheme to determine exposures that were in excess of ten times the mean exposure for that worker. Focusing on these short duration, high magnitude exposures can provide insight to implement controls and interventions that can dramatically lower the employee’s overall average exposure. In 19 of the 80 cases analyzed, it was found that exposure could be significantly lowered by 20% or more by reducing exposures that occur during just 10 min of work per 8-hour shift. This approach provides a method to quickly analyze and determine which activities are creating the greatest health concerns. In most cases, once identified, focused control technologies or behavioral modifications can be applied to those tasks.

By K. H. McDaniel

Eight Mine Weather Stations (MWS) installed at the Waste Isolation Pilot Plant (WIPP) to monitor the underground ventilation system me helping to simulate real-time ventilation scenarios. Seasonal weather extremes can result in variations of Natural Ventilation Pressure (NVP) which can significantly affect the ventilation system. The eight MWS(s) (which previously collected and stored temperature, barometric pressure and relative humidity data for subsequent NVP calculations) were upgraded to provide continuous real-time data to the site wide Central Monitoring System. This data can now be utilized by the ventilation engineer to create real-time ventilation simulations and trends which assist in the prediction and mitigation of NVP and psychrometric related events.

Jan 1, 1997

By William A. Faust

At Gold Fields' Chimney Creek Mine, major reviews of the reclamation and closure plans are done concurrently with the annual mine planning required for budget preparation. This review includes identifying and scheduling reclamation work that can be done within the next few years and development of associated costs. Longer term mine, leach pad and waste dump development are examined to take advantage of any design changes that can reduce ongoing reclamation or closure requirements and reduce costs. The success and cost effectiveness of past efforts are continually evaluated to determine the best methods for reclamation.

Jan 1, 1992

"INTRODUCTION Twin Metals Minnesota (TMM) (operating as a joint venture between Duluth Metals and Antofagasta PLC) assumed control of the property in 2010. Amec became involved with the project in 2011 and in 2012 incorporated additional drilling in order to update historic resource estimates. The Maturi geological model and resource estimate was updated in 2014 to incorporate additional information obtained during 2013 and 2014 drill campaigns. In 2017, Amec was purchased by the Wood Group and is now known as Wood. Geology The Twin Metals Minnesota (TMM) Maturi, Maturi Southwest, Birch Lake, and Spruce Road properties are located in northeastern Minnesota (Figure 1). This talk discussed the Maturi deposit only, although all four deposits share similarities. The following geology is summarized from Peterson and Severson (2002).Maturi lies within the Superior Province of the Canadian Shield which is exposed in central and northeastern Minnesota and extends northward into Ontario. In eastern Minnesota, the Midcontinent Rift System developed during crustal scale extension in the Mesoproterozoic Era. The rift system is traceable, as exposures of mantle-derived tholeiitic to subalkaline mafic lava flows, intrusives, and rift-filling fluvial sedimentary rocks, and in the subsurface as a gravity anomaly (high), from the eastern end of Lake Superior, arcing west across the lake basin, and extending south-southwest to northeastern Kansas. Intrusion of the Duluth Complex, circa 1,108 - 1,099 Ma, was related to rifting and is co-genetic with the North Shore Volcanic Group mafic volcanic rocks that form the hanging wall of the Duluth Complex to the east. Cu-Ni-precious metals (PM) mineralization including Pt, Pd, Au and Ag within the Duluth Complex is hosted by mafic to ultramafic intrusive rocks that are part of the overall intrusive complex. The Duluth Complex is defined as a more or less continuous mass of mafic to felsic plutonic rocks that extends northeastward for more than 170 miles (275 km) in an arcuate fashion from Duluth nearly to Grand Portage in Minnesota. It is bounded by a footwall of Paleoproterozoic sedimentary rocks and Archean granite-greenstone terranes (Peterson and Severson, 2002), and a hanging wall largely of comagmatic anorthosite, rift related flood basalts, and hypabyssal intrusions of the Beaver Bay Complex. Mineralization is hosted in the basal mineralized zone (BMZ) of the South Kawishiwi Intrusion (SKI). The SKI magmas intruded sub-horizontally between hangingwall Anorthositic Series (AN) rocks and footwall granitic rocks of the Neoarchean Giants Range batholith (GRB). The Maturi local geology and the deposit footprint (shaded orange) is shown in Figure 2."

Jan 1, 2018

By T. J. Morris

"From November 2014 through September 2016, Westmoreland’s Coal Valley Mine utilized a Marion 7450 electric walking dragline to extract 1.2 million tonnes of a vertically-dipping, 52-meter wide, fault-thickened seam, beneath a conventionally-excavated pit bottom. Mine planning and operational hurdles encountered throughout a kilometer of mined strike length included mitigating highwall instability in both hanging and footwall slopes, water management, and end-of-life machine reliability and maintenance. The most substantial challenge has been the depressed global coal market. However, the successful application of this mining method significantly aided the overall cost of production at the site. The valuable experience gained from this project will be extended to future mining areas where this technique can be similarly applied. INTRODUCTION Coal Valley Mine is located approximately 220 kilometers southwest of Edmonton, Alberta, Canada, in the foothills of the Rocky Mountains. Since commercial production began in 1978, more than 84 million clean tonnes of coal has been produced and sold domestically as well as exported overseas for power generation. While the existing processing plant has a nameplate capacity of 4 million tonnes per year, the site has operated at a 2 million tonne rate since 2015 due to depressed export markets. Westmoreland acquired the mine as part of its purchase of Sherritt Coal Operations in April 2014. The mine operates 24 hours a day, 7 days a week, with an IUOE workforce of 261. GEOLOGICAL SETTING The geology of the Yellowhead Tower mining area differs significantly from previous mining areas at Coal Valley. The Mynheer coal seam discussed herein consists of steeply dipping, highly-sheared, thrust-faulted, and heterogeneous coal pods. Deep set, southwest striking thrust faults were the likely mechanism for the podding and have resulted in overturned, rolled and highly sheared seams with zone thicknesses of up to 65 meters.The hanging wall is characterized by soft bentonitic mudstones and siltstones, overlain by massive competent sandstone. The footwall is defined by a hard volcanic tuff, interbedded with thin, sporadic coal seams. The sandstone above and volcanic tuff below constrained the faulting system within this zone, enabling the mass podding that has afforded the opportunity for large-scale mining."

Jan 1, 2017

By T. J. DeMull

The business of heap leaching requires accurate forecasting of metal production from the heaps. Business forecasts typically follow a format that project periodic (monthly, quarterly, or annual) product shipments based on anticipated operating results, e. g., tons of ore placed, grade of ore, and rate of leach extraction. Since revenue and cash flow are dependent on the metal production stream, forecasts of metal production are very important for project evaluation and business planning purposes. Nevertheless, production forecasts, particularly for new heap leach projects, have been prone to errors. The present paper identifies some of the pitfalls that would be encountered in preparing production forecasts for new heap leach operations and provides a checklist of considerations to assist in preparing a forecast. Also, the paper presents a case study of copper production forecasting used for the Sanchez Project, a heap leach operation located near Safford, Arizona, that is presently under development by AZCO Mining, Inc.

Jan 1, 1995

By Donald L. Everhart

The National Uranium Resource Evaluation (NURE) program since 1974 has been designed to accomplish a comprehensive coverage of the 48 conterminous States and Alaska to evaluate the total uranium resources of the USA. This resource base includes both ore reserves and potential resources. Techniques include airborne radiometric and magnetic surveys, by hydrogeochemical surveys, surface and subsurface geologic studies, and the application of improved geochemical exploration and resource assessment methods (Table 1). In brief review, the current status of each of the five basic NURE elements is as follows: In the Aerial Surveys, in the conterminous 48 states, the flying has been completed in 89 of the NTMS 10 x 2° NURE quadrangles, and is in progress in 39 more (Figure 1). Complete quadrangle data have already been open filed for 46 additional quadrangles, for a total of 174 for which data gathering is either complete or in progress. In Alaska, the flying is complete in 42 quadrangles, and quadrangle data have been open filed for 34 more, for a total of 76 (Figure 2).

Jan 1, 1979