Search Documents

By Y. B. He

The effect of the stability and rheological properties of magnetite dense medium on the separation performance of a 6" dense medium cyclone (DMC) is studied with the use of fine density tracers. The tests in which different size fractions of magnetite are used to prepare the dense media reveal that at low medium densities (<1.5 s.g.), the best separation is achieved when using the magnetite with intermediate particle sizes (du3.2=18 11m). At medium densities above 1.5 s.g., however, it is beneficial to use coarser magnetite. With the fine magnetite dense medium, an increase in medium density results in a decrease in separation efficiency. With the coarse magnetite, an opposite trend is observed; the separation efficiency is improved with increasing medium density. An accurate cutpoint control is critical in gravity separation. The cutpoint shift for coarse feed particles is found to decrease with increasing medium stability (density). It assumes values close to zero in a highly stable fine dense medium. When the size of the treated particles is small (<0.5 mm), the cutpoint shift is mainly determined by medium rheology. With increasing medium density, a continuous increase in cutpoint shift is observed.

Jan 1, 1993

By Byron C. Hardinge, E. R. Palowitch, Albert W. Deurbrouck, David J. Akers, Edward R. Torak

During 1983, 42.2% of the 686.0 (624.3 Mt) million tons of coal reported, 289.6 (263.5 Mt) million tons were mechanically cleaned, of which 107 (97.4 Mt) million tons were cleaned by dense media (magnetite and sand) processes.&apos; The percentage of bituminous coal and lignite cleaned mechanically by dense medium processes increased from 7 to 38% between 1938 and 1983. The Electric Power Research Institute estimates that 150 million tons (137 Mt) of coal were cleaned by heavy-media processes in 1986, and that this number may increase to 265 million tons (241 Mt) by 1990.2 Dense medium separations include those coal preparation processes that clean raw coal by immersing it in a fluid having a density intermediate between clean coal and reject. As there is a general correlation between ash content and specific gravity, it is possible to achieve the required degree of removal of ash-forming impurities from a raw coal by regulating the specific gravity of the separating fluid. Dense medium processes generally offer the following advantages over other coal cleaning processes: • Ability to make sharp separations at any specific gravity within the range normally required even in the presence of high percentages of raw coal whose specific gravity is near the specific gravity of separation. • Ability to maintain a separating gravity that can be controlled within + 0.005 sp gr units. • Ability to handle a wide range of coal sizes. • Ability to change specific gravity of separation to meet varying market requirements. • Ability to handle fluctuations in feed, in terms of both quantity and quality. Unfortunately, dense medium processes can have the following disadvantages: • Relatively high capital costs caused primarily by the need for equipment to collect and recycle the medium. Relatively high operating costs caused primarily by operation of medium recycle equipment and loss of medium.

Jan 1, 1991

By Charles B. Dugger

Sacrificial linings for grinding mills have been a necessary state of the art of mineral dressing since the inception of comminution. Long recognized as the final link in energy transmission from power line to ore, mill liners as a scientific endeavor have not expanded as rapidly as other branches of mineral dressing engineering. Several reasons for this technological lag are apparent. Typically in the past, labor intensive foundries were freely located geographically, at a time when transportation charges made up a significant portion of the casting cost. Alloying agents had not gained their current level of sophistication and were relatively inexpensive in the quantities required. Precise foundry controls were not economically justified, or totally understood. Coincidental to these elements, liner consumption per unit processed did not categorically contribute as a major cost item to the mill operator. Grinding equipment was small, and many times lining life exceeded that of the promoter. These unique conditions no longer exist. Ore dressing equipment has grown to meet modern mining demands. Larger processing facilities, utilizing fewer pieces of equipment, have replaced operations of the past. Emphasis today and tomorrow is on larger and larger equipment, with an eye on lower and lower unit processing costs.

Jan 1, 1979

By S. C. Brown

A number of studies have suggested that microscale asperities enhance bubble-particle attachment efficiency; however, in practice the roughening of particulate surfaces can also lead to a decrease in flotation. In the present investigation, it is proposed that nanoscale asperities may be partially responsible for this phenomenon. It is suggested that as inter-asperity separation distances are reduced capillary effects are enhanced leading to the formation of stable liquid domains, which adversely impact bubble-particle adhesion. In addition, obstruction of surfactant self-assembly may occur, further limiting flotation.

Jan 1, 2003

By Leland L. Mink

Open-pit mining is sometimes conducted in areas where the artesian pressures contained in aquifers underlying the pit&apos;s floor are great enough to cause floor heave. In order to reduce this pressure several methods are commonly used. One of these methods is a pressure relief well or depressurization wick. The wick consists of a borehole which is filled with gravel and cased at the surface. The wick is allowed to flow freely, thus reducing pressure near its location. The spacing and depth of these wicks can be determined by a simple analytical and graphical technique which considers the weight of material overlying the aquifer and the artesian force within the aquifer. An example of the technique using data from a Colombian coal mine is presented.

Jan 1, 1986

By Hasan Nizamoğlu, Z. Abidin Sarı, Aslıhan Demiraslan, M. Deniz Turan, Tolga Depci

In this study, recovery of copper from solid material (obtained by leaching of chalcopyrite with oxalic acid in the presence of hydrogen peroxide) with a copper oxalate structure was carried out selectively using HCl. The chemical composition of the solid was as 29.3%, 9.7%, and 13.3% for Cu, Fe, and S, respectively. Selective recovery of copper by degrading the copper oxalate structure with a low-solubility product (Ksp = 4.43 × 10−10) was performed by conventional leaching in the presence of HCl. The optimum leaching conditions were determined as 5 M of HCl concentration, 318 K of leaching temperature, 120 min of leaching time, 25 ml/g of liquid–solid ratio and 400 rpm of stirring speed. Under these conditions, approximately 77% of copper and 3% of iron were taken into the solution. According to the characterization of the leach residue that was obtained, the oxalate structure was degraded. Moreover, the results of XRD analysis showed that the sulfur (S) and cubanite (CuFe2S3) phases were mostly observed in leaching residues, and this was supported by the SEM-EDX data. Based on the results, it may be stated that selective copper extraction can be obtained from a chalcopyrite concentrate by a two-step leaching method using a conventional hydrometallurgical technique.

By Samer Sadek

The Georgia Department of Transportation (GDOT) undertook an exploratory feasibility study to one of the most ambitious tunneling projects in the United States. HNTB Corporation was retained to perform the study, deemed the Atlanta North-South Tunnel, which is approximately 7 miles long and consisting of four lanes (or six lanes) starting at the southern terminus of SR 400 extending to the south connecting with the northern terminus of I-675, providing substantial relief to the Downtown Connector (I-75/I-85), the most congested portion of Atlanta?s freeway system. This paper summarizes the analysis performed during the first phase of this challenging assignment which, if constructed, would be one of the longest roadway tunnels ever built in the United States.

By Robert Turner

Gold and silver processing techniques are some of the oldest in the mining industry. Gold mining of high grade veins and deposits has existed for centuries. However, only with the higher gold prices in recent years and heap leaching techniques have the low grade gold and silver deposits become feasible to mine and process economically. By mining and hauling 3,600,000 tons of ore per year at an average grade of 0.03 ounces/ton gold and 0.385 ounces/ton silver, the Zortman- Landusky operations became profitable in 1982. To maintain profitably, a stripping ratio of less than one ton of waste to one ton of ore, and mine run ore placed on the leach pads which will yield approximately seventy percent go1 d recovery.

Jan 1, 1984

By Frank Matter

The production of ultrafine slurries and powders is possible with small media made out of Si02, A1203, Fe203, Zr03 or other raw materials due to the fact that since approximately 12 years from now, entirely new machines have been developed which allow to use this small media for the production of ultrafine pigments. Basically we distinguish between two grinding methods which are: A.) Dry Grinding with Air Classification: This method is used for more than fifty years but only since four years this technology is realized with small grinding media. Many problems like cooling, abrasion, control of the media flow, separation media from product, grinding media recycling etc. had to be resolved before it was possible to get in full production with this new system. Hereafter a flow-sheet of such a TRZK mill with an air classifier especially designed to produce end products with a top size between 2,5 and 3,0 micron and with an average particle size between 0,3 and 0,5 micron.

Jan 1, 1983

By Sheldon P. Wimpfen

Forecasting, an ancient art, is con-ducted by everyone in varying degrees. It is a vital aspect of mineral production and conditions must be predicted over a long time frame in all aspects of the industry from exploration to plant construction. Although many government agencies as well as private industry make forecasts, there are insufficent "make good" analyses performed. The performance of more such studies could sharpen forecasting ability.

Jan 1, 1983

By Armstrong

This is a world of change and has been from the beginning. There are constant efforts on the part of natural forces to wear down the high spots and fill in the low spots. Wind and water over eons of time tunnel through obstacles and build windways and waterways to make movement of air and water easier and more efficient. It is a natural, never ending, ever changing continuing effort. Man in his struggle to survive, and to progress, has had to adapt the terrain of the earth to fit his needs the best he could. First, he used natural caves to protect him from the elements; then he learned how to build earth and rock-moving tools from antlers, bone, rocks, and sticks and adapted his cave to increase his security and provide better protection from heat and cold and from his predatory enemies. As his numbers increased, so did the necessity of further adapting his environment to accommodate his needs. Water was usually not available when and where needed, especially in the desert areas where civilization developed, and long tunnels were drilled to intercept ground waters and lead them to underground caves carved out of soft limestone. Most of the tunnels of early man were to bring water from where it was to where man needed it. Then, as now, as man increased his chances for physical survival, he turned to the quality of life -- and this reflected in the concern for life after death. This lead to the elaborate shafts and tunnels for the protection and prservation of the more affluent noblemen and pharaohs of the early Egyptian civilization. Man used the underground for the stable temperature and for protection and safety.

Jan 1, 1974

By William R. Yernberg

The Fifth International Conference on acid rock drainage (ICARD 2000) was held May 21-24, 2000, in Denver, CO. The three-day conference consisted of about 150 oral presentations and poster sessions that described the state-of-the-art of acid-rock-drainage (ARD) science and technology. The conference also featured a trade show. It included representatives from consulting companies and government agencies with interests in ARD, as well as other environmental issues related to mining. The conference also included field trips to ARD treatment sites and short courses on acid rock drainage issues. ICARD 2000 was planned and promoted by the ICARD 2000 Organizing Committee and the Society for Mining, Metallurgy, and Exploration, Inc. (SME). Financial support was provided by Barrick Gold, BHP Copper, Homestake Mining, Noranda, Phelps Dodge, PlacerDome, the US Bureau of Land Management, the USEnvironmental Protection Agency and the US Geological Survey. Since the original ICARD was held in Roros, Norway, in 1988, knowledge has improved of the behavior of mine wastes as have methods of environmental mitigation. The ICARD 2000 presented the latest advancements in the field of acid drainage.

Jan 1, 2000

By J. B. Stockton, D. J. Robbins, E. T. Woodburn

Batch flotation data in an equilibrium cell show that beneficiation improves with froth drainage. The limiting lamella thickness in a well- drained 3-phase coal froth appears to be determined for ultra-fine particles (-45µm) by the d90 particle size. The froth stability is considered to depend on the existence of a very thin liquid film between the outer surfaces of the d90 particles and the bounding bubble interfaces of the lamella in which the particle is held. The dependence of the coalescence rate of bubbles in these froths on the residual surfactant concentration in the lamella liquid is then consistent with stability analyses for two-phase foams.

Jan 1, 1988

By H. Maleki, G. Tetreault

This study was initiated by the Bureau of Land Management (BLM) to develop guidelines for determining the maximum economic recovery of resources in coal mines. The work was in response to a requirement in the Mineral Leasing Act of 1920 and Federal regulations. The intent was to address the economic rainability of small, irregular reserves in existing longwall mines. In particular, there was a need to determine if room-and-pillar mining using a continuous miner (CM method) was economically sound, or whether unconventional (short or odd-shaped) longwalls could be used to recover small coal reserves economically. Small reserves, called "widgets" are left in longwall mines on one side of the mains, near outcrops and adverse geological conditions, or near any other location where reserve geometry does not lend itself to mining with a rectangular longwall panel. The work included (1) analysis of the geologic, geo-technical, and economic factors that influence the recovery of small coal reserves, (2) analysis of historic changes in supply, demand, and coal prices, (3) development of typical cost models for room-and-pillar and longwall mines, and (4) development of a practical methodology for determining maximum economic recovery. The methodology included an evaluation of the ratio of coal mined during longwall mining to that mined for development (LDR) as well as costs of maintaining coal quality depending on market conditions. The LDR is a good indicator of mine efficiency and overall coal recovery in modem longwall mines and thus is used to evaluate the

Jan 1, 2001

By Earl F. Mathers

Few people would question that coal is king in the Campbell County, WY area. Other industries, such as oil production and ranching, also contribute significantly to the economic base, but coal mining and related industry development dominate. In recent years, Gillette has become the commercial hub of northeastern Wyoming. This development has been largely a response to the growth of the coal industry in Campbell County. Historically, Campbell County developed as a ranching area, a process that was aided by the passage of rail lines through the area, allowing early ranching interests to get their livestock to market. For decades, the Gillette-Campbell County area was predominantly a ranching area that experienced only incremental population growth.

Jan 1, 1994

By Ava Segal, Doga Cagdas Demirkan, Abhidipta Mallik, Sebnem Duzgun, Andrew J. Petruska

Search and rescue operations in mining heavily rely on humans. In the context of emergency situations within underground tunnels, the potential to utilize sensory technology for navigation assistance holds the promise of saving human lives. Our research introduces a device configuration designed to enhance the performance of search and rescue teams. This setup integrates LIDAR and thermal cameras with the Microsoft Hololens, facilitated by the NUC computer and ROS Bridge. Performance assessment involves quantifying the extent to which a user is willing to venture into a light-deprived section of the mine prior to necessitating supplementary illumination. The preliminary outcomes highlight the significant potential of augmented reality assistance in offering indispensable aid to first responders, thereby greatly augmenting the efficiency of search and rescue missions conducted during critical circumstances.

Feb 1, 2024

By Z. M. Zavodni, M. K. McCarter

This paper identifies physical conditions responsible for past instability of the Main Hill area in Kennecott Copper Corporation&apos;s Bingham Canyon Mine, Bingham Canyon, Utah, and describes successful stabilization techniques employed in this slide zone. Geotechnical highlights of recent slides are presented, including monitoring, geological engineering data collection, hydrology, physical rock properties, and stability analyses. Local conditions responsible for slope movement in the Main Hill zone are: (1) high pore water pressure that causes a substantial decrease in real and effective material strengths; (2) continuous structural systems that allow sliding in the more competent rock zones; and (3) broad areas containing fractured, altered , and incompetent rock and soil- like materials. The failure mode is structurally controlled and involves a circular-type soil failure in the toe region initiated by excessive pore water pressure. A surface mapping method is presented which assigns rock mass quality on the basis of block size and rock substance strength. This site characterization technique has successfully predicted slide boundaries and failure modes; used in conjunction with laboratory determined shear strengths, it has provided basic input for calculating slope safety factors in the Main Hill slide zone.

Jan 1, 1977

By A. Henchiri, G. A. Gruber

INTRODUCTION Phosphatic resources may be quantified in terms of ore tons and phosphate analyses; however, to quantify phosphate reserves it is necessary to estimate the tons and quality of phosphate rock that can be extracted from the ore. The yield and grade of phosphate rock that can recovered from sedimentary phosphate deposits are usually difficult to estimate because of variations in stratigraphy and/or mineralogy. Prospecting phosphorite ores for purposes of estimating reserves and preparing mine plans requires considerably more effort than defining ore thickness and P205 content. In Florida, for example, it is standard practice to prospect by core drilling and to subject each strata (split) to beneficiation testing, and to perform detailed chemical analyses on the beneficiated products from each strata. For a completed drilling pattern the area of influence of each hole is 2.5 acres. The number of strata per drill hole typically varies from two to five, and thus complete prospecting of a 40acre tract requires drilling 16 core holes and beneficiation testing of about 48 ore samples. Florida practice is not appropriate for all phosphorite deposits. Functional drill rigs and trained drillers may not be readily available. Water for core drilling may be unavailable and the characteristics of either the overburden or ore may require careful attention and excessive cost to obtain representative core samples. Alternate ore sampling methods include auger drilling, rotary drilling to obtain cuttings, and the excavation of trenches, pits, and shafts. Drill cuttings samples are generally the least expensive to obtain, but they are usually unsuitable for beneficiation testing because of particle size reduction during drilling. Ore samples from surface trenches and pits are expensive and may not be representative of deeper ore. Ore samples from shafts are the most expensive to obtain, but if taken properly they are reliable for use in laboratory and pilot plant testing. Regardless of the prospecting technique used, reliable estimates of the yield and grade of phosphate rock that can be extracted from an ore deposit are required: • to justify capital expenditures for a new mine • for mine design and mine planning • for beneficiation plant design • for production forecasts, quality control, and marketing. This paper describes models that predict the beneficiation response of ores from three phosphate ore deposits. The purpose of these models is to obtain maximum utilization of available prospect data with the least cost. ORE DEPOSITS Simple beneficiation models have been developed for ores from three sedimentary phosphate deposits around the Mediterranean area. The first deposit, herein described as "A" ore, is located north of the Mediterranean Sea. The second deposit, designated as "B" ore, is located east of the Mediterranean Sea, while the third deposit, "C" ore, is located south of the Mediterranean Sea. Ore "C" is from the Sra Ouertane deposit in northwestern Tunisia.

Jan 1, 1993

By MSHA

Not quite a year ago, during a speech to a group of mining professionals in Washington, DC, the subject centered around the long-range importance of conducting research projects and how much that research needs to specifically apply to health and safety matters in our industry. The point was made about the critical need to work together with government, private industry, labor organizations and academia speaking with a unified voice as we all march into the future together. The fundamental benefits of competitive research were mentioned -- to improve our quality of life, to develop our energy resources, to achieve a safe and healthy environment and to ensure long-term economic growth. Very importantly, emphasis was given to the natural link that makes my agency, the Mine Safety and Health Administration, and the National Institute for Occupational Safety and Health -- NIOSH -- the beneficiaries of each other&apos;s findings.

Jan 1, 1999

By S. Ostap

INTRODUCTION Paradoxically, it has been found that the people who are the most aware of the origin, mineralogy and composition of bauxite are also the people who are the least aware of how bauxite composition affects its treatment by the Bayer process. These people are the exploration and mining geologists normally associated with aluminum producing companies. The purpose of this paper is to give some idea of how the concentration and physical nature of the different minerals found in bauxites affect the operation of the Bayer process used to extract their alumina content. The bauxites we will consider here will be only the tropical bauxites such as occurring in Jamaica, various countries in South America i.e. Guyana, Surinam, Brazil, African bauxites, Malaysia and in Australia. When we speak of the Bayer process, it will be the North American version of the Bayer process using low caustic concentrations and bauxite digestion temperatures varying between 130° to 250°C. TABLE 1 shows the minerals and elements of interest occurring in tropical bauxites. The minerals and elements listed in the table do not by any means represent all of those identified in bauxites. Using mass spectrographic analysis on six bauxites from different geographic locations, we managed to identify between 50-60 different elements. Fortunately, only about 13-14 of these elements possess the necessary chemical properties to be able to accumulate in caustic Bayer solutions. The remainder are either not attacked, or form insoluble reaction products with some main liquor component, i.e., hydroxide, aluminate or carbonate, or reprecipitate with alumina trihydrate during the precipitation stage.

Jan 1, 1984