Search Documents

By F. Habashi

The phosphate fertilizer industry is at present based mainly on the use of sulfuric acid. This technology results in the generation of large amounts of radioactive gypsum that represents disposal and environmental problems. Also it involves the use of expensive reactors for acidification that necessitates the frequent replacing the damaged agitators. Applying hydrometallurgical techniques such as in-situ, heap, or vat leaching to phosphate processing could solve these problems. In this case, however, nitric acid must be used and dicalcium phosphate (40% P2O5) may be obtained as a final product. It is insoluble in water but soluble in citric acid and is an excellent fertilizer. This technology does not interfere with uranium recovery if desired. In addition it permits the recovery of rare earths which are otherwise lost in the gypsum.

Jan 1, 2011

By Shimi Tzobery, Jay Davenport, Raymond Henn, Sam Bandimere

Over the past several decades, the use of cement-based grouts using ultra fine cement as a replacement for portland cement has begun to gain acceptance as an alternative to chemical solution grouts used in permeation grouting. The amount of information currently available on grouts made with ultrafine cement is limited. The authors used a previously developed field testing program to perform additional tests to evaluate the permeation performance of portland and ultrafine cement-based grouts. For the first time, the 2003 testing program included an attempt to determine the 28 day compressive strength of the sand permeated by the grout.

Jan 1, 2005

By James M. Murphy

INTRODUCTION In the fall of 1983, the fourth new Rapid Transit System constructed in this country in the last forty years will go into revenue service. The Baltimore Metro will bring to this major Mid-Atlantic seaport the first phase of a planned intermodal transit system, serving a metropolitan area with a population in excess of four million people. Originally, the Mass Transit Administration (MTA) considered construction of a twenty-eight mile system known as Phase 1. Its two lines would run from the center of Baltimore City, one going northwest to Owings Mills and the other south to Anne Arundel County. Legislative approval was granted in April, 1976; however, funding was limited to constructing a segment fewer than eight miles in length, along the northwest corridor from Charles Center to the Baltimore City county line. This segment is known as Section A. The project is 80% federally funded and 20% state funded, with a capital cost estimate of $797,000,000 to complete. This report addresses the development and implementation of a Coordinated Insurance Program for the construction phase of Section A, and includes a description of the associated risk management process. GENERAL DESCRIPTION OF SECTION A Section A of the Baltimore Metro is composed of a rapid transit line eight miles in length which serves the northwest corridor between Charles Center in downtown Baltimore and Reisterstown Plaza at the Baltimore City county boundary. The line is completely grade separated and, once operational, will provide high speed automated rapid

Jan 1, 1983

he leaching behavior of palladium in ammoniacal solutions has been investigated by using the rotating disk technique in an autoclave. The study included the effect of rotating speed, temperature, oxygen pressure, composition of ammoniacal solutions, and catalyst on the overall leaching rate. The dissolution of palladium in ammoniacal solutions was discussed in view of the thermodynamics and a kinetic model. Even though the potential-pH diagram suggests that palladium metal can dissolve in ammoniacal solutions at room temperature, it was found that the dissolution was too slow at temperatures below 100°C but was significantly improved at higher temperatures. It was also found that the rotating speed of palladium disk had no effect on the leaching rate. The apparent activation energy was found to be 69.7 kJ/mole. Based on the results obtained, it is concluded that the dissolution of palladium is controlled by chemical reaction.

Jan 1, 1997

By S. K. Kawatra

In this paper three methods of on-stream analysis 1) Radiometric techniques, 2) X-ray tube techniques and 3) Neutron activation method are reviewed. Advantages and disadvantages of each method are discussed.

Jan 1, 1984

By Hassan El-Shall, Abbas A. Zaman, Brij M. Moudgil

The addition of organic and inorganic dispersants to aqueous suspensions of heterogeneous particles (kaolin) was found to significantly affect the solubility of metal ions from kaolin particles and stability of the dispersion. In most of the industrial applications of kaolin, highly concentrated slurries of controlled stability and fluidity are required. The solubility of kaolin particles in terms of aluminum and silicon ions and its effect on the stability of the slurry was investigated. The main objectives of this study were (1) to study the effect of the extracted metals on the properties and performance of the slurry, (2) to understand the reaction mechanism of dissolution of metals from kaolin, and (3) to understand the interaction mechanism of dispersants with kaolin particles. The controlling variables were dispersant dosage, slurry pH, solids loading, and aging.

Jan 1, 2003

Face and pillar bursts, bumps and bounces are violent failures that occur in underground coal mines in response to a complicated interplay of face and pillar geometry, seam depth, coal properties and interactions between roof, seam and floor strata. Additional complications arise from the presence of gas, mainly methane, and associated pressure and flow that vary with time and are further influenced by the rate of face advance. Where gas plays a dominant role, the term outburst is often used; where stress concentration is primary, terms such as burst, bump or bounce may be used. Hargraves [1983] presents an often cited review of outburst phenomena with emphasis on Australian conditions. Beamish and Crosdale [1998] indicate outbursts have occurred for over a hundred years and present tabulations of outburst numbers in major coal basins throughout the world. A central consideration is the rate of depressurization that occurs in the course of mining. Outbursts are not limited to coal seams and adjacent strata; they also occur in salt and potash mines [Molinda et al 1988]. Stress concentration and gas pressure act in consort, so the combined action is important to understanding the mechanics of bursts or outbursts and to the development of measures to reduce the associated hazard. Gas flow is a complicated phenomenon associated with diffusion of gas from micro-pores and the flow of gas along cleats. Laboratory measurements indicate both are dependent on stress and pressure [Harpalani and Ouyang 1998]. Moreover, gas permeability in porous media is often many times water permeability [Klinkenberg 1941]. However, there is also evidence that gas and water permeability are similar at elevated stress and follow Darcy?s law [Dabous et al]. Gas flow is also of importance to mine ventilation. Price et al [1973] in cooperation with personnel of the former U.S. Bureau of Mines developed finite difference models to estimate methane emission in mines in the Pocahontas No. 3 and Pittsburg seams using a premining pressure of 4.69 MPa (680 psi) and Darcy's law implying laminar flow. However, the effects of stress were not taken into account. In this regard, mine measurements of permeability are usually based on Darcy?s law [Peide 1990]. Early models of gas flow with stress effects were one-dimensional in space and time (x,t) and were developed with the goal of estimating the gas pressure profile from the face into the seam as time passed [Schlanger and Paterson 1987, Zou and Yu, 1999]. A zone of high permeability adjacent to the mining face was recognized in these early models. Later models based on the popular finite element method allowed two spatial dimensions (x,y) and variation in time (t) and for coal seam heterogeneity [Tang et al, 2002]. Zhu et al [2007] formulated a set of nonlinear equations involving a complicated stress-pressure-permeability relationship for application to coal seam gas flow and concluded the coupling was important but failure of coal should also be considered. Wold et al [2008] used a hybrid finite difference - finite element model interleaved with a reservoir simulation model to study outbursts based on extensive mine and laboratory measurements. An important feature of the modeling was the use of spatially variable material properties and Monte Carlo simulation to obtain quantitative estimates of outburst conditions and probabilities. Connell [2009] used the same reservoir simulation model as Wold but used the popular finite difference code FLAC3D for hydro-mechanical responses to evaluate two permeability relationships, one depending on porosity and the other on stress, and concluded that permeability changes with gas production were more complex than computed by either permeability model. Gadde [2010] in an integrated laboratory and field study of coal pillar strength explored the effect of spatial variability and concluded that design based on average strength was acceptable in some circumstances, although gas pressure was not an issue. Liu et al [2011] also applied a FLAC code to analyze two-dimensional gas flow and deformation of layered but homogeneous strata in a Chinese coal mine using a strain-softening model and concluded that damage and gas pressure were important to strata safety relative to the case without gas.

Feb 27, 2013

By Richard Kastner, Emilie Vanoudheusden, Fabrice Emeriault, Jacques Robert

INTRODUCTION The subway line B of Toulouse (France) has been realized with three different tunnel boring machines (TBM) techniques: Contracts 2 and 5 are excavated with earth-pressure balanced TBM, Contract 4 with a slurry shield TBM, and Contract 3 with a compressed-air TBM. The first three machines are around 7.7 m in diameter, while the last one is 5.3 m. Moreover, a small part of the line (50 m) has been excavated by a conventional method. The tunnels run through the Toulouse molasses, composed of hard sandy clay with pockets and lenses of dense sand. Geotechnical investigations have shown that in these formations, K0 is greater than 1, around 1.8 at a depth of 25 m (Serratrice,2005) and that geotechnical characteristics are homogenous on the whole layout (? =22 kN/m3, Su = 300 kPa, c' = 30 kPa, F' = 32°). The water table is found between 2 and4 m below ground level. As geology, stratigraphy and tunnel cover (between 10 and 20 m) are almost identical, a comparison of movements induced by the excavation by each of the four excavation techniques is possible. This paper presents the soil mass movement measures in the case of the conventional excavation method and in the case of TBM sections. It shows how tunneling parameters may explain the different surface movements observed during excavation. For the sake of simplicity, only the results of Contract 2 (earth pressure balanced TBM)will be presented. MONITORING Monitoring for the Conventional Method Section For the conventional method section (Vanoudheusden et al. 2005) the mass soil movements are measured with two inclinometers and one multi-point extensometer borehole with automatic data acquisition (Figure 1). The monitoring devices include

Jan 1, 2007

By John Batchelder

The Copper Canyon Cu-Au-Ag deposits include two geologically distinct hypogene ore bodies developed primarily in late Paleozoic rocks adjacent to a 38-m.y.-old potassic-altered granodiorite, whose emplacement seems to have been controlled largely by the Virgin fault, a north-striking normal fault. Widespread but subeconomic concentrations of sulfides as fracture and cavity fillings in skarn apparently preceded the final intrusion of the granodiorite. In the west ore body, metals reached ore-grade concentrations through the massive replacement of andradite by chalcopyrite, pyrrhotite, and pyrite mineral assemblages. The east ore body probably formed after the granodiorite reached its present level. Calculated 6dD values of water in equilibrium with primary and secondary biotites range from -76 to -99 per mil at temperatures indicated by d180 values from coexisting quartz and biotite. The lightest values are in secondary biotite from the east ore body. These data suggest that fluids associated with potassic alteration here were most likely composed of magmatic water mixed with some meteoric water.

Jan 1, 1976

By A. C. Smith

Although only used in a few U.S. longwall mines, bleeder-less ventilation systems can be an effective spontaneous combustion control method in mines having a demonstrated history of spontaneous combustion. To provide insights for the optimization of bleederless ventilation systems for U.S. underground coal mines, a computational fluid dynamics (CFD) study was conducted to model the spontaneous heating in longwall gob areas using a bleederless ventilation system. A single longwall panel with a bleederless ventilation system was simulated, and typical longwall mine ventilation data were used in the simulations. The permeability and porosity profiles for the longwall gob were estimated using a geotechnical model and were used as inputs for the CFD modeling. The effects of gob permeability and resistance of the collapsed entries on the spontaneous heating were studied. The effectiveness of using nitrogen injection to prevent spontaneous heating in the gob was also examined.1

Jan 1, 2008

By Kevin Sierra, Orfelinda Avalo, Julio Guizado, Edwilde Yoplac, David Martinez

Mining tailings are slurry byproducts of mineral recovery. They generate serious environmental risks due to their toxicity when exposed to water and oxygen. Studies focus on eco-friendly alternatives for mitigating these environmental impacts. Processing these tailings enables a sustainable mineral production model through circular economy practices. This study evaluates using gold mining tailings to recover gold and produce bricks. Flotation tests obtained a concentrate with 86.66% gold recovery, containing sulfides (pyrite, arsenopyrite) and a tailing with silicates and oxides suitable for brick manufacturing and ornamental pieces. This approach promotes eco-friendly solutions and a greener approach to mining operations.

Feb 1, 2024

By A. Fleming

The exploration process, like any other commercial activity, can only succeed if the objective of the exercise is clearly defined and persistently pursued. Successful exploration requires properties, funding, personnel and persistence. Many of us have years of experience in conducting exploration in our countries of residence. Conducting exploration in a foreign country, however, requires a number of significant other criteria.

Jan 1, 1997

By George A. Savanick

The objective of this paper is to review advances in the art of borehole (slurry) mining made by the Bureau of Mines. The introduction gives historical and general background information on borehole mining. The borehole mining concept is defined and justified in terms of economics, health and safety, the environment, and resource conservation. This is followed by a description of the design of a prototype borehole mining tool (BMT) developed by the Bureau of Mines. Included are design drawings and performance specifications. The next section describes the application of the BMT in the extraction of metallurgical coal from steeply pitching seams near Wilkeson, Wash., during 1975-76. The field test showed that the BMT produced coal at the rate of 8 tons per hour (tph) (7,272 kg/hr) from a depth of 88 feet (26.8 m) and was effective in producing coal as far as 15 feet (4.6 m) from the center of the borehole. The data are used as a basis for an economic analysis of borehole coal mining and for the suggestions for the design of a second-generation borehole coal mining tool. The following section describes Bureau efforts in applying borehole mining to the extraction of uraniferous sandstone at Rocky Mountain Energy Corp.'s Nine-Mile Lake site, Natrona County, Wyo. BMT design changes appropriate to uranium mining are described along with production, reliability, and reclamation data taken during 1977-73. The field test revealed that the BMT produced 900 tons (81.8x105 g) of uraniferous sand at an average race of 8 tph (7,272 kg/hr) from a depth of 75 (22.8 m) to 90 (27.4 m) feet and created a cavity 25 feet (7.6 m) in radius. These data are used as the basis for an economic analysis of borehole mining of shallow uraniferous sandstones. Reclamation data included will be the results of backfilling experiments conducted at Nine-Mile Lake during 1978. The most significant of these data were that backfill was emplaced at the rate of 16 tph (14.5x103 kg/hr) and that 90 percent of the material extracted from a cavity can be backfilled.

Jan 1, 1979

By L. Ozdemir, M. Cigla

This paper presents and discusses some of the computer models developed and currently used at the Earth Mechanics Institute (EMI) of the Colorado School of Mines (CSM). These include the performance models for full and partial face machines. Examples of input and output of these models will be illustrated for typical mining operations by using machines such as Tunnel Boring Machines (TBM), Continuous Miners (CM), Marietta borer miners and longwall drum shearers. The general approach to modeling and the available models are discussed and some examples of these models are presented. The comparison between the estimated and achieved performance, as well as the degree of improvement in the performance due to balancing and modification in cutterhead design are also discussed.

Jan 1, 2000

By Frank Kitzinger, Jacques Nantel

Under special circumstances, electrical energy can successfully replace chemical ex­plosives for blasting rock. High pressure plasma can be generated in the confines of a drillhole, by a powerful electrical dis­charge. The energy level can be adjusted to replicate the effect of a high explosive. The main difference is the almost total ab­sence of gas generation with electric blast­ing. Once the rock fractures, the small amount of matter used for generating the plasma rapidly cools off and regains its former volume. High speed film studies clearly show, that the initial speed of blasted rock fragments is the greatest, no further gas propelled acceleration takes place .. Figure 1, shows a typical electric blast of an oversize boulder of quarzite in an open pit mine.

Jan 1, 1992

By D. R. Nagaraj

Editor&apos;s note: Minerals concentration is a disparate area, one involving many disciplines. Flotation, flocculation, reagents, microbial processes, gravity and magnetic separation, and the areas of coal and oil shale - concentration is relevant to all of these. In his article, Nagaraj reviews the latest developments and findings in concentration that have ocurred during the past year. Flotation The Monograph Series "Development in Mineral Processing," (Elsevier, 1985) was devoted to "Flotation of Sulfide Minerals." This volume has 26 articles covering the aspects of flotation chemistry, process development, plant design and equipment, and modeling and process control. The numerous articles on sulfide flotation had one recurring theme - the role of electrochemical processes and redox potentials in flotation and depression. Significant advances have been made in this area. A differential desorption-reflotation process was developed for the beneficiation of calcitic phosphate pebble (Hsieh and Lehr, Industrial Engineering and Chemistry, 1985). The carbonate and phosphate minerals were first separated from silica using fatty acid and the modifiers diphosphonic acid and HF. The collector on phosphate was then desorbed using sulfuric acid, and calcite was selectively floated without additional collector. A two-stage conditioning - initially at pH 10, followed by that at pH < 4.5 - with sodium oleate was developed to improve the separation between apatite and dolomite (Moudgil and Chanchani, Minerals and Metallurgical Processing, MMP, 1985). Separation of Mussorie rock phosphate in India from gangue calcite, dolomite, silicates, pyrite, and carbonaceous impurities was achieved with a three-stage flotation only on -75 µm (-200 mesh) fraction (Vaman Rao et al., International Journal of Mineral Processing, IJMP, 1985). The separation of fine SiC whiskers from other products of coked rice hulls by immiscible liquid and froth flotation was achieved using M1BC, pine oil, and mineral spirits (Parekh and Goldberger, MMP, 1985). Flotation was more economical. The carrier flotation separation of hematite fines from quartz fines was effected using coarse hematite as a carrier and oleic acid and ferric chloride (Cristoveanu and Meech, CIM Bulletin, 1985). Potash recovery from brines by laboratory-pan solar evaporation and amine flotation was discussed by Foot and Juiatt (Salts and Brines &apos;85, Proceedings, 1985). Flotation in a 45-kg/h (99-lb per hour) unit recovered more than 95% of the potash in schoenite and sylvite concentrates containing 28% and 62% K2O, respectively. The effects of fresh concrete into cement and aggregate by a single-step flotation process in aqueous suspension was described (Naegle, Chemical Engineering Science, 1985). The physico-chemical principles for the selective separation of proteins from mixtures using flotation were discussed by Ostermaier and Dobias (Colloids & Surfactants, 1985). Selective flocculation of hematite from silica was studied by Bagster and Mcllvenny (IJMP, 1985). Selective flocculation was more favorable with more highly charged anionic polyacrylamides and with high molecular weight. The cationic and non-ionic polymers flocculated both minerals. In minerals mixtures, there appeared to be very little selectivity unless a combination of dispersant and electrolyte was used. The effect of dissolved minerals species, such as Cu, Fe, and Ni on flocculation of chalcopyrite, pentlandite, millerite, pyrrhotite, and covellite was studied by Acar and Somasundaran (SME-AIME, 1985). Reagents There were some major advances made in reagent development for the minerals processing industry. Cyanamid introduced several classes of collectors, one of which - the diaryl monothiophosphates as acid circuit col¬lectors of sulfides and oxidesulfide ores - was commercialized in 1985. The monothiophosphates are more stable and powerful collectors than the xanthates and dithiophosphates. Hydrolyzed dithiophosphate containing 80% monothio and 20% dithiophosphate was found to give optimum recovery of copper from crude cementation precipitate and separation of Cu and Ni sulfides from matte (Akimova et al., Obogashch, Tonkov, Rud, OTR, 1985). A new class of O-alkyl-Nallyl

Jan 9, 1986

By A. Ramage

Since late 2010, CH2M HILL has been working with a confidential client who holds a long-term commitment to sustainable development (SD). The commitment is aligned with all three elements of the triple bottom line: people and society, ecosystems and environment, and financial and economic systems. These commitments are carried forward by the firm?s executives, managers, and operational sites, and are evident in materials posted on the company?s public website. These materials include a formal sustainability report prepared in accordance with the Global Reporting Initiative (GRI) guidelines (GRI, 2006), a report that outlines key SD challenges and progress toward the GRI targets, and a delineation of risks and opportunities outlined in the firm?s Form 10-K and Annual Report. In keeping with its commitments to SD targets, our client wished to consider SD issues in its decision processes for facility expansion or new projects. The company engaged CH2M HILL to meet this goal, based on working relationships established through existing contracts and CH2M HILL?s leading capabilities in sustainable solutions.

Jan 1, 2012

By William W. Leathen

Acid mine drainage became a reality through the exposure of the first bituminous coal seam, either by man or by nature. At first the small amount of acid formed was quickly and efficiently neutralized by basic rock strata and by neutral or alkaline water. As soon as extensive mining operations overtaxed nature&apos;s own defensive measures, acid mine drainage became a problem of concern to government and the coal industry. It was the purpose of the studies conducted at Mellon Institute to accumulate knowledge, both applied and fundamental, relating to the formation and disposal of acid mine effluents. It was during this program that the microbiology of acid mine water was studied. Most bituminous coal mine effluents are highly acidic and contain, along with other ions, high concentrations of ferrous iron. The acid is sulfuric, and. the iron is present as the sulfate; both are the oxidation products of iron sulfides (FeS2) which are present in the form of pyrites, marcasites, or other sulfuritic minerals. The oxidation occurs, in the absence of moisture, according to the following reaction: [ ]

Jan 1, 1959

By James A. Erdman

This overview briefly describes some examples of applications and difficulties in using plants that are drawn from the literature and from field experience. Because of the generally low Au concentra¬tions found in plants, the analysis of plant tissue is critical to the successful application of the biogeochemical method of prospecting. Neutron activation analysis is the most widely used method to detect Au in plants, due largely to its sensitivity; levels in the parts per billion range are easily attained. Two general types of sampling media are used in prospecting for Au: humus and living plants. Humus has been widely used in Canada, but the sampling of plants has increased there and elsewhere in recent years. The use of douglas-fir (Paeudotsuga menziesii) at a Au-bearing stockwork in Idaho is a prime example. A maximum Au concentration of 14 ppm was detected in the wood ash of this coniferous tree, well above the normal background concentration of about 0.15 ppm. Among shrubs that might be useful in Au prospecting, sagebrush or wormwood (genus Artemisia) could be sampled because it is extremely responsive to concealed mineralization. It has been used extensively in the Soviet Union and could be used in areas of the western United States where disseminated Au occurrences might be located. Among the problems one may encounter in using plants for Au prospecting are (1) physiological barriers, by which many plant species simply do not absorb Au at detectable levels; (2) misconceptions of soil-plant correlations; (3) localization of Au in plant tissue; and (4) the variation of Au concentrations due to season. Despite these limitations, biogeochemical techniques can complement or replace other geochemical methods currently used.

Jan 1, 2013

By Corby G. Anderson, Sheikh Abdul Rezan Sheikh Abdul Hamid, Sanjith Udayakumar, Ahmad Fauzi Mohd Noor, Teuku Andika Rama Putra

Chemical and mineralogical characterization of Malaysian monazite, a phosphate mineral, bearing rare earth elements separated from the tin tailings originated from Ipoh, Perak, Malaysia, was performed in this paper. The study aims to collect detailed information on the chemical composition, crystal phases, and microstructure of the mineral monazite concentrate that would aid to optimize the subsequent hydrometallurgical processes for high-efficient separation of thorium and other associated rare earth elements. A systematic characterization study of the concentrate was conducted using techniques such as optical microscopy (OM), scanning electron microscopy (SEM) equipped with energy-dispersive X-ray spectroscopy (EDS), and Fourier-transform infrared spectroscopy (FTIR). These techniques analyzed the morphological details on the surface, elemental analysis, and mineral association assessment and identified the surface functionalization groups. The bulk composition and the mineral phases in which the elements are present were studied by wavelength-dispersive X-ray fluorescence (WD-XRF) and X-ray diffraction (XRD) studies respectively. The XRF analysis confirmed the presence of Ce, La, Nd, Pr, and Y (rare earth oxides: REO’s ~ 60 wt.%) while thorium dioxide (ThO2) accounted for 7 wt.% of the total composition. Traces of Ca, K, Al, Fe, Ti, and Mn were also confirmed by SEM elemental mapping. The XRD results confirmed that the concentrate was primarily composed of monazite (Ce, La, Nd, Th (PO4)) along with minor impurity phases of quartz. Automated mineralogical analysis was used as a confirmatory tool to corroborate the preliminary evidences. Based on the particle size distribution analysis supported by SEM, the majority of monazite grains were found to be present in the size range of 170–210 μm. Strong bands of PO4 and SiO4 were observed in the IR spectra corresponding to the phospho-silicate matrix of the REE mineral.