Search Documents

By Roberto J. Guardia, Ted Lewtas, Peter Rasmussen, Klaus Winkler

As part of the Lake Fort Smith Water Supply Dam Enlargement project, located in northwest Arkansas, microtunneling methods were used to install two side-by-side,1.53m (60-in) inside-diameter steel pipes between the intake structure shaft and the lake. The 46.6 m- (153 ft-) and 41.7 m- (137 ft-) long tunnels were excavated in Pennsylvanian sedimentary bedrock ranging from coarse sandstone to siltstone and shale-like claystone. The intake tunnels were constructed 18.3 m (60 ft) below lake level from the dry shaft. Special installation methods and procedures described herein were used to complete the lake taps. Installation difficulties that caused minor delays are also reviewed. After the excavation of the Intake shaft was completed, the two lake taps were installed in approximately ten weeks with the same microtunneling machine.

Jan 1, 2005

By Sidney L. Hansen

This report was written because of concerns of the possible error involved when stopping leakage is incorrectly assumed to be turbulent. It is common practice to use turbulent flow to characterize each airway branch for computer models of mine ventilation circuits. This report addresses computer methods to accurately model air-leakage paths. A graphical method is described for deriving the equations of leakage through stoppings. The significance of modeling leakage according to the proper flow regime (turbulent or laminar) is demonstrated by the following method. A hypothetical mine was developed to represent present-day conditions. The stoppings of the mine were chosen to leak according to laminar flow properties. The mine was represented by constructing two base models. One base model used turbulent leakage equations for each stopping, while allowing the corresponding resistances to vary. The other base model used the correct laminar leakage equations and held corresponding resistances constant. The mine circuit was then expanded to demonstrate future development. The expanded portion was designed with stoppings that were identical to those in the base mine. The mine in the future state was represented by two projection models. Each projection model was an extended version of its associated base model; one used turbulent leakage equations and one used laminar leakage equations for stoppings. The laminar projection was theoretically correct and is used as a basis for comparison of differences in airflow quantities. Rather than modeling every leakage path for stoppings, a more practical approach is also discussed. A good level of accuracy is maintained by combining leakage paths if the proper flow equations are used. This method was used on the hypothetical mine projection and the flows were very similar to the theoretical values.

Jan 1, 1989

By M. G. Ayat

Coal degradation is the breakage of coal particles to finer sizes due to the continuous forces of attrition and gravity to which coal is subjected during mining, handling and preparation. The objective of this paper is to determine the extent of degradation that a coal slurry experiences when transported through pumps and pipelines. The examination of degradation results for a number of different coal slurries have indicated that the extent of breakage is dependent upon the physical properties of coal and the time span of circulation. These results have also indicated that certain size fractions of coal are more susceptible to breakage than others.

Jan 1, 1986

By A. E. Koski

This paper describes the implementation of specialized software in mine planning at the Cleveland-Cliffs’ managed Empire Mine on Michigan’s Marquette Iron Range. The application puts together years of mining experience on the eastern end of the Marquette Range beginning in the early 1960’s. The Empire Mine, in its thirty-fifth year of production, uses the software to model a complex and highly variable low grade magnetite orebody, capturing the economics of mining and processing to the final product. With special attention given to geostatistical methods, the software is used for all geologic modeling, ore reserve estimation, ore control, pit design and short and long range planning.

Jan 1, 1999

By Carl Johnson, D. R. Todd

The Blue Ridge Low Level Outlet (LLO) was a design/build contract to provide a secondary means of discharging water from the Blue Ridge Reservoir. The project involved driving a 3.25 m (11 ft) modified horseshoe tunnel by 293.5 m (963 ft) long utilizing conventional drill and blast methodology. The intake shaft and structure were constructed inside of a sheet pile cofferdam surrounded by a maximum of 20.1 m (66 ft) of water. The shaft was excavated 4.87 m(16 ft) diameter to a depth of 12.8 m (42 ft) below the tremie slab elevation. Steel lining, including a transition from 3.66 m to 2.74 m (12 to 9 ft) diameter and a90 degree elbow were installed in the inlet shaft and then backfilled with concrete. This paper will describe the RFP phase, the design phase, challenges of the underground construction and contractual challenges.

Jan 1, 2005

By B. J. Schat, A. W. O. Bots, O. S. Langhorst

Amsterdam City Council is building a new metro line, the North–South Line. The line passes under Amsterdam Central Station (a listed building) about 18m below street level. The retaining wall that has to be built underneath the existing building is an innovative construction consisting of two rows of steel piles interspersed with a solid mass of overlapping jet grout columns: a composite ‘sandwich’ wall. This paper gives an overview of the approach taken to designing (computational models) and building the retaining wall. Special attention is paid to the observational method used for the construction of the jet grout columns.

Jan 1, 2007

By Jaye Pickarts, Bret Boster, Jack McPartland

Pegasus Minera de Chile, Ltda. is completing three phases of metallurgical evaluation on the Pullalli project to develop a preliminary process flowsheet. A project feasibility study is in progress. The feasibility study includes a proposed process flowsheet designed based on results from the multiple stages of metallurgical evaluation. Phases I and II of metallurgical evaluation included laboratory scale heap leach and milling cyanidation testwork on multiple drill core composites and bulk ore samples from the Pullalli Project. Phase Ill included pilot scale milling/cyanidation testwork on Pullalli drill core composites. The proposed flowsheet includes selective mining and separate processing of low grade and high grade ores. Low grade ore will be crushed and heap leached. High grade ore will be milled leached for 12 hours in an agitated cyanidation circuit. After 12 hours of leaching, sands and slimes will be separated and the sands will be washed using a counter current cyclone (CCC) circuit. Partially leached and washed sands will be added to the crushed low grade ore for heap leaching treatment and permanent placement. Partially leached slimes will be thickened in a high capacity thickener and will be processed in a CIP circuit. Leached slimes will be placed in a tailings impoundment.

Jan 1, 1996

By Charles A. McLean

Bucketline dredges are machines for excavating large relatively unconsolidated or weakly consolidated materials from below water level. They are at the upper end of the capital cost range and the lower end of the operating cost range for placer mining machines and have digging capacities, typically, of from 100 cubic yards of bank measure material per operating hour for a shallow digging dredge carrying 2 cubic foot buckets to 1500 cubic yards per hour for a large deep digging dredge with 33 cubic foot buckets. Bucketline dredges used in the mining industry have their mineral processing plants mounted aboard the digging hull. Since dredges are high capital cost items, they require large ore reserves, typically at least ten years. Because of their high capital cost they are usually operated around the clock and for as many months of the year as weather conditions will permit. Typically a well run dredge operating year round would be expected to operate for 600 hours per month. Dredges operated in cold climates cannot operate when the weather freezes the dredge pond or the gravels, and dredges operating at sea cannot operate when high waves might batter the digging ladder against the bottom or upset the mineral extraction process.

Jan 1, 1992

By R. H. Grau

NIOSH’s Pittsburgh Research Laboratory is currently involved in research to identify silica dust generation in underground metal/nonmetal mines. The ultimate goal of this research is to develop control technologies to reduce worker exposure to respirable silica dust. Commodities and job classifications with the highest silica dust exposure have been identified through analysis of the Mine Safety and Health Administration (MSHA) compliance dust sampling database. Dust surveys were conducted in an underground limestone and gold mine to investigate silica dust sources, generation levels, and controls being used. A summary of the mining operations, sampling procedures, resulting data, and suggested methods to improve the dust control will be provided.

Jan 1, 2002

By D. D. Harbuck

The US Bureau of Mines investigated germanium and gallium extraction from an ore containing 0.089% Ge and 0.036% Ga. While previous researchers concluded that a reducing agent, such as SO2 is needed to extract germanium and gallium from such ore, this research showed that high extractions (87% Ge, 97% Ga) were possible using sulfuric acid alone, if the acid concentration were properly controlled. This control was achieved using a two-stage countercurrent leach circuit. Microprobe analyses revealed that the non-extracted germanium is in solid solution with quartz, and therefore cannot be leached with SO2 or sulfuric acid.

Jan 1, 1991

By J. C. Judd, D. D. Harbuck, M. D. Odekirk

The US Bureau of Mines investigated germanium and gallium extraction from an ore containing 0.089% Ge and 0.036% Ga. While previous researchers concluded that a reducing agent, such as SO2 is needed to extract germanium and gallium from such ore, this research showed that high extractions (87% Ge, 97% Ga) were possible using sulfuric acid alone, if the acid concentration were properly controlled. This control was achieved using a two-stage countercurrent leach circuit. Microprobe analyses revealed that the non-extracted germanium is in solid solution with quartz, and therefore cannot be leached with SO2 or sulfuric acid.

Jan 1, 1992

By Takashi Sakaguchi, Takehiko Tsuruta, Akira Nakajima

Some attempts were made to recover gold from aqueous systems using immobilized persimmon tannin. This adsorbent adsorbed gold from solutions containing hydrogen tetrachloroaurate (III) with high efficiency, whereas there was minimal adsorption from solutions containing gold (I) sodium thiomalate and sodium dicyanoaurate (I). The adsorption of gold was rapid, and was affected by the pH of the solution, temperature, external gold concentration and amount of adsorbent. Adsorbed gold was easily desorbed with 1 M thiourea solution, indicating that immobilized persimmon tannin can be repeatedly re-used for the recovery of gold using adsorption-desorption cycles.

Jan 1, 1995

By W. McMahon

Following the Sago Mine accident, the Mine Safety and Health Administration (MSHA) asked the U.S. Army Engineer Research and Development Center to study several possible methane explosion scenarios in the Sago coal mine. The study used a 1-ft resolution map of the mine to produce a 3-dimensional (3-D) model of a portion of the mine, including the sealed area where the explosion occurred. An advanced 3-D computational fluid dynamics (CFD) code was used to calculate the explosion pressures within the sealed area, on the mine seals, and in nearby regions of the mine. Based on the best available information on methane concentrations and assumptions on homogeneity and on layering and mix composition, three separate initial conditions of methane-air concentrations and location were studied. This paper discusses the CFD modeling technique, the results of the calculations, the challenges of conducting this type of modeling, and the advantages and limitations of CFD modeling of accident investigations of mine explosions.

Jan 1, 2009

By K. G. Thomas

New developments in gold exploitation over the past few decades have been extensive and promise to be exciting for the foreseeable future. They cover all phases of gold mining from developments in mining, processing, computer and finance. This presentation will cover these different disciplines and show how Barrick Gold Corporation ("Barrick") has used these devel­opments to enhance shareholder wealth. The developments can be grouped into disciplines as shown in the following table.

Jan 1, 1996

By Larry H. Heflin

The Washington Metropolitan Area Transit Authority's Wheaton Station and tunnel design was completed and offered for bid in the Spring of 1983. The format was unique to the Authority: a four part, four fiscal year contract developed in response to funding limitations with construction divided into four stages allowing the maximum amount of work to be done each year for the funds available. The bid was based on the entire contract, but was orginally awarded for only the first year's work. Each year's work had a maximum funding limitation thus safe guarding the Authority from a grossly unbalanced bid. The Authority's estimate for this work was $83,871,524. The low bid came in at 61% of this for a total low bid of $51,512,058. The low bidder was ILBAU America Corporation whose home offices are in Austria. Following receipt of the bids (and resolution of objections cited by other bidders who felt that the job could not be done for the $51 Million dollar figure), a Notice-To-Proceed was given on October 5, 1983. The construction contract allows a Value Engineering Change Proposal, called a VECP which is initiated and developed by the contractor to change the drawings, specifications or other requirements of the contract. Among other things the VECP should decrease the contract price while maintaining the service life, reliability, ease of maintenance, and standardized features and appearance and not require an unacceptable extension of the contract time. A VECP must estimate the amount of the net savings

Jan 1, 1985

By John E. Wallace

A recent study by the New York Trap Rock Corporation has conclusively determined that the number of blasting complaints is directly related to the noise produced by the blast. In turn it has been known for some years that the noise produced by the blast is directly related to atmospheric structure of temperature, wind, and humidity in the vertical direction. Normally during daylight hours the temperature decreases with altitude at the rate of about five and one half degrees per thousand feet on a sunny day, and to somewhat lesser amounts on cloudy days. Consequently, sound travels slower with altitude because of the lower temperature, and the sound rays tend to bend skyward, and are soon dispersed in the atmosphere. Quite frequently, however, the temperature increases with altitude, and just the opposite effect is attained. That is sound rays are bent downward, and sometimes reach the ground with intensities approaching that at the source. When the temperature increases with altitude a temperature inversion is said to exist. Less frequently than these two atmospheric conditions a condition is observed where temperature remains constant with altitude. This is called an isothermal atmospheric condition, and sound passing through this type of atmosphere tends to travel in straight lines, neither bending upward nor downward. The sound will be greater than normal near the blast, but will dissipate rapidly with distance from the blast site with no zone or zones of silence.

Jan 1, 1962

By Xuchen Fan, Chenyang Zhou, Yuemin Zhao, Liang Dong, Chenlong Duan

A gas–solid fluidized bed using magnetite particles is an effective methodology for coal beneficiation in the field of dry coal cleaning. Broadening the size range of magnetite used in the bed decreases medium preparation cost. In this study, a tapered fluidized bed was used to investigate a magnetite particle size range of −0.5 + 0.074 mm. The results showed that a tapered fluidized bed effectively strengthens mixing of magnetite with a wide size range (−0.5 + 0.074 mm). The results of beneficiation experiments indicated that with increasing tapered angle, separation efficiency increased and then decreased. The highest separation efficiency was obtained at a tapered angle of 10°. The optimal results showed that the ash content of the concentrate decreased from 31.82% to 12.33% with a probable error of 0.11, which indicated that a tapered fluidized bed was efficient to improve fine coal beneficiation performance.

By A. E. Raddatz

The U.S. Department of the Interior, Bureau of Mines, is investigating methods for recovering tungsten from domestic resources. A calcine-quench-leach (CQL) technique was developed for the extraction of tungsten from the Golconda, Nevada, hot springs ores. The deposit contains disseminated tungsten, which cannot be beneficiated by conventional techniques and must be treated by hydrometallurgical methods. The CQL procedure consists of calcining the ore at 900° C for 3 hr, quenching in a solution containing 1.5 parts of NazCO3 and 1.5 parts of NaOH per part of WO3 in the ore and at a solution- to-ore ratio of 3 to 1, leaching at 200° C and at 250 psig for 3 hr, and filtering and washing the residue. A series of closed-circuit batch tests showed that 92 pct of the tungsten was extracted from a sample containing 2.32 pct WO3. The pregnant solution contained 11 q of W03/1.

Jan 1, 1982

By Kenneth L. Schellie

In preplanning the reclamation of a pit or quarry the geology of the site is the name of the game! The planner must know the parameters of the deposit, the quantity and kind of earth materials to be removed, and the amount and nature of the materials to be left behind or wasted as the result of processing the marketable product. With many states and most local jurisdictions requiring reclamation plans prior to the issuance of mining permits, the need for accurate and complete data concerning the geology of the site becomes increasingly important. The producer need only know that marketable materials are available in sufficient quantity to make the mining operation economically feasible-the planner, in order that the land may be reshaped for a useful purpose, must have reasonably precise information as to the dimensions and configurations of the pit or quarry following extraction and the amount and type of materials available on the site (or in some cases offsite as well). Therefore the geology of the site is of major significance in determining the land forms and use capabilities of the property upon completion of the mining process.

Jan 1, 1974

By James A. Procarione, Sandip K. Mukherjee

The Department of Mining Engineering, University of Utah, has developed a thermodynamic-based mine ventilation simulator capable of predicting or analyzing the climatic conditions in hot underground environments. This compressible flow model, besides analyzing an operationally and legally-constrained network for mass and pressure balance, also takes into account various existing and anticipated sources of heat. Presently, three major sources of heat have been incorporated in the model. These include autocompression, wall-rock heat, and heat from equipment. A unique feature of this simulator which makes it distinctly different from its existing predecessors is the mathematical technique utilized to solve the network problem. Advantage has been taken of newer, more sophisticated mathematical and programming techniques to accomplish accelerated convergence and network solution generation. This paper describes in detail the development of the simulator including the mathematical relationships and the techniques used to predict the initial and final thermodynamic states of the mine air after its interaction with heat sources. The algorithm for solution to the network, computer model description, and the input data and program execution requirements are presented. A simple hypothetical network is used as a case study to illustrate the application of this simulator.

Jan 1, 1987