Search Documents

By Shanming He, Jinliang Wang, Xiaoming Wang, Chunfa Liao

Large amounts of manganese-rich slag were generated from smelting low-grade manganese ore containing high iron and high phosphorus in electric furnace or blast furnace, which contain 25–40 mass% Mn. This paper describes an efficient hydrometallurgical process for the utilization of high manganese slag instead of conventional usage of pyrometallurgical route for manganese recovery. Pressure acid leaching of manganese-rich slag using air as pressurized gas is studied systematically. The effects of mass ratio of manganese-rich slag to pyrite, concentration of sulfuric acid, leaching temperature, partial air pressure, leaching time, and liquid-solid (L/S) ratio on the separation of manganese with other main impurity components were investigated comprehensively. Under the following optimal process conditions, weight of manganese-rich slag powder,100 g; mass ratio of manganese-rich slag to pyrite, 20:1; sulfuric acid concentration of 140 g/L; air pressure of 0.6 MPa; leaching temperature of 140 °C; leaching time of 1 h; L/S of 7:1; ore size of 75–80 μm; and stirring rate of 600 rpm, the extraction rate of Mn reached 94%, and the dissolution percentage of Si, Al, and Fe are as low as 2%, 6%, and 10%, respectively. The leaching slurry presented a good solid-liquid separation characteristic. The silicic acid formed during sulfuric acid leaching manganese silicates was converted to filterable dehydrated SiO2 particles which precipitated in the residue under the condition of higher temperature with higher pressure. The effect of adding pyrite may be to reduced iron ions and decreased the output of iron hydroxide colloid and also reduced MnO2 to manganese sulfate in sulfuric acid leaching. Thus the formation possibility of colloid such as silica gel and iron hydroxide was decreased, and higher yield of manganese sulfate could be achieved.

By Shanming He, Jinliang Wang, Xiaoming Wang, Chunfa Liao

Large amounts of manganese-rich slag were generated from smelting low-grade manganese ore containing high iron and high phosphorus in electric furnace or blast furnace, which contain 25–40 mass% Mn. This paper describes an efficient hydrometallurgical process for the utilization of high manganese slag instead of conventional usage of pyrometallurgical route for manganese recovery. Pressure acid leaching of manganese-rich slag using air as pressurized gas is studied systematically. The effects of mass ratio of manganese-rich slag to pyrite, concentration of sulfuric acid, leaching temperature, partial air pressure, leaching time, and liquid-solid (L/S) ratio on the separation of manganese with other main impurity components were investigated comprehensively. Under the following optimal process conditions, weight of manganese-rich slag powder,100 g; mass ratio of manganese-rich slag to pyrite, 20:1; sulfuric acid concentration of 140 g/L; air pressure of 0.6 MPa; leaching temperature of 140 °C; leaching time of 1 h; L/S of 7:1; ore size of 75–80 μm; and stirring rate of 600 rpm, the extraction rate of Mn reached 94%, and the dissolution percentage of Si, Al, and Fe are as low as 2%, 6%, and 10%, respectively. The leaching slurry presented a good solid-liquid separation characteristic. The silicic acid formed during sulfuric acid leaching manganese silicates was converted to filterable dehydrated SiO2 particles which precipitated in the residue under the condition of higher temperature with higher pressure. The effect of adding pyrite may be to reduced iron ions and decreased the output of iron hydroxide colloid and also reduced MnO2 to manganese sulfate in sulfuric acid leaching. Thus the formation possibility of colloid such as silica gel and iron hydroxide was decreased, and higher yield of manganese sulfate could be achieved.

"On-site research and development as well as in-situ testing are key factors to the successful implementation of new mining equipment and technology. Unfortunately the demands and necessities of research and development often conflict with the reality of mine production in operational mines, especially during early stages of research and development and the initial testing of new equipment. Several experimental mines under university supervision attend to this problem and provide a close-to- reality testing environment for the mining industry and mining equipment manufacturers. This paper gives an overview of the design and organization of such an underground testing area as well as of the wide range of possible operations it can facilitate at the example of the FLB Experimental and Teaching Mine (Forschungs- und Lehrbergwerk) at Technische Universität Bergakademie Freiberg, the central European underground research mine. INTRODUCTION As well as the Mining Engineering education follows the same pattern worldwide, the tasks and duties to be fulfilled by engineers in the productive mines are comparable around the globe. This also holds true for the technologies and equipment needed, both in surface and underground mines. Almost all mining equipment brands are being distributed worldwide. The tasks and challenges of guaranteeing an ever- increasing productivity at the mines, while simultaneously maintaining, respectively improving, safety standards, also in the developing countries and emerging economies, requests a constant development, improvement and adaption both of the engineering education and of R&D in technology and equipment. The increasing safety requirements at the mines, in combination with also increasing safety and liability policies, do often not allow a proper practical education of mining engineering students. At the same time, new technologies and equipment to be deployed / brought to the mines have to be fully functional in a production operation from the very first moment. Time losses like break-down time or even repair and maintenance breaks are often costly and, even when expected up to a certain degree with newly developed machines, have a wider negative impact on the neighboring operations and operations within that mine, thus often being unacceptable within the ongoing production process and extremely costly."

Jan 1, 2015

By K. J. Shoop

Coal-fired power plants in the U. S. produce approximately 20 million metric tons of Hue-gas desulfurization sludge every year. The sludge mainly consists of calcium sulfite and calcium sulfate. This can be converted to synthetic gypsum, which in principle could be a marketable commodity. However, many Hue-gas scrubbers produce sludges that do not meet the quality requirements of the gypsum industry, and so their sludges must be landfilled as a waste. If a suitable method can be developed for removing certain objectionable impurities from the sludge, it will then be possible to market the material instead of landfilling it. A sludge from a natural-oxidation scrubber was characterized, and the main contaminant was found to be calcium carbonate from unreacted limestone. Based on the particle size and the characteristics of the material, froth flotation was considered as a method for purifying the material. Since no flotation studies have ever been carried out to separate calcium carbonate particles from calcium sulfite or calcium sulfate particles, it was first necessary to select a suitable collecting reagent. Based on Zeta-potential studies, the most suitable reagent was found to be an octadecylamine-octadecylguanidine complex. Results are presented for flotation of calcium carbonate from scrubber sludge using this reagent, in a reverse-flotation process. The best results were obtained when the sludge was first pre-cleaned using a water-only cyclone to remove unfloatable coarse limestone, followed by froth flotation to remove fine limestone.

Jan 1, 1998

By D. Hodouin

The paper reviews approaches to estimate in a real time fashion consistent mass flowrates and assays, using data from the on-stream analyzers and flowmeters of a flotation circuit. Results obtained with one algorithm operating on-line with an industrial flotation circuit are presented.

Jan 1, 1996

By L. P. Meade

The need to feed an established talc mill from a crude are source located closer to the mill prompted the drilling in 1986 of a previously mapped talc-carbonate deposit. This talc-bearing rock had never been considered as a potential source of crude talc are because of the high carbonate content and other deleterious minerals that were observed in outcrops. Selective mining, in-pit grade control and creative processing has allowed this deposit to be developed into an orebody. By definition, an orebody has to be a source of positive cash flow. With industrial minerals, this is determined as much by market acceptance as by are tenor.

Jan 1, 1992

By G. A. Irdi

An automated method of microscopy for determining the pyrite size distribution on two base coals that were crushed to 28 mesh x 0 has been developed. Polished epoxy-bound coal pellets were prepared and examined by a Zeiss IBAS image analyzer utilizing a program developed from provided software. Pyrite size distribution determination is considered a necessary first step in pyrite characterization that could lead to successful predictions, by microscopy, of a coal's theoretical pyritic sulfur removal. Our research efforts to date have indicated that the IBP-S can be a reliable instrument for determining pyrite size distribution in crushed coal. A program was also developed to convert pyrite size data to a weight basis for comparisons to the results from chemical analyses. The problems encountered in our research and their solutions will be presented in the discussion.

Jan 1, 1986

By D. R. Wilburn

his summary of international mineral exploration activities for the year 2011 draws upon available information from industry sources, published literature and U.S. Geological Survey (USGS) specialists. The summary provides data on exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry and presents [ ] analyses of exploration activities performed by the mineral industry. Three sources of information are reported and analyzed in this annual review of international exploration: 1) budgetary statistics expressed in U.S. nominal dollars provided by Metals Economics Group (MEG) of Halifax, Nova Scotia; 2) regional and site-specific exploration activities that took place in 2011 as compiled by the USGS and 3) regional events including economic, social and political conditions that affected exploration activities, which were derived from published sources and unpublished discussions with USGS and industry specialists.

Jan 1, 2012

By G. W. Mannard

The large massive sulphide deposits present a formidable challenge to the economic geologist. They represent such huge concentrations of iron, sulphur, base metals and precious metals that it is difficult to conceive how they were derived from the crust or mantle of the Earth. The problem of the origin of massive sulphide deposits has generated a geological controversy which has lasted two hundred years and shows no sign of abating. The economic incentive to solve this problem is great, as the massive sulphide bodies are the moat important source of the world's zinc, lead, and silver, as well as yielding large amounts of copper and gold. Using the criteria of abundance, size, age distribution and gross value of contained metals, the predominant sub-group of the massive sulphide deposits is that which comprises the crudely conformable pyritic (or pyrrhotitic) deposits which occur in stratified volcanic and sedimentary rocks or their metamorphosed equivalents. Examples of this sub-group are: the Buchans, Bathurst, Noranda, Kidd Creek, Flin Plon and Sullivan deposits of Canada; the Mt. Isa and Broken Hill orebodies of Australia; the Cyprus, Rio Tinto, Meggen and Rammelsberg deposits of Europe; Ducktown and the United Verde in United States; and the Kuroko deposits of Japan.

Jan 1, 1973

It is widely accepted that particles stabilise flotation froths and that stable froths result in improved flotation performance. Predicting the effect of particle addition on froth stability is, however, challenging. Dynamic surface tension measurement using maximum bubble pressure presents an attractive technique to investigate the effect of surfactant and particles at the air-water interface. The range of bubble lifetimes that can be studied (typically 0.1 to 60 s) is analogous to variations in air rate in flotation cells, and the corresponding changes in surface tension give an indication to the diffusion and adsorption rates of particles at the interface. In this paper, we use dynamic surface tension measurements to investigate the effect of particles on bubble surfaces at the microscale and link this to bulk froth stability measurements carried out using a froth column. Using the maximum bubble pressure method, the results show that the addition of particles results in lower surface tension, both at the dynamic (i.e. short) bubble lifetimes and towards equilibrium (i.e. 60 s bubble lifetime). This corresponds with the bulk froth stability measurements, where the three-phase system yielded more stable froths than the surfactant only system. Furthermore, increased particle loading at the air-water interface, whether through higher surfactant concentrations or lower air rates (longer bubble lifetimes), gave lower surface tension and higher froth stability. This demonstrates the link between bubble loading and froth stability. It is proposed that the maximum bubble pressure technique can be used to predict froth stability for two- and three-phase systems, enabling the effect of particle loading to be accounted for and quantified. Moreover, the technique has the potential to allow rapid determination of particle and surfactant diffusion at the air-water interface and prediction of the corresponding effect on bulk froth behaviour.

By R. K. Will

Granite Construction Company operates a rock quarry in the rugged Santa Cruz Mountains of central California indicated in Figure 1. Open pit methods are used to mine decomposed granite which is processed to produce sand, gravel, decorative rock and asphalt. The quarry is located near the village of Felton about five miles inland from the coast of the Pacific Ocean, and is near the campus of the University of California at Santa Cruz and several California State Parks. The area is heavily forested and is considered by residents to be environmentally sensitive. Because of the scenic beauty of the area and proximity to the San Francisco Bay area, a project such as a quarry receives the attention of regional residents and environmental organizations.

Jan 1, 1994

Collaboration between education providers is the key to long-term sustainability and improved quality in mining education. The mining industry is now, more than ever, an industry doing business on a global basis. Staff are recruited by global mining companies in many different countries and can find themselves deployed anywhere in the world. The mining engineer of tomorrow must be willing to take on this international challenge, and must be educated to a level where he or she has a comprehensive grounding in technical aspects of mining engineering, but also a well-founded appreciation of management, social, environmental and cultural issues which may be encountered around the world. In order to deliver such an education, academic providers must collaborate at both a national and international level. This paper provides an overview of progress that has been made in Australia through the national joint venture ? Mining Education Australia (MEA). Supported by the mining industry in Australia, through the Minerals Council of Australia (MCA), MEA has now been operational since 2007 and is seeing the development of a range of innovative courses and delivery methods, together with a high level of staff co-operation across the country. MEA has also now commenced some international teaching initiatives which are seen as a catalyst for a far greater degree of international collaboration in the future. Such activity is not only to the benefit of the students who are taught by experts from around the world, but it also ensures that individual university programs remain viable in terms of staffing numbers and financial performance. The paper also presents some statistics on recent upward trends in mining engineering student numbers from around the world, in response to the global shortage of mining engineers.

Jan 1, 2009

By Ulrich Kappus

The purpose of the project is to divert flood flows of North Potato Creek. The project is located in the southeast corner of Tennessee near Copperhill, approximately 160 kilometers north of Atlanta, Georgia. The project consists of: a 28-meter high dam, a 90-centimeter diameter outlet conduit; an emergency spillway; and a 4.0-meter diameter hard rock trans-basin diversion tunnel. This floodwater management system was part of Cities Service Company mine safety program for the Cherokee orebody which is partially located within the stream channel. The following paper describes the entire project development from feasibility studies to design and construction management.

Jan 1, 1978

By P. Amelunxen

Over the past several years, the combination of higher energy and steel costs and the recent commercial deployment of high-pressure grinding rolls (HPGR) technology in hard rock mining have led many multinational mining companies to evaluate the suitability of HPGR technology for their particular comminution circuits. HPGR technology is perceived to require a higher capital investment while delivering lower long-term operating costs. This paper undertakes a critical evaluation of this perception. By evaluating the capital and life-of-mine operating costs of competing circuit designs for soft, medium and hard ores, the HPGR break-even point can be identified, at which the incremental capital cost of an HPGR circuit is equivalent to the net present value of the projected operating cost reductions. For ores with hardness parameters above the break-even point, HPGR circuits could offer economic benefits, while for softer ores, SAG mill/ball mill/pebble crushing (SABC) circuits are likely to be more economical and energy efficient. This evaluation considers both an SABC reference circuit and a traditional stage crushing configuration. Other influential factors are also discussed.

Jan 1, 2011

By T. Gollaher

The use of paste thickeners for mineral tailings has gained increasing acceptance by the mining industry throughout the world and in the U.S. during the last five years. Advantages of water recovery and environmental sustainability are the driving forces for paste as an alternative to conventional thickening and the slurry pond. This paper presents a summary of the differences between paste and conventional tailings thickeners, along with recent examples of full-scale paste thickener installations.

Jan 1, 2010

By Liming Yuan

To reduce fire hazards from spontaneous combustion of coal in longwall gob areas, a series of computational fluid dynamics (CFD) simulations were conducted by the National Institute for Occupational Safety and Health (NIOSH) to model the spontaneous heating of coal in longwall gob areas. The previous modeling results demonstrate that spontaneous heating of coal usually occurred behind the longwall shields and along the face with a bleeder ventilation system. Assuming a stationary longwall face, the spontaneous heating could turn to a spontaneous fire in several days for the most reactive coal under favorable conditions. When the longwall face advances, the spontaneous heating process will be significantly affected. In this study, the effect of longwall face advance on the spontaneous heating in the gob area is investigated using the CFD model developed in previous studies. One longwall panel with a bleeder ventilation system is simulated. The width of the panel is 300 m (984 ft), while the length of the panel is changed between 1,000 to 2,000 m (3,280 to 6,560 ft). The same permeability and porosity profiles are used for gobs with different lengths. The spontaneous heating first develops in the gob when the longwall face is stationary. Then, the face advances at a certain rate. The face advance is simulated as a series of discrete movements, and the effect of the face advance on the maximum temperature developed during the face stoppage is examined.

Jan 3, 2010

By James R. Arnold, Cindy S. Jones, Michael F. Gleason, John O. Marsden, John G. Mansanti

INTRODUCTION The Chimney Creek Gold Mine (Gold Fields Operating Co. - Chimney Creek) is located 47 miles northeast of Winnemucca, Nevada, at the northern end of the Osgood Mountains. The operation is a wholly owned subsidiary of Gold Fields Mining Corporation, the North American branch of Consolidated Gold Fields PLC, London, England. The plant started up in November, 1987, less than three years after discovery of the orebody and three months ahead of schedule. Ore is mined in an open pit and is processed by combined dump leaching and milling techniques for gold and silver recovery. The mine is set to produce approximately 150.000 ounces of gold and 50,000 ounces of silver per year over a 12 year life at current reserve estimations. The mine was designed and constructed at a cost of $79.3 million with engineering and construction services provided by Davy McKee Corporation, San Ramon, California. Key Gold Fields operating staff were involved in the design of the facility from the start of the project: The Mine Manager, Plant Superintendent, Plant General Foreman, Maintenance General Foreman and Chief Metallurgist were all involved full time on the project within 5 months of the first ore discovery. Emphasis was directed at optimizing operating efficiency and in particular minimizing labor costs in the plant. It was recognized that a high level of instrumentation and control would be required to achieve this. The risk associated with the instrumentation and control systems implemented was to be minimized by using equipment and systems that had been proven in industry while utilizing the most cost effective, state-of-the-art technology available. The reliability of the overall control system was considered to be critical in view of the cost of downtime associated with the gold extraction plant. BRIEF PROCESS DESCRIPTION The dump leaching process treats approximately 1.2 million tons per year of low grade ore at an average grade of 0.035 oz/ton. Run of mine material is dumped on a lined leach pad and weak cyanide solution is applied by drip irrigation. Pregnant solution run off is pumped to carbon columns in the milling plant for gold recovery and the barren solution returned to the dump leach circuit. Average gold recovery is 60%. This process has little instrumentation and control associated with it. The milling operation treats 700,000 tons annually of higher grade ore (0.200 oz/ton initially, dropping to an average of 0.135 oz/ton after first two years). Recovery is directly related to head grade (fixed tail assay effect) and currently averages 96%. A single pass through a jaw crusher reduces run of mine ore to minus 12 inches. The ore is stockpiled and reclaimed by loader for grinding in a two-stage milling circuit consisting of a SAG mill and ball mill, the latter in closed circuit with hydrocyclones. Cyanide and lime are added into the SAG mill to start dissolution of gold as early as possible in the circuit. The ground product leaves the milling circuit at approximately 78% minus 200 mesh and is fed to an unique "double thickener" leaching-recovery circuit. This circuit has been discussed in detail in a paper by J. G. Mansanti et a1 (1). Two thickeners are arranged in counter- current configuration with three leach tanks. Overflow solution from the first thickener is treated by carbon-in-columns (CIC) for gold recovery with 85% of the soluble gold recovered onto this carbon. Underflow slurry from this thickener is pumped to the leach tanks, with a total retention time of 12 hours, and then gravitates to the No. 2 thickener. Overflow solution from the second thickener is used as a wash in the first thickener. Underflow slurry from the second thickener is treated in a carbon-in- pulp (CIP) scavenging circuit to recover the remaining 15% dissolved gold. Gold-loaded carbon from both the dump leach and milling circuits is stripped in batches using the Zadra hot caustic- cyanide elution process. Gold (and silver) is recovered from the hot strip solution by precipitation with zinc dust and the product recovered on Funda pressure filters. The precipitate is retorted to remove any mercury and then smelted into buttons. The buttons (approximately 80% gold, 15% silver) are shipped to an independent refiner in Salt Lake City, Utah, for further treatment.

Jan 1, 1990

By Aarne Visnapuu

Unmodified pneumatic rock drills may have noise levels of 115 to 130 dB at the operator's position. Experimental modifications have been made to a standard drill to suppress the noise from the three main sources: the air exhaust noise, the noise radiated from the drill, and the resonance noise of the steel drill rods. A prototype model developed at the Bureau of Mines, Rolla Metallurgy Research Center, operates at a noise level below 100 dB. A close-fitting case and muffler unit, consisting of a metallic skeleton filled with viscoelastic absorber and having a durable cover, provided both muffling and noise absorption. Damping alloys were used at strategic points in the drill. Drill steel resonance noise was reduced by a constrained-layer treatment on the outside of the drill rod. The singular and combined effects of the treatments are presented in detail.

Jan 1, 1973

By J. Wyn Prior

The seismic refraction technique is probably the most popular geophysical method of bedrock profiling in geotechnical site investigations but is somewhat restricted by the inherent assumptions in the method. This paper describes how Hales' method of profile interpretation is modified to overcome the assumptions of increasing velocity and layer thickness with depth when only first arrival data is available. A further expansion of Hales method enables presentation of refraction data in a form whereby bedrock features, such as changes in velocity, relief and dip in particular, are more readily recognized. Characteristic curves of the more common bedrock features are presented as an aid to bedrock feature recognition.

Jan 1, 1976

By Dennis N. Poffenroth

One concern of the Mine Safety and Health Administration is the structural integrity of steel wire ropes used on mine personnel hoists and elevators. Failure of such ropes has resulted in loss of life and property. Although thorough and regular visual examinations are performed, hoist ropes may still fail from undetected internal wear, corrosion, and broken wires. To complement visual examinations, nondestructive rope inspection techniques have been developed to determine deterioration and removal criteria. The techniques use electromagnetic and permanent-magnet test instruments designed by a Canadian firm. This paper describes the operating principles, field and laboratory testing of these nondestructive testing instruments, and discusses the feasibility of using this type of testing as a supplement to visual examination and destructive tests.

Jan 1, 1982