Search Documents

By J. Hong, K. Han, C. Park, C. Yoon, H. Yoon, N. Kim

The contents of three platinum group metals (PGM-platinum, palladium and rhodium), from the spent automotive catalyst, and two NIST SRM (National Institute of Standard and Technology Standard Reference Material, Used Auto Catalysts) were determined by the X-ray fluorescence (XRF) spectrometry. The XRF technique has been proven to be a fast, effective and accurate method in determining not only PGM but also other solid materials of less soluble for wet digestion analysis. The detection limit of the XRF analysis is better than that of the inductively coupled plasma mass spectrometry which usually requires significant dilution to avoid high dissolved solid concentration. However, the XRF technique suffers from a strong matrix dependent problem. The objective of this study was to examine the applicability of the XRF analysis where the sample matrix was not exactly the same as the standard materials with particular reference to PGM analysis. This study enabled to compare the effect of various matrices including alumina, iron, copper and nickel on determination of the contents of PGM.

Jan 1, 2004

By Robert L. Sundeen, Richard V. Wenberg

INTRODUCTION Shotcrete can be defined as spray-applied concrete with a maximum size aggregate in excess of 9.5 mm (0.375 in.). The concept evolved from guniting, which uses smaller aggregate and generally produces concrete with poorer physical properties. The larger aggregate used in shotcrete requires less water in the mix, while offering larger bonding surfaces, thus imparting greater tensile and compressive strengths. TYPES OF MACHINES Two basic designs of shotcrete machines in general use are the wet or prehydrated zero slump and low slump type, and the dry or nozzle hydrated machines. Fig. 1 shows a typical zero-slump machine in a con¬figuration commonly used for small-volume require¬ments. The prehydrated zero-slump machine mixes exactly proportioned batches in a sealed pressurized chamber. "Slugs" of hydrated shotcrete mix and com¬pressed air are sent through a distribution hose to the nozzle where the wet mix emerges as a spray. The spray is directed onto the rock surface by the nozzle operator. The low-slump machine is similar, except that a thick slurry mix of aggregate is delivered throughout the distribution hose to the nozzle. Fig. 2 shows a typical low-slump shotcrete machine used in moderate-volume applications. The nozzle-hydrated shotcrete machine accepts a premixed "dry" (4 to 6% moisture) batch of aggregate and cement. A constant feed of this mix is directed by compressed air through the distribution hose to the nozzle. At the nozzle, water for hydration is introduced into the emerging spray. The hydrated mixture is di¬rected onto the rock surface by the nozzle operator. Fig. 3 shows a typical dry-mix machine. The major difference between the two basic machine designs is the consistency of the shotcrete quality. Pre¬hydrated machines have high degrees of consistency and produce high-strength concrete, resulting from their ability to produce exact mixtures of zero or low-slump concrete within the machine. Nozzle-hydrated machines tend to produce poorer quality concrete because of the difficulty in controlling the water content at the nozzle. Water input essentially is an art. As such it is not precise, and the shotcrete produced is of variable quality. MATERIALS HANDLING Materials handling presents a problem to either type of shotcrete machine. At times considerable quantities

Jan 1, 1982

By Patricio Vergara Lara, Jorman Barrera

The selection of the production level elevation is one of the most critical strategic decisions faced by large-scale block or panel caving projects. This elevation largely affects project timelines, capital expenditures, resource recovery, and may even constrain the mine’s maximum production capacity. Over the years, many computational tools have been developed to assist in this decision, most of them based on the same principle of maximizing the project value given its production level elevation. However, for large and inclined deposits, or those extending significantly in the vertical dimension and where extraction cannot be achieved from a single level, traditional selection techniques involving multiple production horizons often lead to suboptimal results. This paper proposes a methodology ensuring that the selection of production level elevations in a multiple horizons (“lifts”) case is globally optimized. Input parameters include economic and cost variables, maximum extractable column height, and deepening costs. The methodology is demonstrated through a real case study to illustrate its potential impact on project value.

Feb 22, 2026

By Samuel Frimpong

The preparation of graduate talent for the mining industry is a challenging process, given the multifaceted and complex array of decisions mining engineers make in discharging their responsibilities. As leaders, mining engineers must manage operations, lead project teams, mentor junior engineers, chart the technological directions of companies and deal with several organizations for maintaining the technical and economic feasibility of operations within strategic and tactical framework. Traditionally, the completion of the bachelor of science degree curriculum, with a minimum cumulative grade point average (CGPA), has been used as a graduation measure by Missouri University of Science and Technology (Missouri S&T). Companies have long realized the limitations of the CGPA for recruiting graduates because mining engineering is an applied engineering discipline. Company recruiters have sought to correct the limitations by factoring experience and behaviors into the selection process when recruiting knowledgeable and well-rounded graduates. In this paper, the authors introduce a new metric, which combines the current CGPA (knowledge) with experience and attribute (KEA) metrics to gauge the job readiness of graduating engineers. The KEA metric, also called the job-readiness factor (JRF), is the sum of K (50%), E (30%) and A (20%). The KEA process has been applied to a graduating class in Missouri S&T to demonstrate the value of the new metric system. The results show a fairly positive correlation between CGPA and the KEA metric, with a coefficient of determination of about 70%. Overall, the KEA metric system provides a better picture of the capacity and job readiness of graduates entering the workforce.

Jun 1, 2013

By W. R. Reed, G. J. Joy, B. Kendall, A. Bailey

"Testing of the NIOSH-designed roof bolter canopy air curtain (CAC) has gone through many iterations demonstrating successful dust control performance under controlled conditions. J.H. Fletcher & Co. (Fletcher), an original equipment manufacturer of mining equipment, has further developed the CAC concept by incorporating it into the design of its roof bolting machines. A new CAC design has been developed incorporating the results of testing of the NIOSH design and the recent Fletcher design. Observations from smoke testing conducted on this new CAC design in a laboratory setting show promise for improved performance. INTRODUCTION Exposure to respirable coal mine dust can cause coal workers’ pneumoconiosis (CWP) otherwise known as black lung. If silica is present in the dust, the miner may develop silicosis in addition to CWP. CWP and silicosis are occupational respiratory diseases that are ultimately fatal and have no cure. The only method of prevention is through elimination of exposure to respirable coal mine dust and crystalline silica (quartz). The current occupational exposure limit (on an MRE basis) for respirable coal mine dust is 2.0 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities [30 CFR 70.100 2015]. Recently enacted legislation changes this standard beginning in August 2016 to 1.5 mg/m3 for a full working shift [Federal Register, 2014]. If the respirable coal mine dust contains more than 5% silica, the applicable respirable dust standard is reduced; calculated as 10 divided by the percent quartz present [30 CFR 70.101] so that the effective exposure limit for respirable quartz is 0.1 mg/m3 for a full working shift. Sources of exposure to respirable coal mine dust for the roof bolting occupations include infrequent maintenance and cleaning of the vacuum dust collection system and operating the bolter downwind (in the return air) of the continuous miner [Goodman and Organiscak, 2003]. Recent studies have demonstrated that vacuum dust collection systems are effective in capturing bolter-generated dust, if maintained and operated correctly and if proper face ventilation techniques are used. However, most exposure to respirable coal mine dust for the roof bolter occurs when the roof bolter machine is operated downwind of the continuous miner [Potts et al., 2011; Colinet et al., 2013]. Because of this higher exposure downwind of the continuous miner, the roof bolter is generally limited to working downwind of the miner only once during a production shift"

Jan 1, 2016

By A. P. Gentsch

Commercially mined calcium carbonate is normally found near the surface in the United States. It is nun& either by open pit or underground methods, depending upon its geologic setting. Processing ranges from simple crushing to the more sophisticated ultrafine processes. Intermediate steps are pulverizing, screening, beneficiation, classification, fine and ultrafine grinding, and surface treating. These processes are performed both dry and/or wet resulting in powdered or slurry end products.

Jan 1, 1986

By D. A. Bird

Geochemical models using published thermo-dynamic data and laboratory derived kinetic rate laws allow prediction of post-closure pit lake geochemistry at open pit mining sites. A combination of "forward" and "inverse" modeling techniques can predict the pit lake geochemical evolution from initial infilling to eventual steady state attained decades or centuries after closure. Computer codes have been developed to model chemical reactions such as pyrite dissolution, describe the ground-water flow regime, and provide rock-water ratios. The incorporation of site specific information, such as ultimate pit dimensions, geologic and hydrologic data, acid generating potential (AGP) vs. acid neutralizing potential (ANP), and laboratory derived kinetic rates, allows application of the model to open pit mines at any stage of development.

Jan 1, 1994

By Jack T. Work

Spiraling costs in every segment of the open-pit mining cycle is a fact of life that every operator must reckon with. The introduction of various shock absorbing devices for rotary drilling is one recent innovation that may significantly reduce overall drilling cost, increase drill availability, and lower maintenance requirements. In a recent all-inclusive test in taconite ores, shock absorbers on Bucyrus-Erie BE 60R and Gardner¬Denver GD 120 rotary drills were directly responsible for overall savings of up to $41.06 per hour. What is It? A shock absorber is simply a device installed between the rotary drive head and drill steel that cushions the two. It functions in the same manner as springs and shocks on an automobile. Some benefits associated with use of the tool are readily apparent on a daily basis; other benefits are realized over longer time intervals and through continued use. A properly designed shock absorber will: •protect the drill from severe vi¬brations, improve rock bit performance, allow application of the best weight-on-bit and rotating speed under all drilling conditions, •function effectively over a wide range of applied bit weights, • have a spring rate soft enough to perform its primary function of absorbing both rotary and vertical vibrational forces generated by rough drilling, •be reliable and subject to as little maintenance as possible, •be easy to install and remove, and • be of such an economic benefit so as to offset the added expense of its application. A shock absorbing tool developed by BJ-Hughes Inc. was used in a recent test. The "Smoothdrill" is just one of the products currently available. This unit absorbs both rotary and vertical shock loads and has no mechanical parts so lubrication is unnecessary. A rebuild of the unit consists of removing the worn rubber element and inserting a new element, an operation taking less than one hour. Minimizing Vibrations Severe vibrations on a blasthole drill operating in broken and discontinuous formations have visible effects. These vibrations often cause structural damage when allowed to' continue, resulting in fatigue cracks in the mast and related structural components in the drill. When rough running formations are encountered, drilling must be interrupted and possibly shut down. Usually, the drill operator resumes drilling using less down pressures and various rotational speeds until firmer drilling is encountered. An effective shock absorber can substantially reduce these vibrational forces so more down pressure can be applied in bad ground. It is generally accepted that longitudinal vibrations and cyclic forces are more effectively reduced if a tool is designed to incorporate a relatively "soft" shock absorber. The softness of any shock absorbing tool is best judged by its spring rate-the weight required to produce a given amount of deflection, commonly expressed in units of kg per mm or pounds per inch of deflection. All shock tools use a resilient member such as rubber springs, steel springs, fluid, or gas springs to absorb

Jan 4, 1980

By R. Thornton

Montana Tech is located in the historic mining town of Butte, MT and is adjacent to the Orphan Boy mine. This abandoned underground mine will be the heat source for a down-hole heat exchanger (DHE)/heat pump system. The mine was abandoned in the 1950?s and has since filled with water to within approximately 30 m of the surface. The shaft is composed of a 245 m vertical shaft connected with horizontal crosscut drifts at 60 m and 150 m below the water level that connect to a large stope with approximately 1250 million liters of water at a consistent 75-78°F temperature. The intent is to build this heating system to augment or fully heat a newly built 2,000 m2 building on the Montana Tech campus. As designed the system uses ?off-the-shelf? parts making the basic configuration straightforward with the exception of the DHE?s which need to be placed into the vertical shaft. Because there is little or no examples of placing the heat exchangers in a vertical shaft, the primary focus of this work was to model the heat exchanger placement and configuration in the vertical shaft such that thermal currents develop between the stope and vertical shaft in, via the horizontal crosscut drifts, in order to move the water and thereby provide the required energy. This study includes the modeling of water flow, temperature profiles, and the heat contribution from the surrounding rock walls.

Feb 27, 2013

By S. Frimpong

The cable shovel excavator is used for primary production in many surface mining operations. A major problem in shovel excavation is the variability of material diggability, resulting in varying mechanical energy input and stress loading of shovel dipper-and-tooth assembly across the working bench. This variability has a huge impact on the shovel dipper and tooth assembly in hard formations. In addition, the geometrical constraints within the working environment impose production limitations resulting in low production efficiency and high operating costs. A potential solution to the above problems is the application of an intelligent cable shovel excavation(ICSE) technology. In this paper, dynamic models of the cable shovel excavator are developed with numerical examples. These models form the basis for developing dynamic shovel simulators for an intelligent shovel excavation technology. The dynamic equations are developed using the Newton-Euler techniques. The path trajectories for efficient excavation, dynamic velocity and acceleration profiles, and dimensioned parameters for optimum feed force, torques and momentum of shovel boom-bucket assembly are modeled and used for efficient excavation. The optimum digging forces and resistances for the cable shovel excavator are modeled and used to predict optimum excavation performance.

Jan 1, 2003

By Henry T. Miller

INTRODUCTION The basic purpose of this paper is to suggest procedures and practices to insure that no employee working in a uranium milling operation receives exposure to radioactive, toxic, or other materials or agents that might produce a permanent, deleterious effect upon his physical health and well-being. This program is also designed to insure that each employee can carry out his assigned duties without risk to his health or to that of his fellow workers. The assumptions underlying this program are by necessity, conservative, with emphasis being placed upon prevention rather than correction or reaction to an undesirable situation. The limits specified-either as Threshold Limit Values (TLVs), Maximum Permissible Concentrations (MPCs), or Radiation Protection Guides (RPGs)--represent both standards of best practice and those of law and regulation. The total program is envisioned as a balanced combination of occupational hygiene and radiation monitoring. This includes surveying, air sampling, personnel dosimetry, bioassay, medical surveillance, epidemiology, and training--all backed by a thoroughly tested and evaluated set of emergency procedures. The program, as presented, is keyed to the results of monitoring, surveying, air sampling, medical surveillance, and epidemiology--it being obvious that no problem can result when no hazard can be identified. The lack of an identified hazard, however, does not negate the need for such a program and prudence suggests the need for routine surveillance programs in the best-designed facility. [The Model Mill] The model mill used in this paper is that presented by the U. S. Environmental Protection Agency in its study of the uranium fuel cycle1. The model mill processes 600,000 metric tons of ore per year into 1,140 metric tons of U308 as yellowcake per year using an acid leach process. Other characteristics of the mill such as location, tailings dam design, number of light water reactors supported, and geographical location are not pertinent to this paper. The usual remote western location of these facilities produce some difficulties in delivering the required occupational medical services and is not within the scope of this paper. The operating lifetime of most mills is commonly estimated as from 12 to 15 years in actual practice; however, the U. S. Environmental Protection Agency estimated a 20-year lifetime for its model. The principal steps in the acid leach process include :2 (a) Ore is blended and crushed to pass through a 2.5 cm (one inch) screen. The crushed ore is then wet ground in a rod or ball mill and is transferred as a slurry to leaching tanks. (b) The ore is contacted with sulfuric acid solution and an oxidizing reagent to leach uranium from the ore. The product liquor is pumped to the solvent-extraction circuit while the washed residues (tailings) are sent to the tailings pond or pile. (c) Solvent extraction is used to purify and concentrate the uranium. (d) The uranium is precipitated with ammonia and transferred as a slurry. (e) Thickening and centrifuging are used to separate the uranium concentrate from residual liquids. (f) The concentrate is calcined and pulverized. (g) The concentrate or yellowcake is packaged in 208 liter drums for shipment. This process is illustrated in Figure 1.3

Jan 1, 1981

By M. SIDDARAJU, Rameshwar Sah, Satendra Kumar, Arvind Jaiswal

The study explores a novel process to sinter porous iron ore with improved productivity and quality. The iron ore is pre-processed with calcined lime to temporarily close pores, preventing water absorption during granulation. This enhances reaction kinetics and early slag formation during sintering, resulting in significant improvements in sinter productivity, product yield, and cold strength property.

Feb 28, 2022

By Aline Tatom

This paper presents numerical and experimen¬tal results dealing with the application of ferric ion oxidation of uranium in acidic media. Conclusions are derived from matching numerical results to experimental data taken on one-dimensional laboratory leaches using ore from a South Texas Coastal plain deposit. Since the numerical results can be made quite general, we are able to extract and quantify the effects of oxidant concentration, flow velocity, mass transfer, chemical kinetics, and competitive oxidant consumers (pyrite and molybdenite) on the experimental results. Our results suggest that the leaching of uranium is a mass transfer controlled while that of pyrite is kinetically controlled.

Jan 1, 1981

By P. Rusin

Many oxide silver and molybdenum deposits remain undeveloped because chemical extraction yields poor recoveries or is environ-mentally unacceptable. Bio-reductive leaching of such ore samples at MBX resulted in high recoveries of silver and molybdenum. When baseline 3-day cyanide bottle roll tests were conducted on manganiferous oxide silver ore, 13.7% of the silver was extracted. In contrast, 86% of the silver was microbially solubilized into the organic growth medium by bio-reduction with 99.8% dissolution of manganese. A follow-up cyanide bottle roll test yielded an additional 8.5% silver recovery for a total recovery of 94.5%. Baseline 3-day acid bottle roll tests of the iron oxide molybdenum ore yielded 1.8% moly. However, bio-reduction solubilized 93.3% of the moly into the growth medium. An additional 0.3% moly was recovered during the follow-up acid bottle roll test. Microbial treatment of refractory oxide ores with bio-reductive bacteria resulted in higher recoveries of silver and molybdenum than conventional chemical leaching. The bioleaching process occurred at a near-neutral pH at ambient temperatures. The bacterial solubilization of silver and moly was achieved without the use of cyanide or sulfuric acid.

Jan 1, 1992

By C. Patrick

Project scheduling is a deterministic technique utilizing single estimates of activity durations. In reality, activity durations are stochastic and can be better represented by probability distributions. This paper describes the development and utilization of a project scheduling simulation which combines analytical scheduling with stochastic activity durations. The purpose is to provide a method to analyze the sequencing of mining production processes and predict the effect of any planned changes. The simulation is demonstrated through realistic examples, such as longwall face-to-face transfer sequencing and the effect of varying advance rates on longwall development sections. Statistical data, to make more informed production decisions, are generated in the form of project activity/path criticality and project duration distributions.

Jan 1, 1995

A dedicated tunnel construction version of the Caterpillar 328D LCR compact radius excavator is proving highly productive on the A9 Autoroute construction project near Visp, in Switzerland. It is the first machine of its kind to operate on a Swiss contract and uses a special dedicated front attachment designed and constructed by German Caterpillar dealer Zeppelin. The machine offers a powerful, stable and compact solution for tunneling contractors. A rear overhang of just 305 mm (12 in.) provides a tail swing radius of just 1.9 m (6.2 ft). The 328D LCR is ideal for the restricted working areas within a tunnel construction site. The machine is equipped with the wide tracks from the 330D L conventional crawler excavator, ensuring maximum stability when operating. In addition, the boom mounting has been moved further toward the center of the machine for the tunnel model, creating an increased lift capacity over the front end compared with a standard 325D L. The boom itself features a robust box section construction, with high-strength steels, additional supporting struts and reinforced bearings for maximum durability. All pins have hard-chromium plating for optimum protection against wear. Stick digging force is a powerful 134 kN, with up to 212 kN of bucket digging force available, for maximum penetration in blasted material. The 328D LCR is also equipped with a heavy-duty dozer blade as standard. This ensures outstanding stability when working and providing a useful secondary tool for clearing and leveling within the jobsite. Two 45° tilting mechanisms in the boom construction, allow the boom to be swung to 45° on either side of the machine. So the specially designed attachment linkage provides increased rollback for access to the roof of the tunnel. A Caterpillar CW45S mechanical quick-coupler allows rapid changes between specialist tunneling attachments, standard Caterpillar buckets and a range of Caterpillar work tools. The machine is powered by a Caterpillar C7 diesel engine. This six-cylinder EU Stage IIIA diesel motor [ ] offers 8 percent more power than its predecessor, with 140 kW (190 hp) available at just 1,800 rpm. Caterpillar?s ACERT combustion technology results in lower fuel consumption and reduced exhaust emissions. However, the tunnel machine is also equipped with a diesel particulate filter as standard, to further cut exhaust gases within the tunnel working. The 328D LCR is designed for use in transport tunnels of 6.8 m (22.3 ft) in height. With the tunneling boom in place, the machine has an operating weight of 42,540 kg (93,783 lbs), yet retains a transport height with the tunnel boom of just 3.9 m (12.8 ft). Transport width with 600 mm (23.6 in.) track shoes, is just 3.2 m (10.5 ft). On the A9 tunnel contract, the machine is being used by a consortium of Swiss and Austrian companies working for the canton of Valais? Routes Nationals Construction (RNC) department. The 31.8-km (19.7-mile) A9 Autoroute construction project will connect Sierre in the west and the town of Brig to the east. The tunnel that is bypassing the town of Visp is just one of a number along the mountainous route.

Jan 1, 2009

By James L. Patton

Automation of mining increases the productivity of labor, thereby reducing the unit cost of labor. Such cost constitutes the largest portion of the direct or variable costs of producing coal. Therefore, any increase in productivity directly reduces variable cost. The large investment in mechanical equipment carries with it the burden of increased fixed charges. As the proportion of fixed cost to the total cost increases, the effects on the cost of production changes are amplified. Therefore, equipment must be fully utilized at all times. Averaged fixed costs rise with any decline in production. Such a situation forces coal companies to seek every means of main¬taining full production. Figure I will reflect the story on the relationship of production to cost.

Jan 1, 1962

By R. J. Smith

Tar sand deposits in Utah represent more than 25 billion barrels of in-place bitumen, 96% of the known U.S. reserves. The technological development of a hot water processing strategy for the Canadian tar sands and the commercial Production of synthetic crude oil from this natural resource suggest that similar success may be possible for the utilization of Utah tar sands to provide our country with a new domestic source of synthetic crude oil. In this regard an active research program to develop a hot water processing strategy for Utah tar sands has been sustained at the University of Utah for the past five years. The hot water process for Utah tar sands differs significantly from that used for Canadian, tar sands due to the inherent differences in the respective bitumen viscosities and the nature of the bitumen-sand association. These differences have led to the identification of certain design criteria necessary to achieve satisfactory phase disengagement during digestion. (8,9) Subsequent flotation of the digested tar sand is a subject of current attention and is considered in this contribution for the Asphalt Ridge tar sand deposit. Although contact angle measurements of pure Asphalt Ridge bitumen indicate moderate hydrophobicity, air bubble attachment to the bitumen concentrate taken from a 37 liter flotation cell is not possible. This surprising result suggests that the flotation separation is dependent on air bubble entrapment rather than on attachment due to surface hydrophobicity. The occlusion of air bubbles in the bitumen is apparent from visual examination of the concentrate, especially at lower temperatures. It seems that a bitumen bubble agglomerate forms in the impeller region of the flotation cell, the effective density of which is such to allow the agglomerate to float to the surface. A factorial design of the major operating variables in the flotation separation indicated that the quality of separation was significantly dependent on the flotation temperature and to a lesser extent on the degree of agitation. For a flotation temperature of 77C recovery of 96.7 percent was realized at a grade of 61.0 percent bitumen. The improved separation at higher flotation temperatures was found to be due to the decrease in bitumen viscosity resulting in more effective rejection of coarse sand from the concentrate.

Jan 1, 1980

By O. Tranbarger

In aging tunnels, wall and roof deterioration can eventually result in defects that must be detected and repaired to maintain safe structural conditions. In investigating tunnel defect conditions, a specialized FM radar system was developed with a programmable VHF and UHF operating sweep range for optimizing the penetration and measurement capabilities. The new FM radar technology was tested in two aging brick-lined tunnels in New York City. Test results showed that FM radar signals could penetrate eight courses of water-saturated brick and that the original steel liner outside the tunnel walls was intact.

Jan 1, 1985

By S. Kittel, P. Galleguillos, H. E. Urtubia

The rougher flotation at Escondida consists of 80 cells of 100 m3 each, with injected air. Escondida has developed a system of automatic control of the rougher flotation using video cameras, which have been operating since 1997 for remote monitoring and manual control. Since 1999, an image processing software and a group of rules have allowed implementation of an expert system. To date, the expert system controls the superficial speed of each cell by adjusting the air flow and the froth depth of the flotation bank. Preliminary tests of the expert control on two of the eight rows gave 1.2% higher rougher recovery at a 92% degree of confidence. The proven benefits are already sufficient to move towards a complete plant implementation.

Jan 1, 2001