Search Documents

By C. J. Myers, D. L. McKinnon, A. A. Dasys

In 1988, the National Institute of Occupational Health and Safety (NIOSH) published an information bulletin stating that whole diesel exhaust should be considered a probable carcinogen. Since then, regulations across Canada and the United States (Mine Safety and Health Administration, MSHA) have looked at appropriate exposure limits for underground mine workers. In Canada, an interim standard of 1.5 mg/m3 Respirable Combustible Dust (RCD) has been adopted by some provinces and is being looked at by others. MSHA is considering levels as low as 0.5 mg/m3 soot. Golden Giant, being aware of regulatory developments, decided to look at means of reducing diesel particulate on thier large production machinery. This machinery (LHDs and haulage trucks) is powered by Detroit Diesel 71N Series engines and is used to produce 3000 tonnes of ore/day with a longhole mining technique. Having looked at the various control technologies, it was decided to evaluate the potential of using diesel particulate filters with a copper-based fuel additive for regeneration (the process by which collected particulate is burned off). This paper outlines the control technology used and the results of the field evaluation indicating the benefits to the underground mine worker.

Jan 1, 1993

By SAMUEL A. LOLON, ADITYA JUGANDA, JURGEN F. BRUNE, JR. GREGORY E. BOGIN

Historically, there have been many events of mine fires and explosions recorded in the United States and other countries that have demonstrated the existence of explosive methane-air mixtures, herein referred to as explosive gas zones (EGZs) [1]. The risk of mine explosions can increase if these EGZs migrate out from the gob into the surrounding mine entries — a phenomenon known as gob breathing. A number of 3D computational fluid dynamics (CFD) simulations using various magnitudes and periods of barometric pressure variation have indicated that the EGZ outgassing potentially occurs due to lags in pressure, which are strongly influenced by mine conditions and ventilation systems. Early-warning systems with real-time pressure monitoring and the application of gob ventilation boreholes are recommended to detect and mitigate explosion hazards from gob outgassing.

By Stanley Lefond

The health of the industrial minerals industry appears to be improving year by year. In fact, preliminary information suggests that only three commodities (asbestos, bromine, and sulfur-other) failed to show a production gain in 1984 over 1983. In 1983, 10 commodities failed to post gains and six remained constant. The total value of industrial mineral production in 1984 was $16.7 billion, up $1.4 billion from 1983. Cement, clays, gypsum, and crushed stone production increased. Since these are used in housing and construction, this suggests these industries are moving out of their recent doldrums. Barite and clay production also improved in 1984. Local US barite production, however, still has a long way to go to attain the 1981 high of 2.6 Mt (2.9 million st). Barite imports remain high. But they are not as high as the 1982 importation of 2 Mt (2.3 million st). Bentonite production in 1984 increased 20% in volume and 25% in value over the previous year. This suggests improvement in the drilling industry and an increase in demand for iron ore pelletizing grades. All in all, the industrial mineral industry is alive and well. And it shows signs of great improvement in the next few years. Many thanks to those industrial mineral technical committee members for their assistance in assembling this industrial minerals review: M. F. Dibble, H. W. Allen, G. H. Gallup, S. G. Ampian, D. W. L. Spry, H. G. Fleshman, and L. J. Czel.

Jan 5, 1985

By A. Nivala, S. Ulgiati, M. Canino

Mining and processing of bastnaesite ore, (Ln)CO3F, for lanthanides extraction is investigated in this paper. This series of elements proved to be applicable for a wide range of high-tech uses. In spite of the strategic importance of lanthanides, no LCA and energy analyses of their extraction have ever been published. We perform in this paper a Life Cycle Assessment of the Lanthanide production cycle, based on available database and literature data from Mountain Pass mine (USA) and other worldwide mining and processing sites, most of which in China. We investigated three main steps: mining, milling (including transport, grinding and drying), and flotation (for lanthanide chloride extraction). We do not investigate here the separation of pure oxides from lanthanide chloride, a compound which is also marketed as such. The conventional LCA was integrated by means of energy and emergy evaluations, aimed at investigating respectively the global energy cost and the environmental sustainability of the process. Indicators of material intensity, thermodynamic efficiency, and environmental impact (including LCA and ecological footprint impact categories) are calculated and discussed.

Jan 1, 2005

By William Harrison, Robert H. Trent

GENERAL DESCRIPTION History The most striking feature of mining in the United States has been the infrequent use of longwall systems. This system, which accounts for the majority of coal production in Europe, Japan, and other countries, is only recently growing out of its infancy in the mining of normal coal seams and is still untried in the mining of thick coal seams in the US. Its use in the mining of metal and nonmetal ore bodies has been virtually ig¬nored, except for isolated instances in trona, copper, and uranium. Longwall mining is believed to have originated in Shropshire, England, towards the end of the 17th cen¬tury (Laird, 1973). Although the method used would be considered primitive by today's standards, many of the basic concepts have remained unchanged. Longwall mining of coal in the US was first introduced before the turn of the century, but it never gained acceptance as it did in Europe. Historically, longwalling was a cyclic method where a single cut of coal was removed from the face on the producing shift each day, and the work of building stone packs in the gob and manually moving roof support was completed on the off shifts. Due to the amount of dead work, productivity was extremely low. In Europe, however, longwall methods were required despite the high costs involved, because only by this method could coal under heavy depth be mined with any reasonable degree of recovery. Reserves of coal lying under shallow cover, and therefore minable by room¬and-pillar methods, were long ago inadequate to supply most of Europe's coal requirements. In the US coal min¬ing has historically proceeded laterally with the new mines in virgin areas to replace old mines; in Great Britain, Germany, Japan, and many other countries, mining must proceed downward to greater depths. The depth of cover for most coal operations in the US is shallow, i.e., 61 to 305 m (200 to 1000 ft). This, combined with large reserves, has made room-and-pillar methods almost universally applicable. However, longwall systems were tried around the turn of the century. Whenever used, it was frequently noted that the opera¬tion was under the direction of men with foreign ex¬perience and was tried under ideal conditions. Some of the mines that were using longwall or had tried longwall prior to 1910 were the Radiant mine, CO; Vinton Coal Co., PA; Cambria Steel Co., Johnstown, PA; Grundy County and Spring Valley, IL; and unnamed mines in Washington, West Virginia, Kentucky, Iowa, and Kansas. As late as 1961, there was one circular longwall in operation at Centerville, IA. The first modern-day op¬eration to take advantage of European technology and longwall methods was Kaiser Steel Corp. at its Sunnyside mine near Price, UT. Due to deep cover and extremely poor roof conditions, combined with a need for in¬creased production, Kaiser management decided a new method was required and turned to longwall in 1961. The first longwall consisted of an Anderson Mavor shearer loader, British Jeffrey-Diamond conveying equip¬ment, and Dowty roof supports with a capacity made up of two and three 27-t (30-st) capacity props. After nor¬mal start-up problems, this unit averaged over 454 t (500 st) per shift (White and Palacios, 1976). During and after World War II, technology in hy¬draulics and controls had advanced to the point that self-advancing supports and hydraulic props were being developed. In 1960 only I % of West German produc¬tion was from mechanized longwall faces. This in¬creased to 37% in 1970 and 63% in 1973 (Kohlgruber, 1974). In 1976 there were 246 coal mines operating in the United Kingdom. Although this is only 50% of those operating ten years ago, the production has increased 42%, mainly through improvements in longwall equipment and methods (Hunter, 1976). In France and other European countries, the devel¬opment of longwall mechanization has been similar in seams up to 2.44 m (8 ft) thick. In seams that exceed 9.14 m (30 ft), a variety of longwall caving has been developed for coal seams with dips of 0 to 1.6 rad (0 to 90°). Those with the greatest success will be discussed later. As noted, the development of longwall mining to its present state of the art has mainly taken place since World War II with substantial gains in the last ten years. Mechanized longwall has been the result of several re¬lated major innovations (Jackson, 1975) 1) Development of the flexible armored face con¬veyor which can be installed along the face and moved forward without disassembly. 2) Development of face machines such as single and double drum shearer and coal plows which operate in conjunction with the armored conveyors. 3) Development of self-advancing hydraulic roof supports which now include chocks, chock shields, and shields. 4) Reliance of caving of the immediate roof based on proper planning and development. 5) Use of pneumatic slowing to enable extraction below overbuilt areas. The most recent developments in the mining of coal by longwall in the US include the introduction of shield supports at Kaiser's York Canyon mine in New Mexico, single-entry longwall development at Kaiser's Sunnyside mine, and Mid-Continent's advancing longwall system in Colorado. Metal and nonmetal longwall systems in the US have included the mining of copper at White Pine, MI; uranium in Utah and New Mexico, and trona in Wyoming.

Jan 1, 1982

By H. W. Peirce

Arizona is a sun-belt growth-region where 13 tons of industrial (nonmetallic) minerals is being produced annually per capita. In 19B5, non-fuel mineral production reached $1.532 billion and consisted of metallic ($1.277 billion-84%) and nonmetallic ($253.5 million-16%) earth materials. Sand-and-gravel value was second only to copper. over 90% of the value of nonmetallics is represented by combined sand, gravel, cement, and lime. The remaining less than 10% ($25 million) was attributed mainly to stone, specific volcanic products (cinder, perlite, pumice), gypsum, clays, salt, zeolite, and others. Current interest in industrial-mineral development in Arizona is high, especially in the geologically complex Basin and Range region.

Jan 1, 1988

By GRANT COLLIGAN, BROCK O’KELLEY, Corby Anderson

With the world’s ever-expanding push to expand technological capabilities, the need for specialized materials including rare earth elements has exploded. One source found in the USA is bastnaesite, a rare earth bearing fluorocarbonate mineral, currently mined at the Mountain Pass Mine in California. To increase production, it is essential to optimize existing processes and create new ones to better utilize current resources. Therefore, a US Department of Energy Critical Materials Institute sponsored research program was carried out at the Kroll Institute for Extractive Metallurgy to expand the fundamental understanding of the industrial bastnaesite concentrate leaching system. With the help of prior knowledge, thermodynamic calculations and design of experimentation based lab testing, a novel single-stage hydrochloric leach system was created to optimize the rare earth extraction from bastnaesite. Historically, the existing industrial process has utilized a two-stage leach system involving a high-temperature hydrochloric acid leach with liquid solid separations followed by a caustic crack stage of the leach residues. A series of single-stage leach experiments were run by reacting locked cycle flotation concentrates with hydrochloric acid to test common leaching parameters. The results of these patent pending single-stage tests have shown rare earth recoveries significantly higher than reported recoveries of historic two-stage caustic crack processes, all while decreasing the equipment required and the type and amount of reagents needed.

Jan 31, 2022

By Joseph J. Feiler

Fires in underground coal mines are persistent problems anywhere in the world that coal is mined. Coal fires pose safety and health hazards in the form of mine subsidence, loss of energy reserves, destruction of property and surface improvements, and air pollution. In 1995, the US Bureau of Mines (US-BM), in cooperation with the Colorado Division of Minerals and Geology (CDMG),entered into a contract with Goodson & Associates Inc. (GAI) to design and field test the effectiveness of a new foamed grout technology called ThermoCell. GAI is a Lakewood, CO geotechnical and mining reclamation engineering firm. The company developed ThermoCell to control and extinguish underground coal fires. The viability of the special grout and the technology of application were established during a full-scale field demonstration at the abandoned IHI Coal Mine fire, near Rifle, CO. Following acquisition of additional funding by CDMG in 1999, Goodson returned to the site in April to continue the grouting to fully extinguish the IHI fire.

Jan 1, 2000

By T. M. Yegulalp

A short review of the current practice and recent developments is followed by a description of a newly developed approach for the solution of the optimum ultimate pit limit problem. The new approach utilizes the network modeling of the problem for solution by maximum flow algorithm. The latest developments in the implementation of maximum flow algorithm present significant time and memory savings as compared to initial development due to Ford and Fulkerson. Results of a series of computational tests are presented to demonstrate how this approach performs as compared to the well-known Lerchs Grossman algorithm. It is also shown that the solution by the new method will automatically include several optimal solutions based on predetermined number of benches to be included in the analysis.

Jan 1, 1993

By John A. Reeves

The Coal Creek Preparation Plant is the coal cleaning facility of Mid-Continent Coal and Coke Company. Located three miles west of Redstone, Colorado, and at an elevation of 8,040 feet the preparation plant cleans coal produced at the company's Dutch Creek Mine and L. S. Wood Mine. (See Fig.1.) Current production is at the rate of 2500 tons per day clean coal. Plant capacity is rated 350 TPH raw coal. Reject rates vary with mining conditions from 8% to 25%. Factors which influenced the design of the coal cleaning facility were the characteristics of the coal, the location in a tourist oriented resort area, and the extreme winters of the area. Lack of areas suitable for settling ponds and the necessity of keeping effluent waters out of the fishing streams dictated a closed circuit plant. Severe winter conditions, which last six to seven months out of the year and temperatures which have dropped to 40° F. below zero on occasions demanded that the plant be totally insulated and enclosed indoors.

Jan 1, 1967

By Ihsan Berk Tulu, Gaobo Zhao, Deniz Tuncay, Syd S. Peng

Longwall mine instrumentation for measuring abutment stress distribution, mining induced immediate roof stress change and deformation, and primary/secondary support loads and deformations provides critical guidance for the design of gateroad chain pillars and roof support. Field measurement results are also recognized as the best way to calibrate numerical models that have been used to study the failure and support mechanisms. International Conference on Ground Control in Mining (ICGCM) started in 1981 and since then, there were 26 papers published in the proceedings discussing the stress and load measurements as the face advanced using various field instrumentation techniques. The focus of this paper is on summarizing the analyses of the data published in these papers. Stress/load change monitoring included the following categories: gateroad chain pillar, abutment pressure, bolt load, and pre-driven recovery room. The data shows that the magnitude of stress changes as the face advances varies considerably from panel to panel and mine to mine. However, regardless of types of stress changes, pillar stress, abutment pressure, and bolt load, there exists a rough trend of stress increase as the face advances, generally consisting of three stages, i.e., stress/load (1) initially increases steady or slowly, (2) increases rapidly, and (3) increases reaching the peaks and dropping down slowly or sharply. The stress/load increases start earlier during the second panel mining and are larger than the first panel mining. This review makes it easy for the interested persons to find valuable data for other similar projects.

By A. Wright

Gold Fields Mining Corporation is presently evaluating gold mineralization beneath thick, wet alluvium at the Chimney Creek Project, Nevada. Contamination of reverse circulation samples has been visually apparent since drilling began in the area. Tests have shown that, while contamination can affect assays, reverse circulation holes appear to define mineralized zones almost as well as the diamond drill holes. To improve reverse circulation sample integrity several techniques were tried including a stiff-mud injection system but with limited success. Diamond core drilling continues to be used in conjunction with reverse circulation drilling to further delineate the mineralization.

Jan 1, 1991

By T. J. DeMull

AMAX's Sleeper Mine uses conventional cyanidation milling and heap leaching techniques to produce gold. Since milling operations commenced in March 1986, average ore processing rates have improved from the design rate of 455 tonnes per day to more than 720 tonnes per day. Heap leaching was added to the process facilities in September 1986 at a design rate of 1,500 tonnes per day, and current heap leaching rates exceed 2,680 tonnes per day. Presented are descriptions of the Sleeper processing facilities with emphasis on the crushing and grinding circuits, a review of the selection of crushing and grinding equipment, and a summary of operating performance during the first 16 months of operations.

Jan 1, 1988

By O. Kangal

Flame retardant materials can be incorporated or applied to products, including plastics and textiles, to increase their resistance to fire. Incorporating a flame retardant in combustible materials and plastics is a common procedure to reduce the risk of fires. Flame retardant applications include interior and exterior woods, structural steel columns, fabrics, open and closed cell foam, pressure treated wood, Formica and all types of fabrics for use in commercial applications as well as residential applications where their fire protection products can save lives and valuables. Huntite and hydromagnesite are amongst the most important flame retardant additives materials. Although various areas of the world have potential huntite and hydromagnesite deposits, their place in industry is not well known, and a detailed field search for their deposits has not yet been conducted. They are active during the starting phase of a fire, in that they prevent the spread of an inner or exterior source of ignition to the flame-retarded material, thereby, preventing, delaying or inhibiting the spread of a fire. Flame-retardants are, therefore, just one element among many in a concept for preventive fire safety. To obtain huntite and hydromagnesite concentrates that are more than 95% pure, which are used in flame retardant industry, flotation tests were conducted on low-quality huntite and hydromagnesite ores.

Jan 1, 2009

By John S. Timmons, Eivind B. Jensen

The Henderson mine is an underground panel-caving molybdenum mine located in the mountains of central Colorado. All development and primary production operations are performed using diesel-powered, rubber-tired mobile equipment. The growth in manpower and equipment was rapid in the five years following the July 1976 start-up, reaching about 250 machines and 2000 people to produce 9 Mt/a (10 million stpy) of ore. However, due to dramatic improvements in productivity, production is currently at a rate of 8.1 Mt/a (9 million stpy) with about 570 people and a much smaller equipment fleet. The mine's high degree of mechanization and accompanying maintenance costs have focused increased attention on the maintenance function as a cost center with potential for improvement. To realize some of that potential, several approaches to equipment maintenance have been adopted. None of these stand alone effectively, though, and their success relies on their working together in the overall program. The approaches that characterize the equipment mainte¬nance philosophy at Henderson are described here. Preventive maintenance The value of preventive maintenance as an alternative to breakdown or emergency repair is widely accepted in industry. When production began in 1976, few people at Henderson had experience maintaining diesel-powered, rubber-tired equipment. Other company operations such as its previous Urad operation and the Climax molybdenum mine near Leadville, CO used rail and Blusher technology. A maintenance consultant was hired to establish a formal preventive mainte¬nance program. The initial program contained four different preventive maintenance services, "A," "B," "C," and "D." Each was keyed to a different operating interval. • "A" service was the most frequent. It was a quick, general inspection and greasing of all fittings. •"B" service added a more detailed inspection. • "C" service included changing all filters and most fluids, such as engine oil. • "D" service was originally designed as a comprehensive inspection and testing of major component systems over a period of 24 hours during which the equipment was removed from operation. It was believed that most problems uncovered by the inspection could be reported and scheduled for repair at some later date, with only critical repairs being done during the service. In addition to these scheduled preventive maintenance services, a schedlle of minor and major rebuilds at intervals of 2500 to 5000 hours was established.

Jan 1, 1989

By J. A. Haggman

In a country richly endowed in mineral wealth, Climax Arimco Mining Corporation's (CAMC) Dinkidi porphyry Au?Cu deposit in Nueva Vizcaya province, Philippines, represents the most significant mineral discovery in the country in recent times. The deposit is located within a belt of young intrusive and volcanic rocks in the Sierra Madre mountain chain of north Luzon a region previously unassociated with porphyry-style mineralization. Since 1989, drilling of the Dinkidi deposit has outlined a resource of 124 million tonnes of 1.0 g/t gold and 0.41 % copper. Regional exploration throughout CAMC's 37,000 hectare FTAA has identified a further sixteen potential porphyry-related deposits. A new mining law was passed in March 1995 but prior to that CAMC had the first Financial and Technical Assistance Agreement (FTAA) granted by the Philippine government allowing 100% foreign ownership of mining projects.

Jan 1, 1997

By Hamid Maleki

Rock mechanics models are “data-limited,” i.e., one seldom knows enough about a rock mass to use computational models unambiguously. Statistical methods, however, are capable of being applied where there are good data but a limited understanding of certain natural phenomena, such as the creep of rock salt or elevated risk domains associated with violent failure of strata commonly referred to as coal bumps and coal bursts. Important to these evaluations are (1) having statistically valid data collected consistently and (2) incorporation of analytical calculations for quantifying geologic, mining and particularly geotechnical variables. By combining the strength of the statistical and analytical models, an improved “hybrid” model is created and utilized. To demonstrate the use of hybrid statistical-analytical techniques in rock mechanics problems, three case studies are used. The first case study involves a historic examination of a nuclear waste repository in rock salt, where mathematical models are built using excavation con- vergence data to identify significant variables and estimate future deformation and stability. This case study uses the convergence rate at up to 121 locations of different ages and geometries using monitoring data over the facilities' footprint excavated through 1998. The second case study focuses on ongoing analysis of coal burst mechanics and associated factors. Within the last three decades, a hybrid statistical-analytical methodology has been applied for identifying significant factors affecting coal bursts. This final hybrid model utilizes data from 30 case studies from Utah, Colorado, Kentucky, and other Eastern U.S. mines providing predictive capability for the entire United States coal fields. The last case study is the assessment of Castlegate Sandstone escarpment stability using historic data collected over 17,000-ft of sandstone escarpment exposure in the vicinity of longwall operations in Utah. Results from all three case studies are used for demonstrating the utility of the method in solving ground control problems.

Jun 25, 2024

By R. H. King

This paper describes the results of an underground coal mine trial installation of a shielded trailing cable. The cable was a three conductor, round, type SHC-GC, and was installed on a shuttle car in a conventional room and pillar mining section. The purpose of presenting the information is to prepare mine operators for proposed legislation that will require shielding on low-voltage trailing cables. Specifically, machine modifications are required to cable reels, packing glands, and couplers. Cable splicing is not as complex as expected but additional materials are needed in the kit and splice training is necessary. Even though shielding will cause some problems for the mine operator, it can reduce the hazard of electrical shock to mine workers. This paper will present information that mine operators can use to solve most of the problems that will be encountered if they are required to install shielded cables. The in-mine evaluation was funded by the U.S. Bureau of Mines.

Jan 1, 1980

By H. B. Trinh, R. R. Srivastava

"Spent auto-catalyst is a potential secondary resource because of the higher concentration of valuable platinum group metals (PGMs) as compared to the primary ores. Despite the well-developed commercially tenable technologies, further researches are being carried out to extract the PGMs with high efficiency. It is however, critical in this context to reuse not only the PGMs but also other metals contained in the spent auto-catalyst particularly that of the cordierite substrate such as aluminum, magnesium and cerium oxide (CeO2). This is important in view of the fact that no recycling process has ever stressed upon the recovery of cordierite substrate and CeO2 since the main target metals are mostly the PGMs. In this study, a new hydrometallurgical approach has been proposed in order to recover the PGMs as well as cerium oxide and materials from the cordierite substrate by using sodium hydroxide roasting followed by sulfuric acid dissolution. Under the optimal conditions for roasting at above 600°C, and weight ratio of sample to NaOH of 1:1 for 60 min, the cordierite was converted to the soluble phases. Dissolution of the roasting products using H2SO4 solution (1M) at 25°C for 60 min enriched the PGMs and Cerium oxide contents in the residue. Subsequently, PGMs in solution after dissolution can be cemented using Al and Cerium oxide in residue can be recovered by hot digestion using concentrated H2SO4.. INTRODUCTION Auto-catalyst can significantly control the gaseous emission of automobiles, and has been considered as a potential secondary source of Platinum group metals (PGMs) after being decommissioned from the vehicles. The PGMs demand is continuously increasing to comply with the growing vehicle population and the tightening of emission standards all over the world; meanwhile the natural resources of these metals is facing the threat of depletion. Therefore, it is crucial to progressively substitute with an alternate resource to supply PGMs other than that of the primary ores. Nowadays, vehicular transportations worldwide are totally installed with the auto-catalysts. However, they should be replaced after reaching their service life. If there is no recycling of such resources, huge amount of valuable metals will be wasted. The quantity of PGMs that can be recovered from the spent auto-catalyst depends on the size of car, which averages to 1-2 grams for small cars and 12-15 grams for the big truck; this is significantly higher than that of the primary ores containing 2-10 grams PGMs per ton. Consequently, the recovery of PGMs from spent auto-catalyst becomes extremely favorable as compared to the primary resources due to higher concentration of PGMs, with much lower and simpler processing steps, and lesser pollution."

Jan 1, 2018

By T. BACHMANN, G. SHAPLAND, E. Amini, N. BEATON, M. BECERRA

In this study, several methodologies to manage low grade and often competent portion of the ore have been proposed and tested in lab, pilot and operational scales. Relevant to this subject, the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE) has developed Grade Engineering® (GE) concept to modify feed streams by rejecting the low grade and possibly hard components in the stream at the early stages of a value chain. Application of GE requires to understand the impact of the process on the value chain as they are value modifiers on in situ opportunities. Traditional modelling approaches and tools do not have the ability to run the analysis in a block model scale with high fidelity in an integrated value chain. Integrated Extraction Simulator (IES) in conjunction with sophisticated analytical tools such as a neural network (NN) was used to develop and reconcile a fully integrated value chain. The value chain model makes it possible to run all available blocks in the Geomet block model, which could be several millions, under possible scenarios for Grade Engineering for economic evaluation analysis and mine planning.

Sep 16, 2020