Search Documents

By W. R. Dengler, R. S. Brown

In 1974, Brunswick Mining and Smelting Corporation Limited started a 48 million dollar expansion programme at their property in Bathurst, New Brunswick. A portion of the expansion plans includes a 26 foot diameter 4,525 foot deep shaft, underground crusher and conveyor excavations and lower level access development. J. S. Redpath Limited was awarded the contract for the new shaft and associated rock work in May 1974. Brunswick Mining and Smelting Corporation Limited, a member of the Noranda Group, operate this 10,000 ton per day lead, zinc, copper plant with proven reserves in excess of 90 million tons. While most of the ore is provided by the underground operation at the Number 12 ore body, some tonnage is produced from the open pit at the Number 6 ore body. Long range plans indicate a phasing out of the open pit and an increase in production from the underground operation. Existing facilities at the underground mine could not provide additional tonnage, thus the requirement for a new shaft. (Figure 1) The new shaft will also provide access to ore below the 2,800 level which is currently the bottom level of the existing facility. The contract called for sinking a 26 foot inside diameter, nine compartment concrete shaft 4,525 feet deep (Figure 2). Station access and ramp development from existing workings would be required to the bottom of the new shaft. In addition, development work for new crushing and conveying facilities was needed simultaneous with the shaft sinking.

Jan 1, 1976

By A. S. Murphy, E. V. Manlapig, C. Green, J. W. Parkinson

Historically in Australia and the United States many coal mines deposited raw wash plant fines into large slurry impoundments. At the time the technology and market economics did not exist to make it viable to recover coal from these tailings. Today better technology exist to dredge and clean the tailings and there are circumstances where government regulations and market forces have come together to make coal recovery from these old tailings impoundments economically viable. This paper discusses the processes and equipment being used in tailings impoundment reclamation operations in Australia and the United States, and discusses the economic forces driving these operations.

Jan 1, 2001

By Jim Finley, Adam Bedell, Eric Schrader

The CSO 52 Storage Tunnel and Pump Station project consists of 4,700 ft of hard rock tunnel, 2 intakes, and a 4 MGD wet pit pump station. During the geotechnical investigation, it was determined that the host geology contained abundant suldes. The purpose of this paper is to detail the investigation and subsequent determination that acid producing materials would affect the project during construction as well as long-term exposure of tunnel lining and permanent components during the operational life cycle of the tunnel and pump station. Details regarding the interaction between tunnel components and the acid producing material are also provided.

Jun 23, 2024

By Warren C. Gerler

An overland belt conveyor system is installed for only one reason to save money. It must pay its way on a ton-mile basis over a stated period of time, and do so in competition with other forms of transportation. Such a system with its economies has recently been installed at Simco-Peabody's mine near Coshocton, Ohio by Link-Belt Company. Three miles in length, this system carries coal from open pit and underground mining facilities to the Conesville Power Plant of Columbus & Southern Ohio Electric Company. The coal was formerly trucked from the mine direct to the power plant; but over the years the mining operations have moved progressively farther and farther from the plant, making the over-the-road hauling distance correspondingly greater. Simco-Peabody has mining operations over a considerable area just east of the Conesville Station. The majority of the coal is recovered by conventional strip mining. Some underground mining` is performed by the high wall method.

Jan 1, 1963

By Betty L. Gibbs

A short course, held during the SME Annual Meeting in Phoenix, AZ in February, focused on software for surface and underground mine modeling. The objectives of the short course were to review techniques for surface and underground mine planning. Mine planning software vendors were invited to demonstrate how their software runs, given a standard data set. Six vendors of mining-specific software participated in the workshop. They were Exploration Computer Services (MINEX 3D), GEMCOM Services, Inc. (PC-MINE), KJRA Systems (VULCAN), Mine Development Associates (SURPAC), Micromine and MINEsoft (TECHBASE). Data set A data set was created to challenge the capabilities of each vendor's software. The criteria used for the data set selection were: • a minimum of 300 drill holes; • the data must include topography, drill hole survey, assay and formation contacts; • the deposit was multimetallic; and • there was the potential to be mined by surface and underground methods. The data set used was an actual, complex copper ore body with a small amount of gold. The ore body was close enough to the surface to be mined by surface techniques. Part of it, though, was also amenable to underground mining. To further complicate the problem, a river ran across the area of the ore body. This presented mine planners with the problem of either moving the river or mining around or below it. The ore body had not been mined, so no data was available for the tons and grade actually produced. Data for the mine planning problem was distributed to each vendor about two months before the short course. They had the opportunity to load the data into their systems, build an ore body model and perform preliminary work. During the first day of the workshop, the vendors received problems concerning the ore body. They went to work on their machines, attempting to show short course participants how their software could help solve the problem.

Jan 1, 1992

By Bradford F. Townsend, Colin R. Speers

INTRODUCTION This is the first in a series of papers addressing practical tunnel lining design. The format for this and future papers is to present a particular topic and support the presentation of the guidelines by the practical application of a case history. The primary intent is to provide guidelines for the geotechnical and structural design of tunnels where the tunnel size and/or ground conditions dictates that systematic support of the excavation is required following each increment of excavation. This method of tunneling is commonly referred to as Sequential Excavation and Support(SES) and is also commonly termed the New Austrian Tunneling Method (NATM) The authors developed the design guidelines from experience gained over the past two decades during the design and construction of several major railway, highway and water-transfer tunnel projects in Africa and Asia. During this time it has been possible to compare the performance of the as-constructed structures to the predicted performance as given by the design process. Excavation was typically carried out in widely varying ground conditions (weak-bedded rock, jointed hard rock, and soil-like poorly cemented rock with groundwater). It is therefore intended that the design guidelines could be applied, in general terms at least, to any tunnel excavated in any ground mass condition with any ground material type (hard rock, soft rock, bedded rock, soft ground, and soil) with or without ground water. This first paper is an introductory paper that defines the scope and a brief outline of the design issues that may be presented in detail in later papers. What is design? It may be thought of as any rational/verifiable/justifiable process whereby a concept is transformed into information that can be used to bring the concept to reality. In the case of a civil structure, design may be defined as that process, which is documented and can be audited, that determines information such as the shape (form) of the structure, the dimensions (size) of the structure, the thickness and strength of structural members that comprise the structure, etc. This information can be used to compute the time, money and resources required for

Jan 1, 2005

By T. McKeon

Gravity separators are commonly used in multistage cleaning and scavenging circuits to improve the quality and/or recovery of the final concentrate. Unfortunately, studies suggest that many industrial plants are poorly designed in terms of equipment layout. This shortcoming can often be attributed to a failure by engineers to make use of fundamental process engineering tools for circuit design. One of the most important of these is linear circuit analysis. This powerful tool makes it possible to mathematically compare the relative efficiencies of circuit configurations in advance of experimental testing. This article provides a basic review of the linear circuit analysis concept and discusses some of the key insights it provides for the layout of multistage circuits. An industrial case study is provided to show the tremendous impact that this process engineering tool can have on the design of multistage spiral circuits in a heavy mineral wet plant.

Jan 1, 2005

By D. U. Gustafsson

After half a million meters drilled with Wassara we are now confident that ITH hammers powered with simple water will become an established product for production drilling. Today four drill rigs in LKAB Malmberget equipped with Wassara drill about 25 000 m per month of 4 1/2" holes. In Kidd Creek, Canada, Was sara is used for production drilling in stopes with good results. The first Wassara 6" hammer has drilled a 36 meter long, completely straight horizontal cut hole for drifting in the LKAB Malmberget Mine. Main advantages are about doubled penetration rate, very good air quality and improved hole cleaning which facilitates stabilized drilling. Disadvantages are resistance to new technology and, in some cases, the increased use of water.

Jan 1, 1995

By William R. Yernberg

The 2002 Arizona Conference was held Dec. 8 and 9, 2002, at the Doubletree Hotel at Reid Park in Tucson. The annual conference is organized by the Arizona Conference Board of Directors, which represents SME sections in Arizona and adjacent areas. The conference provides an opportunity for individuals and corporations associated with mining in the region to get together once each year to discuss the status of the industry. The meeting featured a keynote address, a distinguished lecture and about 30 technical papers. As was the case at the 2001 meeting, the economy, the price of copper and foreign competition continue to be the hot topics of discussion among the attendees. The domestic copper industry still faces challenges due to low copper prices dictated by the world market and because of a weakened domestic economy. There continues to be concern about the Arizona region’s copper industry in light of the mergers, downsizing and shutdowns that have occurred during the past several years.

Jan 1, 2003

The stability of mine roofs in permafrost zones is determined mainly by temperature and ice content. The deformation resulting from creep and temperature dependent physical properties of frozen rockmass is the dominant component of total deformation. Roof bolts can consolidate the roof and control its deformation. In this paper, a finite element model for analysis of the effects of roof bolting in a frozen rockmass is presented. The model includes the variables normally encountered when analyzing the effects of roof bolting in rocks. It also accounts for properties unique to frozen rockmass, creep deformation and the change in Young's modulus with changing temperature. The model shows that, as bolt spacing decreases, there is a trade-off between increased roof stability from increased mechanical support and decreased stability from increased conduction of heat into the frozen roof. This result was expected, and shows that, for a given set of rockmass conditions, including ice content, temperature, particle size, etc., there is an optimum bolt length and bolt density for minimum roof deflection.

Jan 1, 1996

By Goran Mathisson

In several investigations the correlation has been studied between the fuel consumption and the reducibility of the charged material in the zone of indirect reduction in the blast furnace (1, 2, 3, 4, 5). It has been found that increased reducibility allows greater gas utilization which accordingly lowers the fuel consumption. In direct reduction units this relation has not yet been fully established partly owing to the lack of accurate test methods and experience with different materials as regards reducibility. However, since the production rate in a direct reduction unit is closely related to the time required to reach high degrees of reduction, the reducibility must be regarded as one of the most important properties of the material.

Jan 1, 1979

By J. C. Stankus, R. Ochsner, B. Hanson

"Bull Mountains No. 1 mine of Signal Peak Energy made another success in its 4 Right pre-developed recovery entry on March 23 and 24, 2015, after the first successful cut-through and shield retrieval of 3 Right pre-developed longwall recovery entry in 2014[1]. Under the same geological conditions, the major difference of 4 Right and 3 Right is the 600 psi Unconfined Compressive Strength (UCS) value of light-weight concrete in 4 Right versus 800 psi in 3 Right. In addition, one more recovery chute was added in 4 Right. The unique geological conditions in this mine include: (1) the low overburden of approximately 200-260 ft, (2) prevalence of roof joints parallel to the face in the sandstone/siltstone dominated overburden, (3) proximity of the Rehder rider seam to the bench Mammoth coal seam, and (4) prompt surface subsidence with the face advancement. The 4 Right recovery entry was 42 ft wide and developed in two stages, 20 ft wide in the inby Phase I, and 22 ft wide in the outby Phase II. The entry roof was reinforced with steel wire mesh/non-metallic recovery mesh, primary bolts, and high-capacity supplemental SUMO cables. After all the support was installed, the entry was completely backfilled with specially designed, cuttable, low-density cement. It took approximately half time to easily cut through the concrete with less dust in 4 Right as compared to the concrete-cut-through time in the 3 Right. The updated study further explored the nature and mechanism of effective roof control approaches in the pre-developed recovery entry of this unique geology mine, aiming at providing the safest working environment for protecting the miners. GEOLOGICAL AND MINING CONDITIONS OF THE RECOVERY ENTRIES Bull Mountains No. 1 mine is located 30 miles north of Billings, Montana, and currently mines bituminous coal from the Mammoth coal seam. The mine employed a conventional recovery face in Panel #1 and pre-developed recovery entries in Panels #2, #3, and #4 (Figure 1). The typical mining and geological conditions are as follows:Overburden Depth The overburden above the Mammoth coal seam in the #1-#4 Right recovery areas is approximately 200-260 ft. This low cover, in combination with specific roof geological features (especially the prevalent roof joints and proximity of rider seam), constitute unique ground movement characteristics when the longwall face advances into the recovery entry if no sufficient roof support is installed."

Jan 1, 2016

By Qingqing Huang, Aaron Noble

The Mineral & Metallurgical Processing Division (MPD) of the Society for Mining, Metallurgy & Exploration held the first MPD Student Video Contest during the spring of 2021. The event showcased the work of 18 graduate and undergraduate students from several U.S. and international institutions. The contest began in January when students submitted a onepage abstract for judging. Over the next several months, they developed a three-minute video that further explained their research findings. Both the abstract and video were evaluated by a panel of judges, and the top-placing participant was recognized at an MPD virtual event held on June 10.

Sep 13, 2021

By N. Merriam

This report describes Koppelman's work to develop the K-Fuel® Series C Process used to dry and stabilize Powder River Basin coal. It also contains summaries of the results of bench-scale and pilot plant tests conducted to prove the Series C Process. The process is being used by the KFx-Thermo Ecotek partnership for a 500,000 ton per year commercial plant that has been constructed near Gillette, Wyoming. The plant is presently undergoing shakedown.

Jan 1, 1997

Where space is limited, as it is throughout most of the northeastern United States, new construction either takes place high above street level, or below it. In Lower Manhattan, NY both kinds of expansion can be found in abundance. That is good news for the nearly 200 attendees at the George A. Fox Conference, presented by the Underground Construction Association (UCA) of SME at the Graduate Center, City University of New York, on Jan. 30. Among the many projects taking place in Lower Manhattan?s massive trans-formation process, are expansions to the city?s vast underground network of subways and other tunnels. ?New Yorkers either live on the ground or below it,? said keynote speaker Charles J. Maikish while explaining how an attempt to build above street level walkways never caught on in the city. Maikish is the executive director of the Lower Manhattan Construction Command Center. His job is to oversee the $22 billion project that will transform the island by 2010. From the construction of Freedom Tower at the site of the fallen World Trade Center buildings, to the expansion of the Second Avenue Subway, the extension of the East Side Access, No. 7 line, the new trans-Hudson line and numerous waterway tunnel expansions, including City Water Tunnel No. 3, the task Maikish is charged with is a huge one. He is primarily responsible for coordinating the scheduling and staging of the overall rebuilding plan, along with the day-to-day coordination of construction work down-town. He places particular focus on mitigating impacts on the environment and mobility, maintaining and improving access and alleviating congestion of any kind related to construction. At the time of the Fox Conference, there were 59 projects under way in Manhattan. All of those projects need things like concrete and steel delivered to sites in very tight working environments. And some need the equipment in even tighter spaces. ?This is not just about the recovery of Lower Manhat-tan (from the 2001 terrorist attacks) but this is a plan to restore it and to maintain its integrity,? said Maikish. ?I think that is the appropriate response to the terrorist attacks.? When Freedom Tower is completed, it will stand 541 m (1,776 ft) about the skyline. That will be a strong statement to the world about America?s strength. But it is the work that takes place much lower that was of interest to the conference attendees. On this respect, Maikish said Manhattan?s efforts below ground aim to provide relief to the city?s street level congestion and to make sure Manhattan ? already essential to the economy of the United States and the world ? stays current by upgrading the existing telecommunications and technological network while also allowing room for growth in that area.

Jan 1, 2007

By H. K. Lin

Cyclic voltammetric and potential step chronoam-perometric techniques were used to study gold dissolution in cyanide solution. Three distinct anodic and one cathodic peaks appear on the voltammogram between -0.50 and 0.80 V vs SCE. The corresponding reactions were proposed to explain the peaks and the passivations. The proposed reactions were in agreement with the effect of pH, cyanide concentration and the rotating speed of the electrode on the magnitude of the peak currents. Cyclic voltammetric tests, with various vertex potentials, were also conducted to examine the proposed reactions. Steady-state currents at various potentials were obtained by potential step chronoamperometric technique and were compared with transient currents obtained by the cyclic voltammetric technique.

Jan 1, 2000

By K. J. Shelswell

This work describes the design, analysis, and comparison of discrete simulation and static spreadsheet models developed to compare the oreflow efficiency of two conveyor-based material handling systems; one approach with a conveyor stream in series and one with parallel conveyor streams. Analysis and comparison indicated that daily rates were significantly affected by random conveyor failures in both designs. The compound effect of random failures limited the effectiveness of long belt assemblies in series, while the parallel conveyor stream design partially alleviated this constraint. The static spreadsheet model predicted a lower average daily oreflow rate for the series conveyor stream design and a higher average daily oreflow rate for the design with parallel conveyor streams when compared to the discrete simulation results. These discrepancies were the product of model sensitivity to operational factors incorporated in the system and provided the opportunity to further use the discrete simulation models for trade-off comparisons and sensitivity breakdowns of mine operating practices and material handling system efficiencies in both the series and parallel belt stream designs

Feb 23, 2014

By L. M. Litz

The results of a study are presented in which gaseous oxygen was dissolved in the leach liquor at concentrations of the order of 300 parts per million. This oxygen-containing solution was injected into portions of a field being operated on a commercial basis with hydrogen peroxide as the oxidant. Comparative results indicate that were concentrations and production rates were essentially equivalent with these two oxidants.

Jan 1, 1980

By H. Huang, R. N. Gow

"EH-pH diagrams are useful tools in understanding how mineral surfaces react in solution and particularly how aqueous conditions can be changed to enhance mineral leaching processes. Successful application of these diagrams, however, requires that several considerations be kept in mind to prevent what had been termed as “gross errors” in their calculation and use. In this paper, the aqueous Cu-S system is used as the basis for explaining the mass-balanced method of calculating EH-pH diagrams with the STABCAL thermodynamic equilibrium software. A breakdown of the Gibbs’ Phase Rule and how it is used in STABCAL to modify the diagrams is included. The methodology was applied to the aqueous Cu-As-S system, and resulting diagrams were compared against examples of those generated using the predominant-ion method. The complexity of such diagrams increases with every additional component, and competition between species becomes more apparent, as can be seen by curvature in the resulting mass-balanced diagrams. The complete diagram for enargite (Cu3AsS4) is shown. It compares well with spectroelectrochemical measurements from Raman spectroscopy and cyclic voltammetry studies.IntroductionInnovation in the field of processing arsenicbearing copper ores has been of particular interest. Copper arsenic sulfosalt minerals such as enargite (Cu3AsS4) and tennanite (Cu12As4S13) are now frequently prevalent in ore bodies as the oxide and easily leachable sulfides become harder to find. These minerals, unless pretreated somehow, concentrate in copper sulfide flotation processes, in turn concentrating the arsenic levels. Increasing environmental restrictions on arsenic content for smelters makes the hydrometallurgical processing of these concentrates more favorable. While enargite is considered one of the more refractory copper sulfides, more so than chalcopyrite (CuFeS2), there are still several methods, both industrially proven and in development, that are capable of processing these ore types. Alkaline sulfide leaching can be used as a pretreatment method to solubilize arsenic selectively (Delfini et al., 2003; Anderson and Twidwell, 2008; Tongamp, Takasaki and Shibayama, 2010a, 2010b), or the entire metal content can be leached using acid-type leaches such as acidified ferric sulfate (Dutrizac, 1981; Hackl et al., 1995; Klauber, 2008), or the chloride assisted, CESL (McDonald and Muir, 2007) or nitrogen species catalyzed (Anderson, 2003) processes can be used.As development of these leaching technologies proceed, it is also important to develop an understanding of the mineral thermodynamics. To date, there are numerous studies on the Cu-Fe-S-H2O system, particularly as it relates to chalcopyrite leaching, yet few studies have done on the Cu-As-S-H2O system. Computer-generated EH-pH diagrams have been employed to illustrate the importance of thermodynamic calculations in providing insight into such a system."

Jan 1, 2016

By David K. Sitler

Continuing advances in manufactured diamond materials used in rock cutting tools have created a new generation of high production tools for mining. This paper will review the three major manufactured diamond products available for the mining industry as supplied by General Electric Company, Specialty Materials Department, and examine the ways in which these materials are employed. As an integral part of this examination, the economic impact of manufactured diamond tools will be evaluated. Time and again, one will find that the premium price of these tools is economically justified when compared to traditional tools.

Jan 1, 1985