Search Documents

By R. C. Freas

The physical and chemical properties of mica are unique relative to most other industrial minerals. As such, mica is suitable for a variety of functional applications in new and emerging markets. This paper examines some of these applications and particularly the contribution mica makes in end product performance.

Jan 1, 1997

By M. Sears, K. Mohamed, J. Addis, J. Wickline, G. Rashed

To better understand the load shedding and the stress transfer on coal pillars due to room-and- pillar retreat mining in deep cover panels, researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted a monitoring field study. Two sites, at overburden depths of 1,000 ft (304.8 m) and 1,500 ft (457.3 m), were selected in a room-and-pillar mine operating in Southern West Virginia. The deformation and stress changes in the roof and two adjacent pillars at each site were monitored during the retreat mining process. The monitoring results and field observations were used to calibrate large-scale FLAC3D models for each site. The calibrated models were used to assess different sizes of roof bolts installed in deep cover areas. INTRODUCTION Deep cover room-and-pillar retreat mining is an important emerging issue that will intensify in the future as shallower reserves are depleted (Mark, 2009; Chase et al., 2002). During pillar retreat mining, the likelihood of local and/or global instabilities increases due to elevated stress levels near the pillar line because of the abutment loading. In the last decade, approximately 31% of the room-and-pillar mining groundfall fatalities in the United States occurred during pillar retreat mining. Between 2013 and 2017, this proportion increased to 55%, of which 50% of these fatalities were due to falls of roof and rib that occurred during pillar recovery (MSHA, 2018). One interesting piece of information about pillar recovery fatalities was that the victim was nearly always under bolted roof. Sheared and broken #5 (5/8-in), fully grouted rebar bolt failure contributed to three of four fatal roof fall incidents that have occurred in deep cover retreat mines (NIOSH, 2010). This claim raised the following question at the study mine: Is it safe to use a 4-ft long #5 (5/8-in) rebar bolt grade 60 at a depth of cover more than 1,000 ft (304.8 m)? There was some concern about shear failure of the #5 (5/8-in) rebar bolt at a depth of cover over 1,000 ft (304.8 m). To answer the question and to reduce accidents and fatalities caused by ground falls due to room-and-pillar retreat mining in deep cover panels, the National Institute for Occupational Safety and Health (NIOSH) monitored the roof and rib deformation and the change in vertical pressure within two adjacent pillars during pillar recovery. The study was conducted at two deep cover sites in a room-and-pillar mine located in Southern West Virginia that operates in the Lower War Eagle (LWE) seam. The monitored sites were selected at 1,000 ft (304.8 m) and 1,500 ft (457.3 m) depths of cover. In this paper, site-1 represents the monitored site at 1,000 ft (304.8 m) of cover, while site-2 represents the monitored site at 1,500 ft (457.3 m) of cover. For this study, large-scale FLAC3D numerical models were calibrated based on both field observations and instrumentation results. The calibrated models were then used to compare the ground response and the induced stresses of two pillars at instrumented sites 1 and 2. The maximum lateral displacement (roof shift) obtained from the calibrated large-scale FLAC3D models was applied to a small-scale FLAC3D bolted models, the safety factor for axial stresses of the simulated roof bolts was calculated at the deep cover sites.

Jan 1, 2019

By Edgel P. Stambaugh

Oxides are important for use in the production of metals, ceramic hardware, paints, permanent magnets, magnetic recording tapes and many other uses. In some of these applications, particle morphology, degree of crystallinity, purity, and homogeneity are relatively insignificant, while for other uses, these same properties are of critical importance. Many conventional processes are based upon recovery of the oxides from aqueous solutions by processes which include neutralization, evaporation of solvent, and precipitation of a complex salt. Consequently, many of these techniques lead to oxides of low quality. There is a growing demand for oxides of high quality, i.e., materials with narrow particle size distribution, controlled particle morphology, high purity, few structural defects, and high degree of crystallinity and homogeneity. This demand has prompted industry to search for new approaches for the manufacture of these special materials. One new approach for preparing high quality oxides is hydrothermal precipitation. This process has been used for preparing simple oxides such as ZrO2; mixed oxides such as ZrO2-SiO2; and complex oxides such as BaTiO3. These oxides were prepared in a high state of purity with a high degree of crystallinity and., in many cases, without the addition of precipitants. Many impurities- that are normally precipitated by conventional methods such as neutralization present no problem since they remain in solution. Nature of the process and its applications are discussed in this article.

Jan 1, 1977

By Samuel A. Rasmussen

Lead anodes are used in commercial copper electrowinning operations, yet there is no method to calculate anode life. To be discussed in this paper are operating characteristics of rolled plate (Pb,Sn,Ca) alloy anodes at Morenci's electrowinning tankhouse along with fundamental operating conditions and how the anode reacts to these conditions. These include anode maintenance, electrolyte temperature and viscosity, cobalt concentration, and manganese concentration. Also to be discussed are anode substrate characteristics under normal operating conditions and how the corrosion rate is affected by changes in operating conditions.

Jan 1, 1995

By R. P. King

A new device, called the dual impact load cell, has been developed and built at the Comminution Center to measure fracture energy and damage accumulation in brittle particles that are subject to impact. The results show that damage accumulation during impact is not a significant factor in determining the fracture energy or the particle strength. However, predamage induced by thermal pretreatment of the particles has a significant effect on both fracture energy and particle strength.

Jan 1, 1995

By Dennis Molvik, Omar Fulton, Chris D. Breeds, Don Gonzales

This paper presents and describes the South Interceptor Parallel Phase III Contract C93012C, which involved construction of a nominal 2.7 m (9-ft) finished diameter sewer conveyance using both pipe jacking and conventional tunneling methods. Earth Pressure Balance (EPB) excavation was required to minimize the potential for settlement beneath a main rail line, overpass, sensitive wetland, areas of contaminated soils, and nearby structures. Ground conditions predicted in the Geotechnical Baseline Report included low plasticity, clayey silt (40 to 10%) and silty sand (60–90%) with pieces of wood such as logs, stumps, branches and other tree fragments. Soil cover ranged from 2.7 m (9-ft) to 5.4 m (18-ft) over the tunnel crown with a groundwater table between 1.5 m (5-ft) and 3.7 m (12-ft) deep.

Jan 1, 2003

"Cast blasting is the primary means of overburden displacement in a surface coal mine. It serves two purposes; fragmenting the rock and throwing it directly to its spoil pile using explosive energy. Increased throw minimizes costs by reducing the amount of material that needs to be rehandled. Prior studies have shown that by only changing blasthole timing with the same blast design, fragmentation and throw alter. It is necessary in cast blasting to optimize both fragmentation and throw, since larger fragments will require more wasted energy to throw the same distance. In an operating mine in Georgia, an optimum interhole delay for fragmentation has been found by studying timings from 0 millisecond (ms) to 45 ms. Instantaneous timing between holes increased the throw by more than 31 m (100 ft), but fragmentation was poor. Shock and detonation wave collision is a potential reason for this increased throw.Explosives are utilized extensively by the mining industry in order to break rock, as either ore or overburden, for hauling, loading and crushing. An effective production blast strives to achieve optimum rock fragmentation in order to increase the efficiency and reduce the costs of those downstream operations, while simultaneously meeting environmental regulations. The goal of blasting with respect to fragmentation is, according to Hettinger (2015), “to decrease the average particle size of the fragmented rock without overly increasing fines or, in other words, improve fragmentation.”Additionally, the distance the rock is transported by the explosive energy from the blast, also known as throw, can increase efficiency by reducing the amount of material that is rehandled by mine equipment. The primary situation in which this is desirable is the cast blasting of overburden across the narrow pit of a surface coal mine. A key variable in a blast design pattern that can be manipulated to optimize both fragmentation and throw is delay timing between detonations. The invention and increased utilization of electronic detonators have allowed for precise delay timings to be used between rows, holes and even multiple primers within the same hole. These recent developments in the blasting community have also provided an opportunity to investigate whether or not the mechanism of shock or detonation wave collisions caused by short timing delays are responsible for any increased fragmentation or throw. This experiment attempts to demonstrate if an increase in throw can be achieved while maintaining optimum fragmentation."

Jan 6, 2017

By S. A. Montague

In spite of the many new insulating materials, both synthetic and manufactured, that have been put on the market since the end of World War II, and notwithstanding the many millions of dollars applied to the development of synthetic mica, natural block mica1 is still a most indispensable insulator in various electronic components. It will remain so, barring some spectacular break-through in research that might provide a substitute fully acceptable as a replacement for mica in all of its superior properties. But this is not to say the future for mica is assured, or free from serious problems. Technological advances have created problems requiring a solution to be found if future requirements are to be filled.

Jan 1, 1962

By S. E. Sankey

High anionic functionality acrylamide co-polymers and poly(sodium acrylate) are used as red mud flocculants in bauxite processing operations. These synthetic polymers are effectively displacing starch as the dominant polymer in red mud settling. The performance of these polymers is primarily dependent on the bauxite mineralogy, the alkalinity of the red mud slurry, and the anionic functionality and molecular size (viscosity) of the polymer. In this paper, the physical and chemical properties of the synthetic watersoluble polymers will be reviewed. The relationship between polymer structure and red mud slurry properties as they control polymer performance in settling red muds common to digester and washer circuits will be illustrated. The availability of polymers of varying functionality and viscosity will permit bauxite processors to make significant improvements in the economics of red mud disposal and valuable reagent recovery.

Jan 1, 1982

By Shaoyang Yan, Xinming Chen, Huazhe Jiao, Huaibao Chu, Chang Wang

In terms of the technical problems of rib spalling in large mining height coal face, a long-distance advanced pre-grouting layer flexible reinforcement technology is proposed in this paper. Based on the mechanism and failure mode of rib spalling in the coal face, the mechanical properties of the aluminum plastic composite pipe were analyzed by using the tensile and compression experiment. The deformation and strength characteristics of “flexible pipe + grouting” specimens were studied by uniaxial compression test, splitting test, and shear test. The UDEC numerical simulation software was used to simulate the reinforcement effect of “flexible pipe + grouting” at different positions. Combined with the field application, the feasibility of long-distance advanced pre-grouting layer flexible reinforcement technology was verified. The test results show the following: The coal face has the characteristics of brittle and large deformation. The aluminum plastic composite pipe has the characteristics of good elongation and tensile strength, which can endure the large deformation of the coal face. The “flexible pipe + grouting” can improve the tensile and shear strength of coal. The UDEC numerical simulation analysis indicated that the grouting hole layout of “flexible pipe + grouting” has a significant difference in the reinforcement effect of the coal face. Compared with single row grouting reinforcement, the reinforcement effect of double row grouting holes 1.5 m and 3.0 m away from the roof is better. According to the field application, it is feasible to use aluminum plastic composite pipe as a flexible grouting pipe to reinforce coal seam with 80–100 m long-distance pre-grouting. Long-distance advanced pre-grouting layer flexible reinforcement technology can improve the daily production of coal and reduce the support cost of the coal face. As a new method of reinforcement, long-distance layered flexible reinforcement has a significant effect on the prevention and treatment of rib spalling in large mining height coal face.

Sep 27, 2022

By Kelly F. Bailey

The issue of regulating non-asbestiform varieties of the amphiboles actinolite, tremo1ite, and anthophyllite to the same degree as asbestos has been studied in detail by the National Stone Association. The ramifications of such a regulation, and the over simplistic regulatory definition of a fiber, are enormous not only for the aggregate industry and its users, but also for the nation. Evaluation of the health, geological, mineralogical, technical, economic and legal issues do not support an "asbestos-like" regulation of non-asbestiform minerals. The adverse consequences of regulating non-asbestiform varieties of actinolite, tremolite and anthophyllite like asbestos would be magnified many times if a similar standard for generic mineral fibers were promulgated.

Jan 1, 1988

By R. Venugopal, V. K. Saxena, Veerendra Singh

"Ore morphology plays a vital role during the milling and liberation of minerals. This study was carried out to understand the role of mineral crystallography and mineral interfaces on the milling and liberation processes. Data related to mineral crystallography, Vickers Hardness Number and beneficiation processes were collected from literature, and detailed statistical analysis was conducted to relate these parameters. Review of the crystallographic information of minerals present in ores indicates that molecular weight and cell parameters significantly affect milling and liberation characteristics. Mineral interfaces were classified into the three categories of coherent crystals, semi-coherent and incoherent crystals, and breakage behaviors were studied. The studied cases revealed that these material interfaces control the micropore properties that play a vital role in the initiation of intergranular and intercrystalline fractures which occur in siliceous manganese ores and dolomite as a result of thermal treatment. In contrast, banded hematite jasper and coal exhibited a much more complex fracture pattern due to their coherent interfaces and finer physical associations. This study explains the effect of the various types of interfaces on milling, and the approach can be helpful in developing a methodology to enhance mineral liberation with minimum energy consumption.IntroductionComminution is a vital unit operation in the mineralprocessing, cement-making, power-generation and pharmaceutical industries. Its importance in mineral beneficiation operations is increasing every year as a result of the growing need to exploit lower-grade ore bodies and process reject materials (Blazy et al., 1994; DOE, 2005). Low-grade ores require significant energy during grinding to liberate the valuable minerals, which are further separated from the gangues by various beneficiation methods. Various attempts have been made to enhance mineral liberation during grinding to minimize energy consumption. Most of these studies focused on the analyses of the compression mechanism, chemical additives, thermal treatment, microwave treatment and electric disintegration (Klimpel and Austin, 1982; Norgate and Weller, 1994; Bearman et al., 1997; Kumar et al., 2010; Wang et al., 2011; Singh et al., 2012). However, many of these efforts had limited success, and there is a need to see the problem from a fresh perspective."

Jan 1, 2015

By Clifford W. Schultz

Four native copper ores, two conglomerate and two amygdaloidal, were tested to determine their amenability to sorting. One of them, a conglomerate ore from the Kingston mine, showed a high sortability as evidenced by an 80 pct recovery of copper in the minus 6-, plus 1/2-inch size range. Using the Kingston as a case example, the cost of mining and concentrating was estimated for a standard case and five optional cases involving varying degrees of sorting. This analysis indi¬cates that the production cost per pound of copper can be reduced on the order of 1 to 1-1/2 cents per pound along with a significant decrease in capital investment.

Jan 1, 1975

By Malcolm Reeves

The heavy oil reservoirs of Alberta and Saskatchewan include sequences of unconeolidated silts and fine sands which respond in an unusual manner when subjected to the high temperature and pore-fluid-pressure associated with steam injection and other thermal enhanced recovery techniques. Apparent transient connections are suddenly established between producers and injectore and there is an associated enhancement in oil (and sand) production. These phenomena have been attributed to local fluidization and piping processes which are known to occur in situations where high pore-fluid-pressures prevent the mobilization of intergranular friction. These breakdown processes may be associated with the penetration of tongues of the heated reservoir fluids with suspended sand into the creep sensitive intact reservoir since the viscosity ratios are sufficiently high for viscous fingering instability of the fluid-fluid interface. A program of laboratory tests has been carried out to measure the strength characteristic of saturated oil sands at a variety of temperatures and fluid pressures. These tests suggest, that in common with the coarser Athabasca sands, the Waseca sands have very little cohesive strength and show the characteristic dilational failure response of dense sands. Some special tests, devised to determine the relative ease with which samples can be fluidized, confirm the expected susceptibility of the fine- sand silts. Both piping and fluidization can be readily induced at in-situ reservoir temperatures and pressures. Analysis of stresses around wellbores suggests that fluid-pressure gradients may be sufficient to initiate piping and that backward erosion along streamlines may link producers and injectors. Such pipes may act as well “adits” gathering oil from the heated reservoir and contributing to enhanced production rates. Mechanical breakdown of the reservoir by drilling, injection and production processes provides a consistent possible explanation for the sand-cut response of production wells.

Jan 1, 1986

By Max B. Holfeltz

[Many factors impact the selection of one mining method over another for deep seated, thick seam coat deposits. Generally if an operating mine is recovering coal at high volumes from thick seams then a truck/shovel fleet is required for coal loading. The next consideration is how to remove the associated burden. If an operation has relatively small amounts of burden associated with the coal then a truck/shovel fleet may be employed for burden removal simply to standardized the entire mine equipment concept. On the other hand large amounts of burden associated with the coal can justify employment of draglines for burden removal. Specific economic, productive, and physical factors contribute to the final decision.]

Jan 1, 1983

By G. R. Marchant

The nonferrous industry has for many years maintained monitoring stations in agricultural areas in the vicinity of smelters to collect data concerning impact of smelter emission on agricultural crop production (Thomas and Cross, 1928). However, in 1967, the United States Congress passed the Clean Air Act which was amended in 1970 (Marchant, et al., 1977). The interpretation of this act by the Environmental Protection Agency (EPA) made it necessary for the industry to install extensive real-time ambient sulfur dioxide (SO,) monitoring systems. This was only the tip of the iceberg. Since that time as a result of additional laws and agency directives, it is now necessary to monitor concentrations of a number of substances -in both air and water. And unless there is a major change in government thinking, this trend will continue during the decade of the eighties. It is difficult to estimate the full impact of these laws. Nevertheless, the impact is large and affects every person in the United States today (Anon., 1972; Rockefeller, 1971; Nelson, Yeager, and Guptill, 1973; and Anon., 1975). It prohibits the burning of trash and paper in most areas of the country. It increases the cost of transportation and the price of motor vehicles. It increases the, cost of nearly everything that is manufactured. In industries which compete in the international market, it reduces their competitive position. In some industries the environmental impact is felt on costs of goods sold in the vicinity of 25% of the total production costs. The major portion of these costs is not due to the monitoring systems but instead is due to the increased cost of production facilities, equipment, and raw materials in industries that are required to comply with environmental regulations.

Jan 1, 1979

By John D. Smart, John W. Sager

The following paper is an evaluation of the instrumentation programs on recent Corps of Engineers tunneling projects. The authors have first-hand knowledge of the NORAD Cheyenne Mountain Complex (NCMC) Expansion Project. Information on the other projects comes from conversations with those directly involved in the instrumentation programs and from referenced reports. The specific objectives of this paper are: (1) to state the purposes of the instrumentation programs, (2) to discuss the benefits gained from the instrumentation, and (3) to present conclusions from this study that will provide guidance to those planning instrumentation on future projects. Presentation of detailed descriptions of the projects and instrumentation data is limited to that necessary to the accomplishment of the above objectives. NCMC EXPANSION PROJECT The NCMC is located at a depth of approximately 800 feet in Cheyenne Mountain near Colorado Springs, Colorado. For the current expansion project new chambers were mined to accommodate a new diesel power plant and associated cooling and air handling equipment. During 1971 some 55,000 yd3 of granite were mined through existing access tunnels for this expansion. A model of the new excavation is shown in Figure 1. The light shaded areas are new openings, and the dark areas are portions of the existing operating complex. The large chamber to the right is the power plant chamber and has a span of 67 ft, a height of 50 ft, and a length of 172 ft. The other large chamber on the lower level is the cooling tower chamber and has a span of 38 ft, a height of 45 ft and a length of 185 ft. The small chamber on the upper level has a span of 20 ft and is 27 ft high and 140 ft long. Other major excavations are the 18 ft diam air tunnel

Jan 1, 1997

By R. A. Jankowski

Although the number of operating longwall mining systems has remained relatively constant, longwall production levels during the last five years have increased significantly. In the United States, longwall mining now accounts for approximately 50% of all underground coal production. While longwalls are highly productive and offer other advantages, operations employing this method of mining continue to experience dust-compliance problems. This increased longwall productivity has meant that far more dust is being produced. An improved understanding of the longwall face-ventilation system and the advancement of face-ventilation technologies are necessary to ensure all face personnel are allowed to work in an environment that is free of excessive levels of airborne respirable coal mine dust. The Dust and Toxic Substances Control Branch, National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, examined several basic principles of the long wall face-ventilation system and has evaluated the effectiveness of numerous improved face-ventilation techniques for longwall mining systems. These include identifying improved techniques for measuring face-ventilation parameters on longwall mining sections and investigating the fundamental relationship between face airflow and the entrainment and dilution of respirable coal mine dust. Studies have been completed to determine the impact on face dust levels of using belt entry air to ventilate the longwall. Novel methods have been identified to increase the face air¬flow and to manage face airflow to effectively minimize dust exposure to face workers. Unique systems of auxiliary face ventilation have been developed and evaluated at full-scale, simulated longwall test facilities. The theoretical and applied aspects of each of these principles and technologies are discussed. Application of these results throughout the longwall mining industry, as documented from surveys conducted in the early 1980s and 1990s, have reduced the health hazard associated with excessive exposure to respirable coal mine dust.

Jan 1, 2000

By P. Gelfi, G. Hill, A. Showell, V. Martins, R. Dunne, R. Jenkins

Carbon attrition losses are not usually a prime consideration for CIP equipment selection and CIP plant design. However, the costs as a result of carbon attrition and associated gold lost with carbon can be high. Recorded carbon losses for Newcrest operating gold plants were shown to vary widely from plant to plant. The Tuckabiana plant recorded an overall loss of only 0.3g carbon /t ore which is very low by industry standards. A comparative carbon management study was undertaken by Newcrest to highlight the reasons for the excellent record of Tuckabiana operation compared to other Newcrest plants. This paper discusses the results of the comparative study and high­lights areas of concern with respect to carbon attrition.

Jan 1, 1995

By J. K. Neathery, T. X. Li, H. Ban, J. L. Schaefer, J. M. Stencel, X. K. Jiang

Pneumatic, triboelectrostatic processing of physical mixtures containing fine (-200 mesh) particulate may have significant application potential in the mining and energy industries. Such dry processing methods, especially for finely comminuted materials, have not been examined in as much detail as wet processing methods nor have been part of the training or education of mining and process engineers. We have examined fundamental and applied physical and engineering factors controlling triboelectrostatic beneficiation of fine-sized physical mixtures, one of which - combustion fly ash - has size, heterogeneity and mineral concentrations typical of those expected in mined minerals. The applicability of dry processing, however, cannot be readily evaluated because of the unavailability of standard procedures for process assessment.

Jan 1, 1999