Search Documents

By Hans Ehdwall, Erling Strandon, Friedrich Steinhäusler, Victor A. Leach

INTRODUCTION The basis for any measures in radiation protection is the quantitative assessment of the radiation exposure. Due to the extensive requirement in health physics manpower and related cost it is necessary to develop certain criteria regarding the necessity of monitoring and the selection of population groups to be monitored. Depending on the overall objective of the particular programme, the specific requirements for the measurement of atmospheric levels of radon, thoron and their daughters for practical radiation protection purposes differ significantly for those in the case of research applications, such as use of data for epidemiological studies. As part of the OECD-NEA Programme on Radon Dosimetry and Monitoring Task Group 1 reviewed available models for lung dosimetry in the case of inhalation of radon 222, radon 220 and their daughters (James et al., 1981). Using defined reference atmospheres for underground- and open-pit mining conditions as well as for dwellings, normalized conversion factors were calculated for the mean bronchial dose (mGy) per Working Level Month exposure (WLM). Task Group 2 discussed the features and adequacy of the Working Level (WL)-concept as a physical correlative of the absorbed lung dose and its limits of confidence and accuracy (Johnson and Leach, 1981). The WL-concept was found acceptable for radiation protection purposes provided that modifying factors like particle size, unattached fraction and respiratory minute volume did not cause the effective dose equivalent per WLM as calculated by either the James-Birchall or Jacobi-Eisfeld lung models to be more than 50 % above that given by ICRP of 0.01 Sv/WLM. For application in epidemiological studies the WLconcept is considered acceptable if the calculated absorbed dose to the tissue does not vary by more than 50 % (at the 95 % confidence level) from that given for defined reference conditions. In the following, objectives and requirements for the measurement of radon, thoron and their daughters are discussed for operational health physics routine and special research applications according to the scheme outlined in Fig. 1.

Jan 1, 1981

By R. D. Stewart

Abstract. Induced fluorescent sorting is a means of beneficiating an ore by selective labeling with a reagent combination which fluoresces when activated by ultraviolet light The reagent combination normally consists of a surface active compound and a fluorescent dye. The surfactant adheres selectively to a specific surface and carries the dye with it. Upon activation with ultraviolet light, the labeled pieces, in the size range 1.27 cm to 20 cm (0.5 to 8 in.), are detected during free fall by photosensitive cells and ejected by water jets. Either ore or gangue may be labeled.

Jan 1, 1980

By Wen Lan Chen

In the plant where the 800m diameter cyclone was tested, 500 STPH of 50m x 0 raw coal was pulped in a heavy medium tank and pumped originally to four 700mm heavy medium cyclones. For the test one of these units was replaced by an 800mm diameter cyclone with the subsequent feed pressure for both units sets at approximately 15.0 psi. Since this was a feed to zero plant, an appropriate bleed of heavy medium to the dilute medium circuit was established to en- sure that the cleaning of the 500m x 0.5mm raw coal would not be adversely affected by high levels of 0.5mm x 0 fine coal present in the heavy medium. The medium gravity measured varied between 1.41 and 1.43. During a three-hour test on June 10, 1983, the raw coal sample was collected from the feed belt while the clean coal and refuse samples were collected separately at proper locations along the product streams of the two different diameter cyclones. All of these samples were shipped to the laboratory for screen and sink- float analyses. The raw coal screen and ash analyses are shown in Table 1.

Jan 1, 1984

By J. Kallioinen

Theoretical considerations, experimental results and plant experience have lead to a new design concept called the unit reactor approach. It has been successfully implemented to the largest flotation cell on the market, the 4000 cu ft OK TankCell. The work has also lead to a new operating idea called size specific flotation. The paper discusses these concepts in the view of full scale field experiments. In large scale porphyry copper flotation experiments conducted in Chile the new large TankCell with its new low energy input Free Flow mechanism out-performed the more conventional designs. The recovery was substantially better, especially in the coarse fractions. In some experiments the difference in total recovery was up to 10%-units and the savings in total energy consumption at the same time over 40%.

Jan 1, 1995

By Joseph Keenan

In March of 1994, Dynatec Mining Limited entered into a contract with PCL Civil Constructors to carry out the underground excavations for the Algonquin Power Corporation’s15 Megawatt Nagagami hydro-electric power station located near Hearst, Ontario, Canada. Dynatec completed the work for this project in early October 1995. Dynatec Mining Limited’s work included the excavation of a 175 meter long penstock driven at a grade of -25% to a 4000 m3 powerhouse located 50 meters below the intake elevation. A 1200 meter long tailrace was driven from the Nagagami River to connect with the powerhouse. Two 50 meter raises were driven from the powerhouse to surface to pro-vide access for equipment and personnel. The excavation of the tailrace tunnel(5.8m x 5.9m) was completed using Dynatec’s Long Round Jumbo Technology.

Jan 1, 1997

By K. R. Weller

In recent years, a variety of new or substantially modified grinding machines have been offered to the mining industry with claims of improved performance relative to standard grinding machines especially rod and ball mills. The incentive for developing such new machines is high, because costs associated with grinding are a very substantial part of the total costs of processing run-of-mine ore, and gold ores are no exception in this regard. The incentive is also high because of the very low conversion of input energy to comminution energy in most tumbling mills. If the most energy-efficient means of mechanical size reduction is slow compression of single particles, then this energy amounts to only about 3% of that used in tumbling mills. It would seem, therefore, that there is a huge potential to do better. This paper examines three types of grinding machine for which claims of higher energy utilisation ( amongst other beneficial claims) have been made, namely the high pressure grinding rolls, the vibrating drum mill and various styles of stirred mill. It presents evidence concerning the claims, examines the range of particle size and particle size reduction over which benefits might reasonably be expected to accrue, discusses the major issues in contention and briefly describes the research the CSIRO Division of Minerals has in progress, both independently and collaboratively, the latter mainly with the Julius Kruttschnitt Mineral Research Centre (JKMRC) via the Cooperative Research Centre for Mining Technology and Equipment (CMTE) and the Australian Mineral Industries Research Association (AMIRA). There are many criteria which may be chosen to assess relative performance of grinding machines. Those used below are:

Jan 1, 1995

By D. Tepavac, S. Simmonds

"The high virgin horizontal in situ stress field in the Sydney Basin and its impact on civil engineering projects is a well-known and accepted phenomenon found in significant literature (e.g., Pells, 2013). The prevailing high-stress effects depend on many factors — rock quality, tunnel orientation, proximity of geological features to tunnel crown, size and shape of opening, depth of excavation and stress magnitude. The behavior of the rock mass under high in situ stress conditions can cause stress fracturing and consequent dilation of the tunnel periphery, resulting in rock spalling at the tunnel crown/ invert or raveling of rock blocks on the tunnel sidewall. This type of failure is of a brittle nature and may create construction and safety risks during tunnel excavation, if it occurs behind the excavation face where ground support has already been installed. Therefore, the associated risks need to be managed during construction. This paper presents the design strategy adopted to mitigate these adverse tunneling conditions for the WestConnex Project to-date. Overview of the WestConnex M4 East and new M5 tunnel projectsWestConnex is one of the New South Wales government’s key infrastructure projects. This 33 km (20.5 mile) project aims to ease congestion and connect communities and is the largest integrated transport and urban revitalization project in Australia. It was a key recommendation of the State Infrastructure Strategy released in October 2012. It brings together a number of important road projects, which, together, form a vital link in Sydney’s Orbital Network. These road projects include a widening of the M4 east of Parramatta, a duplication of the M5 East, and new sections of motorway to provide a connection between these two key corridors. The WestConnex project includes a number of stages: Stage 1a: M4 Widening; Stage 1b: M4 East; Stage 2: New M5; and Stage 3: M4–M5 Link. The tunnel design referenced in this paper relates to Stage 1b and Stage 2 of the WestConnex Project (Fig. 1)."

Dec 1, 2018

By R. Q. Honaker, D. P. Patil, A. Sirkeci

Due to increased production of fine coal during mining during this century and inefficient fine coal recovery technologies, a vast reserve of high quality coal currently exists in refuse ponds. A novel fine coal circuit consisting of a hindered-bed classifier, an enhanced gravity concentrator and a flotation column has been evaluated for the recovery of fine coal from refuse ponds. The treatment of a pond derived from Pittsburgh No. 8 seam coal resulted in the production of a premium fuel containing less than 5% ash and a calorific value of about 30,173kJ/kg with 60% mass yield. The results from the treatment of two refuse pond materials will be presented in this publication.

Jan 1, 2000

By P. C. Rath, K. Srinivasa Rao, T. Subbaiah

A process for the recovery of nickel from ammoniacal leach liquor through an integrated solvent extraction-electrowinning (SX-EW) flowsheet was tested on a pilot-plant scale. The objectives of the test run were to assess the reproducibility of laboratory-scale data in a large-scale continuous operation and to study the build up of impurities in the system. The pilot-plant test was conducted under operating conditions that were established from the laboratory-scale experiments. Efficiencies of nickel extraction, nickel stripping and ammonia scrubbing were comparable to the laboratory-scale values, whereas the current efficiency during nickel electrolysis was observed to be less than the laboratory-scale values. The electrodeposited nickel contained some cobalt and iron impurities.

Jan 1, 1998

By Ian Sheppard, John J. Chen

This paper describes the development of the underground mining methods employed for narrow silver-lead-zinc orebodies at the Isa Lead Mine. Cut-and-fill methods were the chief underground mining methods for the narrow orebodies at the mine over 35 years ago. Benching methods were introduced approximately two decades later, and quickly replacing the cut-and-fill methods. The cut-and-fill methods and the benching methods are briefly reviewed in the paper. The benching methods and technologies have been continually evolving and one of the recent achievements is a multi-lift benching method. The multi-lift benching method is described in detail.

Jan 1, 2001

Relatively few longwall mines in the U.S. operate under multiple seam conditions where the two seams are less than 200 ft apart. This paper describes the experience of six that do. These operations are located in PA, WV and UT, and include examples of both undermining and overmining. Some operate above or beneath their own workings, others are in historic mining districts and must contend with abandoned mines that are decades old. The lessons that these mines have learned cover a broad range of topics, including: • Whether to stack gateroads or place them under old gob areas; • How to size pillars and select artificial support to cross longwall stop lines; • How to use yield pillars to minimize multiple seam stresses and coal bump potential, and; • When to anticipate the creation of pathways for gas, water, or oxygen between current and abandoned gobs.

Jan 1, 2007

By K. N. Han, N. S. Kim, H. Yoon, J. S. Sohn

The leaching behavior of silver and silver oxides in ammonical solutions has been studied. The current study is concerned with an effective recovery of silver from secondary sources such as spent silver batteries. Silver associated with these batteries appears in various forms including metallic silver, argentous oxide, Ag2O and argentic oxide, AgO. The leaching behavior of metallic silver in ammoniacal solution has been studied using an electrochemical mehtod. Oxidants used in this study include hyperchlorite, hydrogen peroxide, bromine and iodine. Results on cyclic polarization and Tafel plots on the silver anode in ammoniacal solutions are presented and the results are discussed. The dissolution rate of metallic silver in ammoniacal solutions is also compared with those of silver oxides.

Jan 1, 2002

By F. T. Paleari, J. A. Finch

Radial gas holdup profiles were measured in a 50-cm-diam, 400-cm-high flotation column using a multi-cell-conductivity probe. Three bubble-generation systems, including a system with up to eight vertical filter-cloth spargers, a system with three horizontal filter-cloth spargers and a system with three (horizontal) Cominco-type spargers, were examined. The variables investigated were the number of spargers, the symmetry of their arrangement and the height above the spargers. Batch water containing up to 20 ppm frother was used. Generally, the profiles tended to be uniform (flat) with some profiles exhibiting a slight "wavy" pattern. The vertical sparger arrangement proved to be the most difficult in which to achieve a profile symmetry. The horizontal spargers gave uniform profiles at right angles to their length but gave decreasing gas holdup along their length. The Cominco-type spargers gave slightly less scatter in the data. Switching off selected spargers to simulate a malfunction did not produce strong asymmetry in the profiles.

Jan 1, 1995

By T. R. von Ow

The method of powering mills such as AG, SAG and Ball has a long and technically interesting history. It can be said that almost every decade in the last half century had its own trend. The trends were dominated by the market demand, the advanced process development and requirement of the mechanical and the electrical technology but mostly by the price of the applied technology. The increasing size of the ring geared mills in the last years requires more awareness on the drive train solution. Special attention must be paid to the mechanics and the requirements of the power grid. Operational challenges such as soft starting and controlled operation as well as the protection of the equipment have gained importance. Frequency converter drive solutions dedicated to single or dual pinion ring-geared mills offer significant advantages over conventional drives due to their application specific features and controls. Solutions with low speed motors as well as high speed motors cover all possible configurations available for ring geared mills.

Jan 1, 2010

By C. R. Landis

The Wyoming bentonite industry continued its run of stable, if not strong, growth in its complex markets. Growth at the macroscale was fueled by a strong domestic economy, the weakening of the U.S. dollar in the global market and strong worldwide global demand. Challenges to the benchmark of the industry were rapid and saw ongoing increases in raw material costs(pallets, bags and additives), higher energy costs and higher overall transportation costs for all modes of movement. Exports continued to be assisted by dollar depreciation (5 percent to 10 percent) from January 2004to January 2005. This depreciation followed the significant weakening of 2003. And it was most favorable during the pullback in fuel and shipping rates in the second half of the year.

Jan 1, 2005

By C. H. Rawlins

Deep bed media filtration is used as a tertiary treatment step (after hydrocyclones and flotation cells) to remove fine oil droplets and solids from oilfield water before reinjection disposal or to remove particulate material from surface waters used for waterflood injection. Oil and solids injection requirements are typically <5 ppm concentration at <2 micron diameter. The preferred media for produced water filtration is walnut or pecan shell, however the use of this media has evolved by trial & error and the fundamental mechanisms that occur during separation and media cleaning have not been investigated. A project was initiated to fill in this knowledge gap by analyzing the physical, mechanical, chemical, and hydrodynamic properties of six types of granular filtration media (12/20 mesh size): garnet, silica, anthracite, pecan shell, English walnut shell, and black walnut shell. Comparison of bed packing, oil wetting, attrition resistance, particle strength, and fluidization has led to an understanding of the preferred filtration media for separation of fine oil droplets and solids.

Jan 1, 2010

By Richard Jr. Ray, Richard Druesedow

The Virginia Operations of Consolidation Coal Co. include a diversity of mine fan configurations which have been tested to quantify pressure losses through the inlet ductwork. Airflow and pressure measurements were taken at four shaft sites to calculate losses for the 90-degree bend at the top of the shaft and the self-closing dampers or closing doors located between the shaft and fan. Velocity contours were then developed from the test data to determine flow patterns in each fan system component. In addition, yaw and pitch angles of airflow through the fan annulus were measured to evaluate turbulence levels created by various inlet ductwork designs. The test results indicate that proper design of the shaft collar and ductwork arrangement for main mine fans can substantially reduce system pressure losses and air turbulence. BY minimizing the pressure drop experienced on the surface, these design improvements enable the bulk of the total pressure developed by the fan(s) to be utilized in the mine.

Jan 1, 1995

By William Hodder, Ehsan Alavi, Nader Ghasempour, Daniel Cressman

The Don River & Central Waterfront Coxwell Sanitary Bypass Tunnel (CBT) Project in Toronto will extend approximately 10.5 km from Ashbridges Bay Treatment Plant west under Lake Shore Boulevard, north under Bayview Avenue and east through the Don River park area to the Coxwell Ravine Park. The tunnel is currently being mined by using a shielded dual-mode tunnel boring machine (open and close) capable of operating in EPB mode and lined by using a precast concrete segmental tunnel linear with an internal diameter of 6,300 mm and external diameter of 6,900 mm. The CBT is expected to be excavated mainly through shale bedrock of the Georgian Bay Formation, at approximately 50 meters deep. The tunnel crosses a buried bedrock valley in two locations, in the southern portion of the alignment, adjacent to the Don River, and at the northern portion of the alignment approaching the CX-1 shaft. In these two locations, the bedrock cover is expected to be less than 6 meters. The risk of encountering weathered bedrock, significant ground water inflows or surficial soil deposits through these buried valleys was identified during the design phase. The contract required the TBM to be designed with the ability to probe drill ahead of the TBM and convert to EPB mode if necessary, to cross this area. This paper will discuss the additional exploration that was performed by the contractor to identify the extent of this buried valley, the plan going into the zone of potential weathered shale, and the actual conditions encountered.

Jun 13, 2021

By Diane Germain, Normand Tassé, Claude Dufour

At the East Sullivan site, pore-waters underlying a wood waste cover that prevents sulfide oxidation are characterized by an anoxic environment, abundance of dissolved organic substrates, and near neutral pHs. Such conditions favor sulfate reduction and base metals precipitation as sulfides, as well as carbonate-metal precipitation. Pore-water composition from 1992 to 1998 shows a significant Fe2+ decrease. Therefore, the restoration strategy of that site capitalizes on these alkaline and reductive properties. Since 1998, a novel treatment of acid effluents, based on the recirculation of water discharged around the impoundment through the organic cover, is tested on the site. Available data gathered in 1998 and 1999 shows that the pH of recirculated water flowing within the wood waste cover increases by 2 to 4 units and that Fe,, concentrations decrease by a factor greater than 6.

Jan 1, 2000

By Dan Witkowsky

Beginning on June 11, 2007, as many as 36, kindergarten-to-grade-12 (K-12) teachers will participate in a program designed to educate them all about the mining industry. The 39th Annual A Total Concept of the Mining Industry – All About Mining, will be conducted by the Colorado Mining Association Education Foundation, Inc. (CMAEF) and the Office of Special Programs and Continuing Education (SPACE) at the Colorado School of Mines. This flagship program includes four intensive weeks at the Colorado School of Mines. During that time, more than 75 volunteer lecturers will “educate the educators” about mining and its importance to the United States and the world. During the learning process associated with obtaining a basic understanding of mining and all its aspects, the teachers will be hosted by hundreds of other industry professionals at 10 Colorado mining operations. Also visited will be a government earthquake center, a museum of mining and industry, an earth mechanics laboratory, a metallurgical research center, a metallurgical concentrator, an electric power plant and a steel mill. Questions before, during and after visits will be answered by another select group of volunteers who will travel with the teachers to the various sites.

Jan 1, 2007