Search Documents

By J. A. Finch, Zhenghe Xu, Z. A. Zhou

The generation of microscopic bubbles by cavitation may enhance particle-bubble attachment and improve flotation performance. It is shown in this paper that tiny bubbles or cavities can be generated by strong shear and turbulence in high speed liquid flows. These conditions create the necessary pressure fluctuations in the bulk water to cause the local pressure to drop below a critical value. The formation of bubbles is favored by high dissolved gas contents to promote gas diffusion into the cavities, and by the presence of surfactants to provide some mechanical strength due to the adsorbed film. Experimental results on bubble formation by cavitation and consequent flotation of fine silica (d50 = 1.6 µm) are presented.

Jan 1, 1995

By J de Cuyper, E. J. Parkins, H. L. Shergold, W. Freyberger

The paper is divided into two parts. The first part describes an investigation of the effect of temperature on the conditioning and flotation of an ilmenite ore with a 1:l oleic acid-fuel oil mixture as collector. During conditioning the pulp underwent characteristic changes of flocculation, deflocculation and dispersion which were monitored by measuring the power consumption of the conditioner motor. Optimum flotation results were obtained at the end of the deflocculation period. High ilmenite recoveries were obtained at high temperatures and high concentrate grades at low temperatures. The second part of the paper describes a study of the effect of temperature on the adsorption of oleic acid at the ilmenite/water interface. At high adsorption densities it was chemical and exothermic. Contact angles showed that the hydrophobicity of the collector-coated minerals increased with an increase in temperature.

Jan 1, 1976

By Y. G. Zhang

Interactive Dynamic Optimization Method (IDOM) will be presented in this paper. IDOM combines inventory theory, dynamic programming, computer simulation and interactive technique to formulate a production schedule for open-pit mines. This new method has been successfully used in metal mines of China for years.

Jan 1, 1986

By Kalyan K. Bhattacharyya

A systematic slope design for open-pit mines has become a reality only in recent years. Advances in the science of rock mechanics, coupled with extensive use of computers, have enabled the numerical solution of slope design problems which were not previously amenable to analytical or numerical solution. This slope stability study was performed for the UJV-SB open-pit uranium mine of the Getty Oil Co., located in the Shirley Basin area, Wyoming. The purpose of the study was to determine the appropriate slope angles for a starter pit. The data generated during the mining of the starter pit would test the initial design and suggest appropriate modification in the design for future mining in the project area. There had been a history of slope failures in the open-pit uranium mines in the area due to the low competency of the overburden materials and adverse hydrological conditions.

Jan 1, 1979

By J. C. Stankus, S. Guo, S. S. Peng

In this paper, a model is developed for a resin anchor bolt system in which the smooth bar is modeled by using one-dimensional truss elements, and the resin annulus is modeled by using axisymmetric elements. These two submodels are combined and then incorporated into an existing computer code called Roofbolt. After this development, all of the components in the resin anchor bolt system, including smooth bar, bearing plate and resin annulus, can be correctly modeled.

Jan 1, 1997

By G. A. Eltringham

Mining and extraction methods in the copper industry use basic technologies developed over a period of almost 150 years. Paradigm shifts in the industry have been rare, yet human involvement in the activities has changed dramatically. Clearly defined extraction paths have become more blurred as economic considerations broke down the barriers that had encouraged specialization. What had been a labor-intensive industry unfettered by environmental restrictions was forced to change. Better productivity and "cleaner" operations resulted in much higher capital costs on a plant basis. Many of the changes were truly innovative in the same spirit as in the mining revolution of the first decade of the twentieth century. What role will innovation play in the next 20 years as lower-grade, mixed-metal orebodies are exploited in more remote locations?

Jan 1, 1998

By R. Y. Wan, J. D. Miller, P. L. Sibrell

Three different refractory carbonaceous gold ores from the Carlin operation in northeastern Nevada were investigated to characterize the effect of passivation treatments on the nature of the carbonaceous material. The carbonaceous material was chemically isolated from the ores and passivated residues, and examined by FTIR spectroscopy, elemental analysis, and gold adsorption capacity. The main component of the carbonaceous material in these ores was found to be a naturally occurring activated carbon-type compound. Hydro-carbons were detected on rare occasions, but no evidence was seen for humic acids. Ore samples were passivated by autoclaving, or by treatment with sodium hypochlorite or gaseous chlorine. In some of the passivation tests, a new peak was observed in the IR spectra of the isolated carbonaceous material, that was due to carbonyl functionalities. However, all of the passivation treatments tested decreased preg robbing significantly. This suggested that the appearance of the carbonyl peak was due to the severity of the conditions during passivation, rather than the method used.

Jan 1, 1990

By R. Hogg, L. G. Austin, R. C. Klimpel

Slurry densities and holdup were measured for open circuit grinding tests in a laboratory overflow ball mill of 0.3 m diam by 0.6 m long, by emptying and drying after stoppage of the mill. Contrary to some other results in the literature, there was negligible variation of slurry level in the mill as a function of flow rate over a range of increase of flow rate of about 5 to I. However there was a gradual increase of solid holdup at higher flow rates because the slurry density in the mill increased. Equations are given for holdup and slurry density in the mill as a function of over flow diam, ball load, and feed slurry density. The average level of slurry necessary to give over flow was found to be much higher than that necessary to fill the mill to the overflow level at rest. The total level of balls and slurry was only increased slightly by ball loads higher than the overflow level. The overflow diam appeared to be the major controlling factor in determining the mill holdup.

Jan 1, 1990

By T. M. Campoy, J. R. Jones

When extending the life of an existing mine in Appalachia, it is common to acquire the adjacent reserves and extend the existing mine into it. The existing mine is often renovated to accommodate the new conditions. The existing mining system and the track and belt haulage systems may he modified while the new property is integrated into the old one. All of these changes create new constraints for the mine ventilation system (MVS) that require proper planning and control procedures. This paper presents a study that was carried out for the ventilation system of a newly expanded underground coal mine in the Appalachian region. The process of correcting the ventilation system of the existing mine is discussed. That is followed by a discussion of some of the stages of controlling the expanded system. Numerical data for these steps are also presented.

Jan 1, 1994

By Stephen J. Brower

Located in Central Nevada, The Round Mountain Gold deposit has been continuously mined since 1977. Present proven and probable reserves are 226 Mt (250 million short tons) at 1.1 g/t (.032 oz per short ton). The current open pit mining rate of 118 Kt (130,000 short tons) per day is producing 41 Kt (45,000 short tons) per day of ore to be processed by heap leach methods. At this rate, the current reserves provide a 16 year mine life. The high mining rate and strict ore delivery requirements mandate comprehensive and realistic mine planning. The mine planning process is described in three general steps: Deposit Modeling; Mine Design; and, Production Coordination and Support.

Jan 1, 1989

By D. C. Panigrahi

The paper presents the application of Object Oriented Programming approach for the development of a network simulation model based on nodal pressure method using linearised flow equations. The convergence and computational efficiency of the algorithm have been investigated. Finally the paper re- ports the validation of this algorithm in actual field conditions.

Jan 1, 1996

By G. Kritikakis

Rehabilitation of sites contaminated by oil products and chlorinated organic compounds is a costly task which affects the planning of urban and infrastructure development. An integrated approach based on the non-invasive geophysical technology is utilized for subsurface characterization of contaminated land. In this approach the localized information, provided by chemical analysis of soil samples collected from bore-holes, is used for the calibration of the geophysical data. This information is subsequently extrapolated to the area under investigation by combining it with the geophysical results, providing thus information about pollution accumulation, contaminants? flow and pollution sources. Two case studies are presented from sites contaminated by heavy metals (Venice, Italy) and oil products (Athens, Greece). Resistivity, electromagnetic and seismic methods were used in this approach. Namely, electrical tomography, electromagnetic mapping, ground penetrating radar (GPR), multichannel analysis of surface waves (MASW) and seismic refraction experiments were conducted. In Italy, the sections from the multichannel analysis of surface waves imaged successfully a buried channel where the pollution is concentrated. Preliminary results are also discussed from the geophysical survey in Greece where the thickness of the oil phase located on top of the water layer is 60 cm.

Jan 1, 2006

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

Jan 1, 1986

By F. M. Doyle, Jun Li, Milton E. Wadsworth, E. Peters

The Raman spectroscopic technique was used to study electrochernically oxidized pyrite in-situ. It was found that Raman-active sulfur oxidation products could be detected after a proper potential was applied to the pyrite electrode for a threshold period of time. There existed a minimum potential below which sulfur could not be observed. However, when the applied potential exceeded a certain limit, the intensity of the sulfur spectra decreased. The minimum potential at which sulfur could be observed changed with solution pH. For both acid (pH 2.7) and weak alkaline (pH 9.2) solutions, the minimum potential was 0.8 V/SCE, whereas for neutral (pH 6.5) solutions the value was 0.4 V/SCE. In strong alkaline solutions (pH 12.5) surface sulfur oxidation products could not be detected at any potential.

Jan 1, 1993

By Paul D. Tomlingson

Editor's note: This is the second of two articles on maintenance. Part one: "Downsizing maintenance to improve performance: Defining the downsizing task," appeared in the September issue of MINING ENGINEERING, pp. 1065-1066. Part one explained that downsizing must he an organizational change in which the mine moves to a more efficient, smaller maintenance organization. But the new, smaller organization must operate more productively. Determine initial reduction targets Reduce the workload - The initial reduction target can be determined by projecting manpower reduction as a result of discontinuing or deferring work. Start these reductions by not replacing personnel who retire or are disabled. Observe the right craft mix during this initial reduction. Improve productivity - Further reductions can come from better productivity. But achieving the higher productivity level will require a year or more. During this transition, the efficiencies of a well-defined program and a team organization must take hold.

Jan 1, 1994

By K. Fuenkajorn, S. Serata

Discussion by S. Serata and K. Fuenkajorn Background Results of the above study in the August 1991 issue of Mining Engineering offer valuable lessons in the solution of cutter-roof problems. The original study plan was initiated by the discussion authors to solve the problems using the "stress control method" of mining (Serata 1976, 1982; Serata, Carr and Martin, 1984; Serata and Gardner, 1986; Serata, Gardner and Preston, 1986; Serata, Gardnerand Shrinivasan, 1986; Serata and Kikuchi, 1986; Serata, Preston and Galagoda, 1987) However, the plan and the planner were changed to the arrangement reported in the paper. The change was considered reasonable at the time due to the mine engineers' uncertainties about the stress control method. Consequently, the basic principle of the study was shifted from the original stress control method to the method described in the paper, which will be called the "yield pillar method" for the purposes of this discussion. The paper convinces the reader that the yield pillar method fails to solve the cutter-roof problems. This doesn't mean that the stress control method also fails. Actually the contrary is true, as discussed below. Limitation of the yield pillar method The paper illustrates clearly how poorly the yield pillar method performs in solving the problem. The reason for this failure is the lack of the protective stress envelope needed to stabilize the cutter roof. Unfortunately, the protective envelope cannot be formed properly without utilizing the stress control method of mining. Changing the pillar size does not make much difference in the roof stability. Stress measurement The key issue is how to form the global stress envelope to make the gate entries safe for production. Therefore, measuring the stress condition of the ground around the mine opening is critically important to solving the cutter-roof problem, regardless of the method applied. With regard to the stress measurement, there is a serious question as to the reported stress state of [6 i = -51.7 MPa (-7499 psi), G2 = -44.5 MPa (-6458 psi) and 63 = -30.8 MPa (-4465 psi)]. It is mechanically impossible to have such a stress state at any location in the mine ground since the known initial vertical stress [o,,] is less than or equal to 800 psi. There may be a large stress state in the [61] direction, but that is possible only at the expense of the [63] value. Having the above stress tensors in the mine is simply impossible. The questionable, reported stress values could be attributed to the application of the overcoring method, which tends to produce erroneously large stress values in the extremely nonelastic mine ground. Stress control method The paper should be considered as a major contribution demonstrating the limitation of the yield pillar method. At the same time, the paper does not disprove the stress control method. However, in comparing the paper with stress control studies conducted in other similar failing grounds, the stress control method appears to be able to solve the problem more effectively. Therefore it is advisable that the mine not give up its efforts to solve the problem. [•] References Serata, S., 1976, "Stress control technique - An alternative to roof bolting?," Mining Engineering, May. Serata, S., 1982, "Stress control methods: Quantitative approach to stabilizing mine openings in weak ground," Proceedings, 1st International Conference on Stability in Underground Mining, Vancouver, BC, Aug. 16-18. Serata, S., Carr, F., and Martin, E., 1984, "Stress control method applied to stabilization of underground coal mine openings," Proceedings, 25th US Symposium on Rock Mechanics, Northwestern University, June, pp. 583-590. Serata, S., and Gardner, B.H., 1986, "Benefits of the stress control method," invited paper, American Mining Congress Coal Convention, Pittsburgh, PA, May 7. Serata, S., Gardner, B.H., and Shrinivasan, K., 1986, "Integrated instrumentation method of stress state, material property and deformation measurement for stress control method of mining," invited paper, 5th Conference on Ground Control in Mining, West Virginia University, Morgantown, WV, June 11-13. Serata, S., and Kikuchi, S., 1986, "A diametral deformation method for in situ stress and rock property measurement," International Journal of Mining and Geological Engineering, Vol. 4, pp. 15-38. Serata, S., Preston, M., and Galagoda, H.M., 1987, "Integration of finite element analysis and field instrumentation for application of the stress control method in underground coal mining," Proceedings, 28th US Symposium on Rock Mechanics, Tucson, AZ, pp. 265-272.

Jan 1, 1993

By M. J. McPherson, P. Mousset-Jones, J. Banik, F. Calizaya

Friction factors or coefficients of friction used to estimate the resistances of mine airways are, in the main, estimated from empirical measurements made in other airways considered to be of a similar geometry and type of lining. A somewhat more analytical approach, although still based on empiricism, is to estimate the ratio of the average height of the asperities to the hydraulic mean diameter of the airway (e/D ratio) and then to employ the Moody Chart or one of the equations that have long been established to represent the [coefficient of friction v Reynolds number curves] on that chart. Unfortunately, the Moody Chart and corresponding equations are based on pipes of uniformly distributed (sand grain) roughness whereas the asperities that exist on the surfaces of mine openings are frequently highly irregular both in their size and distribution. This is considered to be a major cause of discrepancies that have been found between coefficients of friction by the Moody Chart and those actually measured in mine airways. The work described in this paper examines an alternative method of estimating coefficients of friction for rough natural surfaces with uneven sizes and distribution of surface asperities. The technique utilizes the relatively recent developments in fractal analysis. A fractal dimension is determined from the topography of the surface. This has been correlated to coefficient of friction for a scale model of a mine airway. Further work is being carried out in actual mine airways. However, at this time, it appears promising that the fractal method may allow coefficient of friction to be predicted for given types of strata and method of roadway drivage.

Jan 1, 1993

By Marina K. Peshkova, Izabell V. Pomorova

Computer modelling system for definition optimal way of in- vestment under condition of diverse directions of activities mining enterprises has been created. The main purpose of paper is to introduce the new scientific approach of finding effective variants of investment for mining industry under free market condition in Russia, it can be also interesting for domestic and foreign investors.

Jan 1, 1996

By D. H. Davidson

In situ leaching (ISL) of copper has the potential of reducing both capital and operating costs for copper production. The ISL process combines surface facility (SX/EW) and wellfield operations, each of which must process the same total flow rate and pregnant liquor copper concentration. Commercial cost data are only available for SX/EW facilities. This paper discusses: the interaction between the principal wellfield costs associated with well modules, and wellfield start?up with SX/EW costs; how to estimate what the level of wellfield costs must be to optimize DCF/ROR; and how to relate these wellfield costs to orebody geologic and mineralogic characteristics.

Jan 1, 1988

By J. Pang, S. Chander

The results of an investigation to characterize the chalcopyrite/solution interface are presented. Several techniques were used, including galvanostatic and steady-state polarization, cyclic voltammetry and impedance spectroscopy. The results show that the dissolution of chalcopyrite was incongruent. Initially, at low potentials (< 0.12 V), iron species were released that led to the growth of an iron-deficient sulfide (IDS) layer (referred to as the "reacted layer" in this paper). Depending on the solution&apos;s composition, the dissolved iron might reprecipitate as a hydroxide layer. In the potential range of 0.12 V < E < 0.23 V, the IDS layer was passivating. In comparison, development of a passivating IDS layer under galvanostatic conditions led to a jump in potential to 0.48 V. The IDS layer began to dissolve at potentials greater than 0.24 V. The dissolved species precipitated to form a product layer in alkaline solutions. Continued oxidation involved diffusion of species through the reacted and product layers. At higher potentials (> 0.48 V), further oxidation led to the dissolution of the copper and sulfur species, with a resultant breakdown of the IDS layer. The changes in surface-coating properties, resulting from various electrochemical treatments, are discussed.

Jan 1, 1993