Search Documents

By S. Ash

Murray mine was one of the first Mechanized cut and fill underground gold operations in Northern Nevada. At the end of 2002 mine production began to decline and Murray entered a phase of remnant mining and began preparations to close down. The remaining mining took place along the ore waste boundary, in previously condemned areas, and in highly challenging ground conditions. To remain economically viable new techniques were implemented in operations, geology, engineering, and rock mechanics. These improvements pushed the edge of known and accepted mining practices and have allowed Murray to remain in operation today. History The Murray mine is located on the Jerritt Canyon property, which is located 45 miles north of Elko, NV in the Independence mountain range. Mining operations started at Jerritt Canyon in 1980 out of several open pits. In 1993 underground mining began in conjunction with a decline of surface mining operations. The transition from surface mining to underground mining moved the property into a new era. At the time there were limited examples of successful underground operations in the area from which to draw experience. Several mining methods were attempted with varying degrees of success and underhand cut and fill proved to be the most effective method. To date Murray has mined 1.2 million ounces at an average grade of .335 OPT utilizing this mining method.

Jan 1, 2006

By Jens Classen, Thomas Kurth, Karl G. Holter

High performance sprayed concrete equipment installed on two 9.4 m diameter hard rock TBMs enabled a continuous sprayed concrete lining for the entire contour in both tunnels to be performed concurrently with the advancing TBMs. Innovative layout of the sprayed concrete arrangements comprised ring beam constructions each with two independent spraying robots. Each of the spraying robots were independently connected to sprayed concrete pumps, as well as a high capacity concrete logistics system on the backup. The mix designs focused on long open-time, excellent pumpability and tough requirements on strength development. The achieved output capacities of the sprayed concrete amounts to an average of 15 m3 per hour. Peak capacities of 24 m3 per hour have been realized.

Jan 1, 2003

The objective of the fines flotation step in a coal preparation plant is to maximize coal recovery subject to a constraint on the allowable ash in the concentrate. The objective is achieved when the incremental ash is driven to a target value determined by an economic constraint. In this paper, a phenomenological flotation model and ash analyzer combination are identified that allow the development of a soft sensor for incremental ash and subsequently a model-based strategy which manipulates key flotation variables to achieve the control objective. A combination of plant tests and computer simulations are presented to evaluate control-system performance in one operation.

Jan 1, 1999

By W. Blake, J. Mahaut, W. Hustrulid

Division II at Kamoto mine in Kolwezi, Zaire represents a transition zone between Divisions I and III where transverse and longitudinal cut-and-fill rooms were being mined. Because this transition zone had been geologically depicted as being badly faulted the mining in this division had been deferred to a future time. However, to increase production and to reduce mining costs by carrying out the mining of the 3 divisions simultaneously, it was decided to mine Division II. The mining research group of Gecamines was given the task of designing a mining geometry then testing this design in a full scale test. Based on an evaluation of the faulting and fracturing of the 2 parallel orebodies and on an extensive in situ testing program preliminary mathematical analyses were used to develop and evaluate room and pillar designs in the 35°-65° dipping bedded formations. Based on these analyses and the constraints of having to fit the design of Division II to grade into Divisions I and III in a logical manner, a mining geometry for Division II evolved. To test this design an instrumented room was excavated in the most critical area. The results of this full scale testing showed that the behavior of the roof and wall rocks were as had been predicted by finite element computer model studies which incorporated the material properties and results of the field testing. The room geometry design was both judged and observed to be stable, hence mining commenced.

Jan 1, 1977

By Robert Snow, Francisco Sotillo

Six types of amines were evaluated in the cleaning step of the rougher concentrate for the Crago “Double Float” process in terms of relative selectivity. Selectivity of these amines was ranked based on both batch and locked cycle flotation tests. Two parameters were used for selectivity ranking, the Selectivity Index, SI, and the ratio of insol rejection to the tailings weight percentage, R*. The comparison of the flotation results of the batch tests of the cleaning step of the Crago process for an unsized amine feed generated the following ranking from the most selective to the least selective mine: Quaternary > Primary [ ]Tertiary [ ] Condensate > Ether > Secondary(?).

Jan 1, 2002

By R. G. Robins

The dissolution of metallic copper powder in aqueous solutions of cupric sulfate with ethylene under low pressure was investigated. The reaction stoichiometry obtained was:

Jan 1, 1988

By Colin J. Booth

Hydrogeological impacts of active longwall mining were studied at two sites in Illinois. At the site with the more transmissive sandstone aquifer, aquifer permeabilities increased an order of magnitude due to subsidence. Piezometric levels declined with subsidence due to increased porosity, and ahead of mining due to a transmitted drawdown. Levels recovered rapidly at first and fully over two years. At the site with the less transmissive aquifer, impacts were similar except that recovery has been limited. Local aquifer enhancement through increased yield can occur, but only where the aquifer is transmissive enough for recovery.

Jan 1, 1986

By Y. T. John Kwong

Modified after procedures for assessing acid-generating potential of coal spoils, most acid-base-accounting (ABA) analyses inadequately characterize highly varied metal deposits. Although mineralogy critically controls acid generation and metal leaching, acquisition of appropriate data and their interpretation are poorly developed. Metal loading rates are commonly determined by kinetic testing, which rarely duplicate actual field samples and conditions. Accurate predictions and reduced assessment costs can conceivably be achieved by (i) use of geochemical analyses to define surrogate indicators; (ii) intelligent acquisition and use of mineralogical data; and, (iii) compilation of geo-environmental ore-deposit models to validate inference based on detailed geology.

Jan 1, 2000

By R. J. Clements

The waterway transportation system in the united states consists primarily of the Mississippi river system. With its navigable tributaries, it is 12,500 miles long. This system naturally accesses about 40 percent of the nation. With its connecting railroads and highways, the river system accesses the united states from the Appalachian mountains in the east to the rocky mountains in the west. Within this area is the vast majority of our agricultural, industrial and material resources.

Jan 1, 1984

By Murali M. Gadde

Perimeter mining is a special form of very productive partial extraction method practiced at some mines in the United States. In the Illinois Basin mines where all major coal seams have weak underclay in the immediate floor, experience shows that any long-term ground control issues will arise due to floor failures rather than instability of the coal pillar itself. While there is a significant amount of work done on floor stability associated with regular pillars, no work has been done so far on the stability of perimeter pillars. This paper reports the results of a comprehensive study that was conducted for the first time on floor stability during perimeter mining in the Illinois Basin mines. A special plate template, which mimicked a common perimeter pillar configuration was created to conduct in-situ bearing capacity tests at five mines in three states of the Basin. Additionally, because of the complex shape of pillars created in perimeter mining that defies any closed-form solution, floor bearing capacity was studied using three-dimensional nonlinear numerical modeling. Based on these in-situ and numerical studies, some guidelines are provided for perimeter pillar stability analysis.

Jan 1, 2009

By R. L. Grayson, L. L. Probert

A three-year project focusing on the depth profiling of respirable coal mine dust particles using scanning electron microscopy coupled with energy dispersive X-ray analysis resulted in the development of statistically classified particle-behavior models. The models depict the changing silicon fraction for particles at 5-, 7-, 9-, and 11-keV accelerating voltages, thereby giving a clear indication of the nature of various types of mineral particles. This paper focuses on the results for respirable quartz particles sampled from five underground coal mines across the US. Through statistical analysis of results the relationship between the fraction of surface available quartz in respirable dust samples and coal rank is established for three Pennsylvania coal seams.

Jan 1, 1995

By R. S. Sheeta, C. J. Bise

The search for a more effective means of coping with methane liberation has resulted in the expanded use of seam degasification. Its advantages are measured not only in reducing the hazards due to methane, but also in producing a marketable commodity, the gas itself. However, the success of a methane drainage system is the culmination of many complex factors, the most important being the coal seam permeability. The two most popular drainage techniques used in mining today are the vertically stimulated borehole method and the in-seam horizontal borehole method. The objective of this paper is to determine the permeability range in which the selection of the degasification technique is based primarily on equipment and economic analysis. A discussion of the equipment involved will be incorporated into examples evaluated by the Pennsylvania State University coal methane simulation model.

Jan 1, 1990

By J. A. Cole

Santa Fe Pacific Gold's Lone Tree mine is located in Humboldt County, NV, 45 km (28 miles) east of Winnemucca. The mine currently operates a 1.74-Mt/a (1.92-million stpy) run-of-mine heap-leach operation and a 2.27-kt/d (2500 stpd) refractory gold¬ore-processing plant. Most of the mill-grade ore reserves are refractory, mainly due to pyrite and arsenopyrite encapsulation of the gold. The autoclave pressure-oxidation circuit was commissioned in February 1994 to process the refractory ore. Mineralogy unique to the Lone Tree deposit allowed for the design of a partial-oxidation process. It takes advantage of the heterogeneous nature of the pyrite morphology. Partial oxidation has resulted in an autoclave plant that is able to achieve low operating-unit costs (Figs. 1 and 2).

Jan 1, 1995

By S. H. Advani, J. K. Lee, K. S. Chan, J. M. Avasthi

A summary of field equations governing the hygro-thermo-mechanical (coupled temperature, moisture, and stress) response of geological media is presented. The applicability of these equations, with appropriate boundary conditions, to the study of basic mechanisms associated with underground coal gasification (UCG) process is discussed. In particular, the phenomenon of stress-induced spalling resulting from intense drying near the gasified cavity and in situ effects is investigated by means of the finite element method. Some typical results from sample finite element model representations are presented for the evaluation of field experiments.

Jan 1, 1986

By N. Magdalinovic

This paper analyzes the basic elements important for sustainable development in the sphere of metal mineral raw materials and offers one of the possible ways of defining the index of sustainable development.

Jan 1, 2007

By Guillermo P. Salas

The Consejo de Recursos Naturales No Renovables of the Mexican government entered into an agreement with the United Nations in 1964 for the mineral exploration of a large area in Estado de Sonora, Mexico. The agreement called for a systematic exploration for copper in northern Sonora based on photogeologic mapping, aerial reconnaissance, and geochemical stream sediment sampling. The UN-CRNNR investigations resulted in the detection of anomalous copper values in sediment from the Arroyo Cruz de Cafiada. The anomaly was followed upstream to its source, which ultimately proved to be the La Caridad ore body (see Fig. 1). Soil copper and molybdenum values were found over a large area, and further detailed geologic and geophysical investigations were instituted of the anomalous area. David Coolbaugh was largely responsible for the follow-up work. An induced polarization (IP) survey found a roughly circular region of "highs" that coincided with a high soil copper anomaly. The circular anomalies ringed the topographic feature that ultimately was found to contain the Caridad ore body. Soil geochemical copper response over the ore body was subdued, because the soils were derived from a leached capping, whereas leaching in fringe areas that contained less veining was less intense. The ore body was also ringed by the typical high pyrite zone, and this was the anomaly detected by the IP survey. The UN began drilling in the fall of 1966. Eleven holes tested the IP-Cu geochemical high, but none were of commercial interest. The project was returned to the Consejo and was reviewed in the field by G.P. Salas and V.F. Hollister. It was found that the leached capping had not been tested by the past activities, and the Consejo elected to explore that area in 1967. The capping was evaluated by Salas and Hollister and drilling by the Consejo began in 1967. Commercial grade ore intercepts were found in the first hole. The Consejo drilled nine holes, of which eight were commercial. At least 90.7 Mt (100 million tons) of 0.8% copper were indicated by the Consejo in eight holes. The lesson learned in this discovery is that evaluation of leached capping is an important guide to exploration. The general-

Jan 1, 1991

By S. Chunhui, W. Anbin, R. B. Cook

The Xicheng is one of China's largest lead-zinc (Pb-Zn) districts with known minable reserves in excess of 10 Mt (11 million st). The centrally located Changba-Lijiagou and nearby deposits are representative of the district. They consist of stratiform and stratabound zones of pyrite-sphalerite-galena mineralization within deformed, moderately metamorphosed Middle Devonian clastic and carbonate units. When considered with other similar districts that extend for several hundred kilometers to the east, a major episode of Devonian sedimentary exhalative mineralization is indicated.

Jan 1, 1992

By K. S. Shivakumar, R. Bhima Rao, M. R. Patil

Liberation size can be estimated using various techniques such as grain counting, frequency curves, X-ray intensity and the mesh of grind. The present investigation deals with the estimation of the liberation size of graphite flake contained in a schistose ore from Shivaganga, India. It was observed that the flakes are liberated at from 75 to 150µm. The rougher flotation concentrate obtained after grinding the run-of-mine ore for 5 min contained 54% fixed carbon. This represented the first stage of liberation. After regrinding to <90 µm in the presence of sodium silicate and guar gum, a cleaner concentrate containing 82% fixed carbon was obtained.

Jan 1, 1998

The absence of coal face particle management practices heavily penalizes coal transportation from initial loading to final consumption. Penalties include dust problems, significantly reduced mine loading cycle productivity, mine belt spillage, excessively high coal preparation costs and chute and dangerous pulverizer blockages at the final point of utilization. The common environmental and economic enemy is fines. Everyone knows that fines cause safety and environmental dust problems, but few understand that fines also swell broken coal to a point where 5 to 15 percent more time and capacity must be used to deliver the same tonnage. In this paper, methods and rewards for reducing and/or managing fines at the mine face are discussed. Computer-based loading cycle model productivity estimates, viewed from a new perspective, are made on the basis of material volume rather than on the long established and frequently misleading basis of tonnage. After all, it is typically the volume of broken material being transported that defines the capacity of a given transportation system, while the corresponding tonnages are merely a reflection of the specific material densities. Published evidence suggests that the swelling of broken coal can be decreased very significantly using small quantities of certain non-frothing chemicals added to mine face spray water and/or by employing improved mine face breakage practices. In a future paper, the effects on transportation productivity beyond the coal mine will be discussed.

Jan 1, 1994

By H. Tutu

The legacy of gold mining operations continues to affect water quality in the Witwatersrand Basin in South Africa. The acid mine drainage (AMD) emanating from the tailings dumps liberates heavy metals from the ore minerals. The objective of this study was to characterise the geochemical processes that are important in understanding chemical evolution of polluted water in the study area. Analytical results for water samples collected in the catchment of the study area generally showed elevated concentrations of heavy metals in the vicinity of tailings dumps and mining operations and a decrease in the distal. Dams and wetlands, despite their proximity to the tailings dumps, recorded low concentrations of heavy metals and other pollutants. The characterisation of AMD was summarised in a conceptual model in which plots of redox potential versus pH and electrical conductivity versus pH were identified as the most important sub-models that captured the gross physical-chemical characteristics of polluted water and its interaction with the environment.

Jan 1, 2006