Search Documents

By Dan Nilsson

INTRODUCTION There are many mine planning factors in sublevel caving, as in the other mining systems, which when varied can substantially alter mining costs and profit¬ability. In this chapter, the following four topics are addressed with regard to economic optimization of sub¬level caving: production planning, haulage level spacing, orepass spacing, and extraction cutoff. The costs used here are the right order of magnitude but since each mine is unique, they should be considered only as examples. The objective is to demonstrate the tech¬niques which can be used. In a real mine, the evalua¬tions must be done using actual costs and conditions. It is difficult to predict exactly the costs involved, and therefore it is valuable to perform a sensitivity analysis to evaluate the effect of making incorrect as¬sumptions. Since the mining industry is very capital intensive, the effect of the interest rate must also be studied. PRODUCTION PLAN FOR AN IRON ORE DEPOSIT Introduction The first and most important thing to do before de¬signing an underground mine is to establish a long-range production plan. Such a plan is necessary for all eco¬nomic evaluations and should provide information about the lifetime of the mine, how much ore and waste must be handled per year, how much development per year is required, etc. An example is given in the following section. Problem In an iron ore mine sublevel caving is used. The iron content is 42%, and the mine supplies a pelletizing plant with an annual capacity of 3 million t/a. The ore body is shown in Fig. 1. The length of the ore body is 1000 m and the width is 100 m. Each slice is 10 m high, and there are 10 m be¬tween crosscuts, each of which has an area of 20 m2. The density of the ore is 3.5 t/m3. The spacing between rings is 2 m, and the extraction is 100%. The iron con¬tent is 66% in the pellets and 6% in the tailings. The problem is to develop a detailed production plan. A typical sublevel caving sequence is shown in Fig. 2. Solution Amount of ore per meter of crosscut: 20 X 3.5 = 70 t. Number of crosscuts per slice= 100. Length of crosscuts per slice: 100 X 100 = 10 000. Ore from crosscuts per slice = 10 000 m X 20 m2 X 3.5 = 700 000 t. Number of sublevel caving rounds per slice: 10 000/2 = 5000. Area for each blast in sublevel caving: 10 X 10 - 20 = 80 m2. Amount of ore per blast: 80 m2 X 6 m X 3.5 = 560 t. Extraction: 100% (see extraction curve Fig. 12). Loaded ore per blast: 75% or 420 t. Loaded waste per blast: 25% or 140 t. Total: 560 t. Total amount of rock from each blast in the sublevel caving: Ore: 560 t of which 2 X 70 = 140 t from develop¬ment work and 420 t from sublevel caving. Waste: 140 t. Total: 700 t. The ore needed per year is 3 X (66-6)/42-6 5 mil¬lion t. Necessary number of blasts per year= 5,000,000/ 560 = 8929. Distance to develop per year = 8929 blasts per year X 2 m per blast 17 858 m. Total amount/year: Ore from development work 17 858 m x 70 t/m = 1.25 million t/a Ore from sublevel caving: 8929 blasts per year X 420 tons per blast = 3.75 million t/a 5.00 million t/a Waste rock dilution: 8929 blasts per year X 140 tons per blast 1.25 million t/a Total amount to hoist 6.25 million t/ a The amount of ore from development work will in¬crease a little if the horizontal drift is placed in the ore body and not in the footwall. In this example the ore loss in 20%, and the waste rock dilution is also 20%. After taking the ore loss into account, the lifetime for 100 m of the ore body will be:

Jan 1, 1982

By Peter T. Luckie

Coal represents 80% of the fuel reserves of this country, yet only 20% of the fuel consumption. In order to change this ridiculous situation, a realistic coal utilization roadmap needs to be drawn to show how we go from where we are to where we want to be. The completion of the roadways will require the building of research bridges. The research bridges on the coal processing section of the superhighway should be built to process 500pm by 100pm rather than 25pm by 0 raw coal . Particular emphasis should be on middlings processing and total plant performance. The superhighway should be layed out by a team of fuel, coal preparation and mining engineers.

Jan 1, 1988

By M. E. Poad, W. G. Pariseau, M. A. Laurenti

In 1986, a cooperative effort by Homestake Mining Co., the US Bureau of Mines and the University of Utah was initiated to determine shaft stability while recovering high-grade ore in a nearby pillar. Premining finite element simulations indicated the shaft would remain in elastic ground. Six years have elapsed and, despite some initial concern during the first lifts, it appears that the bulk of the original reserve will he safely and profitably recovered. An integrated application of rock mechanics tools from laboratory testing through numerical modeling to mine measurements and observations contributed substantially to the operational success of the project.

Jan 1, 1996

By Wern-ping Chen, Joseph Pratt, Thomas G. Brueckner, Tracy K. Lundin

To address and mitigate discharges from combined sewer overflows in the Providence, Rhode Island area, the Narragansett Bay Commission completed a comprehensive Combined Sewer Overflow (CSO) Facilities Plan in 1993 which included a series of deep rock tunnels. Since completion of preliminary design of the program in 1994, the program has been reconfigured in response to the Environmental Protection Agency’s (EPA’s) new CSO policy. The currently proposed system consists of a deep rock tunnel with two tunnel stubs which will provide230,000 cu m (62 million gallons) of storage at depths of up to 90 m (300 ft). This paper discusses the revised 5 km (3 mile) long deep tunnel system.

Jan 1, 1999

By Janine L. Beazley, James H. Kyle

The effects of pH, pH modifier (lime or caustic soda) and cyanide on the pulp rheology of a number of ore types ranging from highly siliceous to highly kaolinitic has been investigated. All experiments were performed in fresh water at solids concentrations of 25 and 45% solids and in the pH range 6 to 11. The kaolinitic ores exhibited greater changes in rheology with pH and calcium ion concentration than did the siliceous ores.

Jan 1, 1989

A number of factors affecting the properties of cemented aggregate fill (CAF), particularly its strength development have been studied through a series of laboratory investigations carried out at the Western Australian School of Mines in the Western Australia in recent years. The outcomes of these investigations indicate that apart from cement dosage, aggregate particle size distribution, aggregate quality, additional fine materials, water salinity, admixture dosage and sample scaling all contribute significantly to the development of cemented aggregate fill strength.

Jan 1, 2001

By Dave Rogstad

The DART NC-1B Tunnel Project consists of two 5,100 m TBM excavated tunnels, a principal underground station, a partially completed future station, a surface station, and eight associated ventilation shafts and exit tunnels. This paper presents a case history of the project's construction, and will focus on six topics that give this project a unique and unusual history; the TBM excavation, two major differing site conditions, roadheader excavation, polyfiber reinforced shotcrete lining, the NATM design geometry, and a design/build type of contract.

Jan 1, 1995

By Scott F. Andersen

Discussion to include location and description of the project from upper lake through powerhouse to lower lake, noting locations and size of shafts. Discuss evolution of shaft development concepts in conjunction with owner, contractor and CAL OSHA. Discuss elevator shaft equipment, T1 gate shaft, T2 surge shaft equipment, T3 surge shaft and the incline shaft equipment. Question and answer period.

Jan 1, 1981

By Lynn B. Hales, Randy Ynchausti

Expert systems are now being used effectively to streamline and improve the performance of supervisory computer control strategies. Their advantages have led to use in both batch and continuous applications. Expert systems in the context of real-time process control, will be defined and examples of their successful implementation in autogenous, semi-autogenous and ball mill grinding circuits will be discussed.

Jan 1, 1990

By Edward S. Plotkin, Thames F. Peyton, Gary A. Almeraris

This paper describes high speed tunneling by drilling and blasting in a heavily populated urban area. The project consists primarily of mining 2500 m (8237 ft.) of tunnel through mica schist, excavating three shafts approximately 200 m (650 ft.) each and concreting lining 5300 m (17,400 ft.) of 7.34 m (24 ft.) inside diameter tunnel. The techniques developed and equipment utilized to ensure a high rate of tunneling advance are described. Extensive planning and good communications were especially essential in maintaining production on this project since tunnel mining, tunnel concreting, and shaft excavation all proceeded simultaneously from one common work shaft and a single heading.

Jan 1, 1985

By Jerry Harrington, Brad Wigglesworth, David C. Beling

Commercial operations at the open pit, heap leach Crofoot Mine commenced in April, 1988. Approximately 13,600 tonnes (15,000 st) of low grade pregnant solution are treated daily using a Merrill-Crowe circuit. Acceptable gold recoveries from these low grade solutions can be obtained by optimizing solution pre-treatment prior to zinc addition.

Jan 1, 1990

By Scott G. Britton

This chapter is concerned with the construction of the dynamic component of belt haulage systems. The dynamic system includes the belt line and tailpiece extension and retraction movements in a production system where mine management is continually placing the belt in the most effective operating position. Correct installation of the belt and tailpiece during an extension is very important for many performance reasons. Two of the most important reasons are to eliminate spillage and safely operate the belt line. This chapter is divided into three major discussions. The first discussion looks at analyzing the parameters of effective belt line construction. This includes a review of the parameters and management tools needed for proper scheduling of a move-up. The second major discussion topic centers on efficient procedures for a belt line extension. Topics such as site preparation, tailpiece breakdown and setup, stringing the belt line and structure, plus operating and maintenance tasks needed after the belt line is installed and running, are covered. The third discussion presents a list of conveyor and conveyor component manufacturers who provide services and products to the coal mining industry. Again, any discussion on underground haulage systems must generalize much of the site specific design approaches to be practical. This text will mention, where applicable, some of the alternatives available to construction engineers in designing belt line systems.

Jan 1, 1983

By Terry I. Mudder, Michael M. Botz

Discharge regulations for mine waters require relatively low concentrations for cyanide and metals, and the trend is for discharge limits to be lowered. In the event conventional treatment practices are not sufficient to meet discharge limitations, advanced treatment technologies such as ion exchange and reverse osmosis may be considered. Though these technologies will provide discharge quality waters, they also require the disposal of a concentrated brine and are relatively complex and costly to operate. Many mine sites currently using activated carbon in precious metals recovery present the opportunity to economically operate an activated carbon water treatment plant for polishing of effluents. This paper presents summaries of six ( 6) mining operations which have evaluated or use activated carbon for treatment of water and which also use carbon in precious metals recovery processes.

Jan 1, 1997

By Glen L. Black

Choosing a mining method for an underground orebody is a complicated and often iterative process. Advances in technology have given design teams an array of possibilities for methods and equip¬ment. Hecla Mining's discovery of the deep Gold Hunter ore body challenged the staff at the Lucky Friday Mine to determine the optimum mining method. Taking an ore body from prospect to production requires traditional resource characterization. This includes drilling, delineating and modeling. Developing the mining plan is an evolving process, changing with each new piece of in¬formation as the project progresses through exploration and development. The Gold Hunter deposit is a steeply dipping vein system in the Wallace Formation of Idaho's Coeur d'Alene mining district. Gold Hunter is a misleading name for the ore body. The vein is a silver-rich, lead-zinc deposit with only traces of gold. The Gold Hunter ore body is located about 1.6 km (1 mile) north to northeast of Mullan, ID. The ore body is mined from the Lucky Friday Mine, located 0.4 km (0.25 miles) east of Mullan. Mining began on the vein from an access drift driven from the Lucky Friday Mine's 4900 level. Production from the ore zone is projected to be 771 t/d (850 stpd). The Gold Hunter ore is combined with Lucky Friday ore and milled in the Lucky Friday mill. The combined ore boosted Lucky Friday's 1998 silver production from 62.2 t/a (2 million oz/year) to more than 124.4 t/a (4 million oz/year).

Jan 1, 1999

By E. Suoninen, K. Laajalehto, L. Kartio

Efficient separation of pyrite from other sulfides is of great importance for the metallurgical performance of flotation processes. In this work Fourier Transform Infrared Spectroscopy (FTIR) and X-ray Photoelectron Spectroscopy (XPS) were used to study the surface chemistry of pyrite in depression, activation and xanthate adsorption under conditions of controlled potential. Modifications of pyrite surfaces after treatment with depressants (lime, sulfur dioxide, sodium cyanide) and after activation with metal ions (Cu, Pb) were studied. The principal adsorption product identified on pyrite was dixanthogen whose formation started at about +0.15 V and +0.25 V (vs, SHE) in ethyl and amyl xanthate solutions, respectively. Copper xanthate was formed on copper(II) activated pyrite. Activation mechanism of pyrite by copper(II) salts is likely to be electrochemical where copper occurs as copper(I) on the surface of pyrite. Effective depression is achieved by sulfur dioxide and sodium cyanide. Depression at high pH is due to formation of iron(III) hydroxides. Calcium ions do not affect the electrochemistry but adsorb on pyrite and reduce the surface sites for dixanthogen adsorption.

Jan 1, 1995

By W. A. Niepelt, F. A. Locher

Flow in steep cascades may lead to the occurrence of a nearly periodic train of waves known as slug flow. This, in turn, may result in overtopping of the channel walls and problems with energy dissipation in receiving sumps. Experimental data from an operating facility was used to extend clear water technology for predicting the occurrence of slug flow to conditions with slurry flows. A design methodology and a design chart to determine the region of steady flows is presented that will permit the design engineer to avoid slug flow in cascade systems for conveyance of slurries.

Jan 1, 1990

By R. D. Miller, D. W. Steeples

Seismic reflection is a powerful geophysical exploration method that has been in widespread use in the petroleum industry for more than 60 years. This paper addresses some basic principles of the method and its application at depths shallower than 30 m (100 ft). Since 1980, the shallow reflection technique has been increasingly used for engineering and environmental problems, such as mapping bedrock beneath alluvium and delineating intra-alluvial features near hazardous waste sites, detecting voids in coal and karst, defining the top of the saturated zone and mapping shallow faults. New applications will be added with improved resolution and increased cost-effectiveness.

Jan 1, 1994

By F. F. Aplan, D. D. Xu

A novel system for the depression of pyrite and the ash-forming minerals has been developed. A metal ion, including but not restricted to Fe+2, is added to form a hydroxide coating on the pyrite or ash-forming minerals. A polymeric depressant is then added to attach to these re- surfaced minerals. Nearly 200flotation tests with I1 different coals indicate the effectiveness of this system. Many of the important process variables such as the coal source, frother- collector system. grind size and procedure, pH, metal ion, and depressant type and concentration have been studied.

Jan 1, 1995

By E. Sehner, G. Van Weert

Metal chloride pyrohydrolysis is a fifty year old technology, operating satisfactory in many plants around the world, mainly on ferrous chloride, The capabilities and costs of its two equipment options (spray roaster and fluid bed pyrohydrolysis) are well known. Why is the technology not more widely used in mineral processing, beyond the production of MgO and upgraded TiO2slag? After briefly reviewing chloride vs. sulphate process characteristics and existing plant operations, this paper will discuss pyrohydrolysis options for the mine developer using the processing of ilmenite, siliceous zinc oxides and oxidic nickel / cobalt ores as examples.

Jan 1, 2003

By Shelley M. Burg, Dennis K. Poulton, Robert B. Gordon

This project includes the excavation and concrete lining of approximately 18 900 m (62 000 ft) of 5.5 m (18 ft) finished diameter subway tunnel for the Los Angeles MTA. The project required that four soft ground headings be excavated from a single shaft located near the mid point of the tunnels. The tunnels were classified "gassy" during the excavation phase. Because of the contract schedule requirements and the limited urban work site available, many logistical problems had to be overcome during the project while excavation was accomplished at a record setting pace. Some unique project features include the muck handling system and an access shaft using a high strength tieback support system. In order to accomplish the work, an extensive effort to plan and construct the main work site was required.

Jan 1, 1995