Search Documents

By N. L. Anderson, R. Ramananantoandro, F. Wirnkar

Six-fold, high-resolution, compressional-wave seismic data were acquired across a coal mining property in the Meigs County study area, southeastern Ohio, with a view to differentiating the Clarion Coal Member and a truncating channel sandstone prior to longwall mining without costly drilling. The seismic technique, as is illustrated by our example data, was successfully used to map those areas where the coal is present, as well as those places where it was eroded by incising fluvial streams. Our results demonstrate that the seismic reflection method, using an engineering seismograph, can be a cost-effective way to define discontinuities associated with coal seams.

Jan 1, 1992

By L. A. Arrington-Webb

Forty-four states produced clay products during 1994 for a total value of $1.6 billion. This was a 3% increase in total tonnage and a 7% increase in value from 1993. Kaolin Domestic production of kaolin during 1994 was estimated to be 9.3 Mt (10.2 million st), according to the US Bureau of Mines (USBM). Georgia remained the leading producer with 7.5 Mt (8.2 million st), followed by South Carolina with 535 kt (589,000 st). Kaolin used as a paper coating or filler pigment accounted for 51% of domestic consumption. Other uses included grogs (14%), fiberglass (5%) and plastics (4%). A reclassification by an Alabama producer of fire clay to kaolin accounts for the introduction of kaolin used in grogs. This also accounts for the apparent decrease in the use of kaolin in paper from 60% in 1993. However, the actual amount of kaolin used in paper was the same.

Jan 1, 1995

By Hervé Le Bissonnais, Jean-Pierre Janin, Anne Bergère, Pierre Renier

"The most important impact on the environment of a tunnel excavation is the creation of surface settlements. Nowadays, the mechanized tunneling allows minimizing the settlements, applying a confinement pressure which counterbalances the ground de-confinement. It is thus essential to determine the correct amount of confinement pressure. In this paper, the authors present a 3D numerical study simulating the EPB-TBM excavation of a water tunnel, in the Flanders clays (north of France). Firstly, a simplified 3D simulation, based on the concept of instantaneous longitudinal settlement curve, was performed to predict the surface settlements for different values of heading confinement pressures. Secondly, the same pressures were tested by the EPB-TBM in a monitoring zone. The comparison between the prediction settlements and the measurements was very satisfactory and allowed validation of the numerical approach and the choice of the optimal confinement pressure value for a sensitive area of the project. INTRODUCTION The excavation of a tunnel can create displacements of the surrounding soil which may affect existing structures and generate unacceptable dysfunction. The development of the closed shield tunneling has permitted to reduce the volume loss generated around the excavation and consequently the surface settlements. In this case, as explained by different authors (Clough et al., 1985; Kastner et al., 1996; Mair and Taylor, 1997), the ground movements are influenced by the TBM works: the heading confinement pressure, the shield overcutting and conicity, the annular void grout injection parameters, the segment concrete lining rigidity, the consolidation of the grout. Hence, in the tunnel design, it is important to take into consideration these different processes of the excavation works to simulate correctly the tunneling process."

Jan 1, 2016

By V. Y. Kirillin, V. A. Rumjantsev, S. A. Tchesnokov, Yu A. Veksler, V. F. Kalmykov, A. N. Telgarin, A. T. Shakirov

Mining in outburst hazard seams may be safe and effective if some preventive measures, such as lowering gas and rock pressure as well as speed regulating of a continuous miner in cutting the seam would be practised. The driving speed should be optimal as the low speed lowers labour productivity but the high speed may cause gaso-dynamic phenomena. At this mine the driving speed is regulated by seismo-acoustic control of the seam condition.

Jan 1, 1985

By Harry Sutcliffe, Francis M. Keville

The paper describes the, impact of the geotechnical exploration program on the line and grade of the tunnels and the shaft configuration on the Red Line Extension N.W. in Cambridge and Somerville, Massachusetts, and comments on several aspects of the implementation of the project.

Jan 1, 1983

By John H. Fowler

The 30th Forum on the Geology of Industrial Minerals will be held in the historical seaside city of Halifax, Nova Scotia, from May 22 to May 27, 1994. The Forum will be co-hosted by the Provinces of New Brunswick and Nova Scotia, two of Canada's East Coast Provinces, both having a long tradition of industrial mineral production. Two previous Forums, the 19th in Toronto in 1983 and the 27th in Banff in 1991, offered delegates the opportunity to see industrial minerals in central and western Canada. The 30th Forum will take you to Canada's east coast completing the picture of Canada's industrial minerals from coast to coast.

Jan 1, 1995

By S. K. Nandy, K. F. Unrug

The behavior of the immediate shaly roof within a drift mine in eastern Kentucky, operating in the Coalburg seam, was monitored with roof bolt dynamometers. The dynamometers used were capable of providing readings up to a maximum load of 66.72 kN (15,000 lbs), + 0.022 kN (5 lbs). To observe the influence of moisture on the rate and extent of roof deterioration, 57dynamometers were installed on roof bolts anchored in intake and neutral airways. Monitoring was conducted during the period January 1985 through January 1986, in order to cover a full cycle of dry and wet mine conditions associated with seasonal changes. Analysis of the data showed a trend of roof deterioration induced by condensation and eventual penetration of moisture within the immediate roof bedding planes, leading to rapid disintegration of the mine roof.

Jan 1, 1987

By W. D. Presley, T. R. Harrell

This paper will be a case history of the shaft and tunnel concrete lining techniques used at the Rocky Mountain Pumped Storage Project located in northwest Georgia. Emphasis will be placed on the shaft lining techniques with only a brief description of the tunnel concrete lining techniques. The 10.67 meter (35 foot) diameter shaft and tunnel concrete linings are 0.61 meter (2 foot) nominal thickness with a single row of reinforcing bars. The tunnel was placed in 18.29 meter (60 foot) lengths with bulkheaded end sections. The 172.72 meter (566.68 foot) vertical shaft was placed in 3.05 meter (10 foot) high sections using jump forming techniques.

Jan 1, 1985

By Xu Xiaohe, Zhou Jiandong, Luo Shihui, Zhang Liqun

Recently, the research and applications of ES (Expert Systern) have been put forward actively in many mining fields in China. After various ES applications or instances are introduced, the paper has especially focused on the exclusive properties of a mining system different from any other system and the problems of the existing mining ES applications. And a synthesis methodology has been introduced in order to develop a applicable ES application

Jan 1, 1996

By Steve Kral

Americans are taking a more critical view of various environmental laws because the effects of those laws are becoming more pervasive and intrusive, according to William Perry Pendley. And Secretary of the Interior Bruce Babbitt is seemingly so unpopular in the West, he no longer campaigns there for Clinton Administration policies. Pendley is president and chief legal officer of the Mountain States Legal Foundation, a public service, non-profit law association that takes on property rights cases for people who cannot afford representation. He was one of the luncheon speakers at the 101st Northwest Mining Association meeting, held in Spokane, WA in early December.

Jan 1, 1996

By J. B. Yianatos

This paper addresses the impact on performance of column height (H), and column height to diameter (H/D) ratio by modelling the effect of HID on mixing and consequently on recovery and grade. Mineral recovery increases with increasing H/D ratio for a constant column volume and feed flowrate, while the concentrate grade decreases to a minor extent. Columns 10-15m in height with H/D-10 are well suited for feed rates 150-600 L/min. Maximum H/D is determined by the gas carrying capacity, an important consideration for pilot units where H/D?200.

Jan 1, 1987

By Lynn B. Hales, Randy Ynchausti, Jeffrey D. Mckay

Many consider rougher flotation control to be more of an art than a science. Some have even thought it impossible to make process control decisions and changes without human interaction. Controlling flotation bank pulp levels to maintain consistent pulling rates in the face of changing feed slurry flow rates, varying mineral types, and inconsistent reagent additions can be daunting. However, an advanced supervisory control strategy was installed on the plant floor to control an industrial rougher flotation circuit with little or no operator interaction. Plant staff monitored the flotation circuit under supervisory control and reported benefits of up to 4% improvement in copper recovery above that achieved with an older supervisory control strategy. To accomplish this work, a novel use of instrumentation to solve a flotation bank pulp level control problem was employed, a new implementation approach was used to correct some flaws in the older approach, and careful attention was paid to a few key process control principles. This paper discusses important aspects of these activities.

Jan 1, 2000

By Jerry R. Johanson

Introduction Many solids processes that look feasible on paper or even in pilot studies become disasters in full scale. Changes in solids flow characteristics from pilot scale to full scale be- cause of larger solids contact pressures, thermal shocks, or unforeseen temperature excursions often cause full-scale solids flow problems not encountered in the laboratory or pilot studies. Fortunately, proper applications of solids flow principals and solids flow properties measurement at full scale conditions can anticipate the problems and thus provide an accurate basis for full-scale design or existing plant modifications. Solids flow properties The basic solids flow property definitions are given in Table 1 (Johanson, 1966, 1976, 1978, 1985). In this section, the author will discuss each property and its potential for creating full-scale pilot plants. Unconfined yield strength The unconfined yield strength of a bulk solid determines the tendency for cohesive hangups of the solids in the process and is effected by the time at rest, chemical reactions, temperature, liquid content, solids size consist, and phase changes of solids or fluids involved in the process. One of the common mistakes is to consider the solids condition only at the beginning and the end of the process. For example, consider the direct reduction of iron ore. The feed solids are free-flowing, hard lump ore or pellets. The end result is a hard, free-flowing reduced sponge iron lump or pellet. One might conclude that the process involves free-flowing lumps. This conclusion may seem reasonable based on laboratory studies oreven pilot plant studies where solids contact pressures are very low. Unfortunately, during the reduction reactions at high temperatures, the rock or pellets soften and, with solids contact pressures associated with the full-scale plant, may fuse together, thus providing a possible solids hangup in the moving bed reactor not evident in the low pressure pilot scale. Fig. 1 shows some typical unconfined yield strength measurements for pellets as a function of solids contact pressure at various times at rest. Note at low consolidation pressures, generally associated with laboratory or pilot plant studies, the pellets show no strength unless held at rest for an extended time. This will produce a very free-flowing condition in pilot plants that will not exist in the full size reactor.

Jan 1, 1990

By Steve Kral

In December 2013, the Colorado Department of Transportation (CDOT) completed the widening of the eastbound tunnel on Interstate 70 (I-70) from two lanes to three. Work on the westbound tunnel began earlier this year and is scheduled for completion in December. The Twin Tunnels project is located in the mountains about 55 km (35 miles) west of Denver. They were bored during the 1960s when I-70 was being built and became the main access to Colorado?s growing number of ski areas and the state?s Western Slope. Throughout the decades following their construction, traffic on I-70 continued to increase and now the tunnels have a major bottleneck. Com-mutes to and from the mountain resorts, particularly on weekends, have become long and slow. Adding a third lane through the tunnels will help alleviate the congestion. (A complete report on the project can be found in T&UC, December 2013, page 61.) Once the eastbound tunnel was completed late last year, CDOT authorized the funding to begin work on the westbound side. That made economic sense, as the equipment used on the eastbound tunnel needed to only be shifted across I-70 to begin work on the westbound side, rather than removing it in December and bringing it back in March when construction began on the westbound tunnel. Work on the westbound tunnel uses essentially the methods that were used on the eastbound tunnel ? removal of the existing concrete lining and using drill-and-blast methods for tunneling widening. The main difference between the two tunnels is that the westbound side requires more blasting on both ends to widen I-70 to three lanes.

By Jing G. Yen

When a solid-liquid mixture is conveyed through a pipe,' four hydrodynamic conditions may develop depending upon the properties of the transporting medium, the properties of the transported material, the properties of the pipeline and the flow characteristics. They are classified as homogeneous flow, heterogeneous flow, intermediate flow and saltation. Heterogeneous flow, which is the subject of the present analysis, occurs when solid particles are coarse, of high density, and the mean velocity of the flow is relatively low, such that the combination allows the establishment of a pronounced concentration gradient in the cross-section of the pipe. In this type of system the suspended matter does not change the rheological properties of the conveying fluid, and solid and fluid phases behave somewhat separately. In recent years much work has been directed toward gaining more insight into the hydrodynamics of heterogeneous flow (1,2,3,4,5,) However, almost all knowledge obtained is empirical in nature and limited in scope. Much effort has been extended to collect experimental information on the energy losses associated with systems of slurry flow (6-13) The work of Durand and Condolios(14,15) represents one of the most extensive experimentations in this field. Through systematic test runs, the effects of the major flow-parameters were studied one at a time. From the results, they concluded empirically that:

Jan 1, 1969

By Darrell V. B. . McClarty

In 1996, Rio Algom, Denison Mines and the Elliot Lake Research Field Station (ELRFS) formed a consortium to implement a regional environmental information management system (REIMS) for the Elliot Lake area in Ontario, Canada. ELRFS is an affiliate of Laurentian University in Sudbury, Ontario, The discovery of uranium in the Elliot Lake region in post-World War II led to the development of 12 mines and 11 associated mills between 1955 and 1958. During the late 1980s, declining world demand for uranium, combined with the discovery of high-grade uranium ore in other areas of the world, made the Elliot Lake mines uneconomical. As a result, all area mines ceased opera¬tions by the end of 1996. The eight facilities and three tailings management areas operated by Denison Mines and Rio Algom's five mining waste management areas contain 150 Mt (165 million st) of potentially acid-generating tailings. The areas cover 13.2 km2 (3,265 acres) and receive drainage from an additional 13 km2 (3,212 acres). The primary objective of the joint initiative was to implement a personal-computer-based, regional, environmental-information management system for managing historical data and ongoing environmental programs in the Elliot Lake region. The Elliot Lake consortium decided it needed an information system with an integrated, process-oriented and requirements-driven approach to collect and manage the environmental information. Following a study of environmental information management systems currently used by the mining industry, the consortium decided to base REIMS on the "Envista" product. This is a commercially available, environmental information management system marketed by Envista Technologies of Saskatoon, Canada.

Jan 1, 1999

By Sunny Schoone, Maximilian Getz, Felix Leaman, ELISABETH CLAUSEN

Hydraulic transport is commonly used in mining for moving particles or ore concentrates in pipes over long distances with a water stream. Control and monitoring of this process require sensor technology that can obtain relevant characteristics of the two-phase flow. This work investigates the acoustic emission (AE) technology for monitoring a hydraulic system with different sand concentrations, showing the strong relationship between friction behavior in the pipe and the measured AE signals.

Apr 1, 2023

By J. J. Fallon

Las Vegas is a place of many distractions. It is difficult for one to apply himself to sophisticated technical matters in the midst of gambling, liquor, scantily clad young ladies and the top entertainment available in the United States. But, I know that the men and women of SME are made of stronger stuff and will not be tempted by these things.

Jan 1, 1989

By Alex Harrison, K. Payne

Computer generated magnetic field reference signa- tures of steel cord belt splices are used to evaluate lay-up and fabrication irregularities of splices in operating conveyors. Used as a quality inspection tool, magnetic signature analysis is useful in auditing data collected by general non-destructive testing (NDT) consultants. The evaluation can detect irregularities that weaken a splice, as well as detecting signature changes that can be indicative of adhesion loss. The evaluation can be applied to any NDT data available from a variety of commercial sources, which means that independent review of critical splice data is possible.

Jan 1, 1996

By David B. McWhorter, John D. Nelson

INTRODUCTION The quantity of seepage that will be released from a tailings impoundment depends not only on the characteristics of the seepage control system, but also on the properties of the foundation soil or rock beneath the impoundment and the nature of the groundwater in the area. The interaction between various elements of the seepage control system and the influence the various characteristics of the site and impoundment have on seepage are the subject of this paper. The results of analyses are presented herein to indicate the nature and magnitude of the effect that the various factors will have on seep¬age losses. Analyses were conducted for a uranium mill tailings impoundment located in an area characteristic of many found in the western United States or Canada. A typical seepage control system consists of placement of either a clay or synthetic liner beneath the impoundment. In some cases an underdrain system may be placed on top of the liner to collect drainage from the tailings. The parameters that were varied in the analyses included those pertaining to the liner, underdrains and foundation strata. In general, it is shown that the seepage losses will vary in a complex manner depending on the interaction of the elements of the site and the seepage control system. As may be expected, the liner and underdrain systems have the most pronounced effect on controlling seepage. This paper deals with the quantity of seepage released from an impoundment However, the impact that seepage losses from an impoundment will have on the surrounding environment will depend on the rate at which contaminants will enter the groundwater and the nature of the groundwater flow itself. Consequently, when considering these results with regard to environmental impact they must be interpreted along with considerations of geochemical factors. MECHANICS OF SEEPAGE The mechanics of seepage and methods of analysis that were used will be discussed briefly herein. For a more detailed discussion the reader is referred elsewhere (McWhorter and Nelson, 1978, 1979, 1980). A general column through the impoundment was considered to be as shown in Fig. 1.

Jan 1, 1980