Search Documents

By I. J. Duckworth

Due to improved, stringent safety regulations, many modern road tunnels are statistically safer, per kilometer, than above ground roadways. However, the public perception and reaction in the event of a serious tunnel fire is very different to that associated with a surface incident. Vehicle fires in road and rail tunnels are recognized to represent an immediate and extreme danger to the patrons of those systems. Unlike workers in the mining and civil construction industries, the general public are neither trained nor equipped to fight fires or evacuate under deteriorating smoke conditions. Accordingly, for the majority of modern transportation tunnels the ventilation infrastructure is sized on the requirement to control the combustion products from worst-case fire scenarios and to provide a tenable evacuation route for the tunnel users. It is common for these same emergency ventilation systems to be employed, often in a reduced capacity, for other operating modes such as the dilution of pollutants during congested traffic conditions. This is one of the fundamental differences to mine ventilation, where primary ventilation systems are not typically sized based on fire scenarios. This paper presents an overview of the subject of fires in vehicular tunnels. This includes a brief history of major transportation tunnel fires followed by a discussion on the resulting legislation and standards that govern the design and operation of tunnel emergency ventilation systems. A summary is provided on the common criteria, theory, and design techniques that are employed during tunnel emergency ventilation systems design. Information is provided on fire detection and suppression, with a discussion on the growing acceptance of wet suppression as a means to mitigate major fires in road tunnels worldwide.

Jan 1, 2009

By Nic Arrieta

The Arimetco White Cliff Diatomite operation near Tucson, Arizona will be discussed and reviewed across the spectrum of geology, mineralogy, mining, processing and product attributes and market applications. Unique for the operation are the type, quality and the extent of the reserves and several product characteristics of the diatomite.

Jan 1, 1996

In parallel work, the cyanide/silver impregnated activated carbon system was studied for the purpose of developing an alternate cyanide removal system. It was found that free cyanide can be reduced from 20 ppm to below 10 ppb with a fixed bed of silver impregnated activated carbon, since such cyanide removal might be applicable to gold mill effluents, the investigation was extended to the cyanide/gold impregnated activated carbon (GIAC) system. Batch tests were conducted varying the gold content of activated carbon, carbon/CN ratio, stirring speed, pH of the initial solution, and the reaction temperature. The adsorption isotherm of cyanide/gold impregnated activated carbon system was also studied. The results of these batch tests show that the behaviour of the cyanide/GIAC system is very similar to the cyanide/silver impregnated activated carbon system variation of the gold content of the impregnated activated carbon has some influence on the cyanide adsorption rate. The latter is mainly increased, however, by increasing the GIAC/CN ratio. The activation energy was determined to be 3.12 kca1/mole (13.08 kj/mole) and the Au(CN)2 saturation at 194 µ M/g NORIT ROX O.B. The experimental results of reaction temperature and stirring speed show that the adsorption of free cyanide on such activated carbon is controlled by pore diffusion inside the activated carbon particle or by surface reaction. The adsorption isotherm follows the linear model and it is favourable for the cyanide/gold impregnated activated carbon system.

Jan 1, 1994

By Ruichen Ren, Xu Han, Caixia Li, Zengchuan Yue

In this paper, the size-density distribution of coarse middling coking coal (CMCC) with different grinding fineness and flotation concentrates was investigated. Then, the flotation behaviors and liberation characteristics of different size-density fractions in ground CMCC were analyzed, and the different size-density fractions were divided into five categories: mostbeneficial, secondary-beneficial, poorly liberated, insignificant-pollution, and serious-pollution. Based on the content of particles with different liberation characteristics, an evaluation index of the liberation characteristic of ground CMCC, namely, the liberation perfection index (LPI), was proposed. The results indicated that grinding changed the size-density composition of CMCC, which affected the flotation performance. Insufficient grinding and overgrinding were not beneficial to flotation. Insufficient grinding caused a higher content of poorly liberated particles and a lower content of most-beneficial particles. Overgrinding increased the content of serious-pollution particles and reduced the content of most-beneficial particles. The size order of the LPI values of different ground CMCC was consistent with the flotation efficiency, and the LPI values of the other two similar samples were overall positively correlated with their flotation performance, suggesting that the method is universal.

Feb 14, 2023

By M. P. Neira

In-situ leaching of copper from chalcocite relies on ferric iron concentration in the lixiviant being reduced to ferrous. To re-establish the ferric concentration in solution, ferrous must be re-oxidized. This reaction is slow under normal chemical conditions but it is catalyzed by Thiobacillus ferrooxidans bacteria. BHP Copper's Miami In-situ unit developed a bio-reactor as a method of oxidizing ferrous to ferric. The effects on oxidation of temperature, CO2? oxygen, and air injection flowrate were defined. This paper summarizes the results of ferrous bio-oxidation using plastic column packing and oxide ores as bio-reactors and the leaching results of the bio-reacted lixiviant on chalcocite ores.

Jan 1, 1997

L.R. Bower In regard to the paper by J.B. Gwiazda, it makes a highly technical approach to show that the µ factor used by designers of lemniscate-guided roof supports has never really been confirmed as a maximum and assumes that convergence is vertical. Also, the paper does not appear to take into account deflection of structures, which occurs when the lemniscate and base members are fully loaded to their maximum stress level, nor the front to back line of the support in relation to differential roof to floor movements caused by strata movements under pressure. It is not unusual for differential movements to be slightly diagonal to the line of the support, particularly in faulted areas and on gradient faces. The paper also does not take into account consolidation of fines immediately above and below the support. Generally speaking, any differential movement is from face to waste and under these conditions the µ of 0.3, which appears to be an international standard, has worked in practice. However, if the face end of the support is lower than the waste end, then the µ of 0.3 can be considerably increased, giving rise to the damage mentioned in the paper. The ideal design should aim for a slightly forward bias in the lemniscate guide so that the last increment of setting is toward the face, tending to close any fissures that may have developed during the support advance cycle. The support should also be fitted with positive set valves to ensure that a high setting load density is attained to minimize bed separation. As far as powered supports are concerned, convergence is irresistible and all powered supports converge at their rated yield load. A similar principle can be applied to the differential roof to floor movements to drastically reduce the very high forces that would otherwise be applied to the lemniscate structures and pins and that, in turn, are transferred to the base arrangement and floor loading. Any differential movements are usually catered for by the 0.3 µ factor or deflection of structures in the lemniscate guide arrangement and consolidation of the floor. The floor loading, due to differential movement, is in addition to the support convergence load and requires additional bearing area to avoid possible floor penetration. Some seven years ago, Fletcher Sutcliffe Wild Ltd. (FSW) introduced a lemniscate-guided shield support where the lemniscate linkage is connected to the roof bar through two horizontally converging rams to allow differential movement to take place above a given rated figure. This is a known force and can be guarded against, whereas with rigid connections the forces, as yet, are unconfirmed. By careful design, a horizontal force in excess of 6 MN (60 tons) opposes differential movements for a total ram loading of only 2.5 MN (25 tons), or 1.25 MN (12% tons) each. This principle can considerably reduce the length and weight of the support in comparison with a rigid pin-type structure ; also, the yield load rating can be increased without affecting the lemniscate forces. The graph shows the tensile and compressive forces in a lemniscate linkage of a support with and without hydrostore. These forces react into both the roof beam and base members and, as can be seen from the support height to linkage load graph, a considerable reduction in these reactions is gained by the use of the FSW patented hydrostore system. Floor loading is considerably reduced under maximum µ conditions, and by allowing the roof bar to move with the strata, some degree of improvement to strata control is achieved in line with the assumptions in the paper. In practice, these movements have only been in the region of a few millimeters, which, in turn, reflects on the improvements to strata control by the addition of positive set valves. Supports to this design of both 450- and 280-t (496-and 309-st) rating have been successfully used in the United Kingdom for several years, negotiating many faulted areas without one single reported need for repair or maintenance. This includes supports left unattended during the year-long strike, proving the reliability of the system.

Jan 8, 1986

By Will B. Jamison

The most serious safety problems encountered in U. S. underground coal mines today are related to the roof bolting operation. Also, roof bolting is usually the operation which limits coal production of the section. The purpose of my paper is to review some of the research, developments, and new ideas related to roof bolting. Many of these ideas have originated at. coal mines or with manufacturers. Most of the research on fundamental improvements has been funded by, and is a part of, the excellent and broad plans of the Bureau of Mines.

Jan 1, 1977

By M. S. Moats, W. C. Hartzell

The stable domestic supply of gallium, indium, and germanium has been identified as a critical need for the United States. Electric arc furnace dusts, processed to recover zinc, produce a residue that could be a potential source of these critical materials. An industrial zinc leach residue was characterized to determine its particle size, chemical composition, and predominant mineral phases. Heated, atmospheric, agitated leaching using sulfuric acid and hydrochloric acid was examined to determine the extractions of gallium, indium, and germanium as a function of concentration and temperature. Extractions of gallium were found to be similar to iron in all experiments. The maximum percentage of Ga, Ge, and In leached into solution were 71%, 63%, and 48%, respectively.

Feb 1, 2023

By Steven K. Ruggieri

Increased coal production on longwalls has brought with it higher levels of dust generation. Most U.S. longwall mining operators have difficulty complying with Federal dust standards, which are stricter than European standards. Longwall operators faced with a longwall that is "out of compliance" have implemented a variety of practices designed to reduce dust levels. Mining conditions and other important variables, however, can cause fluctuations in dust levels that may overshadow the performance of a new dust control technique. This can result in the continued use of an ineffective technique or lead to the abandonment of an effective dust control technique. No single technique can keep a longwall in compliance. Maintaining compliance requires a fundamental approach to dust control -- proper application and continued use of effective dust control techniques.

Jan 1, 1983

By R. E. Miller

Hoisting coal using water and air is a technology which has potential to improve the economics and safety of transporting coal. The Coal Air-Lift Hydrohoist is a prototype coal hoisting system developed by the U.S. Bureau of Mines (USBM). This paper discusses the method used to regulate the supply of water to the 50-m-high hydrohoist U-tube such that the pressure difference at the bottom of the U-tube is held constant. Maintaining a constant pressure difference results in a steady flow of slurry out of the hydrohoist.

Jan 1, 1995

By O. K. Brown

U.S. Borax has two tailings disposal requirements which are uniquely different in many respects, but with the common goal to minimize the impact on the environment, utilize dependable technology and minimize the economic impact. The existing borax mine in the grid Mojave desert of Southern California has gone through a series of changes in tailings disposal practices in the 56 years of operations, The other tailings disposal requirement is a new molybdenum mine, presently in the feasibility phase, in the high precipitation setting of Southeast Alaska. II. Introduction U.S. Borax is faced with two tailings disposals situations, at diverse locations:

Jan 1, 1984

By Gene Mattila, Ron Boyd

Introduction Rock bolting is a general term that encompasses pinning, roof bolting, rib bolting, and cable bolting. Rock bolting contributes the highest nonproductive cost and is the most significant safety risk in mining today. Total installed bolt costs are now more than $20 per bolt. Rebolting or repair work doubles this. And bolting accidents account for about 30% of all fatal and nonfatal lost time accidents. It is only logical, then, for the mine operator to install the highest quality anchors possible. Every bolt on the market - tensioned, untensioned, full contact, or point anchor - has designed capabilities in axial, shear, and fluctuating ground conditions. Bolts will provide a designed support if material specifications and installation procedures fall within the manufacturer's recommendations. This also assumes that there are no unexpected geological or operational changes. Proper material specifications and installation procedures should guarantee the mine operator a quality anchor. To help assure this, the Mine Safety and Health Administration (MSHA), the US Bureau of Mines (USBM), and the AMC Manufacturers group developed stringent ASTM materials standards. These govern mechanical point anchor bolts and bolts using threaded and nonthreaded rebar. There are also minimum standards that suppliers must comply with in the manufacture of frictional bolts. However, most frictional bolt standards are based on the manufacturer's own specifications. It would be impossible to set uniform regulations on frictional bolts. Each bolt provides support in a slightly different manner and thereby requires different material needs. Quality Control In any case, material quality can generally be assured through tight order specifications and periodic quality control checks. The problem with installing quality anchors does not solely lie with the material. It includes all the events that occur from the time a bolt leaves a manufacturer to the time it is installed. The anchoring ability of any major type bolt can be affected by transportation, storage, mechanical performance of installation equipment, installation demands of the operator, proper drilling accessories, and local geology. Table 1 and Fig. 1 document the negative events that can affect each bolt and the degree to which it can be affected. Drilling a hole of oversized diameter, for example, is an operator controlled factor. It will adversely affect most bolts. An over-sized diameter reduces, or even eliminates, the anchorage capability of a mechanical shell. It will reduce the support capacity of a split set to nearly nothing. And it will cause a partial or incomplete grouting around the resin bolt. Frequently, due to bit wear, holes are drilled undersized in diameter and may not be properly cleaned out. In this case, it will be difficult for the operator to push the mechanical shell into the hole, thereby causing him to drill another hole. In cases where the bolt is obviously not providing anchorage, operators will probably drill another hole and place another bolt. Rock Bolt Regulations It is the situations where a bolt is improperly installed in the hole, but gives the appearance of a good bolt, that are frightening. In fact, some safety officials and engineers believe that only 50% to 60% of installed bolts are working. These bolts cause irregular ground load transfers in other bolts and overload them. This causes hazardous situations and overstressing. It is these bolts that fail prematurely 200 to 255 mm (8 to 10 in.) behind the face and possibly contribute to the high accident rate. The government and several manufacturers recognized the need to check the integrity of rock bolts. These programs are in different stages today. Tight torque regulations have been established for mechanical

Jan 4, 1985

Grinding and energy input in stirred media mills are studied as functions of grinding time, stirring speed, media size and density, solid concentration, impeller and tank dimensions and design, and other relevant variables. Ground product size and surface area are determined with respect to the above variables. Changes in energy input and media/pulp rheological properties during grinding are described. The best conditions for grinding limestone in the laboratory stirred media mills have been identified. Equations for correlations involving power and modified Reynolds numbers have been established.

Jan 1, 1995

"The Mine Haul Road Optimization Alliance is an Australian industry-academia collaboration which has been developed to support mine haul road operators by fully integrating mine road design research solutions with industry end-user service providers to design, assess, implement and monitor the various equipment, materials and road management strategies required to optimize the safety, environmental and economic performance of a haul road. Initially, a broad overview of the university-industry collaborative landscape is presented, following which the current situation in the Australian mining sector is reviewed both nationally, and on a country-wide basis, internationally. This insight places realization of a collaboration between Curtin University Western Australian School of Mines Mining Engineering and Metallurgical Engineering (WASM ME2) and the Haul Road Optimization Alliance (HROA) industry members into context of opportunity. Following an overview of the HROA collaborative structure, aims and objectives, it is shown how academia and industry can collaborate to deliver a more robust solution to mine haul road design, performance or management needs, especially where integrated solutions are needed. Critically in this approach, implementation and monitoring data provided by industry and service-providers alike forms the foundation on which to develop research knowledge and innovation that is more responsive to the end-user requirements, typically represented by ‘early goals’ and implementable solutions. The paper concludes with examples of how the alliance collaborations work in practice to deliver improved mine haul road designs and optimized operational performance, together with the mechanisms used to ensure industry needs are met through focused, end-user driven research and integrated solutions implementation."

Jan 1, 2016

By Amy McBrayer, Vladislav Kecojevic, Juan David Valencia Quiceno, Dragan Bogunovic

The mining industry’s commitment to innovation reflects a history of adopting technological advancements to enhance workplace safety, environmental sustainability and vocational training. The objective of this research was to develop an augmented- reality (AR) system for heavy-equipment operators (HEOs) in surface mining. The developed system has the potential to enhance mine safety, training and data-driven decision- making, which presents a significant step toward a more sustainable, effective and technologically driven mining training, contributing to the industry’s evolution and growth. The AR training system leverages Microsoft’s Power Platform and HoloLens 2 capacities to provide operators with detailed and immersive training guides for three mining equipment, including bulldozers, motor graders and haul trucks. AR guides combine speech controls, 3D objects, informative images and explicative videos in the real working conditions to enhance the operator’s learning process. The system has the potential to modify the training structure based on user performance and provides an efficient approach to data collection during training. This project was developed and applied through a case study in a surface mine in the Southern United States.

Feb 1, 2025

By Harold F. Yde

Hydraulic tailings fill in the Butte deep level mines was based upon studies made in 1958 by the Anaconda Company Mining Research Department, which published Bulletin No. 35, entitled "Hydraulic Stope Filling". Since then, many things have changed. At the time of the Research Departments study, dry mine tailings were hauled by rail cars from the Anaconda tailings ponds, twenty-five miles distant, to the underground mines' tailings fill plants at the Leonard Anselmo, and Mt. Con Mines. Now, with the installation of the new Weed Concentrator in Butte, tailings is delivered by pipeline to a cyclone at the Kelley Shaft, and stope filling has become more highly automated and streamlined. Presently, mill tailings at approximately thirty percent solids by weight, is pumped from the concentrator, eight thousand feet horizontally and upward, to the Kelley Fill Plant, where they are dewatered and deslimed by three Krebs Model D20B Cyclones, which discharge the material into the cased and grouted mine delivery bore holes at desired densities up to seventy percent solids. The vertical boreholes and four-inch rubber lined Victaulic pipe carry the material downward to horizontal distribution lines, which in turn tap into the stops-filling, three inch, unlined steel Victaulic pipelines. The slurry may travel several thousand feet before it finally discharges into the stope, where it lends support to the mined-out area.

Jan 1, 1969

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

"Colorado School of MinesResearchers at Colorado School of Mines (CSM) have developed computational fluid dynamic (CFD) models to study gas distributions and explosion and fire hazards in longwall gobs. In underground coal mines, methane continuously emitted from surrounding strata mixes with air from active mine workings and may form explosive gas zones (EGZs). Some western United States coal mines are also prone to spontaneous combustion (spon com). Insight into oxygen concentrations within the gob is crucial for assessing spon com hazards and mitigation strategies. Nitrogen injection used in conjunction with progressive gob sealing can reduce EGZs and spon com hazards by forming a dynamic seal that separates the methane in the gob from the air that ingresses from the face. This paper describes CFD modeling simulations studying the formation of such dynamic seals by optimizing the nitrogen injection locations. The impact of nitrogen on oxygen ingress and formation of EGZs is discussed. Optimum nitrogen injection quantities and injection locations were determined. Dynamic seal formation is most effective if the headgate nitrogen injection locations are split between the first crosscut inby the face and a second location about 300 m (1,000 ft) further inby. INTRODUCTION Underground longwall coal mine ventilation systems are designed to dilute hazardous gases and to provide breathable air to miners working in the area. Methane gas is liberated as the mining process extracts the coal and disturbs the surrounding strata. Methane mixes with the ventilation air and often produces explosive gas zones (EGZs) within longwall gobs (Brune 2013). Past CFD modeling research of underground coal mine ventilation systems has shown the effects of face air quantity on EGZs (Worrall 2012) and nitrogen injection to control spon com (Balusu et al. 2005; Ren et al. 2012; Ren et al. 2011; Smith and Yuan, 2008; Yuan and Smith, 2014). Other modeling approaches include network ventilation models of oxygen ingress (Dziurzynski and Wasilewski, 2012), and coupled Linear Network CFD algorithms (Wedding 2014). In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), CSM researchers are using Fluent®, a CFD software package by ANSYS, Inc., to model gas compositions and flows in underground longwall gobs. Figure 1 shows a progressively sealed gob with a U-type ventilation system in a three entry development. As the longwall advances, seals are constructed along the headgate in the crosscuts between the center entry and the gob. Additional gob isolation seals are built to block off the headgate entries inby the face. Nitrogen is injected through the seals in the first two crosscuts on the headgate side and at the first crosscut inby the face on the tailgate side, as shown in Figure 1."

Jan 1, 2015

By S. Davis

It has been accepted almost as dogma that sampling contributes most of the error to fluctuations in gold fire assays. Differences in assay results on pulp material from the same sample interval are frequently regarded as evidence of the presence of the so called "nugget effect" or relatively coarse gold particles. It is true that if coarse gold particles are present they contribute to substantial sampling fluctuations, but while the process of sampling is probably the major source, the analytical process cannot -be completely ignored as a possible contributor to erratic assay results. In order to maintain a stable assay process, the analytic part of the system must be kept in control as well as the sampling and preparation part. One way of monitoring the performance of the analytic system is to systematically assay standard material whose sampling characteristics are carefully controlled. Gold assay standards are not prepared nor can they be prepared to account for both sampling and analytical errors. It is not possible to send coarse material to a lab for preparation (which includes both the processes of comminution and splitting) followed by fire assay, to make inferences only about the fire assay process. Because most gold ores are very heterogeneous, sampling errors would in most cases completely mask the contribution of the analytical errors. Assay standard material is prepared only to assess the accuracy and variability in the fire assay process.

Jan 1, 1995

By R. J. Lee

Asbestos analysis is conceptually simple. The objective, in most environmental analyses, is to determine the number of asbestos fibers per unit area or volume in a sample. The sample may be a consumer product, an ambient air sample, or a water sample. This determination is complicated by several factors including sample collection and preparation, counting techniques, and the operational definition of asbestos in use. Three different definitions have been used in the study of environmental samples; these are summarized in Table 1. [ ]

Jan 1, 1979

By R. R. Swanson

Liquid ion exchange is becoming more and more important in hydro-metallurgical processing and recovery of metals. The key to success for this process are reagents which have suitable operating characteristics. One of these important characteristics is a relatively fast phase separation rate in the extraction and stripping circuits, as this greatly affects the size of plant required. A test for measuring phase separation rate is needed to help evaluate liquid ion exchange reagents. Such "a test also would be useful for evaluating carrier solvents that are used for diluting the re-agents. In fact, one standard test method would be very desirable as it would provide a common basis for comparing reagents and sol-vents. The phase separation test described in this paper has been used successfully for several years with the copper reagent, LIX®64N. The test is set up for feed liquors containing low copper concentrations. For other types of systems, modifications in procedure probably would be necessary. However, this test and the associated apparatus could be the basis for a standard phase separation test.

Jan 1, 1972