Search Documents

By J. L. Huiatt

Kerosine, fuel oil No. 2, vapor oil, and fuel oil No. 6 were separated into general hydrocarbon fractions by ion exchange chromatography and adsorption chromatography. The collecting properties of these fractions were evaluated by flotation of molybdenum and copper minerals from a natural chalcopyrite ore. Paraffin fractions and aromatic fractions of low polarity produced the best molybdenum recoveries. Selective flotation of molybdenite from copper sulfide minerals was not possible with any of the chromatographic fractions.

Jan 1, 1972

By D. Küster, G. Franken, P. Schütte, J. Vasters

The CTC (Certified Trading Chains) mineral certification system has been piloted in Rwanda since late 2008. CTC project implementation is jointly driven by the Federal Institute for Geosciences and Natural Resources (BGR) and the Rwanda Geology and Mines Authority (OGMR), in cooperation with other national stakeholders. Five Rwandan mineral producers participate in the CTC project with their flagship mining concessions. Based on independent third-party audits, CTC certifies supply chain due diligence measures of these companies engaged in the artisanal mining sector through on-the-ground assessments of mining conditions, transparency, as well as mineral origin and traceability. The CTC system thus allows responsible mineral producers and their clients to verifiably demonstrate supply chain due diligence and good governance in conflict-affected and high-risk areas.

Jan 1, 2011

By Jeffrey R. Kelly, Paul M. Kubera, Richard A. Howk

Mixing of solid-liquid slurries is a unit operation that is widely encountered in the minerals processing industry. Applications may range from simple slurry storage in open tanks to complex chemical reaction systems under extreme conditions of temperature and pressure. The specific process requirements dictate both the degree of mixing required and the type of agitation employed to achieve the desired results.' Many continuous-flow process applications feature tanks operating in series to provide a discrete number of stages and a known residence time for the slurry. Because these tanks operate at a constant level in an overflow mode, the mixer must maintain uniform solids concentration and size distribution throughout the tank; failure to achieve uniformity results in accumulation of coarse solids in the tank, ultimately leading to a process or mechanical failure. Downward-pumping, axial-flow mixing impellers are widely employed to produce uniform solids suspension. The specific impeller type, number, size, and power draw is a function of each given situation. The use of high-efficiency, fluid-foil impellers (Figure I) has evolved as a recognized standard for these flow­controlled applications. Recent small-scale experimentation and full-scale experience has demonstrated that, when uniformity is required, capital and operating expense can be minimized by employing an additional upper impeller pumping in the upward direction.

Jan 1, 1995

By Mahaboob Basha Shaik, Shakuntala Tudu, Indrajit Paul, Chandra Sekhar, Neha Gupta, Amit Kumar, Srinivas Dwarapudi, Arvind Kumar Patel

In this study, the effect of colemanite and calcined colemanite (CC) addition on the properties of iron ore pellets is studied. The pellets are prepared in a lab without and with 0.2% colemanite and varying amounts of CC from 0 to 1.0 wt%in steps of 0.2%. A reference pellet is prepared under typical plant conditions, and the properties of the reference pellet are considered as the base value for improving the cold compressive strength (CCS) while maintaining the other parameters at an acceptable limit without altering the pellet. The study also aims to provide a detailed characterization of colemanite and calcined colemanite to better understand their behaviour during firing. The lab-scale results show that the CCS of pellets made with 0.2% colemanite was reduced by 222 points (60%) as compared to the reference pellets due to crack formation during firing. The results show an improvement in the CCS of the indurated pellets with CC dosage up to 0.4%, and decreasing strength is noted thereafter. It is observed that the swelling index increases with the increase in calcined colemanite dosage. To simulate plant conditions, reference pellets and pellets with optimized CC dosage were fired in a plant furnace.

Oct 16, 2020

By Heinz Petry

In deep strip mines the job of moving overburden may be so much bigger, and more costly than the removal of coal or ore that the operation is often called dirt mining. Constant improvement in stripping machines and techniques of using them is needed to offset rising costs and to increase production in mines that are now operating, and to make it economically possible to work deeper or thinner deposits.

Jan 1, 1962

By Miguel Carrera, Jose Arnal, Julian Ortiz, Maarten Haest, Fouad Faraj

ShovelSense is a complete solution for bulk ore sorting at the mine face that combines robust shovel bucket mounted X-ray fluorescence sensors, with real-time material classification, fleet management integration and supporting cloud-based data infrastructure, to ensure each truck always goes to the right destination. Correct truck destinations are a challenge in many current mining settings because the material classification of a truck, which is the key input into the truck destination, is often based on estimates at block resolution (~20x20x15m), with limited adjustment for blast movement and mixing. In this contribution, we present a geostatistical, data driven approach to estimate the potential value of bulk ore sorting at the mine-face for seven open pit mines. The approach is premised on the assumption that truck loads within blocks follow a simple gamma distribution. Standard ore control data from the seven mines have been used to estimate the potential bulk sorting value at these operations and ShovelSense-integrated dispatch datasets have been used to validate these estimates for specific benches on which ShovelSense operated. ShovelSense results validate the ore control data-based value predictions and show how at mine-face bulk ore sorting value varies between distinct deposit types. In general, deposit types that have higher bulk ore grade contrasts, display more potential ShovelSense value. The manuscript concludes with the limitations and opportunities of applying the proposed value estimation approach to evaluate at mine-face bulk ore sorting opportunities for open pit operations.

Jun 25, 2023

By G. V. R. Landman

In order to obtain a better understanding of the explosion risk at the coal face, anomalies in the ignition sensitivity for different modes of ignition of hybrid mixtures of dust, methane and air were studied. Results indicated that the explosible behaviour of the working environment is highly dependent upon the ignition source and the fuel composition. For example, depending on the ignition source, the same hybrid mixture can be inert or extremely explosible. In conclusion, it is stressed how the explosion risk can be expressed in terms of a safety factor which takes into account the influence of both the fuel and the ignition source.

Jan 1, 1994

By A. K. Fallaw, D. L. Taylor, G. Wang, L. R. Moore, S. Dobson, C. B. Parkinson

"Over the years, the decline of high grade ores have become an increasing problem in the global mining industry. As such, techniques and chemistries must change in order to continue to meet the market demand and quality. Reverse cationic flotation of quartz and silicates is one of the most important techniques for generating the industry standard product from minerals such as iron and phosphate ores. Amine collectors are the global standard in such processes. However, as the ore quality continues to decline so must the chemistry change to meet the change in ore composition. This paper will focus on the introduction and full scale application of a novel amine collector towards a cleaner flotation process in phosphate beneficiation with Crago process. The results suggests the collector is capable of improving the phosphate recovery, in this cleaner circuit, to approximately 94% with minimal sensitivity to the everyday changes in feed grade.INTRODUCTION The days of mining high grade minerals are long gone, but the demand continues to increase. Phosphate ore, for example, is most dominantly demanded from the agriculture industry as a fertilizer component (i.e. diammonium phosphate, DAP) (FAO, 2014). Some literature suggests that global food production must increase by approximately 70% by 2050 (Cordell, 2009). It is also suggested that the peak global phosphorus production will occur around the year 2033, which is the period at which the easily accessible reserves have been depleted. Currently, phosphorus is commonly mined with a BPL (Bone Phosphate of Lime) concentration of 12-20% and a remainder typically being gangue minerals such as silica, clays, metal oxides, calcareous minerals, and carbonaceous minerals. These gangue components can lead to various negative processing and utilization consequences. Calcium, from carbonaceous minerals, is problematic due to the elevated levels of sulfuric acid required to convert the phosphate rock to the acid form (SRI Consulting, 2009). Calcium can also lead to elevated dosages of flotation reagents due to the desire of the fatty acid to coordinate to calcium minerals. Carbonate leads to increased levels of foam during the wet acid process. Silica is associated with the level of insols (acid insolubles), which must be less than 10% in the final concentrate that will be transferred to the chemical plant for acidification. Phosphate ore can generally be classified as carbonaceous or siliceous (El-Shall, 2003). Siliceous ores are commonly processed through various sizing steps followed by multi-staged flotation (Figure 1) (FIPR, 2014 & Güven, 2010). Though the higher grade phosphate pebble is declining, many mines are still able to size good enough to produce some amount of such pebble. Unlike most metal flotation processes where grinding is a necessity for an optimal process, Florida phosphate flotation does not generally require aggressive grinding and can typically operate at 0.1-1.0 mm. The rougher flotation step applies pH modification to achieve the optimal pH of 8.8-9.3 followed by conditioning with a fatty acid type collector, which builds a hydrophobic waxy layer on the surface of the particle to assist in the flotation. This generally achieves higher than 85% recovery of a product with 50-60% BPL and 15-30% insols. Unfortunately, DAP production generally requires 3.5 tons of phosphate rock containing greater than 63% BPL to produce 1 ton of phosphoric acid (ArgusMedia, 2014). Thus, further purification is required to achieve the grade by the chemical plant for fertilizer production. After the fatty acid is scrubbed off the phosphate particles using sulfuric acid (pH 2.5-3.5), the pH is generally operationally readjusted to 6.5-7.2 by washing with “fresh” water. A second collector is applied prior to the cleaner, which is a reverse cationic flotation process. This collector is typically a cationic amine based reagent, which should have an affinity for silica containing mineral"

Jan 1, 2015

By F. Shigeyoshi

The development of pelletizing during the last ten years has continued, however, self-fluxing pellets have not been regularly and commercially produced for use in blast furnaces, except as Kobe Steel, Ltd., Japan. This paper tells about unique developments for self-fluxing pellets, and their effects when used in Kobe Steel's No. 3 blast furnace at the Nadahama Works (inner volume 1845 Nm3, hearth diameter 9.5 m)., Several phases of the pelletizing process are discussed individually, and also their relation to performance in blast furnace operation. Special emphasis is placed on proper preparation of the limestone added to the raw materials, and indurating at optimum conditions. Means of improving pellet quality by correct control of size distribution of the raw materials used in pelletizing, and indurating temperatures, are also discussed. As basicity (CaO/SiO2) of pellets increased 0. 1, coke consumption decreased 3. 8 to 4. 2 kg per ton of hot metal, when using 70% pellets in the iron burden.

Jan 1, 1969

By Henry R. Colen

When we were asked to prepare a paper on gold to be part of the Economics of Precious Metals session, our immediate thought was that we should address the question of supply. Are the existing mines of the world capable of filling the demand for gold? We recognized that gold does not conform to the normal pressures of supply and demand. Major new sources of production and increased sales might have a very short term effect and depress the price but this does not last very long. Those forces that affect gold prices are very different from the ones economists normally deal with. Factors such as mass psychology, political tensions and fear are certainly more important to the gold price than supply and demand in today's world.

Jan 1, 1981

By John W. Leonard

The typical tunnel boring machine in use on today's tunnel project uses 15'2-inch diameter cutters at a nominal load of 45 kips per cutter. The cutterhead rotates at a speed of 120 over D revolutions per minute where D is the cutterhead diameter in feet. The typical machine operates about 50 percent of the time. Delivery of a new machine takes 12 to 15 months. The TBM is a specialized tool and not applicable to all jobs. There is a range of job conditions that limit the economic use of a TBM. The machine should provide a thrust per cutter at least twice the compressive strength of rock in psi and up to three times the rock strength is required if in "granitic rocks." The rock strength in psi must be at least three times the cover above the tunnel in feet or the machine may stick. For example, 2,500 feet of cover requires at least 7,500 psi rock to avoid problems. When the RQD's over a significant distance of the project are less than 50, the TBM becomes support-bound. When a large percentage of the time is spent waiting while the ground is supported, the TBM cannot perform well (See Figure 1). This problem increased inversely with tunnel diameter. We are finding that increasing the RPM's does not significantly increase progress. The increased RPM results in a substantial decrease in cutter penetration. The explanation for this decrease appears to be vibration, cutterhead drag, or lack of stiffness in the cutterhead (See Figure 2).

Jan 1, 1981

By A. B. Cortes

This research work discusses the development of a two-dimensional model that represents the flow that occurs in the inlet section of hydrocyclones. The governing equations are the two-dimensional, unsteady, incompressible Navier-Stokes equations in cylindrical polar coordinates with primitive variable formulations. In this approach, no assumptions have been made other than independence in the axial direction. The full two-dimensional Navier-Stokes equation in the r-a plane is used. The commonly used simplifying assumption of axisymmetry is not used. A numerical technique based on a newly developed spectral-difference method is used to solve the equations. The spectral-difference method is a multi-domain, and multi-dimensional extension of the Jacobi polynomial collocation technique. The computational grid for the inlet section is composed of 25 sub-domains which result from five partitions in the angular direction and five partitions in the radial direction. Several test cases are used to validate the appropriateness of the numerical model.

Jan 1, 1995

he leaching behavior of palladium in ammoniacal solutions has been investigated by using the rotating disk technique in an autoclave. The study included the effect of rotating speed, temperature, oxygen pressure, composition of ammoniacal solutions, and catalyst on the overall leaching rate. The dissolution of palladium in ammoniacal solutions was discussed in view of the thermodynamics and a kinetic model. Even though the potential-pH diagram suggests that palladium metal can dissolve in ammoniacal solutions at room temperature, it was found that the dissolution was too slow at temperatures below 100°C but was significantly improved at higher temperatures. It was also found that the rotating speed of palladium disk had no effect on the leaching rate. The apparent activation energy was found to be 69.7 kJ/mole. Based on the results obtained, it is concluded that the dissolution of palladium is controlled by chemical reaction.

Jan 1, 1997

By Mustafa Akser

The Pipestone Lake anorthosite complex in Manitoba, Canada, was recently been re-identified as a potential source for titanium, iron, and vanadium. The present study utilized a 350 kg hard rock sample, which originated from the "Main Central" zone of the deposit. Commercial pilot-size equipment, such as dry low intensity roll magnets, wet high intensity magnets (WHIMS), and high tension electro-dynamic roll separators, was employed. As products, ilmenite up to 48.5% TiO2, and magnetite concentrates up to 87.9% Fe3O4 with 5.25% TiO2 were obtained. The majority of the vanadium reported to the magnetite concentrate. Subsequent characterization of various separation products shed light on the potential grade and recovery of the minerals from this deposit.

Jan 1, 1996

By M. Canty

Results are presented that were gathered during pilot-and field-scale testing of an innovative technology, sulfate-reducing bacteria (SRB), designed to treat and control acid mine drainage (AMD). The project was performed under the Mine Waste Technology Program (MWTP), which is funded by the U.S. Environmental Protection Agency (EPA) and jointly administered by the EPA and the U.S. Department of Energy through an Interagency Agreement. The MWTP is implemented by MSE, Technology Applications, Inc., located in Butte, Montana. Sulfate-reducing bacteria, a common group of anaerobic bacteria, produce hydrogen sulfide and bicarbonate when supplied with sources of carbon and sulfate. Hydrogen sulfide reacts with metal ions in AMD, precipitating them as metal sulfides; the bicarbonate serves to help neutralized the drainage. Pilot-scale testing was performed within eight packed-bed reactors at a temperature representative of a field application of this technology in a northern climate, nominally 8°C. The reactors, packed with an organic substrate, were operated continuously in upflow configurations receiving AMD at a flow rate corresponding to a 5-day retention time over a test duration of 60 days. During this time, numerous physical and chemical parameters were monitored. Pilot-scale metal removal efficiencies reached 99% for zinc, 99% for aluminum, 96% for manganese, 98% for cadmium, and 96% for copper. Iron and arsenic removal was not as effective as the aforementioned metals, which was largely attributed to the high levels of iron and arsenic contaminating the organic substrate. Evidence existed that both adsorption and sulfate reduction were occurring within the reactors.

Jan 1, 1998

By E. A. Devuyst

Metallurgical processes involving the use of cyanide such as gold cyanidation, metal plating and flotation, generate effluents containing cyanide and cyanide in complex combinations with heavy metals in quantities exceeding those regarded as being safe for discharge into streams. A new process for destruction of free and complexed cyanide and related-species in wastewaters has been developed at the Inco research laboratories using sulfur dioxide, air and lime. High reaction rates are obtained in the presence of a small amount of copper which acts as a catalyst. Cyanide species can be reduced to as low as 0.1 mg/L in a very short treatment time. Examples of treatment of gold mill effluents and barren slurries, plating rinse waters and flotation liquors or tailing slurries are given.

Jan 1, 1982

By A. S. Ibrado

The adsorption of silver on activated carbon from cyanide solutions was studied as a function of concentration, ionic strength and pH. In cyanide solutions, silver exists mainly as the linear Ag(CN)2 complex and adsorbs on activated carbon following the Freundlich isotherm. The uptake and rate of adsorption increase with the addition of KC1 and KNO3 but changes only slightly with pH. In contrast, the adsorption of Cu(I), Zn(II), Cd(II), and Hg(II) shows marked changes with pH, closely following the predominance profiles of their neutral and singly-charged cyano complexes. Clearly, multicharged negative complexes are repelled by the negatively-charged carbon surface. This sensitivity of activated carbon to the charge of the adsorbing species indicates that silver adsorbs as an anion, not chemically bound to the co-adsorbing counterions. For the same reason, activated carbon is selective to metals that form neutral and Singly-charged cyano complexes, namely gold and silver.

Jan 1, 1988

By J. A. M. Cano

Introduction Since the beginning of operations at the pellet plant at Ponta Ubu ES, Samarco Mineração SA has produced pellets for direct reduction and blast furnace processes. Of the total amount of pellets produced from 1977 through 1993, 55 % are used in the blast furnace, about 45 Mt (49.6 million st). The principal components of pellet gangue are calcium oxide, magnesium oxide, silica and alumina. They should be added in adequate quantities to guarantee the mechanical resistance of the fired pellets under blast furnace conditions. Over the years, the pellets produced by Samarco had a silica content between 2.5% and 2.8% and varying binary basicity preferably between 0.8 and 0.85. On the other hand, the increasing amount of industrial waste in siderurgical plants caused by the increase of steel production has caused some countries to put into practice methods to reduce the volume of slag produced in the blast furnace. This paper's goal is to find an alternative for decreasing the amount of slag produced in the blast furnace. It is possible to decrease pellet gangue by decreasing the silica content to about 2%, leaving the metallurgical properties and quality of pellets unaltered. For this work, Samarco pellets were used with Si02 between 2.5% and 2.8%, pellets with high silica and pellets with Si02 between 2.0% and 2.3% low silica. Both were partially fluxed by the range of varying basicity CaO/SiO2 from 0.8 to 0.95 during production. Experimental tests on pilot scale Thhis work began in January 1986 in the pilot plant (pot grate, Fig. 1) at Samarco. Its goal was to obtain preliminary data that would indicate the bybility of the project. It also formed a solid base to extend the studies in tests on an industrial scale of production for blast-furnace pellets. The pot grate is a test furnace composed of a gas burner, a combustion chamber and a grate, connected by hot air ducts. The burner is fed by a mixture of LPG and air. It reaches high temperatures through oxygen injection. The combustion chamber heats the air that comes from the turbocompressor. This hot air flows through the ducts to the grate on which the pellet samples are fired. During updraft drying, downdraft drying, preheating, firing and afterfiring, the upward and downward direction of the air flow can be controlled by valves driven by pneumatic cylinders. The pot grate indurator was fully automated in August 1989. Positive and negative pressures measurements resulting from gas passing through the pellet layer, as well as temperature readings, are recorded in graphs in relation to time for all tests. The tests depend on the various steps carried out in sequence that can influence the results of the tests. Therefore, some criteria were adopted to restrict the number of variables in the process. This was done to facilitate the results of the analysis. The pellets were composed of concentrate, bentonite, hydrated calcitic lime and metallurgical coal, all regularly used in the pellet plant. The material balance of the pellets mix was determined from the chemical analysis of the components. Table 1 shows the chemical characteristics of the concentrate and the additives used in the pilot plant and industrial tests. The basicity has a marked influence on the metallurgical properties of the pellets produced by Samarco with a silica content between 2.5% and 2.8%. However, for pellets with low silica (about 2%), it was necessary to study the variation in the parameters of quality in a wide range of basicities to deliniate with precision a scope of work. A large variety of low-silica blast-furnace pellets were produced at the pilot plant with binary basicity varying between 0.8 and 0.95. After chemical analysis, those pellets were separated into five groups of different binary basicity (0.8, 0.84, 0.87, 0.90 and 0.95). Each was then split, one part for metallurgical tests in the laboratory at Samarco and another to be evaluated in a laboratory for metallurgical tests in Germany. It was agreed that the tests to evaluate the quality of the pellets in the two [ ]

Jan 1, 1996

By K. Luxbacher, D. T. Hristopulos, S. Schafrik, J. Diaz, Z. Agioutantis

Big data is generated from both surface and underground mining operations. Such data contain a wealth of information concerning safety and health in the workplace and production parameters. This paper will discuss the progress towards developing an accurate forecasting model for methane gas concentration based on the analysis of data collected from Atmospheric Monitoring Systems in underground coal mines employing time series models. Several procedures need to be applied to raw data, such as data cleaning and filtering for outlier removal, data homogenization and segmentation, and exploratory statistical analysis. The data analyzed were retrieved from two coal operations in the Eastern US. A negative correlation between barometric pressure and methane gas concentration was established, at least for certain data segments. Such correlations raise the possibility that barometric pressure data can predict variations of gas concentration in the mine. The datasets will be further investigated to establish the robustness of barometric pressure and gas concentration correlation and explore the dependence of gas concentration on other factors related to mine design and operations

Mar 2, 2022

By J. S. Hu

FTIR spectroscopy has been used for the characterization of adsorbed oleate at the fluorite surface. It has been found that modest changes in the adsorption density at high temperature and high oxygen potential do not provide a satisfactory explanation for the significant increase in the hydrophobic character of the system under similar conditions. Rather, FTIR spectroscopic measurements suggest that chemical interaction between adsorbed oleyl groups occurs at high temperature and/or oxygen potential and accounts for the increased hydrophobicity. Specifically, the intensity of the =CH bond of the adsorbed oleate diminishes at high temperature and/or high oxygen potential. Such a phenomenon was not observed in control tests with the calcium oleate soap. For extensive reaction at the fluorite surface, the presence of a new surface species has been identified. These results indicate that the fluorite surface catalyzes an oxidation and/or polymerization reaction between adsorbed oleyl groups which results in a more hydrophobic structure at the fluorite surface.

Jan 1, 1986