Search Documents

By A. R. Laplante

In this paper, the performance of the Knelson Concentrator and of the batch and continuous Falcon Concentrators are compared. The units are based on different operating principles, and perform quite differently. The Knelson yields very high free gold recoveries over a wide size range of both the recovered and rejected species. It is less effective in recovering very fine (<15 μm) or very flaky gold, as encountered in flotation feeds, concentrates or tails. It is the preferred unit for gold recovery from grinding circuits. The batch Falcon is effective in the fine range, typically less than 37 μm for gold. Its recovery zone is quickly saturated when there is significant heavies in the feed. It works best as a pre-concentration unit, or when sulphide content is low. The continuous Falcon is a versatile unit which is capable of recovering fine heavies (density down to 5 g/cm 3), especially from coarser gangue.

Jan 1, 1993

By Robert L. Hautala

In 1978, Congress established a series of mineral institutes for a limited time to assist financially in mineral industry education and research. Later, education and research were separated, establishing generic institutes for specialized research that transferred the former research budget from the base mineral institutes program. One of the generic institutes is the Mine Systems Design and Ground Control (MSDGC). It provides for research funding specifically for mining. Other parallel generic institutes were established in pyrometallurgy, comminution, waste management, etc. MSDGC was established at Virginia Polytechnic Institute and State University(VPI). The founding group included the University of Alabama, University of Kentucky, University of Nevada Reno, University of Idaho and University of Alaska reporting through VPI to the US Bureau of Mines (USBM) and Congress. Other universities also participated on an ad hoc basis.

Jan 1, 1996

By Bruno Bussière, Michel Aubertin, Anne-Marie Dagenais, Johanne Cyr

A five steps remediation program was commissioned in 1998 for the acid generating Lorraine mine site, located in the Témiscamingue region, Quebec, Canada. It included, as the main expenditure, a cover with capillary barrier effects (CCBE) used to limit oxygen migration. After construction of the cover, instruments were installed on site to monitor the CCBE performance. Modified oxygen consumption tests were also done to measure the oxygen flux through the cover. Results from water content and suction data, measured from 1999 to 2003, show that the capillary barriers effects are effective and that the water retention layer stays near saturation throughout the years. Oxygen fluxes estimated from monthly water content measures are generally below 10 g/m2/year. Results from modified oxygen consumption tests made on the site give almost similar oxygen fluxes. A two dimension numerical model of the Lorraine mine site was also constructed to verify that mathematical models could predict realistically the in situ conditions on such a large scale site. Numerical results obtained for three years show a good concordance between measured and calculated values. The results obtained form these different evaluation methods for the performance of a CCBE concur and confirm the efficiency of this cover in limiting acid mine generation.

Jan 1, 2005

By J. B. Gwiazda

In designing mine workings and adequate roof supports, it is indispensable to determine properties of the strata surrounding the workings. The proper selection of roof supports is based, before everything else, on a thorough knowledge of the roof rock strength, especially tensile strength. This parameter is a vital factor in the delamination of roof rocks and eventual cave-in. It is also important to know the properties of the floor on which the roof supports are set. While driving galleries, it is essential to know beforehand the strength of rocks that will be encountered in the near future during the work. The devices described will help to obtain this information.

Jan 1, 1987

By W. Chae

The influence of solution ionic strength (IS) and electrolyte valence on the flotation behavior of malachite has been investigated. The microflotation tests were conducted over a range of solution IS (1?300 mM) at a constant speed (340 rpm), pH (9.5), flotation time (10 min), and sodium oleate dosage (5.3×10-7 moles/g). The size of malachite ranged from 45 to 53 µm, and two different types of electrolytes (NaCl and CaCl2) were employed. Electrophoretic mobility was also measured over the same IS range employed in the microflotation study. Overall, strong coupled effect of solution IS and ion valence was observed. Specifically, the flotability of malachite increased with increasing IS in the presence of monovalent cation (Na+) while the flotability increased up to 30 mM and decreased with increasing IS in the presence of divalent cation (Ca2+). Notably, the flotability of malachite was greater with the presence of Na+ compared with Ca2+ under high IS conditions (IS>30 mM). Consistent trend for Na+ versus Ca2+ was observed from the flotation results with different SO dosages. The characterization and flotation results suggested that the trend was likely attributed to the increased unfavorable interaction between malachite and bubble via the charge reversal of bubbles and malachite at higher IS in the presence of Ca2+.

Feb 27, 2013

By M. E. Hinkle

Concentrations of He, CO2, and O2 in soil gases were measured regularly for more than a year at a site near Golden, Colorado. Samples were collected from a hollow probe at 0.75-m depth and from a plastic hemisphere on the ground surface. Soil temperature, air temperature, percent humidity, And barometric pressure were also measured. Soil moisture was measured only indirectly as amount of rain or snowfall. Higher concentrations of CO2 in both the 0.75-m and surface samples correlated with higher soil and air temperatures, which suggests that CO2 was produced by bacteria. Lower concentrations of helium in both the 0.75-m and surface samples correlated with higher soil and air temperatures. Rain and snowfall appear to affect helium concentrations. Carbon dioxide concentrations were lowest when snow lay on the ground for extended periods of time. No correlation was seen between barometric pressure or percent humidity and concentrations of He, CO2, or O2 at 0.75-m depth or at the ground surface. No correlation, either positive or negative, was seen between concentrations of CO2 and O2.

Jan 1, 1988

By John Newby, Ulf Gwildis, Fred Marquis

From the Brightwater Conveyance System in Seattle to the Second Narrows Water Supply Tunnel in Vancouver, BC, the design and construction of deep-lying tunnels in the Pacific Northwest often require the incorporation of deep portal shafts. Alluvium overlying marine and glacial deposits combined with the high regional seismicity is the common geologic setting. The latest example illustrating the development of shaft design for this scenario is the 40-m-deep shafts of the Annacis Island Wastewater Treatment Plant New Outfall System. The main components of the shafts include the initial lining, providing the excavation support system to be used for launching and receiving a 5-m-diameter TBM; and the final lining, designed to withstand all static and seismic loads and to remain viable for the intended design life. This paper presents design and construction considerations for these shafts against the background of and lessons learned from past project experiences.

Jun 13, 2021

By R. Stefanko

Rock bolting as a method of support continues to increase with applications in many other industries in addition to mining. Nevertheless, with nearly 55,000,000 roof bolts installed in coal mines alone last year, this remains as the single greatest use. While bolts have frequently supported ground where conventional timbering could not, there are relatively few design criteria; and trial-and-error procedures prevail. Furthermore, development of suitable instrumentation that is simple to install and readout, sensitive, durable, reliable, safe and economical in evaluating the effectiveness of a bolt over long periods of time lags behind. Therefore, the pull test continues to be the most popular method of evaluating the applicability of a certain type of roof bolt under specific installation conditions. At Penn State in the Department of Mining, research has been conducted for a number of years to measure bleedoff in carefully controlled laboratory experiments as well as in underground investigations.1,2,3,4 Unfortunately, most of the instrumentation developed has been primarily suitable only for research purposes, not possessing all of the aforementioned characteristics desirable for routine underground use. Other groups also have met with restricted success. Therefore, while relatively crude, the torque wrench continues to remain as the most widely used load measuring device. While both field and laboratory tests continue to be conducted, analytical analyses are attempted to discover the more important design parameters in order that more efficient anchorage might be devised.

Jan 1, 1969

By H. L. Hinds

Economic pressures to increase production to profitable levels reduced the Homestake&apos;s gravity recovery and overall recovery to un-acceptable levels. The operation of the Home-stake gravity gold circuit has increased gravity gold recovery to over 50%, improved overall recovery and increased mill availability for increased tonnage. The gravity circuit consists of three gravity gold recovery stages. The Circuit has four (4) duplex jigs, four (4) belt concentrating strakes and four (4) concentrating tables.

Jan 1, 1989

The most common method used for cleaning the fine fraction in today&apos;s coal preparation plants is froth flotation. Past research and practice has found that froth flotation achieves excellent separation efficiencies for fine coals having only a small fraction of middling particles. However, its efficiency decreases sharply as the concentration of middling particles increases due to the flotation of high-ash particles having a small amount of hydrophobic coal present at the coal surface. Since gravity-based processes are much more efficient at treating middlings, the application of centrifugal washing for fine coal cleaning has been studied with an emphasis on the primary cleaning of fine circuit feed. Results will be shown from a parametric study using a Falcon centrifugal concentrator which reveals that the separation performance is a function of particle size, bowl geometry, feed solids content, and feed rate.

Jan 1, 1994

By Yngve Jordal, Sverker Hartwig

The IVAR Project is Norway&apos;s largest sewer project presently under construction. One part of it is an 8.1 km (26 575 ft) long, 3.5 m (11 ft 6 in.) diam tunnel, bored in one year. The tunneling project has been running smoothly; however, not everything has been easy. A few of its features are highlighted in this paper: The use of 9 0 (12 cu yd) muck cars on a double track back-up in such a comparatively narrow tunnel. Employing only four men in the tunnel, including the loco driver. A quartzite dyke - 96% quartz with 350 MPa (50 000 psi) and more compressive strength - turned out to be 640 m (2 100 ft) thick instead of the predicted 90 m (300 ft). Passing under a gaseous swamp with only same 5 m (16 ft 5 in.) of rock cover on top.

Jan 1, 1991

Ventilation network modeling in mine planning dates back at least three decades, but it is not widely accepted and/or practiced until the last decade, thanks to the advent of modern computers with their increase d speed and storage space. There are at least half a dozen such modeling software packages available on the market each with different features and acceptance. This paper compares five popular software packages,?? VnetPC Pro, MineVent, VentSIM Visual, VentGraph and MFIRE 3.0. A case study using Missouri S&T?s Experimental Mine is conducted to compare the five software packages in features, interface, output display and user-friendliness.

Jan 1, 2012

Geopolymerization is a process by which Al-Si minerals undergo dissolution and polymerization in an alkaline solution to form a monolithic material with a high mechanical strength (Davidovits, 1991; 1994). In this study, Na-feldspar (albite) and K-feldspar (microcline) have been selected to investigate their abilities to undergo geopolymerization. The interaction between alkali metals present in the alkali-feldspars and alkali metal cations contained in alkaline solution during geopolymerization has also been studied. It has been found that both albite and microcline can be applied in geopolymerization to produce geopolymers with a high compressive strength. Although the dissolution of M-feldspar (where M = Na and/or K) in concentrated MOH solution is inhibited when the alkali metal cations of the alkaline solution differ from the alkali metals structured in M-feldspar, the resulting geopolymers are found to demonstrate a higher compressive strength. Moreover, a proper molar ratio of Si/Al in the geopolymeric gel phase and a higher average hardness of the undissolved particles remaining in the geopolymers are found to greatly increase the ultimate compressive strength of the geopolymers.

Jan 1, 2002

By P. Bartel

Coal cleaning can be effected by the bacterium Sulfolobus acidocaldarius, which in oxidizing sulfur and dissolving mineral matter requires carbon dioxide and oxygen; carbon dioxide as a carbon source and oxygen as an electron acceptor. The desulfurization of coal by thermophilic bacteria under elevated partial pressures of carbon dioxide and oxygen was studied at a total pressure of 1 atm. The partial pressure of carbon dioxide was varied over the range 0.00032 to 0.33 atm (0.00032, 0.007, 0.10, 0.33 atm), and the partial pressure of oxygen was varied over the range 0.14 to 0.40 atm (0.14, 0.21, 0.30, 0.40 atm). The maximum rate of coal desulfurization increased by 32%, from 9.0 to 11.9 mg S/1 hr, as air was enriched in carbon dioxide from its atmospheric level of 0.00032 atm to 0.10 atm. Enrichment with carbon dioxide up to 0.10 atm, at constant oxygen partial pressures, increased the desulfurization rate, but enrichment to 0.33 atm caused the rate to decrease. At constant carbon dioxide partial pressures, the desulfurization rate was maximum at oxygen partial pressures of 0.21 and 0.30 atm. At higher (0.40 atm) and lower (0.14 atm) oxygen partial pressures the rate decreaed by 9 to 20%. The desulfurization rate decreased by 58X, from 9.0 to 3.8 mg S/1 hr, when the air pressure was increased from 1 atm to 3 atm. The effects justify an economic analysis during design and operation of a commercial air feed in a process to desulfurize coal by microbial action.

Jan 1, 1986

By J. G. Groppo

A beneficiation process has been developed to provide selective separation of unburned carbon from high loss-of-ignition (LOI)fly ash. Using froth flotation to achieve selective separations requires long residence times and high reagent costs. A proprietary reagent system has been developed to address these limitations. Based on the results obtained from laboratory and pilot-scale investigations, a flowsheet design has been developed to produce two distinct usable products from class F fly ash — low LOI ash and a high-carbon product suit-able for reburning or further upgrading.

Jan 1, 1996

By J. D. Miller, C. L. Lin

In the processing industries, it is well known that particle shape is an important factor which determines the behavior of particulate systems. For example, system properties of technological significance including rheology, suspension stability, agglomeration, packing, permeability…etc, are affected by particle shape. In this regard, characterization and analysis of particle shape is essential for more detailed understanding and improved development of particulate processes. In general, it is clear that the behavior of these systems depends on the statistical characteristics of particle shape. Remarkably few techniques exist to predict the mechanical and hydrodynamic behavior of an irregularly shaped particle or a population of irregularly shaped particles for that matter. The lack of models and correlations can be attributed to the wide variety and complexity of particle shapes, the difficulty of defining shape descriptors suitable for modeling, the limitations of measuring shape, and the lack of classifying techniques to characterize particle shape. In this paper, we present information on how 3D particle shape can be measured, characterized, and analyzed using cone-beam X-ray microtomography (XMT).

Jan 1, 2005

By James J. Brady, Joginder S. Bhore, Robert B. Gordon, Jimmy W. Honeycutt

The authors of this paper have a combined construction experience of 70 years. They have served as engineers and managers on projects throughout the United States and Canada. Approximately 50 shafts have been sunk under their direct and daily participation. Several shafts have been selected from each of their experiences and have been briefly summarized here. SHALLOW SHAFT SINKING Sinking shallow shafts in highly urbanized areas adds an additional set of problems to those encountered in normal sinking operations. During the time between July, 1975 and early 1981, a series of shafts were sunk for The Washington Metropolitan Transit Authority. All of these were located along the "A" line, starting soon after the route departed from its path along Connecticut Avenue, proceeding to Wisconsin Avenue and then along Wisconsin Avenue to the city line at Western Avenue. (See WMATA System Map, Figure 1) The first three shafts were subcontracted from Morrison-Knudsen & Associates, Contract A9a, in July, 1975. They were: Albemarle Street - 27&apos;6" diameter, 78&apos;O" deep Brandywine Street - 30&apos;6" diameter, 88.6&apos; deep Ellicott Street - 33&apos;0" diameter, 110&apos;0" deep

Jan 1, 1985

By M. Hancer, J. D. Miller

It is known from soluble salt flotation practice that the K, Mg double salts of kainite (KClMgSO43H2O), and carnallite (KClMgCl26H2O) are difficult to float and must be converted to other salts such as schoenite (K2SO4MgSO46H2O) and sylvite (KCl) in order to recover potash values. The flotation characteristics of these double salts have now been confirmed in some detail by carefully controlled laboratory experiments with both cationic and anionic collectors. The experimental results are discussed in view of recent experimental findings regarding the flotation characteristics of simple salts, in which the flotation response was shown to be determined by the interfacial water structure and whether the salt could be considered to be a water structure maker or a water structure breaker. The same approach can be use to explain the flotation response of the potassium double salts ; schoenite, kainite, and carnallite. In addition, the sign of the surface charge of schoenite (K2SO4MgSO46H2O), was determined as a function of pH from nonequilibrium electrophoretic mobility measurements. Schoenite appears to exhibit three charge reversals (CR) which can be explained based on surface hydrolysis reactions. The flotation behavior of schoenite is further considered based on solution chemistry calculations, electrophoretic mobility measurements, and microflotation results.

Jan 1, 2001

By W. E. Cobb

Mining companies, as developers of natural resources, are being forced to deal with the potential long-term liabilities of past, present, and future mining operations. As discussed in a previous paper (Cobb, et al., 1987), these liabilities can include solid waste disposal corrective action programs (state or federal actions), Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA), (Superfund) (state or federal actions), or natural resource damage claims (typically filed by state agencies and provisions specified in CERCLA). These potential liabilities are very real, and should dramatically impact the way a company views its exploration and development programs, and operating mines.

Jan 1, 1988

By J. J. Renton

The iron disulphide minerals, pyrite and to a lesser extent marcasite, are ubiquitous to coal and coal associated rocks and are the source of nearly all the environmental problems associated with the mining, processing and utilization of coal. The iron disulphides as well as the other minerals in coal exhibit systematic spatial pat- terns of distribution on both regional and local scales and show predictable associations, most of which are determined by the geochemical-sedimentological controls under which they form. It is the purpose of this paper to discuss the geochemical-sedimentological conditions responsible for the formation of coal minerals with special emphasis on the formation of iron disulphides, to illustrate the regional and local patterns of mineral occurrence within coal, to present the microscopic associations of the iron disulphides and finally, to discuss the most important single environmental aspect of the iron disulphide content of coal and coal associated rocks; the production of acid mine drainage.

Jan 1, 1986