Search Documents

By A. Acar, E. T. Tuzcu, Y. O. Vural

"In order to sustain the operations in chromite processing plants, due to concentrate selling cost, plants are in need of optimization in terms of capacity and recovery increase. In this study, DAMA Engineering carried out a methodological study for the purpose after a detailed sampling campaign in a plant which is situated in one the main chromite zones in Turkey; 1 The current status of the plant was investigated quantitatively with the bottlenecks, Plant overall efficiency in terms of recovery, Efficiencies of the particular equipment (mill, screen, gravity circuit), 2 A new circuit was proposed with the available equipment, 3 The new circuit that is product of modeling and experimental effort, was evaluated quantitatively as if it is a running plant, After 4-5 months continuous effort, the capacity of the plant was almost doubled (37 tph to 70 tph) and the plant overall recovery was increased from 48% to 63% by grinding adjustments and additional shaking tables theoretically. It was shown that the plant may move into profit with the minimum amount investment using readily available system. INTRODUCTION TO THE CURRENT PLANT The objective of the study is to increase the capacity and recovery of the chromite plant owned by Kurmel Group, Akmetal Inc. The complete study is given elsewhere (DAMA, 2016). The plant is situated in one of the main chromite zones in Turkey; Aladag. The current capacity of the plant is around 35 tph and the overall recovery declared by plant engineer is around 47 %. The chromite plant mainly has 3 units; crushing, grinding and gravitational circuits. The crushing circuit has 3 stages; a jaw crusher, a secondary cone crusher and a tertiary cone crusher operating in closed circuit with a vibrating screen with the aperture size of 15mm. In grinding circuit, a rod mill (2.44 6m x 3.6) and a ball mill (2.13 x 2.3m) are used for primary and secondary grinding, respectively. Derrick screens are used for the size separation. Additionally, for the size classification of the system, hydrosizers are used and each size fraction is sent to the shaking table sets. The middling product of the tables is subjected to re-grinding with a ball mill with the dimensions of 2.1 x 2.9 m. The capacity and the recovery are affected by several bottle necks; hydrosizers’ pure classification, primary/secondary mill power vs capacity problems, re-grinding product’s high slime content and so on. These combined factors made the plant to run in low recovery and capacity. Hence, DAMA was asked to make a study to investigate current status of the plant and propose a new solution to increase capacity and recovery of the plant. The conceptual flowsheet of the circuit is given in Figure 1 below."

Jan 1, 2017

By S. F. Diehl

Suites of monomineralic sulfide and carbonate minerals, as well as mine-waste composite samples, were analyzed using chemical and microanalytical techniques to understand behavior and bioavailability of mine waste elements such as Cu, Fe, Pb, or Zn. Petrographic, scanning electron microscopy (SEM), and laser-ablation inductively-coupled mass spectrometry (LA-ICP-MS) studies of mineralogical residence sites of trace elements are important because trace elements affect the chemical and physical behavior of minerals. Leachate solutions show that chalcopyrite, bornite, azurite, malachite, and galena are host to the trace elements Ag, Al, As, Cd, Co, Cr, Mn, Ni, Pb, and Zn. SEM studies reveal whether these trace elements occur within mineral inclusions or are substituted within lattice structures. SEM analysis reveals mineral phases not identified by X-ray diffraction (XRD), such as inclusions of sphalerite and cobaltite(?) within chalcopyrite.

Jan 1, 2010

By Jack E. Brockway

As tunnel boring machine technology has expanded, so has its range of application. Tunneling machines (TBM's) are tackling tasks today that fifteen years ago were considered "inappropriate". A case in point is incline/decline TBM boring. An incline or decline bore presents peculiar design considerations that differentiate it from a horizontal bore. This paper reviews those design considerations as they apply to TBM's, backup, muck handling and other tunneling subsystems. In addition, several abbreviated case studies are presented. By the review of real life tunneling techniques as well as design considerations, the "appropriateness" of TBM incline/ decline boring today becomes apparent. INCLINE Introduction In contemplating the impact of incline versus horizontal tunnel boring system design, the obvious consideration is gravity. Up-hill boring can be quite different than horizontal boring. Muck, water and machine weight all tend to slide down the incline. In addition, hydraulic and lubrication systems if unaltered, will find their fluids pooled in the lower corners contentedly ignoring such higher elevation items as gears and bearings. In order to address this inherent gravity problem, a review of

Jan 1, 1983

By Gordon R. Wicker, Willem P. C. Duyvesteyn, Robert E. Doane

A versatile acid leach process has been developed which is applicable to a broad range of oxide nickel ores. Inherent in this process are high recoveries of nickel and cobalt, as well as a relatively low energy consumption. These features extend the range of economic exploitation of laterite deposits to low grade limonites and to garnieritic ores not suitable for pyrometallurgical processing. Particular advantages can be realized in treating orebodies containing both limonite and garnierite and ores containing significant amounts of cobalt.

Jan 1, 1979

By J. P. Ulery

As a result of several recent methane/dust ignitions in surface auger and highwall mines, the U.S. Bureau of Mines investigated the occurrence of methane gas at these operations. Three mine sites were visited in western Kentucky and one in western Pennsylvania to collect run-of-mine coal samples for gas content determination using the modified-direct-method (MOM). Results indicate the samples emitted small quantities of methane, carbon dioxide, and nitrogen. Either methane or nitrogen was the predominant gas released. The same gases were released after crushing the samples for residual gas content; however, nitrogen was the primary component of this fraction. Total ~as contents ranged from less than 0.01 cm /g to 0.54 cm3/g. The hydrocarbon gases probably originated during coalification. Other gases may have originated partially as a byproduct of coalification and partially as a result of other, near-surface processes. The data suggest that although methane quantities are small, desorption could occur at near surface conditions prior to mining. The desorbed methane could accumulate as a free gas in fractures in the coal bed or roof rock. When these fractures are penetrated by the auger, methane could rapidly enter the whole atmosphere possibly creating explosive conditions.

Jan 1, 1994

By M. Zaske, E. R. Mortensen

"As mine operators continuously look for ways to improve functionality and increase capacity of their facilities, existing process equipment is often pushed to and past its designed limitations. As a result, equipment manufacturers are asked for economical solutions to meet redefined processing needs. Newmont USA (Newmont) in Nevada was faced with such a need in their Carbon-in-Leach (CIL) train. In a collaborative effort between Newmont and Derrick Corporation, tests were conceived to assess the viability of drop in replacement screen using a three dimensional screen panel. The urethane pyramid screen panel was designed to increase flux while maintaining the existing equipment footprint. The test is the end result of an ongoing research and development project that Derrick undertook in an effort to refine and upgrade their urethane screening media. The application of this new screening media is presented for this CIL application along with future plans to implement the technology in trash, safety, carbon dewatering, carbon sizing, and other scalping applications.INTRODUCTION In Spring of 2014, Process Machinery Associates (PMA), Derrick Corporation’s (Derrick) local area representative, met with Newmont USA (Newmont) to discuss the operation of the in tank screens in the carbon in leach (CIL) train at Twin Creeks, near Golconda, Nevada. The process was originally designed for 13,000 +tons per day (tpd) but has been steadily rising since the plant was commissioned and now Newmont requires 16,000 tpd to be processed. The original screens were running at their maximum capacity and Newmont required additional screening capacity to continue the upward trend in production. Physical separation by use of screening is one of mineral processing oldest methods. Screening media can be prone to blinding and pegging and the necessary support structures required for finer apertures result in smaller open areas. Therefore, more screening area generally requires larger panels and therefore larger machines, screening media that doesn’t blind, or a combination of both. In an effort to avoid larger machines, Derrick Corporation had been working on a revolutionary three dimensional panel which would add non blinding screen area in the same footprint of an existing machine. Alpha testing of the new screen panels began at Newmont Mill 2/5 (Carlin, Nevada) in July of 2013 and was still occurring when PMA approached Twin Creeks about beta testing a refined machine and pyramid panel. After presenting the initial results, Twin Creeks determined that an upgraded machine and pyramid panels would be a possible solution to meet production needs. The testing of a machine eliminated the risk of capital costs to Newmont and provided Derrick the opportunity to obtain additional data."

Jan 1, 2015

By ANGELA NAIR AVELAR, Reiner Neumann, PAULO R. G. BRANDÃO

The understanding of the influence of the different types of apatite on the performance of mineral processing of igneous phosphate ores is still a challenge due to the difficulty to explain why some types of apatite floats in the froth flotation cell and others do not under the same conditions. Three types of apatite were identified by means of cathodoluminescence (CL) images in flotation concentrate and tailing samples from the Catalão mine: predominantly blue apatite, followed by green apatite and less frequently yellow apatite. The chemical composition of these types of apatite was determined by electron microprobe analysis (EPMA) and LA-ICP-MS. Blue and green apatite respond well to the process, thus remaining in the concentrate, while yellow apatite remained in the tailings. Yellow apatite is the one bearing the lowest P2O5 content and the largest anionic and cationic sites substitution, followed by green apatite, whereas blue apatite is the most homogeneous, with highest P and Ca grades and lowest substitution level. A negative correlation of the amount of phosphorus with fluorine was observed. Furthermore, impregnation of iron oxide-hydroxides in the yellow apatite was also observed. Therefore, the low flotation behaviour is due to low crystallinity coupled with impregnation onto its surface.

Jan 31, 2022

By S. Brummelkamp, G. Van Weert

Separation of minerals by shape has received little attention, since minerals normally do not break into different shapes during crushing and grinding. However, comminution of consumer wastes generates opportunities for novel separations based on particle shape. For instance, ductile plastics are broken into longer curved shapes, whereas brittle plastics yield angular particles. Using spouting beds for particle separation in water requires controlling the spout's instability. The preferred geometry for such redesigned spouting beds is reported. Plastic cylinders, discs and spheres were separated as a function of rising water velocity and amount of particles in the system. By using 5 mm particles, differences in settling behavior could be video recorded.

Jan 1, 1999

By V. R. Degner

Comments Summary It is very interesting to review the technical changes which have occurred in the industrial practice of minerals flotation over the past two decades. In 1972, worldwide industrial flotation was dominated by 'mechanical' flotation machines having an individual cell volume less than 500 cu.ft. Manufactures, such as DENVER Eqpt. Co., OUTOKUMPU, WEMCO, GALIGHER (AGITAIR), AKKER, and later DORR-OLIVER, produced flotation machines featuring a mechanical rotating impeller which served to mix pulp and air, prior to flotation, and to keep the solid ore particles in suspension. While sharing this common mechanical impeller feature, the machine design of the various manufactures differed in detail; particularly in regard to the vertical location of the impeller in the cell and the means by which flotation air was brought into contact with the pulp within the rotor mechanism. A review of the existing technical literature in 1972 would identify academic research studies, particularly at Columbia University (N. Arbiter, C, Harris ...) aimed at comparing flotation cell design concepts, of the various machine manufactures, on a hydrodynamic basis. These research studies were confined to very small, laboratory bench size, flotation machines, and the benefits of incorporating hydrodynamic considerations in the scale-up of the existing 300 cu.ft. mechanical flotation technology to larger cells was not commonly practiced industrially. Technological advances in minerals flotation, over the past two decades, have been influenced by a variety of economic factors including the increasing development of lower grade ore bodies, the attractions of producing a higher grade final concentrate, and the economy of tails retreatment to improve overall plant recovery performance, and flotation system “optimization" became increasingly important through the 1970-80 time period. The trend toward processing lower grade ores led to higher tonnage mill operations, and stimulated the development of the very large capacity mechanical flotation machine for roughing and scavenging duty. In 1972, the 500 cu.ft. size flotation machine was being pilot tested and introduced to the industrial market. Today, 1993, individual cell volumes of 1500-3000 cu.ft. are operating successfully throughout the world, and well planned plant test programs have concluded that the very large flotation machine can achieve the same metallurgical performance level of its smaller predecessor. The large flotation machine development record clearly credits the incorporation of internal cell hydrodynamic considerations in guiding the scale-up of the mechanical flotation machine to large sizes. This guidance eliminated, or reduced significantly, costly in-plant prototype machine changes which increase Dramatically with increasing flotation machine size. Early in the 1980's, at approximately the time that flotation machines in the 1500 cu.ft. class were being introduced into the market, it became evident that the availability of the very large mechanical flotation machine brought with it the need for a systematic means to "optimize" the flotation system by relating flotation cell size, row length (i.e. number of cells per row), and flotation rougher, scavenger, and cleaner system configuration to the economic objectives of the concentrators' operating management. Flotation system optimization consists of quantifying the flotation process performance using a suitable model which relates the kinetic response of the trace specie and the gangue material to the cell overflow, and produces a numerical relationship between product grade and value recovery. The computer analysis technique has proven to be an invaluable tool in determining the kinetic model coefficients which characterize a given application, and is also used to apply the resulting model to a proposed minerals beneficiation situation seeking to "optimize" the flotation system by relating metallurgical grade-recovery performance, flotation cell size, and circuit arrangement, to plant space, installation, and operating costs. It is interesting to note that these same computer based kinetic flotation analysis techniques can be easily applied to quantitatively evaluate the effect of different chemical reagent strategies, and flotation air transfer, on process performance for a variety of candidate feed ore types.

Jan 1, 1993

By L. B. Hales

Color video or digital cameras have been installed over flotation cells to monitor color, bubble size, froth movement, and other characteristics. These systems are designed so that the camera provides flotation performance information just as any other sensor might. Factorial tests have been run to monitor and measure the variation in froth characteristics as a function of flotation control settings. Ultimately, it is envisioned that froth image sensors can be used to monitor and control the flotation performance as effectively and for less cost than current analytical systems.

Jan 1, 1999

By O. Noirot, H. C. Owens, P. D. Rao, D. E. Walsh, J. R. Mokka

Over a period of seven years (1989-1996) the Mineral Industry Research Laboratory (MIRL) University of Alaska Fairbanks, has investigated the effects of temperature, residence time, and particle size on the degree of low-rank coal (LRC) upgrading for a non-evaporative, hydrothermal drying process, also known as hot water drying (HWD). Three Alaskan LRCs were used in this study: Usibelli coal (Seam No. 4) from the Nenana Coal Field, Little Tonzona coal from near McGrath, and Beluga coal from the Beluga-Yentna field on the west side of Cook Inlet. Replicated, factorial tests were conducted. Experimental results indicate that most of the low-rank coal upgrading via HWD occurs rapidly within the first 10-20 minutes of residence time. Thereafter, the upgrading process slows down and over 100 minutes of additional residence time are required to produce similar percentage increases in coal properties to those achieved in the first 10- 20 minutes. The properties of the hot water dried products were very sensitive to process temperature. Calorific value, carbon and oxygen contents, equilibrium moisture levels and Hardgrove gindabilities all appear to change linearly with temperature within the 275°C to 325°C range.

Feb 24, 1997

By A. V. Castelli

The provinces of Guangxi, Guizhou, Hubei (and most recently Fujian) were the prime exporters of barite during this period. Guangdong and Shandong were exporters too but not major participants. These are all primarily agricultural areas so there existed a sufficient labor force willing to work in the mines to supplement their income from farming. During the early years, barite export pushed the existing transportation systems in these provinces to operational capacity. The mines from which this barite is extracted are located about 250 to 1,400 kilometers from the sea ports. Transportation of the ore from the mines to the ports follows a net-work that includes trucking to various rail-heads where it is then shipped via freight trains to ports for loading into seagoing vessels. in some instances, the barite travels by truck or train to the Yangtze River where it is then barged to an ocean port.

Jan 1, 1990

By Hou Xilun

Three production methods of rapid cold bonding and low temperature bonding pellets using sponge iron powder as a binder have been successfully developed. These methods differ from ordinary bonding method by no addition of salt and other catalyzers, no corrosion of equipment and no pollution of environment. Mechanism of pellet bonding is studied. Experiment shows that these pellets have good metallurgical properties. A semi-industrial test has proven the laboratory results, with the production of metallic pellets continuous and stable. These methods are substituted for traditional high temperature firing of oxidized pellets in direct reduction. As a result, the plant for oxidized pellets can be saved and substituted for grate in the grate-kiln system. Thus, 20% of the investment could be saved. Production cost may also be decreased. The production of cold bonding pellets does not need additional area.

Jan 1, 1980

Development of a permanent human base on the Moon for exploration requires a self sustaining system. This entails production and processing of limited amounts of raw material on the Moon. Any mining and construction activities on the Moon can only be performed by a robust excavation machine that can excavate a variety of material from loose surface regolith to consolidated (frozen) regolith with embedded rocks in the mixture. Meanwhile, limited amount of information on lunar regolith is available to develop and optimize a machine for given lunar ground conditions. Therefore, any excavator designed for use on the lunar surface should have the ability to adapt to a wide range of operating conditions. A prototype cutterhead for the lunar excavator was built and tested at the Kennametal facility in Latrobe PA A. This paper discusses the results of initial material characterization as well as full scale tests of a prototype cutterhead inrelevent material. A brief review of anticipated production rates under various assumed ground conditions will also be presented.

Jan 1, 2009

By Abdullah Arik

Verification of computer generated reserve models is essential since the computer does not automatically check the validity of methods and assumptions selected by the user and their results. For the computer to do model verification would require an expert system which would perform tests on the model and determine if the model is valid. Since such an expert system is not available, it is up to users to verify the models they develop.

Jan 1, 1995

On Dec. 20, 2013, an 8-m (26.2-ft) diameter Robbins hybrid single shield/earth pressure balance tunnel boring machine (EPB TBM) was launched to bore the Grosvenor decline tunnel for Australia?s Anglo American coal mine. The machine was built using onsite first time assembly (OFTA) in order to fit within a tight project schedule. Assembly at the remote jobsite near Moranbah, Australia took about four-and-a-half months, and then the machine was walked down into a launch tunnel. Two decline tunnels, at grades of 1:6 and 1:8, will be used for mine access to new coal seams. The hybrid machine is tackling mixed ground conditions ranging from sand and clay to varying types of sedimentary hard rock up to 120 MPa UCS, as well as coal seams. Methane gas is expected to be present throughout the tunnel, so the machine has been designed as explosion-proof-compliant to ERZ-1. ?Grosvenor is the first underground coal mine in Queensland to use a TBM for drift construction,? said Glenn Tonkin, Grosvenor project director. ?We are proud to be pioneering this technology.? Only about 300 m (984 ft) of ground in each decline tunnel is expected to require EPB mode, while the rest of the tunnel will be bored in hard rock mode. Thus, the design was optimized toward hard rock excavation.

By Fathi Habashi

CRYSTALLIZATION from aqueous solution is a simple and old method for the recovery of metal values from leach solution. Practically all the methods for the recovery of aluminum from clay are based on the crystallization of an aluminum salt from the leach solution. Differences in solubilities may be used to advantage for separating two metals from the same leach solution. The classical method of Marignac (1866), which makes use of the difference in solubilities of K2TaF7 and K2NbOF5 to separate niobium from tantalum, has been used successfully in the manufacture of these metals (Fig. 10-1). The slurry containing the metal oxides is dissolved in 70 % hydrofluoric acid, diluted, and heated near boiling. A potassium salt is added in sufficient quantity to form the complex fluorides of the niobium and tantalum present. The solution is filtered and allowed to cool. At room temperature most of the tantalum salt crystallizes out while the niobium remains in solution.

Jan 1, 1970

By A. Arik

An accurate estimation of mining block grades continues to be a challenging task for ore reserve practitioners. Two of the factors that affect the accuracy of the estimates are the estimation method used and the variability of the mineralization in the deposit. The objectives of the study are twofold: Firstly, to see how different estimation methods perform on a given deposit. Secondly, to determine the impact of particular nature of the mineralization on the results. The comparison of several estimation methods for the prediction accuracy is performed using the conditional simulation results as the basis.

Jan 1, 2000

By F. Ansheng

Though it becomes increasingly important with the valuable minerals in their deposits tending to be fine and poor, the solid and liquid separation remains difficult especially when the particles are of micrometer size and of low density. Almost of all conventional thickeners result in that fine particles lose into overflows which often costitutes a loss of potentially valuable resources as well as an environmental hazard. The addition of flocculations may improve the settling of solids but may also not work well for the final removal of fine particles from the overflows (Ref.1).

Jan 1, 1990

By Yi Luo

Subsidence events occurring above inactive room-and-pillar (R&P) mines, including abandoned mines or sealed portions of active mines, are classified as unplanned subsidence, because of their timing and distribution are unpredictable. When investigating such subsidence cases, many uncertainties exist and disputes often focused on whether the observed structural damages are caused by mine subsidence or other natural or artificial causes. However, solid evidence to identify the cause is often lacking. In order to conduct a complete and impartial investigation, thorough knowledge of subsidence theories and other ground control topics, as well as broad experience, are required.

Jan 1, 2011