Search Documents

By Mike S. Ness, Allan G. Provost

High speed drilling, mucking, and hauling equipment was used in driving approximately 2.16 km(7100 ft) of lower power tunnel in quartz diorite for the Tyee Lake Hydroelectric Project near Wrangell, Alaska. The .91 m(36 in.) guage rail mounted equipment included a Tamrock 2-boom electric/hydraulic drill jumbo, a Haggl and 8HR mucker , and 3 Hagglund 115C shuttle cars. Several other innovative techniques allowed maximum advance rates of up to 17.5 m/day(57ft/day) in the 3 m(10ft) horseshoe section. Average tunnel advance was approximately 11 m(day(35.4 ft/day). The primary difficulties preventing full utilization of the equipment potential were the operators' "learning curve", the need for complete retraining of all personnel in the new methods, and minor sections of faulted ground.

Jan 1, 1983

By Louis P. Gignac

The Lac Shortt gold deposit is located in Northwestern Quebec, at some 115 km west of the Opemiska Division and 380 km northeast of the Lac Dufault Division, as shown on Figure 1. Falconbridge's exploration crews drilled the first six holes in the gold-bearing ore zone in 1979. After further diamond drilling from surface in 1980, the decision was taken to carry out an underground exploration program. A three-compartment shaft was sunk to a depth of 340 metres in 1981 and 1982; it was followed by an extensive exploration program, which included 1073 metres of cross-cutting and footwall drifting, 645 metres of ore drifting and 11 200 metres of diamond drilling. The underground work was completed by mid-winter 1983. It was followed by a complete feasibility study of the Lac Shortt Project. After some $Can 14.2 millions in exploration expenditures, the Board of Directors of Corp. Falconbridge Copper approved in July 1983 additional expenditures of $Can 45 millions to bring the Lac Shortt Mine in production at the capacity of 261 000 tonnes per year. Gold price was $US 425 per ounce at the time.

Jan 1, 1985

By Samuel J. Gambino

Preliminary recommendations for the Upper Northwest Interceptor 1&2 specified installation of reinforced concrete pipe using pipe-jacking methods. However, a larger one-pass tunnel constructed using precast segmental lining would provide additional storage volume. The risk of encountering unexpected conditions or events and the resulting cost impacts could differ significantly for these two options. A probabilistic life-cycle cost analysis of these alternatives was performed. This paper discusses the construction alternatives considered, the risk assessment methodology used to evaluate these alternatives, the input parameters and risk factors used in this analysis, and the recommended project which is currently being constructed.

Jan 1, 2008

By Ronald K. Frobel, Christopher J. Wienecke

Geomembrane systems and associated geosynthetics such as geotextiles, geonets, geogrids and geocomposites have been used in precious metal heap leach and tailings facilities for many years. Geomembranes have been used in the heap leach process in pad design and solution recovery ponds as well as associated collection channels as the primary liquid barrier to contain and collect metal bearing leach solution. Geomembrane systems offer an effective, low cost alternative to other containment methods such as compacted low permeability soils, asphalt or concrete. In the 19BO's, rigid High Density Polyethylene (HOPE) liners were used to a great extent with a gradual transition to the use of the more flexible Very Low Density Polyethylene (VLDPE) and Polyvinyl Chloride (PVC). These three geomembrane systems have been used successfully in precious metal heap leach solution containment. Predominant material thicknesses have been 30 and 40 mil for PVC, 40 and 60 mil for HOPE and VLDPE. Variants in recent years have included roughened HDPE and VLDPE to provide higher surface friction characteristics, as well as newer polymer materials such as polypropylene. In addition to providing an economical method for providing enhanced solution recovery, geomernbranes are also providing the primary liquid barrier for prevention of groundwater contamination. Because heap leach solution chemical components and dissolved metal constituents are classified as toxic substances, they are subject to environmental regulation. Many regulatory agencies are still developing guidelines for heap leach pad design, however a geomernbrane liner system is often used as a single liner or in conjunction with other materials to form composite double or even triple lined systems. "Other" materials can include alternate layers of drainage aggregate, geotextiles, clay layers and other geomembrane or geocomposite layers.

Jan 1, 1993

By D. DeGagné, E. De Souza, J. F. Archibald

A comprehensive survey of minefill practices in underground mines in Canada has been conducted. The survey was designed to cover the entire filling operation for individual mines from feed to the preparation plant, to underground transportation, and to stope placement. The questionnaire examined such areas as mining method utilized, the purpose of backfilling, backfill formulations, including binding and chemical additives, slurry properties, transportation parameters, stope preparation procedures, backfill placement properties, fill instrumentation, and costs. This paper presents the current state of backfill usage in Canada, identifies trends in minefill practices and provides mine operators with an updated database to compare their own practices with modern trends throughout the industry.

Jan 1, 2001

By J. Bouchard, V. Aubé, A. Desbiens, R. del Villar

The metallurgical performance of column flotation is determined by the concentrate grade and recovery. Although the former can be continuously measured using an on-stream analyzer, the latter must be estimated by a material balance calculation based on seldom verified steady-state assumptions. Consequently, the automatic control and optimization of flotation columns should be performed using secondary variables having a strong influence on the metallurgical performance, such as froth depth, gas hold-up or bubble surface area flux and bias. The aim of this paper is to present a method to get froth depth and bias measurements using virtual sensors. Fractional factorial experiment design for the neural network calibration of the bias sensor, pilot plant results, and eventual industrial applications – including the possibility of achieving effective real-time optimization from bias and froth depth measurements – will also be discussed.

Jan 1, 2003

By L. Alan Weakly

Page one is missing from book

Jan 1, 1982

By V. I. Ryaboy, V. A. Luknitsky, V. V. Zuyev

The action has been studied of three types of reagents used as intensifiers in grinding copper-molybdenum, sulphide-sheelite, polymetallic and other types of ores, namely N-donor, dispersant, and surface-acting agents. It has been proved that, depending on the type of ore treated, the C (N-donor) and C-170 (dispersant) reagents increase the yield of the principal size fraction of 0.074mm by 8-16% (relative). Consequently, the specific mill capacity improves by 13-21 %. The C and C-170 reagents activate the subsequent flotation stage and are thus beneficial to the mineral recovery. The surface-acting reagents affect the mineral grinding process to a lesser extent. The intensifying action of the reagents is attributed to the effective crushing energy decrease (lower crack-resistance factor) or else to the slime-dispersing effect of the reagents. The pilot-plant test results for the C reagents are given. Both C and C170 reagents are commercially produced and recommended for use at a number of concentrators in Russia, Uzbekistan and Kazakhstan.

Jan 1, 1995

By Hervé Le Bissonnais, Jean-Pierre Janin, Anne Bergère, Pierre Renier

"The most important impact on the environment of a tunnel excavation is the creation of surface settlements. Nowadays, the mechanized tunneling allows minimizing the settlements, applying a confinement pressure which counterbalances the ground de-confinement. It is thus essential to determine the correct amount of confinement pressure. In this paper, the authors present a 3D numerical study simulating the EPB-TBM excavation of a water tunnel, in the Flanders clays (north of France). Firstly, a simplified 3D simulation, based on the concept of instantaneous longitudinal settlement curve, was performed to predict the surface settlements for different values of heading confinement pressures. Secondly, the same pressures were tested by the EPB-TBM in a monitoring zone. The comparison between the prediction settlements and the measurements was very satisfactory and allowed validation of the numerical approach and the choice of the optimal confinement pressure value for a sensitive area of the project. INTRODUCTION The excavation of a tunnel can create displacements of the surrounding soil which may affect existing structures and generate unacceptable dysfunction. The development of the closed shield tunneling has permitted to reduce the volume loss generated around the excavation and consequently the surface settlements. In this case, as explained by different authors (Clough et al., 1985; Kastner et al., 1996; Mair and Taylor, 1997), the ground movements are influenced by the TBM works: the heading confinement pressure, the shield overcutting and conicity, the annular void grout injection parameters, the segment concrete lining rigidity, the consolidation of the grout. Hence, in the tunnel design, it is important to take into consideration these different processes of the excavation works to simulate correctly the tunneling process."

Jan 1, 2016

By S. Behl

In the selective flocculation process, polymers with specific functional groups can yield highly selective adsorption and, therefore, high separation efficiency. Selectivity in polymer adsorption may also be attained by specific additives that inhibit the adsorption of the flocculant on some solid surfaces but not on others. Generally, these additives have a different chemical nature than the flocculant. In this study, the lower molecular weight fraction of the flocculant was successfully evaluated as a site blocking agent, leading to higher separation efficiency than obtained otherwise.

Jan 1, 1993

By D. R. Lowe

Silicic volcanic ash and its alteration product, bentonite (montmorillonite and cristobalite), occur widely within sedimentary phosphate deposits. The genetic link, if any, between volcanism and phosphate deposition has yet to be satisfactorily established The phosphatic member of the Santa Margarita Formation (upper Miocene) in northwestern Ventura County, California, consists of approximately 15 per cent volcanic ash and bentonite. Ash and bentonite units greater than one foot thick can be subdivided into a lower zone of airfall origin and an upper zone of mixed ash and terrigenous detritus washed in from surrounding land areas. This upper zone also contains up to 20 percent phosphate pellets. These thick volcaniclastic units are typically overlain sharply by thin beds (less than 6 inches thick) of relatively pure, silica-cemented pelletal phosphorite. The shelf basin in which the phosphatic sediments accumulated was characterized by quiet, reducing but not euxenic bottom waters; Abundant decaying organic debris, mainly diatoms, served as a reservoir of readily available phosphate. The sudden influx of a large volume of silicic volcanic ash into this basin and its subsequent alteration to montmorillonite had two profound effects on thechemistry of the interstitial and bottom waters: (1) during alteration magnesium was removed from these waters and incorporated into the montmorillonite lattice, and (2) the pH of these waters increased as alteration progressed Both of these effects led to the crystallization in the bottom waters of carbonate fluorapatite. This accumulated as thin phosphorite beds immediately above the volcaniclastic units.

Jan 1, 1972

By S. K. Kawatra

For efficient control of particle size in a wet grinding circuit, three alternative methods for monitoring pro- duct particle size are available. These methods are based on: 1. Ultrasonic wave absorption. 2. Low-angle forward scattering of a laser beam. 3. Inferential sizing techniques. The relative advantages and disadvantages of each technique are discussed. A particle size monitor can be used on a single grinding line to control the product particle size. To minimize the number of particle size monitors at an operation consisting of many similar grinding lines, a portable multi-stream on-line analyzer can be used. The paper outlines the design and the operational characteristics of the portable multi-stream online analyzer.

Jan 1, 1979

By Robert Irvine

Exploration activity for diamonds in Canada has recently experienced a dramatic increase. Disclosure of a diamond discovery exhibiting features of a potentially economic deposit contained in a kimberlite pipe in the Lac de Gras area of Canada's Northwest Territories has sparked substantial interest in-Canada and abroad and has triggered the largest staking rush in terms of area in the history of Canadian exploration. In this paper, we report on the nature and extent of current exploration activity in Canada for diamonds (with special attention to Arctic regions), the results of this activity to date, and the context in terms of current world markets for diamonds.

Jan 1, 1995

By K. N. Han, X. Xie

The dissolution behavior of palladium powder in thiourea solutions was investigated. The variables studied were temperature, stirring speed and the concentrations of thiourea, acid and ferric ion. Palladium was found to be soluble in thiourea solutions in the presence of an oxidant such as ferric ion. The dissolution of palladium in thiourea solutions was believed to be chemical-reaction controlled, with an apparent activation energy of about 25.3 kJ/mol.

Jan 1, 1997

By L. A. Weakly, D. A. Weiss, R. B. Crookston

A presentation of experience gained from using mechanical and conventional equipment for excavating shafts, raises, tunnels and other openings in various Colorado oil shale mining properties.

Jan 1, 1983

By Brian H. Jasperse, Nicholson Peter J.

Gravity retaining walls have been constructed using Deep and Shallow Soil Mixing (DSM and SSM) since 1991 in the United States. These walls, for both temporary and permanent uses, were constructed by mixing cement with in-situ soils over a volume containing 100% of the required gravity wall zone. Modern design techniques have reduced costs substantially by forming the required gravity wall section as a composite mass. Using ratios of 15-35% by volume, treatment f the ground forming the required gravity section has reduced the cost from about $40 to about $20 per square foot. Design, construction and actual performance of these gravity walls are presented.

Jan 1, 1999

By Mustafa Kumral

The study area is located in the Alpine-Himalayan zone in Turkey. Geologically, this is a very complicated region, and the rock units generally are divided into two groups as either allochthonous and autochthonous. Tectono-stratigraphically, the units are Paleozoic quartzite, black limestone, arkosic sandstone, interlaminated radiolarite and Triassic limestone, thick Jurassic limestone, detritic limestone with alternating Eocene Nummulites beds and cream-green marl, Miocene siltstone, and ophiolite. Trachyte, trachyandesite, feldspathoidal trachyandesite porphyry, tuff, and pumice formed by volcanism during the Plio-Quaternary also are present. Recent alluvium and slope detritus locally cover all the other rock units. A number of sulfur outcrops occur in the area. Among them are outcrops at Keciborlu, Yelliyatak Hill, Buyuk, and Kucuk Kukurt Dere. The most important sulfur deposits are found in volcanic tuff and siltstone-marl, and they include highly organic material. Sulfur may accumulate around recent gas diffusions and also as massive formations. The information about local geology and sulfur isotopes shows that the sulfur originated From the crust and probably comes from organic-rich Paleozoic and Triassic units. The sulfur did not move between Triassic and Pliocene time. However. Plio-Quaternary volcanism did cause movement of the sulfur, and this was followed by formation of the secondary sulfur due to post-tectonic thermal activities and the mixing of other surface waters.

Jan 1, 1999

By Faruk Oksuz, Clay Haynes, Miguel Sanchez, Patrick Finn, Roger J. Maurer

The Milwaukee Metropolitan Sewerage District’s (MMSD)’s challenges of basement flooding and wet weather sewer overflows are being creatively addressed with the Northwest Side Relief Sewer tunnel. The $132 million, 20-foot diameter, and37,740 feet long conveyance and storage tunnel excavation in dolomite at depths reaching 165 feet below ground surface has been successfully completed within13 months in April 2004. This paper includes Owner’s perspective on the overall project, and the design and construction details by the Designer and the Contractor. The project contract documents included a comprehensive Geotechnical Data Report and the Geotechnical Baseline Report.

Jan 1, 2005

By Qing-Wang Hao

In this paper, the authors attempt to develop engineering based approaches for estimating safety factors against pillar and floor failures and predicting likelihood of subsidence events over abandoned coal mines in Illinois. There are two critical problems involved in the analysis: determination of geotechnical properties, and consideration of time effect. The authors attempt to solve the problems by generating hypotheses, which are used to modify existing engineering models for estimating pillar and floor safety factors. The modified models are validated using data from two well established databases of subsidence events over active and abandoned mines in Illinois. The data analysis suggests that most of the trough type subsidence events in Illinois were caused by floor failures rather than pillar failures. The subsidence incubation period seems to be directly related to initial floor safety factors at the time of mining. This correlation can be used to predict the likelihood of subsidence and to assess subsidence risks within both spatial and temporal contexts where detailed mine maps are available.

Jan 1, 1986

By Heinrich Schubert

In many unit operations, there are more or less developed turbulent flow conditions. Then, macroturbulence influences the transport phenomena of the particles and microturbulence controls the stresses acting on fluid and solid particles or agglomerates as well as the collisions between particles. Consequently, these conditions have to betaken into consideration for modeling and optimization. The results of corresponding approaches are demonstrated taking classification and flotation as examples. But, at present, extensive simplifying assumptions have to be made.

Jan 1, 1989